SCR-584 radar

Last updated
SCR-584
Exterior view of SCR-584.jpg
Exterior view. All operational equipment was housed inside, although the M-9 director, and electrical generators were separate. The antenna retracts into the van for travel.
Country of originUS
Designer MIT Radiation Laboratory
FrequencyFour bands around 3,000 MHz
PRF 1707 pulses per second
Pulsewidth0.8 microsecond
Range70,000 yd (40 mi; 64 km)
Diameter6 ft (1.8 m)
Azimuth 360 degrees
Elevation-175 mils (-9.8 degrees) to +1,580 mils (+88.9 degrees)
PrecisionRange error: 25 yards; azimuth error: 1 mil (0.06 degree); elevation accuracy: 1 mil (0.06 degree)
Power250 kW
RelatedData from U.S. War Department Technical Manuals TM11-1324 and TM11-1524 (published April 1946 by the United States Government Printing Office)

The SCR-584 (short for Set, Complete, Radio # 584) was an automatic-tracking microwave radar developed by the MIT Radiation Laboratory during World War II. It was one of the most advanced ground-based radars of its era, and became one of the primary gun laying radars used worldwide well into the 1950s. A trailer-mounted mobile version was the SCR-784.

Contents

In 1937, America's first fire-control radar, the SCR-268 radar, had proven to be insufficiently accurate due in part to its long wavelength. In 1940, Vannevar Bush, heading the National Defense Research Committee, established the "Microwave Committee" (section D-1) and the "Fire Control" division (D-2) to develop a more advanced radar anti-aircraft system in time to assist the British air-defense effort. In September of that year, a British delegation, the Tizard Mission, revealed to US and Canadian researchers that they had developed a magnetron oscillator operating at the top end of the UHF band (10 cm wavelength/3 GHz), allowing greatly increased accuracy. Bush organized the Radiation Laboratory (Rad Lab) at the MIT to develop applications using it. This included a new short-range air-defense radar.

Alfred Lee Loomis, running the Rad Lab, advocated the development of an entirely automatic tracking system controlled by servomechanisms. [1] This greatly eased the task of tracking targets and reduced the manpower needed to do it. They were also able to take advantage of a newly developed microwave switch that allowed them to use a single antenna for broadcast and reception, greatly simplifying the mechanical layout. The resulting design fit into a single trailer, could provide all-sky search and single target tracking, and followed the targets automatically. In close contact with the Rad Lab, Bell Telephone Laboratories was developing an electronic analog gun-director that would be used in conjunction with the radar and servo-actuated 90 mm anti-aircraft guns.

The radar was intended to be introduced in late 1943, but delays meant the SCR-584 did not reach field units until early 1944. They began replacing the earlier and more complex SCR-268 as the US Army's primary anti-aircraft gun laying system as quickly as they could be produced. They proved easier to use in the field than the less advanced Canadian/British GL Mk. III radar, and many SCR-584's were rushed to England where they were an important part of the defences developed to counter the V1 flying bomb. By the end of the war they had been used to track artillery shells in flight, detect vehicles, and reduce the manpower needed to guide anti-aircraft guns.

Background

In September 1940, a group of British physicists and engineers visited their counterparts in the US in what became known as the Tizard Mission. The goal of the meetings was to exchange technical information that might be of use to the war effort. The British were hesitant to give away too much information without getting anything in return, and initial progress was slow. When they moved onto the topic of radar, the British team was surprised to learn that the US was in the process of developing two systems similar to their own existing Chain Home, the Navy's CXAM and the Army's SCR-270. This began to break the ice between the two groups.

Two previous attempts at radar-controlled gun-laying were notable. In Britain, the 75 MHz GL Mk. I radar was used in connection with a Vickers predictor; and in the U.S., the 200 MHz SCR-268 was combined with the Sperry M-4 predictor. [2] Neither the US or UK systems had the accuracy needed to directly lay their associated guns, due to their long wavelengths. The US delegates then mentioned the Navy's work on a 10 cm wavelength radar, which could provide the required resolution with relatively small antennas, but their klystron tube had low power and was not practical.

