Temperature-responsive polymer

Last updated

Temperature-responsive polymers or thermoresponsive polymers are polymers that exhibit drastic and discontinuous changes in their physical properties with temperature. [1] The term is commonly used when the property concerned is solubility in a given solvent, but it may also be used when other properties are affected. Thermoresponsive polymers belong to the class of stimuli-responsive materials, in contrast to temperature-sensitive (for short, thermosensitive) materials, which change their properties continuously with environmental conditions. In a stricter sense, thermoresponsive polymers display a miscibility gap in their temperature-composition diagram. Depending on whether the miscibility gap is found at high or low temperatures, either an upper critical solution temperature (UCST) or a lower critical solution temperature (LCST) exists.

Contents

Research mainly focuses on polymers that show thermoresponsivity in aqueous solution. Promising areas of application are tissue engineering, [2] liquid chromatography, [3] [4] drug delivery [2] [5] and bioseparation. [6] Only a few commercial applications exist, for example, cell culture plates coated with an LCST-polymer.

Thermoresponsive behavior of a polymer with LCST; top: coil-to-globule transition in solution; bottom: attached to a surface PNIPAM switch.svg
Thermoresponsive behavior of a polymer with LCST; top: coil-to-globule transition in solution; bottom: attached to a surface

History

The theory of thermoresponsive polymer (similarly, microgels) begins in the 1940s with work from Flory and Huggins who both independently produced similar theoretical expectations for polymer in solution with varying temperature.

The effects of external stimuli on particular polymers were investigated in the 1960s by Heskins and Guillet. [7] They established 32°C as the lower critical solution temperature (LCST) for poly(N-isopropylacrylamide).

Coil-globule transition

Thermoresponsive polymer chains in solution adopt an expanded coil conformation. At the phase separation temperature they collapse to form compact globuli. This process can be observed directly by methods of static and dynamic light scattering. [8] [9] The drop in viscosity can be indirectly observed. When mechanisms which reduce surface tension are absent, the globules aggregate, subsequently causing turbidity and the formation of visible particles.

Phase diagrams of thermoresponsive polymers

The phase separation temperature (and hence, the cloud point) is dependent on polymer concentration. Therefore, temperature-composition diagrams are used to display thermoresponsive behavior over a wide range of concentrations. [10] Phases separate into a polymer-poor and a polymer-rich phase. In strictly binary mixtures the composition of the coexisting phases can be determined by drawing tie-lines. However, since polymers display a molar mass distribution this straightforward approach may be insufficient.

During the process of phase separation the polymer-rich phase can vitrify before equilibrium is reached. This depends on the glass transition temperature for each individual composition. It is convenient to add the glass transition curve to the phase diagram, although it is no real equilibrium. The intersection of the glass transition curve with the cloud point curve is called Berghmans point. [11] In the case of UCST polymers, above the Berghmans point the phases separate into two liquid phases, below this point into a liquid polymer-poor phase and a vitrified polymer-rich phase. For LCST polymers the inverse behavior is observed.

Thermodynamics

Polymers dissolve in a solvent when the Gibbs energy of the system decreases, i.e., the change of Gibbs energy (ΔG) is negative. From the known Legendre transformation of the Gibbs–Helmholtz equation it follows that ΔG is determined by the enthalpy of mixing (ΔH) and entropy of mixing (ΔS).

Without interactions between the compounds there would be no enthalpy of mixing and the entropy of mixing would be ideal. The ideal entropy of mixing of multiple pure compounds is always positive (the term -T∙ΔS is negative) and ΔG would be negative for all compositions, causing complete miscibility. Therefore, the fact that miscibility gaps are observed can only be explained by interaction. In the case of polymer solutions, polymer-polymer, solvent-solvent and polymer-solvent interactions have to be taken into account. A model for the phenomenological description of polymer phase diagrams was developed by Flory and Huggins (see Flory–Huggins solution theory). The resulting equation for the change of Gibbs energy consists of a term for the entropy of mixing for polymers and an interaction parameter that describes the sum of all interactions. [11]

LCST or UCST behavior resulting from the temperature dependence of the interaction parameter Temperature dependence of interaction parameter x.tif
LCST or UCST behavior resulting from the temperature dependence of the interaction parameter

where

A consequence of the Flory-Huggins theory is, for instance, that the UCST (if it exists) increases and shifts into the solvent-rich region when the molar mass of the polymer increases. Whether a polymer shows LCST and/or UCST behavior can be derived from the temperature-dependence of the interaction parameter (see figure). The interaction parameter not only comprises enthalpic contributions but also the non-ideal entropy of mixing, which again consists of many individual contributions (e.g., the strong hydrophobic effect in aqueous solutions). For these reasons, classical Flory-Huggins theory cannot provide much insight into the molecular origin of miscibility gaps.

Applications

Bioseparation

Adhesion of cells on a surface coated with a thermoresponsive polymer. Displayed is a polymer with LCST Cell culture on PNIPAM.svg
Adhesion of cells on a surface coated with a thermoresponsive polymer. Displayed is a polymer with LCST

Thermoresponsive polymers can be functionalized with moieties that bind to specific biomolecules. The polymer-biomolecule conjugate can be precipitated from solution by a small change of temperature. [6] [12] Isolation may be achieved by filtration or centrifugation.

Thermoresponsive surfaces

Tissue engineering

For some polymers it was demonstrated that thermoresponsive behavior can be transferred to surfaces. The surface is either coated with a polymer film or the polymer chains are bound covalently to the surface. This provides a way to control the wetting properties of a surface by small temperature changes. The described behavior can be exploited in tissue engineering since the adhesion of cells is strongly dependent on the hydrophilicity/hydrophobicity. [2] [13] This way, it is possible to detach cells from a cell culture dish by only small changes in temperature, without the need to additionally use enzymes (see figure). Respective commercial products are already available.

Chromatography

Thermoresponsive polymers can be used as the stationary phase in liquid chromatography. [3] Here, the polarity of the stationary phase can be varied by temperature changes, altering the power of separation without changing the column or solvent composition. Thermally related benefits of gas chromatography can now be applied to classes of compounds that are restricted to liquid chromatography due to their thermolability. In place of solvent gradient elution, thermoresponsive polymers allow the use of temperature gradients under purely aqueous isocratic conditions. [14] The versatility of the system is controlled not only by changing temperature, but also by adding modifying moieties that allow for a choice of enhanced hydrophobic interaction, or by introducing the prospect of electrostatic interaction. [15] These developments have already brought major improvements to the fields of hydrophobic interaction chromatography, size exclusion chromatography, ion exchange chromatography, and affinity chromatography separations, as well as pseudo-solid phase extractions ("pseudo" because of phase transitions).

