WiMedia Alliance

Last updated
WiMedia Alliance
Successor UWB Alliance
Formation2002
Dissolved2010
Formerly called
Wireless Multimedia Alliance

The WiMedia Alliance was a non-profit industry trade group that promoted the adoption, regulation, standardization and multi-vendor interoperability of ultra-wideband (UWB) technologies.[ citation needed ] It existed from about 2002 through 2009.[ citation needed ]

Contents

History

The Wireless Multimedia Alliance was founded by 2002. [1]

The WiMedia Alliance developed reference technical specifications including:

The WiMedia ultra-wideband (UWB) common radio platform incorporated MAC layer and PHY layer specifications based on multi-band orthogonal frequency-division multiplexing (MB-OFDM). It was intended for short-range multimedia file transfers at data rates of 480 Mbit/s and beyond with low power consumption, and operates in the 3.1 to 10.6 GHz UWB spectrum. WiMedia UWB was promoted for personal computers, consumer electronics, mobile devices and automotive networks. WiMedia Alliance and MultiBand OFDM Alliance Special Interest Group (MBOA-SIG, promoted by Intel) merged into a single organization in 2005. The merged group operated as the WiMedia Alliance. [2]

The ultra-wideband system provided a wireless personal area network (WPAN) with data payload communication capabilities of 53.3, 55, 80, 106.67, 110, 160, 200, 320, 480, 640, 800, 960, and 1024 Mbit/s. The WiMedia UWB platform was complementary to WPAN technologies such as Bluetooth 3.0, Certified Wireless USB, the 1394 Trade Group’s “Wireless FireWire” Protocol Adaptation Layer (PAL) (Non-IP Peer to Peer architecture) and Wireless TCP/IP - Digital Living Network Alliance. Different wireless protocols can operate within the same wireless personal area network without interference. In addition to these, many other industry protocols can reside on top of the WiMedia UWB platform. Those include Ethernet, Digital Visual Interface (DVI) and High-Definition Multimedia Interface (HDMI). The WiMedia PHY specification has an over-the-air uncoded capability of more than 1024 Mbit/s; the specification was promoted to support wireless video, operating at multiple Gbit/s data rates.

The WiMedia Network (formerly WiNET) is a protocol adaptation layer that builds on the WiMedia UWB common radio platform to augment the convergence platform with TCP/IP services.

Certified Wireless USB can operate in two ways:

Bluetooth, Wireless 1394, IP (WiMedia Network) operate on top of Wimedia UWB PHY - Wimedia UWB MAC - Convergence Layer like Coexistence Wireless USB.

Within the WiMedia MAC specification is the MAC Convergence Architecture (WiMCA) that allows applications to share UWB resources. WiMCA defines a number of policies, including channel-time utilization; secure association, authentication and data transfer; device and WPAN management; quality of service; discovery of services; and power management.

Board members of the alliance included Alereon, CSR plc, Olympus Corporation, Samsung and Wisair.

By early 2006, implementations were delayed by standardization issues. [3] On March 16, 2009, the WiMedia Alliance announced technology transfer agreements for WiMedia ultra-wideband (UWB) specifications. WiMedia transferred all specifications, including work on future high speed and power optimized implementations, to the Bluetooth Special Interest Group (SIG), Wireless USB Promoter Group and the USB Implementers Forum. [4] After the technology transfer, marketing and related administrative items, the WiMedia Alliance ceased operations in 2010. [5] [6] [7] [8] [9]

UWB Alliance

On December 19, 2018, the UWB Alliance was officially launched to promote the adoption, regulation, standardization and multi-vendor interoperability of ultra-wideband (UWB) technologies. The founding members include: Hyundai, Kia, Zebra, Decawave, Alteros, Novelda, and Ubisense. [10] [11]

Standardization

IEEE

IEEE 802.15.3a was an attempt to provide a higher speed UWB PHY enhancement amendment to IEEE 802.15.3 for applications which involve imaging and multimedia.