This was the moment the British team had been waiting for. Edward George Bowen produced one of the earliest cavity magnetrons from a box and showed it to the other researchers. He explained that it also worked at 10 cm wavelength, but offered higher power - not just than the Navy klystrons, but even the US's existing long-wave radars. One US historian later described it as the "most valuable cargo ever brought to our shores". [3]

The potential of the device was obvious, and the US group, informally known as the Microwave Committee, immediately switched their efforts to the magnetron. They had their own examples built in US labs within weeks. They also began developing the other technologies presented at that meeting, including an aircraft interception radar and a radio navigation system that became LORAN. The expansion of the Committee led to it being renamed the Radiation Laboratory (RadLab) in 1940.

Development

A formal proposal for a SCR-268 replacement was made by the Signal Corps in January 1941, by which point the RadLab had already formed what they knew as Project 2 to develop this advanced gun laying radar. MIT proposed an advanced system with automatic search, tracking and the ability to directly aim the guns. This was a field MIT was particularly knowledgeable in due to work in their Servomechanisms Lab. At the same time, British and Canadian teams began work on versions of a simpler system that they hoped to deploy by 1942 -- the GL Mk. III, which was a microwave version of the earlier lobe-switching VHF radar sets. [4] The Radiation Lab kept in close contact with the Canadian team during these developments.

The RadLab team, overseen by Lee Davenport, had a prototype radar system running in April 1941. [5] To test the automatic aiming system, they attached the outputs from the radar to a gun turret taken from a Boeing B-29 bomber, removing the guns and replacing them with a camera. A friend then flew his light plane around the area while the camera periodically took photographs, and on 31 May the system was able to accurately track the aircraft. Work then started on making the system suitable for field use, mounting the entire system in a single trailer with the 6-foot antenna on top. Known as XT-1, for eXperimental Truck-1, the system was first tested at Fort Monroe in February 1942.

Field deployment of the SCR-584 on Peleliu during World War II. The high elevation angle of the dish combined with a lack of visible activity suggests that the radar is in its helical scan mode. Scr-584 setup.jpg
Field deployment of the SCR-584 on Peleliu during World War II. The high elevation angle of the dish combined with a lack of visible activity suggests that the radar is in its helical scan mode.

Work also started on a suitable gun-laying computer that could use electrical, as opposed to mechanical, inputs for pointing data. Bell Labs delivered an analog computer known as the M9 Gun Director for this role. The M9 had four sets of outputs, allowing a single M9 to control four of the Army's standard 90 mm M1 guns. The entire system, including the M9, was demonstrated in complete form on 1 April 1942. A contract for over 1,200 systems arrived the next day. Bell also worked on their own microwave radar as a backup project.

The SCR-584 was extremely advanced for its era. To achieve high accuracy and measure both azimuth and elevation with one antenna, it used a conical scanning system, in which the beam is rotated around the antenna's axis to find the maximum signal point, thus indicating which direction the antenna should move in order to point directly at the target. The idea was proposed by Alfred Loomis, the director of section D-1 of the National Defense Research Committee. In October 1940, it was adopted for the "wholly-automatic-tracking" radar project. Conical scanning was also adopted in 1941 for the Navy's 10 cm fire-control radar system, [6] and it was used in the German Würzburg radar in 1941. The SCR-584 developed the system much further, and added an automatic tracking mode. [7] Once the target had been detected and was within range, the system would keep the radar pointed at the target automatically, driven by motors mounted in the antenna's base. For detection, as opposed to tracking, the system also included a helical scanning mode that allowed it to search for aircraft. This mode had its own dedicated PPI display for easy interpretation. When used in this mode the antenna was mechanically spun at 4 rpm while it was nudged up and down to scan vertically.