Thermoresponsive gels

Covalently linked gels

Three-dimensional covalently linked polymer networks are insoluble in all solvents, they merely swell in good solvents. [16] [17] Thermoresponsive polymer gels show a discontinuous change of the degree of swelling with temperature. At the volume phase transition temperature (VPTT) the degree of swelling changes drastically. Researchers try to exploit this behavior for temperature-induced drug delivery. In the swollen state, previously incorporated drugs are released easily by diffusion. [18] More sophisticated "catch and release" techniques have been elaborated in combination with lithography [19] and molecular imprinting. [20]

Physical gels

In physical gels unlike covalently linked gels the polymers chains are not covalently linked together. That means that the gel could re-dissolve in a good solvent under some conditions. Thermoresponsive physical gels, also sometimes called thermoresponsive injectable gels have been used in Tissue Engineering. [21] [22] [23] [2] [24] This involves mixing at room temperature the thermoresponsive polymer in solution with the cells and then inject the solution to the body. Due to the temperature increase (to body temperature) the polymer creates a physical gel. Within this physical gel the cells are encapsulated. Tailoring the temperature that the polymer solution gels can be challenging because this depend by many factors like the polymer composition, [25] [26] [27] [28] architecture [25] [26] as well as the molar mass. [27]

Thermoreversible materials

Some thermoreversible gels are used in biomedicine. For instance, hydrogels made of proteins are used as scaffolds in knee replacement. [29] In baking, thermoreversible glazes such as pectin are prized for their ability to set and then reset after melting, [30] and are used in nappage and other processes to ensure a smooth final surface for a presented dish. [31] [32] In manufacturing, thermoplastic elastomers can be set into a shape and then reset to their original shape through thermal reversibility, unlike one-way thermoset elastomers. [33]

Characterization of thermoresponsive polymer solutions

Cloud point

Experimentally, the phase separation can be followed by turbidimetry. There is no universal approach for determining the cloud point suitable for all systems. It is often defined as the temperature at the onset of cloudiness, the temperature at the inflection point of the transmittance curve, or the temperature at a defined transmittance (e.g., 50%). [11] The cloud point can be affected by many structural parameters of the polymer like the hydrophobic content, [25] [26] [27] [28] [34] architecture [25] [26] and even the molar mass. [27] [35]

Hysteresis

The cloud points upon cooling and heating of a thermoresponsive polymer solution do not coincide because the process of equilibration takes time. The temperature interval between the cloud points upon cooling and heating is called hysteresis. The cloud points are dependent on the cooling and heating rates, and hysteresis decreases with lower rates. There are indications that hysteresis is influenced by the temperature, viscosity, glass transition temperature and the ability to form additional intra- and inter-molecular hydrogen bonds in the phase separated state. [36]

Other properties

Another important property for potential applications is the extent of phase separation, represented by the difference in polymer content in the two phases after phase separation. For most applications, phase separation in pure polymer and pure solvent would be desirable although it is practically impossible. The extent of phase separation in a given temperature interval depends on the particular polymer-solvent phase diagram.

Example: From the phase diagram of polystyrene (molar mass 43,600 g/mol) in the solvent cyclohexane it follows that at a total polymer concentration of 10%, cooling from 25 to 20 °C causes phase separation into a polymer-poor phase with 1% polymer and a polymer-rich phase with 30% polymer content. [37]

Also desirable for many applications is a sharp phase transition, which is reflected by a sudden drop in transmittance. The sharpness of the phase transition is related to the extent of phase separation but additionally relies on whether all present polymer chains exhibit the same cloud point. This depends on the polymer endgroups, dispersity, or—in the case of copolymers—varying copolymer compositions. [36] As a result of phase separation, thermoresponsive polymer systems can form well-defined self-assembled nanostructures with a number of different practical application such as in drug and gene delivery, tissue engineering, etc. In order to establish the required properties for applications, a rigorous characterization of the phase separation phenomenon can be carried out by different spectroscopic and calorimetric methods, including nuclear magnetic resonance (NMR) , dynamic light scattering (DLS), small-angle X-ray scattering (SAXS), infrared spectroscopy (IR), Raman spectroscopy, and Differential scanning calorimetry (DSC). [38]

Examples of thermoresponsive polymers

Thermoresponsivity in organic solvents

Due to the low entropy of mixing, miscibility gaps are often observed for polymer solutions. [11] Many polymers are known that show UCST or LCST behavior in organic solvents. [39] Examples for organic polymer solutions with UCST are polystyrene in cyclohexane, [37] [40] polyethylene in diphenylether [41] [42] or polymethylmethacrylate in acetonitrile. [43] An LCST is observed for, e.g., polypropylene in n-hexane, [44] polystyrene in butylacetate [45] or polymethylmethacrylate in 2-propanone. [46]

Thermoresponsivity in water

Polymer solutions that show thermoresponsivity in water are especially important since water as a solvent is cheap, safe and biologically relevant. Current research efforts focus on water-based applications like drug delivery systems, tissue engineering, bioseparation (see the section Applications). Numerous polymers with LCST in water are known. [11] The most studied polymer is poly(N-isopropylacrylamide). [47] [48] [49] Further examples are poly[2-(dimethylamino)ethyl methacrylate] (pDMAEMA) [25] [26] [27] [28] [35] hydroxypropylcellulose, [50] poly(vinylcaprolactam), [51] poly-2-isopropyl-2-oxazoline [52] and polyvinyl methyl ether. [53]

Some industrially relevant polymers show LCST as well as UCST behavior whereas the UCST is found outside the 0-to-100 °C region and can only be observed under extreme experimental conditions. [36] Examples are polyethylene oxide, [54] [55] [56] polyvinylmethylether [57] and polyhydroxyethylmethacrylate. [58] There are also polymers that exhibit UCST behavior between 0 and 100 °C. However, there are large differences concerning the ionic strength at which UCST behavior is detected. Some zwitterionic polymers show UCST behavior in pure water and also in salt-containing water or even at higher salt concentration. [59] [60] [61] [62] By contrast, polyacrylic acid displays UCST behavior solely at high ionic strength. [63] Examples for polymer that show UCST behavior in pure water as well as under physiological conditions are poly(N-acryloylglycinamide), [64] [65] [66] [67] ureido-functionalized polymers, [68] copolymers from N-vinylimidazole and 1-vinyl-2-(hydroxylmethyl)imidazole [69] or copolymers from acrylamide and acrylonitrile. [70] Polymers for which UCST relies on non-ionic interactions are very sensitive to ionic contamination. Small amounts of ionic groups may suppress phase separation in pure water.

The UCST is dependent on the molecular mass of the polymer. For the LCST this is not necessarily the case, as shown for poly(N-isopropylacrylamide). [71] [72] [73]

Schizophrenic behavior of UCST-LCST diblock copolymers

A more complex scenario can be found in the case of diblock copolymers that feature two orthogonally thermo-responsive blocks, i.e., an UCST and an LCST-type block. By applying a temperature stimulus, the individual polymer blocks show different phase transitions, e.g. by increasing the temperature, the UCST-type block features an insoluble-soluble transition, while the LCST-type block undergoes a soluble-insoluble transition. [74] [75] [76] The order of the individual phase transitions depends on the relative positions of the UCST and LCST. Thus, upon temperature change the roles of the soluble and insoluble polymer blocks are reversed and this structural inversion is typically called ‘schizophrenic’ in the literature. [77] [78] [79] Besides the fundamental interest in the mechanism of this behavior, such block copolymers have been proposed for application in smart emulsification, drug delivery, and rheology control. [80] [81] [82] Schizophrenic diblock copolymer have also been applied as thin films for potential use as sensors, smart coatings or nanoswitches, and soft robotics. [83] [84] [85] [86] [59]

Related Research Articles

<span class="mw-page-title-main">Micelle</span> Group of fatty molecules suspended in liquid by soaps and/or detergents

A micelle or micella is an aggregate of surfactant amphipathic lipid molecules dispersed in a liquid, forming a colloidal suspension. A typical micelle in water forms an aggregate with the hydrophilic "head" regions in contact with surrounding solvent, sequestering the hydrophobic single-tail regions in the micelle centre.

<span class="mw-page-title-main">Copolymer</span> Polymer derived from more than one species of monomer

In polymer chemistry, a copolymer is a polymer derived from more than one species of monomer. The polymerization of monomers into copolymers is called copolymerization. Copolymers obtained from the copolymerization of two monomer species are sometimes called bipolymers. Those obtained from three and four monomers are called terpolymers and quaterpolymers, respectively. Copolymers can be characterized by a variety of techniques such as NMR spectroscopy and size-exclusion chromatography to determine the molecular size, weight, properties, and composition of the material.

<span class="mw-page-title-main">Hydrogel</span> Soft water-rich polymer gel

A hydrogel is a biphasic material, a mixture of porous, permeable solids and at least 10% by weight or volume of interstitial fluid composed completely or mainly by water. In hydrogels the porous permeable solid is a water insoluble three dimensional network of natural or synthetic polymers and a fluid, having absorbed a large amount of water or biological fluids. These properties underpin several applications, especially in the biomedical area. Many hydrogels are synthetic, but some are derived from nature. The term 'hydrogel' was coined in 1894.

Poloxamers are nonionic triblock copolymers composed of a central hydrophobic chain of polyoxypropylene flanked by two hydrophilic chains of polyoxyethylene. The word poloxamer was coined by BASF inventor, Irving Schmolka, who received the patent for these materials in 1973. Poloxamers are also known by the trade names Pluronic, Kolliphor, and Synperonic.

Small-angle X-ray scattering (SAXS) is a small-angle scattering technique by which nanoscale density differences in a sample can be quantified. This means that it can determine nanoparticle size distributions, resolve the size and shape of (monodisperse) macromolecules, determine pore sizes, characteristic distances of partially ordered materials, and much more. This is achieved by analyzing the elastic scattering behaviour of X-rays when travelling through the material, recording their scattering at small angles. It belongs to the family of small-angle scattering (SAS) techniques along with small-angle neutron scattering, and is typically done using hard X-rays with a wavelength of 0.07 – 0.2 nm. Depending on the angular range in which a clear scattering signal can be recorded, SAXS is capable of delivering structural information of dimensions between 1 and 100 nm, and of repeat distances in partially ordered systems of up to 150 nm. USAXS can resolve even larger dimensions, as the smaller the recorded angle, the larger the object dimensions that are probed.

<span class="mw-page-title-main">Polyacrylic acid</span> Anionic polyelectrolyte polymer

Poly(acrylic acid) (PAA; trade name Carbomer) is a polymer with the formula (CH2-CHCO2H)n. It is a derivative of acrylic acid (CH2=CHCO2H). In addition to the homopolymers, a variety of copolymers and crosslinked polymers, and partially deprotonated derivatives thereof are known and of commercial value. In a water solution at neutral pH, PAA is an anionic polymer, i.e., many of the side chains of PAA lose their protons and acquire a negative charge. Partially or wholly deprotonated PAAs are polyelectrolytes, with the ability to absorb and retain water and swell to many times their original volume. These properties – acid-base and water-attracting – are the bases of many applications.

Poly(N-isopropylacrylamide) (variously abbreviated PNIPA, PNIPAM, PNIPAAm, NIPA, PNIPAA or PNIPAm) is a temperature-responsive polymer that was first synthesized in the 1950s. It can be synthesized from N-isopropylacrylamide which is commercially available. It is synthesized via free-radical polymerization and is readily functionalized making it useful in a variety of applications.

Pluronic P123 is a symmetric triblock copolymer comprising poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) in an alternating linear fashion, PEO-PPO-PEO. The unique characteristic of PPO block, which is hydrophobic at temperatures above 288 K and is soluble in water at temperatures below 288 K, leads to the formation of micelle consisting of PEO-PPO-PEO triblock copolymers. Some studies report that the hydrophobic core contains PPO block, and a hydrophilic corona consists of PEO block. In 30wt% aqueous solution Pluronic P123 forms a cubic gel phase.

<span class="mw-page-title-main">Lower critical solution temperature</span> Critical temperature below which components of a mixture are miscible for all compositions

The lower critical solution temperature (LCST) or lower consolute temperature is the critical temperature below which the components of a mixture are miscible in all proportions. The word lower indicates that the LCST is a lower bound to a temperature interval of partial miscibility, or miscibility for certain compositions only.

<i>N</i>,<i>N</i>-Methylenebisacrylamide Chemical compound, polyacrylamide crosslinker

N,N′-Methylenebisacrylamide (MBAm or MBAA, colloquially "bis") is the organic compound with the formula CH2[NHC(O)CH=CH2]2. A colorless solid, this compound is a crosslinking agent in polyacrylamides, e.g., as used for SDS-PAGE.

A nanogel is a polymer-based, crosslinked hydrogel particle on the sub-micron scale. These complex networks of polymers present a unique opportunity in the field of drug delivery at the intersection of nanoparticles and hydrogel synthesis. Nanogels can be natural, synthetic, or a combination of the two and have a high degree of tunability in terms of their size, shape, surface functionalization, and degradation mechanisms. Given these inherent characteristics in addition to their biocompatibility and capacity to encapsulate small drugs and molecules, nanogels are a promising strategy to treat disease and dysfunction by serving as delivery vehicles capable of navigating across challenging physiological barriers within the body. 

<span class="mw-page-title-main">Upper critical solution temperature</span> Critical temperature of miscibility in a mixture

The upper critical solution temperature (UCST) or upper consolute temperature is the critical temperature above which the components of a mixture are miscible in all proportions. The word upper indicates that the UCST is an upper bound to a temperature range of partial miscibility, or miscibility for certain compositions only. For example, hexane-nitrobenzene mixtures have a UCST of 19 °C (66 °F), so that these two substances are miscible in all proportions above 19 °C (66 °F) but not at lower temperatures. Examples at higher temperatures are the aniline-water system at 168 °C (334 °F), and the lead-zinc system at 798 °C (1,468 °F).

<span class="mw-page-title-main">Coil–globule transition</span> Collapse of a macromolecule from an expanded coil state to a collapsed globule state

In polymer physics, the coil–globule transition is the collapse of a macromolecule from an expanded coil state through an ideal coil state to a collapsed globule state, or vice versa. The coil–globule transition is of importance in biology due to the presence of coil-globule transitions in biological macromolecules such as proteins and DNA. It is also analogous with the swelling behavior of a crosslinked polymer gel and is thus of interest in biomedical engineering for controlled drug delivery. A particularly prominent example of a polymer possessing a coil-globule transition of interest in this area is that of Poly(N-isopropylacrylamide) (PNIPAAm).

<span class="mw-page-title-main">Poly(methacrylic acid)</span> Chemical compound

Poly(methacrylic acid) (PMAA) is a polymer made from methacrylic acid (preferred IUPAC name, 2-methylprop-2-enoic acid), which is a carboxylic acid. It is often available as its sodium salt, poly(methacrylic acid) sodium salt. The monomer is a viscous liquid with a pungent odour. The first polymeric form of methacrylic acid was described in 1880 by Engelhorn and Fittig. The use of high purity monomers is required for proper polymerization conditions and therefore it is necessary to remove any inhibitors by extraction (phenolic inhibitors) or via distillation. To prevent inhibition by dissolved oxygen, monomers should be carefully degassed prior to the start of the polymerization.