The system could be operated at four frequencies between 2,700 and 2,800 MHz (10–11 cm wavelength), sending out 300 kW pulses of 0.8 microseconds in duration with a pulse repetition frequency (PRF) of 1,707 pulses per second. It could detect bomber-sized targets at about 40 miles range, and was generally able to automatically track them at about 18 miles. Accuracy within this range was 25 yards in range, and 0.06 degrees (1 mil) in antenna bearing angle (See Table "SCR-584 Technical Characteristics"). Because the electrical beam width was 4 degrees (to the -3db or half-power points), the target would be smeared across a portion of a cylinder, so as to be wider in bearing than in range (i.e., on the order of 4 degrees, rather than 0.06 degrees implied by the mechanical pointing accuracy), for distant targets. Range information was displayed on two "J-scopes", similar to the more common A-line display, but arranged in a radial pattern timed to the return delay. One scope was used for coarse range, the other for fine.

Operational use

Operators console for the SCR-584. Scr-584 console.jpg
Operators console for the SCR-584.

Although the first operational unit was delivered in May 1943, various bureaucratic problems led to it being delayed in being delivered to the front-line troops. The SCR-584 was first used in combat at Anzio in February 1944, where it played a key role in breaking up the Luftwaffe's concentrated air attacks on the confined beachhead. The SCR-584 was no stranger to the front, where it followed the troops, being used to direct aircraft, locate enemy vehicles (one radar is said to have picked up German vehicles at a distance of 26 kilometers), and track the trajectories of artillery shells, both to adjust the ballistic tables for the 90 millimeter guns, and to pinpoint the location of German batteries for counter-battery fire. After D-Day, the SCR-584 was used in the rapidly shifting very front lines to guide planes to their targets with increased accuracy. For example, the Control Net Systems Group of the 508th Sq of the 404th Fighter Bomber Group, 9th Air Force ran the SCR-584. From 14 Jul 1944 until 27 Oct 1944 they were attached to Sec 1 Co A, 555th Sig Aircraft Warning Battalion and served in fluid, forward positions.

The SCR-584 was so successful that it was adapted for use by the United States Navy. CXBL, a prototype of the navy version, was mounted on the carrier USS Lexington in March 1943, while the production version, the SM, built by General Electric, was operational on the carriers USS Bunker Hill and USS Enterprise by October 1943. A lighter version of the system was also developed, the SCR-784. The only real difference was that the new design weighed 12,000 lb, whereas the original was 20,000.

Davenport waterproofed a number of the radar sets so that they could be carried aboard the Allied armada launching the Normandy landings on D-Day.

Automatic gunlaying (using, among others, the SCR-584 radar) and the proximity fuze played an important part in Operation Diver, (the British operation to counter the V1 flying bombs). Both of these had been requested by AA Command and arrived in numbers, starting in June 1944, just as the guns reached their free-firing positions on the south eastern coast of England. Seventeen per cent of all flying bombs entering the coastal 'gun belt' were destroyed by guns in the first week on the coast. This rose to 60 per cent by 23 August and 74 per cent in the last week of the month, when on one extraordinary day 82 per cent were shot down. The rate increased from one V-1 for every 2,500 shells fired to one for every hundred.

After the war, the radar was adapted for use in the AN/MPQ-12, and AN/MPM-38 systems, a US Army field artillery missile system (MGM-5 Corporal). A modified version was also used to control and beacon-track (using an onboard transponder) the CORONA spy satellite.