Thermoresponsive polymers can be used as stationary phase in liquid chromatography. Here, the polarity of the stationary phase can be varied by temperature changes, altering the power of separation without changing the column or solvent composition. Thermally related benefits of gas chromatography can now be applied to classes of compounds that are restricted to liquid chromatography due to their thermolability. In place of solvent gradient elution, thermoresponsive polymers allow the use of temperature gradients under purely aqueous isocratic conditions. The versatility of the system is controlled not only through changing temperature, but through the addition of modifying moieties that allow for a choice of enhanced hydrophobic interaction, or by introducing the prospect of electrostatic interaction. These developments have already introduced major improvements to the fields of hydrophobic interaction chromatography, size exclusion chromatography, ion exchange chromatography, and affinity chromatography separations as well as pseudo-solid phase extractions.

Timothy P. Lodge is an American polymer scientist.

Elastin-like polypeptides (ELPs) are synthetic biopolymers with potential applications in the fields of cancer therapy, tissue scaffolding, metal recovery, and protein purification. For cancer therapy, the addition of functional groups to ELPs can enable them to conjugate with cytotoxic drugs. Also, ELPs may be able to function as polymeric scaffolds, which promote tissue regeneration. This capacity of ELPs has been studied particularly in the context of bone growth. ELPs can also be engineered to recognize specific proteins in solution. The ability of ELPs to undergo morphological changes at certain temperatures enables specific proteins that are bound to the ELPs to be separated out from the rest of the solution via experimental techniques such as centrifugation.

Frank Steven Bates is an American chemical engineer and materials scientist. Bates is a Regent's Professor (2007–present), a Distinguished McKnight University Professor (1996–present), and department head (1999-2014) in the department of chemical engineering and materials science at the University of Minnesota, where he has been a faculty member since 1989. Prior to his appointment at the University of Minnesota, Bates was a member of the technical staff at AT&T Bell Laboratories from 1982-1989.

<span class="mw-page-title-main">Polysulfobetaine</span> Dipolar ion polymer

Polysulfobetaines are zwitterionic polymers that contain a positively charged quaternary ammonium and a negatively charged sulfonate group within one constitutional repeat unit. In recent years, polysulfobetaines have received increasing attention owing to their good biotolerance and ultralow-fouling behavior towards surfaces. These properties are mainly referred to a tightly bound hydration layer around each zwitterionic group, which effectively suppresses protein adsorption and thus, improves anti-fouling behavior. Therefore, polysulfobetaines have been typically employed as ultrafiltration membranes, blood-contacting devices, and drug delivery materials.

<span class="mw-page-title-main">Cononsolvency</span>

Cononsolvency is a phenomenon where two solvents that can typically readily dissolve a polymer, when mixed, at certain ratios of these two solvents, are no longer able to dissolve the polymer. This phenomenon is in contrast to cosolvency where two solvents that are both poor at dissolving a material, but when the two poor solvents admixed, can form a mixed solvent capable of dissolving the material.