In 1953, the SCR-584-Mod II was used for tracking the Redstone rocket, its range extended to 740 km by the use of an onboard transceiver. [8]

Despite using vacuum tubes and being powered by an analog computer, some specimens of the SCR-584 are still operational today. In 1995 the first Doppler On Wheels (DOW) radar adapted the MP-61 pedestal from an SCR-584 for use in a mobile weather radar. [9] Using this pedestal, the DOWs created the first maps of tornado winds, discovered hurricane boundary layer rolls, and pioneered many other observational studies. The pedestal housed first a 6' then an 8' antenna. Later the original motors were replaced with more powerful brushless versions for faster scanning in high winds. Three DOWs are now operated as National Science Foundation facilities by the Center for Severe Weather Research. One is found at the National Severe Storms Laboratory in Norman, Oklahoma, where the 584 pedestal is the platform for the new Shared Mobile Atmospheric Research & Teaching Radar, or SMART-R.

Soviet derivatives

American engineer and convicted spy Morton Sobell stole plans for the SCR-584 and provided them to the Soviet Union. Military experts believe that the technology was then used against the United States during the Korean and Vietnam wars. [10] The Soviet SON-9 (Fire Can), SON-30 (Fire Wheel), and SON-50 (Flap Wheel) radars were all derivatives of this radar. [11]

K-83 dolly

General Electric constructed a dolly for the SCR-584, designated K-83. The K-83 was designed to provide a semi-trailer hitch (fifth wheel) wheels and bar to engage a pintle, allowing smaller vehicles to move the SCR-584.[ citation needed ]

See also

Related Research Articles

<span class="mw-page-title-main">Radar</span> Object detection system using radio waves

Radar is a system that uses radio waves to determine the distance (ranging), direction, and radial velocity of objects relative to the site. It is a radiodetermination method used to detect and track aircraft, ships, spacecraft, guided missiles, motor vehicles, map weather formations, and terrain.

<span class="mw-page-title-main">Würzburg radar</span> Ground-based gun laying radar for the Wehrmachts Luftwaffe and German Army during World War II

The low-UHF band Würzburg radar was the primary ground-based tracking radar for the Wehrmacht's Luftwaffe and Kriegsmarine during World War II. Initial development took place before the war and the apparatus entered service in 1940. Eventually, over 4,000 Würzburgs of various models were produced. It took its name from the city of Würzburg.

<span class="mw-page-title-main">Fire-control radar</span> Narrowly focused radar beam whose reflected signal is used to obtain a missile lock-on

A fire-control radar (FCR) is a radar that is designed specifically to provide information to a fire-control system in order to direct weapons such that they hit a target. They are sometimes known as narrow beam radars, targeting radars, tracking radars, or in the UK, gun-laying radars. If the radar is used to guide a missile, it is often known as a target illuminator or illuminator radar.

<span class="mw-page-title-main">SCR-268 radar</span> U.S. Armys first radar system

The SCR-268 was the United States Army's first radar system. Introduced in 1940, it was developed to provide accurate aiming information for antiaircraft artillery and was also used for gun laying systems and directing searchlights against aircraft. The radar was widely utilized by both Army and Marine Corps air defense and early warning units during World War II. By the end of World War II the system was already considered out of date, having been replaced by the much smaller and more accurate SCR-584 microwave-based system.

<span class="mw-page-title-main">Conical scanning</span> System used in radar to improve accuracy

Conical scanning is a system used in early radar units to improve their accuracy, as well as making it easier to steer the antenna properly to point at a target. Conical scanning is similar in concept to the earlier lobe switching concept used on some of the earliest radars, and many examples of lobe switching sets were modified in the field to conical scanning during World War II, notably the German Würzburg radar. Antenna guidance can be made entirely automatic, as in the American SCR-584. Potential failure modes and susceptibility to deception jamming led to the replacement of conical scan systems with monopulse radar sets. They are still used by the Deep Space Network for maintaining communications links to space probes. The spin-stabilized Pioneer 10 and Pioneer 11 probes used onboard conical scanning maneuvers to track Earth in its orbit.

<span class="mw-page-title-main">MIT Radiation Laboratory</span> Research facility in Cambridge, Massachusetts

The Radiation Laboratory, commonly called the Rad Lab, was a microwave and radar research laboratory located at the Massachusetts Institute of Technology (MIT) in Cambridge, Massachusetts. It was first created in October 1940 and operated until 31 December 1945 when its functions were dispersed to industry, other departments within MIT, and in 1951, the newly formed MIT Lincoln Laboratory.

Signal Corps Laboratories (SCL) was formed on June 30, 1930, as part of the U.S. Army Signal Corps at Fort Monmouth, New Jersey. Through the years, the SCL had a number of changes in name, but remained the operation providing research and development services for the Signal Corps.

Radar in World War II greatly influenced many important aspects of the conflict. This revolutionary new technology of radio-based detection and tracking was used by both the Allies and Axis powers in World War II, which had evolved independently in a number of nations during the mid 1930s. At the outbreak of war in September 1939, both the United Kingdom and Germany had functioning radar systems. In the UK, it was called RDF, Range and Direction Finding, while in Germany the name Funkmeß (radio-measuring) was used, with apparatuses called Funkmessgerät . By the time of the Battle of Britain in mid-1940, the Royal Air Force (RAF) had fully integrated RDF as part of the national air defence.

<span class="mw-page-title-main">Type 271 radar</span> British WWII naval surface search radar

The Type 271 was a surface search radar used by the Royal Navy and allies during World War II. The first widely used naval microwave-frequency system, it was equipped with an antenna small enough to allow it to be mounted on small ships like corvettes and frigates, while its improved resolution over earlier radars allowed it to pick up a surfaced U-boat at around 3 miles (4.8 km) and its periscope alone at 900 yards (820 m).

<span class="mw-page-title-main">AI Mark VIII radar</span> Type of air-to-air radar

Radar, Airborne Interception, Mark VIII, or AI Mk. VIII for short, was the first operational microwave-frequency air-to-air radar. It was used by Royal Air Force night fighters from late 1941 until the end of World War II. The basic concept, using a moving parabolic antenna to search for targets and track them accurately, remained in use by most airborne radars well into the 1980s.

<span class="mw-page-title-main">GL Mk. I radar</span>

Radar, Gun Laying, Mark I, or GL Mk. I for short, was an early radar system developed by the British Army to provide range information to associated anti-aircraft artillery. There were two upgrades to the same basic system, GL/EF and GL Mk. II, both of which added the ability to accurately determine bearing and elevation.

<span class="mw-page-title-main">Radar, Anti-Aircraft No. 3 Mk. 7</span> Mobile anti-aircraft gun

Radar, Anti-Aircraft Number 3 Mark 7, also widely referred to by its development rainbow code Blue Cedar, was a mobile anti-aircraft gun laying radar designed by British Thomson-Houston (BTH) in the mid-1940s. It was used extensively by the British Army and was exported to countries such as Holland, Switzerland, Sweden Finland and South Africa. In British service, it was used with the 5.25 inch and QF 3.7 inch AA guns, as well as the Brakemine missile.

<span class="mw-page-title-main">GL Mk. III radar</span> Family of British radar systems for artillery

Radar, Gun Laying, Mark III, or GL Mk. III for short, was a radar system used by the British Army to directly guide, or lay, anti-aircraft artillery (AA). The GL Mk. III was not a single radar, but a family of related designs that saw constant improvement during and after World War II. These were renamed shortly after their introduction in late 1942, becoming the Radar, AA, No. 3, and often paired with an early warning radar, the AA No. 4, which was also produced in several models.

<span class="mw-page-title-main">Searchlight Control radar</span>

Searchlight Control, SLC for short but nicknamed "Elsie", was a British Army VHF-band radar system that provided aiming guidance to an attached searchlight. By combining a searchlight with a radar, the radar did not have to be particularly accurate, it only had to be good enough to get the searchlight beam on the target. Once the target was lit, normal optical instruments could be used to guide the associated anti-aircraft artillery. This allowed the radar to be much smaller, simpler and less expensive than a system with enough accuracy to directly aim the guns, like the large and complex GL Mk. II radar. In 1943 the system was officially designated Radar, AA, No. 2, although this name is rarely used.