References

  1. ↑ Hoffman, Allan S. (May 1995). ""Intelligent" Polymers in Medicine and Biotechnology". Artificial Organs . 19 (5): 458–467. doi:10.1111/j.1525-1594.1995.tb02359.x. PMID   7625927.
  2. 1 2 3 4 Ward, Mark A.; Georgiou, Theoni K. (August 3, 2011). "Thermoresponsive Polymers for Biomedical Applications". Polymers . 3 (3): 1215–1242. doi: 10.3390/polym3031215 . hdl: 10044/1/27183 . ISSN   2073-4360.
  3. 1 2 Tan, Irene; Roohi, Farnoosh; Titirici, Maria-Magdalena (October 19, 2011). "Thermoresponsive polymers in liquid chromatography". Analytical Methods . 4 (1): 34–43. doi:10.1039/C1AY05356F. ISSN   1759-9679. Archived from the original on June 21, 2022. Retrieved October 4, 2022.
  4. ↑ Maharjan, Pankaj; Woonton, Brad W.; Bennett, Louise E.; Smithers, Geoffrey W.; DeSilva, Kirthi; Hearn, Milton T. W. (April 1, 2008). "Novel chromatographic separation — The potential of smart polymers". Innovative Food Science & Emerging Technologies . Food Innovation: Emerging Science, Technologies and Applications (FIESTA) Conference. 9 (2). New York: Elsevier Science: 232–242. doi:10.1016/j.ifset.2007.03.028. ISSN   1466-8564.
  5. ↑ Bajpai, A. K.; Shukla, Sandeep K.; Bhanu, Smitha; Kankane, Sanjana (November 2008). "Responsive polymers in controlled drug delivery". Progress in Polymer Science . 33 (11): 1088–1118. doi:10.1016/j.progpolymsci.2008.07.005. ISSN   0079-6700. Archived from the original on July 9, 2022. Retrieved October 4, 2022.
  6. 1 2 Galaev, Igor; Mattiasson, Bo (November 15, 2001). Smart Polymers for Bioseparation and Bioprocessing. Taylor & Francis. ISBN   9781439858165. OCLC   54395177.
  7. ↑ Michael Heskins; James E. Guillet (1968). "Solution Properties of Poly(N-isopropylacrylamide)". J. Macromol. Sci. Chem. 2 (8): 1441–1455. doi:10.1080/10601326808051910.
  8. ↑ Wu, Chi; Wang, Xiaohui (May 4, 1998). "Globule-to-Coil Transition of a Single Homopolymer Chain in Solution". Physical Review Letters. 80 (18): 4092–4094. doi:10.1103/PhysRevLett.80.4092.
  9. ↑ Vshivkov, Sergei A.; Safronov, Alexander P. (November 1997). "The conformational coil-globule transition of polystyrene in cyclohexane solution". Macromolecular Chemistry and Physics. 198 (10): 3015–3023. doi:10.1002/macp.1997.021981003.
  10. ↑ Koningsveld, R. (2001). Polymer Phase Diagrams: A Textbook. W. H. Stockmayer, E. Nies. Oxford, UK: Oxford University Press. ISBN   9780198556350. OCLC   45375807.
  11. 1 2 3 4 5 Aseyev, Vladimir; Tenhu, Heikki; Winnik, Françoise M.; Müller; Borisov, Oleg (2011-09-15). "Non-ionic Thermoresponsive Polymers in Water". Self Organized Nanostructures of Amphiphilic Block Copolymers II (PDF). Berlin, Heidelberg: Springer. pp. 29–89. doi:10.1007/12_2010_57. ISBN   9783642222979. OCLC   756912488. Archived from the original (PDF) on 2022-08-10. Retrieved 2022-10-29. on Google Books. link to original publication.
  12. ↑ Chen, J. P.; Hoffman, A. S. (November 1990). "Polymer-protein conjugates. II. Affinity precipitation separation of human immunogammaglobulin by a poly(N-isopropylacrylamide)-protein A conjugate". Biomaterials. 11 (9): 631–634. doi:10.1016/0142-9612(90)90020-q. ISSN   0142-9612. PMID   2090296.
  13. ↑ Lee, EL.; von Recum, HA (2010). "Cell culture platform with mechanical conditioning and nondamaging cellular detachment". J Biomed Mater Res A. 93 (2): 411–8. doi:10.1002/jbm.a.32754. PMID   20358641.
  14. ↑ Hideko Kanazawa (2007). "Thermally responsive chromatographic materials using functional polymers". J. Sep. Sci. 30 (11): 1646–1656. doi:10.1002/jssc.200700093. PMID   17623446.
  15. ↑ Eri Ayano; Hideko Kanazawa (2006). "Aqueous chromatography system using temperature-responsive polymer-modified stationary phases". J. Sep. Sci. 29 (6): 738–749. doi:10.1002/jssc.200500485. PMID   16830486.
  16. ↑ Patrickios, Costas S.; Georgiou, Theoni K. (March 1, 2003). "Covalent amphiphilic polymer networks". Current Opinion in Colloid & Interface Science. 8 (1): 76–85. doi:10.1016/S1359-0294(03)00005-0.
  17. ↑ Rikkou-Kalourkoti, M.; Patrickios, C. S.; Georgiou, T. K. (January 1, 2012). Möller, Krzysztof MatyjaszewskiMartin (ed.). 6.08 - Model Networks and Functional Conetworks. Amsterdam: Elsevier. pp. 293–308. doi:10.1016/b978-0-444-53349-4.00166-7. ISBN   978-0-08-087862-1.
  18. ↑ Dinarvand, R.; D'Emanuele, A. (October 1, 1995). "The use of thermoresponsive hydrogels for on-off release of molecules". Journal of Controlled Release. 36 (3): 221–227. doi:10.1016/0168-3659(95)00035-7. ISSN   0168-3659.
  19. ↑ Alexandro Castellanos; Samuel J. DuPont; August J. Heim II; Garrett Matthews; Peter G. Stroot; Wilfrido Moreno; Ryan G. Toomey (2007). "Size-Exclusion "capture and release" separations using surface-patterned poly(N-isopropylacrylamide) hydrogels". Langmuir. 23 (11): 6391–6395. doi:10.1021/la700338p. PMID   17441745.
  20. ↑ Roongnapa Suedee; Vatcharee Seechamnanturakit; Bhutorn Canyuk; Chitchamai Ovatlarnporn; Gary P. Martin (2006). "Temperature sensitive dopamine-imprinted (N,N-methylene-bis-acrylamide cross-linked) polymer and its potential application to the selective extraction of adrenergic drugs from urine". J. Chromatogr. A. 1114 (2): 239–249. doi:10.1016/j.chroma.2006.02.033. PMID   16530207.
  21. ↑ Kretlow, James D.; Klouda, Leda; Mikos, Antonios G. (May 30, 2007). "Injectable matrices and scaffolds for drug delivery in tissue engineering". Advanced Drug Delivery Reviews. 59 (4–5): 263–273. doi:10.1016/j.addr.2007.03.013. PMID   17507111.
  22. ↑ Klouda, Leda; Mikos, Antonios G. (January 1, 2008). "Thermoresponsive hydrogels in biomedical applications". European Journal of Pharmaceutics and Biopharmaceutics. Interactive Polymers for Pharmaceutical and Biomedical Applications. 68 (1): 34–45. doi:10.1016/j.ejpb.2007.02.025. PMC   3163097 . PMID   17881200.
  23. ↑ Klouda, Leda (November 1, 2015). "Thermoresponsive hydrogels in biomedical applications: A seven-year update". European Journal of Pharmaceutics and Biopharmaceutics. Polymers for Drug Delivery Systems. 97, Part B (Pt B): 338–349. doi:10.1016/j.ejpb.2015.05.017. PMID   26614556.
  24. ↑ Blacklow, S.; Li, J.; Freedman, B; Zeidi, Mahdi; Chen, C.; Mooney, D.J. (2019). "Bioinspired mechanically active adhesive dressings to accelerate wound closure". Science Advances. 5 (7): eaaw3963. Bibcode:2019SciA....5.3963B. doi: 10.1126/sciadv.aaw3963 . ISSN   2375-2548. PMC   6656537 . PMID   31355332.