<span class="mw-page-title-main">AMES Type 82</span> Cold War-era British medium-range 3D radar

The AMES Type 82, also widely known by its rainbow codename Orange Yeoman, was an S-band 3D radar built by the Marconi Company and used by the Royal Air Force (RAF), initially for tactical control and later for air traffic control (ATC).

Radar, Anti-Aircraft, or simply AA radar for short, was a classification system for British Army radars introduced in 1943 and used into the 1960s when these systems were replaced by missiles with their own integral radar systems. The classification included subcategories, Number 1 through 8, as well as the many individual systems which were assigned Marks.

<span class="mw-page-title-main">ASV Mark III radar</span>

Radar, Air-to-Surface Vessel, Mark III, or ASV Mk. III for short, was a surface search radar system used by RAF Coastal Command during World War II. It was a slightly modified version of the H2S radar used by RAF Bomber Command, with minor changes to the antenna to make it more useful for the anti-submarine role. It was Coastal Command's primary radar from the spring of 1943 until the end of the war. Several improved versions were introduced, notably the ASV Mark VI, which replaced most Mk. IIIs from 1944 and ASV Mark VII radar, which saw only limited use until the post-war era.

<span class="mw-page-title-main">AN/CPS-1</span>

The AN/CPS-1, also known as the Microwave Early Warning (MEW) radar, was a semi-mobile, S band, early-warning radar developed by the MIT Radiation Laboratory during World War II. It was one of the first projects attempted by the Lab and was intended to build equipment to transition from the British long-wave radar to the new microwave centimeter-band radar made possible by the cavity magnetron. This project, led by Luis Walter Alvarez, became the world's first microwave phased-array antenna.

<span class="mw-page-title-main">M9 gun director</span>

The M9 gun director was an electronic director developed by Bell Labs during World War II. This computer continuously calculated trigonometric firing solutions for anti-aircraft weapons against enemy aircraft. When cued by the SCR-584 centimetric gun-laying radar and used in concert with anti-aircraft guns firing shells with proximity fuzes, it helped form the most effective anti-aircraft weapon system utilized by the Allies during the war.

<span class="mw-page-title-main">SCR-720</span> Type of aircraft radar

The SCR-720 was a World War II aircraft interception radar designed by the Radiation Laboratory (RadLab) at MIT in the United States. It was used by US Army Air Force night fighters as well as the Royal Air Force (RAF) in a slightly modified version known as Radar, Aircraft Interception, Mark X, or AI Mk. X for short.

References

  1. Bennett, S., A history of control engineering: 1930-1955, Peregrinus,1993
  2. Bayliss, L.E., The Development of Unseen H.A.A. Fire Control 1940-45, British National Archives WO 291/303
  3. Robert Buderi, "The Invention that Changed the World", 1996
  4. Bayliss, L.E., The Development of Unseen H.A.A. Fire Control 1940-45, British National Archives WO 291/303
  5. "Lee Davenport Dies at 95; Developed Battlefront Radar", New York Times, 30 September 2011
  6. Baxter, J.P., "Scientists Against Time", p 147, 1947.
  7. Bennett, Stuart, "A History of Control Engineering, 1930-1955"
  8. "The Evolution of Electronic Tracking", W.R. McMurran, NASA0TM-X-70077, 1973
  9. Wurman et al. Design and Development of a Mobile Pencil-Beam Radar, J. of Atmos. Ocean Technology, 1997
  10. Roberts, Sam (11 September 2008). "Figure in Rosenberg Case Admits to Soviet Spying". The New York Times.
  11. Isby, David C (1988). Weapons and tactics of the Soviet Army. Jane's. p. 319. ISBN   0710603525 . Retrieved 14 November 2022.

External references