  25. 1 2 3 4 5 Ward, Mark A.; Georgiou, Theoni K. (2013). "Multicompartment thermoresponsive gels: does the length of the hydrophobic side group matter?" (PDF). Polymer Chemistry. 4 (6): 1893. doi:10.1039/c2py21032k. Archived (PDF) from the original on March 8, 2022. Retrieved June 19, 2021.
  26. 1 2 3 4 5 Ward, Mark A.; Georgiou, Theoni K. (February 15, 2010). "Thermoresponsive terpolymers based on methacrylate monomers: Effect of architecture and composition". Journal of Polymer Science Part A: Polymer Chemistry. 48 (4): 775–783. Bibcode:2010JPoSA..48..775W. doi:10.1002/pola.23825. ISSN   1099-0518.
  27. 1 2 3 4 5 Ward, Mark A.; Georgiou, Theoni K. (2012). "Thermoresponsive triblock copolymers based on methacrylate monomers: effect of molecular weight and composition". Soft Matter. 8 (9): 2737. Bibcode:2012SMat....8.2737W. doi:10.1039/c2sm06743a.
  28. 1 2 3 Ward, Mark A.; Georgiou, Theoni K. (July 1, 2013). "Thermoresponsive gels based on ABA triblock copolymers: Does the asymmetry matter?". Journal of Polymer Science Part A: Polymer Chemistry. 51 (13): 2850–2859. Bibcode:2013JPoSA..51.2850W. doi:10.1002/pola.26674. ISSN   1099-0518.
  29. ↑ Wei, Wei; Ma, Yuanzhu; Yao, Xudong; Zhou, Wenyan; Wang, Xiaozhao; Li, Chenglin; Lin, Junxin; He, Qiulin; Leptihn, Sebastian; Ouyang, Hongwei (October 10, 2020). "Advanced hydrogels for the repair of cartilage defects and regeneration". Bioactive Materials. 6 (4): 998–1011. doi:10.1016/j.bioactmat.2020.09.030. ISSN   2452-199X. PMC   7557878 . PMID   33102942.
  30. ↑ Pegg, A. M. (January 2012), Baines, David; Seal, Richard (eds.), "8 - The application of natural hydrocolloids to foods and beverages", Natural Food Additives, Ingredients and Flavourings, Woodhead Publishing Series in Food Science, Technology and Nutrition, Woodhead Publishing, pp. 175–196/, ISBN   9781845698119 , retrieved October 25, 2022
  31. ↑ USapplication 2007202225,Chevalier, Olivier,"Cold gelling pastry glaze based on pectin",published 2007-08-30, assigned to Puratos NV, since abandoned.
  32. ↑ Iso, Chef. "Neutral Nappage Glaze for Fruit Tarts". Chef Iso. Retrieved October 25, 2022.
  33. ↑ Gao, Yuan; Liu, Weifeng; Zhu, Shiping (February 8, 2017). "Polyolefin Thermoplastics for Multiple Shape and Reversible Shape Memory". ACS Applied Materials & Interfaces. 9 (5): 4882–4889. doi:10.1021/acsami.6b14728. ISSN   1944-8244. PMID   28092158.
  34. ↑ Raduan, Norsadiah H.; Horozov, Tommy S.; Georgiou, Theoni K. (2010). ""Comb-like" non-ionic polymeric macrosurfactants". Soft Matter. 6 (10): 2321. Bibcode:2010SMat....6.2321R. doi:10.1039/b926822g.
  35. 1 2 Georgiou, Theoni K.; Vamvakaki, Maria; Patrickios, Costas S.; Yamasaki, Edna N.; Phylactou, Leonidas A. (September 10, 2004). "Nanoscopic Cationic Methacrylate Star Homopolymers: Synthesis by Group Transfer Polymerization, Characterization and Evaluation as Transfection Reagents". Biomacromolecules. 5 (6): 2221–2229. doi:10.1021/bm049755e. PMID   15530036.
  36. 1 2 3 Seuring, Jan; Agarwal, Seema (November 23, 2012). "Polymers with Upper Critical Solution Temperature in Aqueous Solution". Macromolecular Rapid Communications . 33 (22): 1898–1920. doi:10.1002/marc.201200433. PMID   22961764.
  37. 1 2 Shultz, A. R.; Flory, P. J. (October 1952). "Phase Equilibria in Polymer—Solvent Systems 1,2" (PDF). Journal of the American Chemical Society. 74 (19): 4760–4767. doi:10.1021/ja01139a010. ISSN   0002-7863. Archived from the original (PDF) on 2022-10-29. link to original publication.
  38. ↑ Velychkivska N, Janisova L, Hill JP, Labuta J (September 2021). "The Battery of Analytical Techniques Necessary for the Effective Characterization of Solutions of Temperature-Sensitive Polymers". Reviews and Advances in Chemistry. 11 (1–2): 100–111. doi:10.1134/S2079978021010076. S2CID   237539482.
  39. ↑ Wohlfarth, Christian; Lide, David R. (2006). "Chapter 13: Upper Critical (UCST) and Lower Critical (LCST) Solution Temperatures of Binary Polymer Solutions". CRC Handbook of Chemistry and Physics, 87th Edition. CRC Taylor & Francis. pp. 19–34. ISBN   9780849304873. OCLC   644855443 . Retrieved 2022-10-29.{{cite book}}: |website= ignored (help) on Google Books.
  40. ↑ Hashizume, J.; Teramoto, A.; Fujita, H. (September 1981). "Phase equilibrium study of the ternary system composed of two monodisperse polystyrenes and cyclohexane". Journal of Polymer Science: Polymer Physics Edition . 19 (9): 1405–1422. doi:10.1002/pol.1981.180190913.
  41. ↑ Nakajima, Akio; Hamada, Fumiyuki; Hayashi, Seiichi (March 8, 2007). "Unperturbed chain dimensions of polyethylene in theta solvents". Journal of Polymer Science Part C: Polymer Symposia . 15 (1): 285–294. doi:10.1002/polc.5070150120.
  42. ↑ Koningsveld, R.; Staverman, A. J. (February 1968). "Liquid–liquid phase separation in multicomponent polymer solutions. III. Cloud-point curves". Journal of Polymer Science Part A-2: Polymer Physics. 6 (2): 349–366. doi:10.1002/pol.1968.160060203.
  43. ↑ Fox, T. G (January 1, 1962). "Properties of dilute polymer solutions III: Intrinsic viscosity/temperature relationships for conventional polymethyl methacrylate". Polymer . 3: 111–128. doi:10.1016/0032-3861(62)90069-1. ISSN   0032-3861.
  44. ↑ Cowie, J. M. G.; McEwen, I. J. (February 1974). "Lower critical solution temperatures of polypropylene solutions". Journal of Polymer Science: Polymer Physics Edition. 12 (2): 441–443. doi:10.1002/pol.1974.180120216.
  45. ↑ Pfohl, Oliver; Hino, Toshiaki; Prausnitz, John M. (May 1, 1995). "Solubilities of styrene-based polymers and copolymers in common solvents". Polymer. 36 (10): 2065–2073. doi:10.1016/0032-3861(95)91454-F. ISSN   0032-3861.
  46. ↑ Cowie, John M. G.; McEwen, Iain J. (January 1976). "Influence of microstructure on the upper and lower critical solution temperatures of poly(methylmethacrylate) solutions". Journal of the Chemical Society, Faraday Transactions 1: Physical Chemistry in Condensed Phases. 72: 526–533. doi:10.1039/F19767200526. ISSN   0300-9599.
  47. ↑ Fujishige, Shouei; Kubota, K.; Ando, I. (April 1989). "Phase transition of aqueous solutions of poly(N-isopropylacrylamide) and poly(N-isopropylmethacrylamide)". The Journal of Physical Chemistry. 93 (8): 3311–3313. doi:10.1021/j100345a085. ISSN   0022-3654.
  48. ↑ Heskins, M.; Guillet, J. E. (December 1, 1968). "Solution Properties of Poly(N-isopropylacrylamide)". Journal of Macromolecular Science: Part A - Chemistry. 2 (8): 1441–1455. doi:10.1080/10601326808051910. ISSN   0022-233X.
  49. ↑ Kubota, Kenji; Fujishige, Shouei; Ando, Isao (January 1990). "Solution Properties of Poly(N-isopropylacrylamide) in Water". Polymer Journal. 22 (1): 15–20. doi: 10.1295/polymj.22.15 . ISSN   1349-0540. S2CID   95411474.
  50. ↑ Kagemoto, A.; Baba, Y. (October 25, 1971). "Study of Liquid-Liquid Phase Equilibrium by Differential Thermal Analysis". High Polymers . 28 (318): 784–788, 821. doi: 10.1295/koron1944.28.784 .
  51. ↑ Maeda, Yasushi; Nakamura, Tomoya; Ikeda, Isao (December 2001). "Hydration and Phase Behavior of Poly(N-vinylcaprolactam) and Poly(N-vinylpyrrolidone) in Water". Macromolecules . 35 (1): 217–222. doi:10.1021/ma011034+. ISSN   0024-9297.
  52. ↑ Amirova, Alina; Rodchenko, Serafim; Kurlykin, Mikhail; Tenkovtsev, Andrey; Krasnou, Illia; Krumme, Andres; Filippov, Alexander (March 2020). "Synthesis and Investigation of Thermo-Induced Gelation of Partially Cross-Linked Poly-2-isopropyl-2-oxazoline in Aqueous Media". Polymers. 12 (3): 698. doi: 10.3390/polym12030698 . PMC   7182854 . PMID   32245164.
  53. ↑ Schild, Howard G.; Tirrell, David A. (May 1, 1990). "Microcalorimetric detection of lower critical solution temperatures in aqueous polymer solutions". The Journal of Physical Chemistry. 94 (10): 4352–4356. doi:10.1021/j100373a088. ISSN   0022-3654.
  54. ↑ Malcolm, G. N.; Rowlinson, J. S. (January 1, 1957). "The thermodynamic properties of aqueous solutions of polyethylene glycol, polypropylene glycol and dioxane". Transactions of the Faraday Society. 53: 921–931. doi:10.1039/TF9575300921. ISSN   0014-7672.
  55. ↑ Saeki, Susumu; Kuwahara, Nobuhiro; Nakata, Mitsuo; Kaneko, Motozo (August 1976). "Upper and lower critical solution temperatures in poly (ethylene glycol) solutions". Polymer. 17 (8): 685–689. doi:10.1016/0032-3861(76)90208-1. ISSN   0032-3861.
  56. ↑ Saeki, Susumu; Kuwahara, Nobuhiro; Nakata, Mitsuo; Kaneko, Motozo (August 1, 1976). "Upper and lower critical solution temperatures in poly (ethylene glycol) solutions". Polymer. 17 (8): 685–689. doi:10.1016/0032-3861(76)90208-1. ISSN   0032-3861.
  57. ↑ Van Assche, Guy; Van Mele, Bruno; Li, Ting; Nies, Erik (February 22, 2011). "Adjacent UCST Phase Behavior in Aqueous Solutions of Poly(vinyl methyl ether): Detection of a Narrow Low Temperature UCST in the Lower Concentration Range". Macromolecules. 44 (4): 993–998. Bibcode:2011MaMol..44..993V. doi:10.1021/ma102572s. ISSN   0024-9297.
  58. ↑ Longenecker, Ryan; Mu, Tingting; Hanna, Mark; Burke, Nicholas A. D.; Stöver, Harald D. H. (November 22, 2011). "Thermally Responsive 2-Hydroxyethyl Methacrylate Polymers: Soluble–Insoluble and Soluble–Insoluble–Soluble Transitions". Macromolecules. 44 (22): 8962–8971. Bibcode:2011MaMol..44.8962L. doi:10.1021/ma201528r. ISSN   0024-9297.
  59. 1 2 Kreuzer, Lucas P.; Widmann, Tobias; Geiger, Christina; Wang, Peixi; Vagias, Apostolos; Heger, Julian E.; Haese, Martin; Hildebrand, Viet; Laschewsky, André; Papadakis, Christine M.; Müller-Buschbaum, Peter (August 3, 2021). "Salt-Dependent Phase Transition Behavior of Doubly Thermoresponsive Poly(sulfobetaine)-Based Diblock Copolymer Thin Films". Langmuir. 37 (30): 9179–9191. doi:10.1021/acs.langmuir.1c01342. ISSN   0743-7463. PMID   34279952. S2CID   236141517. Archived from the original on February 22, 2022. Retrieved February 24, 2022.
  60. ↑ Niebuur, Bart-Jan; Puchmayr, Jonas; Herold, Christian; Kreuzer, Lucas; Hildebrand, Viet; Müller-Buschbaum, Peter; Laschewsky, André; Papadakis, Christine (May 21, 2018). "Polysulfobetaines in Aqueous Solution and in Thin Film Geometry". Materials. 11 (5): 850. Bibcode:2018Mate...11..850N. doi: 10.3390/ma11050850 . ISSN   1996-1944. PMC   5978227 . PMID   29883371.
  61. ↑ Mary, Pascaline; Bendejacq, Denis D.; Labeau, Marie-Pierre; Dupuis, Patrick (July 1, 2007). "Reconciling Low- and High-Salt Solution Behavior of Sulfobetaine Polyzwitterions". The Journal of Physical Chemistry B. 111 (27): 7767–7777. doi:10.1021/jp071995b. ISSN   1520-6106. PMID   17579398.
  62. ↑ Vasantha, Vivek Arjunan; Jana, Satyasankar; Parthiban, Anbanandam; Vancso, Julius G. (2014). "Water swelling, brine soluble imidazole based zwitterionic polymers – synthesis and study of reversible UCST behaviour and gel–sol transitions". Chemical Communications. 50 (1): 46–8. doi:10.1039/C3CC44407D. PMID   23925439.
  63. ↑ Buscall, R.; Corner, T. (January 1, 1982). "The phase-separation behaviour of aqueous solutions of polyacrylic acid and its partial sodium salts in the presence of sodium chloride". European Polymer Journal. 18 (11): 967–974. doi:10.1016/0014-3057(82)90084-2. ISSN   0014-3057.
  64. ↑ Seuring, Jan; Bayer, Frank M.; Huber, Klaus; Agarwal, Seema (January 10, 2012). "Upper Critical Solution Temperature of Poly(N-acryloyl glycinamide) in Water: A Concealed Property". Macromolecules. 45 (1): 374–384. Bibcode:2012MaMol..45..374S. doi:10.1021/ma202059t. ISSN   0024-9297.
  65. ↑ Liu, Fangyao; Seuring, Jan; Agarwal, Seema (December 1, 2012). "Controlled radical polymerization of N -acryloylglycinamide and UCST-type phase transition of the polymers". Journal of Polymer Science Part A: Polymer Chemistry. 50 (23): 4920–4928. doi:10.1002/pola.26322.
  66. ↑ Liu, Fangyao; Seuring, Jan; Agarwal, Seema (December 1, 2012). "Controlled radical polymerization of N -acryloylglycinamide and UCST-type phase transition of the polymers". Journal of Polymer Science Part A: Polymer Chemistry. 50 (23): 4920–4928. Bibcode:2012JPoSA..50.4920L. doi:10.1002/pola.26322.
  67. ↑ Křivánková, Nikola; Kaya, Kerem; Wijngaart, Wouter van der; Edlund, Ulrica (2023-10-04). "Copper-mediated synthesis of temperature-responsive poly(N-acryloyl glycinamide) polymers: a step towards greener and simple polymerisation". RSC Advances. 13 (42). The Royal Society of Chemistry: 29099–29108. doi: 10.1039/D3RA04993K . ISSN   2046-2069.
  68. ↑ Shimada, Naohiko; Ino, Haruka; Maie, Kenji; Nakayama, Miki; Kano, Arihiro; Maruyama, Atsushi (October 10, 2011). "Ureido-Derivatized Polymers Based on Both Poly(allylurea) and Poly( l -citrulline) Exhibit UCST-Type Phase Transition Behavior under Physiologically Relevant Conditions". Biomacromolecules. 12 (10): 3418–3422. doi:10.1021/bm2010752. ISSN   1525-7797. PMID   21928793.
  69. ↑ Meiswinkel, Georg; Ritter, Helmut (June 25, 2013). "A new type of thermoresponsive copolymer with UCST-type transitions in water: poly(N-vinylimidazole-co-1-vinyl-2-(hydroxymethyl)imidazole)". Macromolecular Rapid Communications. 34 (12): 1026–1031. doi:10.1002/marc.201300213. ISSN   1521-3927. PMID   23610054.
  70. ↑ Seuring, Jan; Agarwal, Seema (May 8, 2012). "First Example of a Universal and Cost-Effective Approach: Polymers with Tunable Upper Critical Solution Temperature in Water and Electrolyte Solution". Macromolecules. 45 (9): 3910–3918. Bibcode:2012MaMol..45.3910S. doi:10.1021/ma300355k. ISSN   0024-9297.
  71. ↑ Schäfer-Soenen, H.; Moerkerke, R.; Berghmans, H.; Koningsveld, R.; Dušek, K.; Šolc, K. (February 1, 1997). "Zero and Off-Zero Critical Concentrations in Systems Containing Polydisperse Polymers with Very High Molar Masses. 2. The System Water−Poly(vinyl methyl ether)". Macromolecules. 30 (3): 410–416. doi:10.1021/ma960114o. ISSN   0024-9297.
  72. ↑ Šolc, Karel; Dušek, Karel; Koningsveld, Ronald; Berghmans, Hugo (1995). ""Zero" and "Off-Zero" Critical Concentrations in Solutions of Polydisperse Polymers with Very High Molar Masses". Collection of Czechoslovak Chemical Communications. 60 (10): 1661–1688. doi:10.1135/cccc19951661. ISSN   1212-6950. Archived from the original on October 29, 2022.
  73. ↑ Afroze, F.; Nies, E.; Berghmans, H. (October 1, 2000). "Phase transitions in the system poly( N-isopropylacrylamide)/water and swelling behaviour of the corresponding networks". Journal of Molecular Structure. 554 (1): 55–68. Bibcode:2000JMoSt.554...55A. doi:10.1016/S0022-2860(00)00559-7. ISSN   0022-2860.
  74. ↑ Arotçaréna, Michel; Heise, Bettina; Ishaya, Sultana; Laschewsky, André (April 1, 2002). "Switching the Inside and the Outside of Aggregates of Water-Soluble Block Copolymers with Double Thermoresponsivity". Journal of the American Chemical Society. 124 (14): 3787–3793. doi:10.1021/ja012167d. ISSN   0002-7863. PMID   11929270. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  75. ↑ Virtanen, Janne; Arotçaréna, Michel; Heise, Bettina; Ishaya, Sultana; Laschewsky, André; Tenhu, Heikki (July 1, 2002). "Dissolution and Aggregation of a Poly(NIPA- block -sulfobetaine) Copolymer in Water and Saline Aqueous Solutions". Langmuir. 18 (14): 5360–5365. doi:10.1021/la0118208. ISSN   0743-7463. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  76. ↑ Mertoglu, Murat; Garnier, Sébastien; Laschewsky, André; Skrabania, Katja; Storsberg, Joachim (August 23, 2005). "Stimuli responsive amphiphilic block copolymers for aqueous media synthesised via reversible addition fragmentation chain transfer polymerisation (RAFT)". Polymer. Stimuli Responsive Polymers. 46 (18): 7726–7740. doi:10.1016/j.polymer.2005.03.101. ISSN   0032-3861.
  77. ↑ Canning, Sarah L.; Neal, Thomas J.; Armes, Steven P. (August 22, 2017). "pH-Responsive Schizophrenic Diblock Copolymers Prepared by Polymerization-Induced Self-Assembly". Macromolecules. 50 (16): 6108–6116. Bibcode:2017MaMol..50.6108C. doi:10.1021/acs.macromol.7b01005. ISSN   0024-9297. PMC   5577634 . PMID   28867829.
  78. ↑ Bütün, V.; Liu, S.; Weaver, J. V. M.; Bories-Azeau, X.; Cai, Y.; Armes, S. P. (January 1, 2006). "A brief review of 'schizophrenic' block copolymers". Reactive and Functional Polymers. Special Issue in Honour of John Ebdon. 66 (1): 157–165. doi:10.1016/j.reactfunctpolym.2005.07.021. ISSN   1381-5148.
  79. ↑ Papadakis, Christine M.; Müller-Buschbaum, Peter; Laschewsky, André (July 30, 2019). "Switch It Inside-Out: "Schizophrenic" Behavior of All Thermoresponsive UCST–LCST Diblock Copolymers". Langmuir. 35 (30): 9660–9676. doi:10.1021/acs.langmuir.9b01444. ISSN   0743-7463. PMID   31314540. S2CID   197541963. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  80. ↑ Kotsuchibashi, Yohei; Ebara, Mitsuhiro; Aoyagi, Takao; Narain, Ravin (October 27, 2016). "Recent Advances in Dual Temperature Responsive Block Copolymers and Their Potential as Biomedical Applications". Polymers. 8 (11): 380. doi: 10.3390/polym8110380 . ISSN   2073-4360. PMC   6431892 . PMID   30974657.
  81. ↑ Ranka, Mikhil; Katepalli, Hari; Blankschtein, Daniel; Hatton, T. Alan (November 21, 2017). "Schizophrenic Diblock-Copolymer-Functionalized Nanoparticles as Temperature-Responsive Pickering Emulsifiers". Langmuir. 33 (46): 13326–13331. doi:10.1021/acs.langmuir.7b03008. ISSN   0743-7463. PMID   29064711. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  82. ↑ Cummings, Chad; Murata, Hironobu; Koepsel, Richard; Russell, Alan J. (March 10, 2014). "Dramatically Increased pH and Temperature Stability of Chymotrypsin Using Dual Block Polymer-Based Protein Engineering". Biomacromolecules. 15 (3): 763–771. doi:10.1021/bm401575k. ISSN   1525-7797. PMID   24506329. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  83. ↑ Kreuzer, Lucas P.; Widmann, Tobias; Bießmann, Lorenz; Hohn, Nuri; Pantle, Johannes; Märkl, Raphael; Moulin, Jean-François; Hildebrand, Viet; Laschewsky, André; Papadakis, Christine M.; Müller-Buschbaum, Peter (April 28, 2020). "Phase Transition Kinetics of Doubly Thermoresponsive Poly(sulfobetaine)-Based Diblock Copolymer Thin Films". Macromolecules. 53 (8): 2841–2855. Bibcode:2020MaMol..53.2841K. doi:10.1021/acs.macromol.0c00046. ISSN   0024-9297. S2CID   216346530. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  84. ↑ Kreuzer, Lucas P.; Widmann, Tobias; Hohn, Nuri; Wang, Kun; Bießmann, Lorenz; Peis, Leander; Moulin, Jean-Francois; Hildebrand, Viet; Laschewsky, André; Papadakis, Christine M.; Müller-Buschbaum, Peter (May 14, 2019). "Swelling and Exchange Behavior of Poly(sulfobetaine)-Based Block Copolymer Thin Films". Macromolecules. 52 (9): 3486–3498. Bibcode:2019MaMol..52.3486K. doi:10.1021/acs.macromol.9b00443. ISSN   0024-9297. S2CID   155174181. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  85. ↑ Kreuzer, Lucas P.; Widmann, Tobias; Aldosari, Nawarah; Bießmann, Lorenz; Mangiapia, Gaetano; Hildebrand, Viet; Laschewsky, André; Papadakis, Christine M.; Müller-Buschbaum, Peter (October 27, 2020). "Cyclic Water Storage Behavior of Doubly Thermoresponsive Poly(sulfobetaine)-Based Diblock Copolymer Thin Films". Macromolecules. 53 (20): 9108–9121. Bibcode:2020MaMol..53.9108K. doi:10.1021/acs.macromol.0c01335. ISSN   0024-9297. S2CID   226323489. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
  86. ↑ Kreuzer, Lucas P.; Geiger, Christina; Widmann, Tobias; Wang, Peixi; Cubitt, Robert; Hildebrand, Viet; Laschewsky, André; Papadakis, Christine M.; Müller-Buschbaum, Peter (August 10, 2021). "Solvation Behavior of Poly(sulfobetaine)-Based Diblock Copolymer Thin Films in Mixed Water/Methanol Vapors". Macromolecules. 54 (15): 7147–7159. Bibcode:2021MaMol..54.7147K. doi:10.1021/acs.macromol.1c01179. ISSN   0024-9297. S2CID   237724968. Archived from the original on February 24, 2022. Retrieved February 24, 2022.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.