The attempt to create an Institute of Electrical and Electronics Engineers (IEEE) ultra-wideband standard failed because of several factors.

First, based on execution of the approved IEEE 802.15.3a Task Group down selection procedure, there were only two proposals remaining. Each of the remaining proposals contained mutually exclusive communication architectures. Neither proposer's radio could communicate with the other. One proposal was a merger of a novel OFDM architecture proposed by Texas Instruments and eventually adopted by the majority of the industry, by the USB-IF for Wireless USB and by the Bluetooth SIG for high speed Bluetooth. This merged proposal became known as the MB-OFDM proposal and was sponsored by Texas Instruments as a member of the Multi Band OFDM Alliance, which is now part of WiMedia. The other proposal was a merger between an original direct sequence pulse based design (DS-UWB) contributed by Xtreme Spectrum and DecaWave that was modified to include features of several other pulse based proposals. Ironically, after the dust settled through several years of each proposer bashing the other's technical implementation, both remaining proposals achieved nearly identical theoretical performance in terms of data throughput, channel robustness, overall design DC power consumption, and device cost. Not until actual WiMedia devices entered the market was shown that WiMedia's proposal and implementation did not come close to living up to its advertised specification of 480 Mbit/s.

Second, there were numerous attempts by each proposer to achieve both victory in the down selection vote, and then reach the 75% approval rating required for task group confirmation of the selected technical proposal, which never happened. In the first round of down selection, the MB-OFDM proposal was selected. Through several subsequent rounds of down selection, the selected proposal alternated between MB-OFDM and DS-UWB, with neither being able to achieve technical confirmation.

There were several attempts to create a compromise solution, the most notable was a proposal that would have allowed the MB-OFDM and DS-UWB radios to communicate with each other and share spectrum. Based on a concept called the Common Signaling Mode (CSM) it specified supporting a lower data rate than the minimum mandatory 110 Mbit/s, for purposes of spectrum coordination and allowing other elements necessary for proper operation of a wireless personal area network. The Common Signaling Mode (CSM) was proposed by John Santhoff of Pulse~LINK as a way forward for both competing proposals that would allow complete coexistence and at least minimal interoperability. Companies supporting the MB-OFDM proposal insisted that a common signaling mode was not needed or technically feasible and that their customer research supported a strict notion that only one physical layer (PHY) would be tolerated by the consumer market. Thus, even though the DS-UWB supporters embraced CSM as a bridge between the two proposals, the lack of acceptance by MB-OFDM supporters killed what turned out to be the best solution to achieve a compromise between the proposers. It's interesting to note that the concept of a Common Signaling Mode (CSM) was later adopted by IEEE 802.15.3c for the 60 GHz PHY layer and renamed Common Mode Signaling to solve the same two PHY problem.

The contest became so contentious that the originally elected Task Group Chair, Bob Heile, who was also the 802.15 Working Group [12] Chair, resigned his position. Bob Heile was replaced by Jim Lansford, CTO of Alereon, and Gregg Rasor, Director of Ultrawideband Research and Development in Motorola Labs, who co-chaired IEEE 802.15.3a until its end. The idea of co-chairs was brought about in yet another attempt to forge a compromise that would generate an IEEE standard for ultrawideband.

Consequently, in the Spring of 2006, the IEEE 802.15.3a Task Group was officially disbanded by the IEEE Standards Association. On January 19, 2006, IEEE 802.15.3a task group (TG3a) [13] members voted to recommend that the IEEE 802 Executive Committee ask NESCOM [14] to withdraw the December 2002 project authorization request (PAR), [15] which initiated the development of a high data rate UWB PHY amendment for the IEEE 802.15.3 WPAN standard.

The most commendable achievement of IEEE 802.15.3a was its consolidation of 23 UWB PHY specifications into two proposals using: Multi-Band Orthogonal Frequency Division Multiplexing (MB-OFDM) UWB, supported by the WiMedia Alliance, then adopted by the USB-IF for Wireless USB and by the Bluetooth SIG for high speed Bluetooth, while the Direct Sequence - UWB (DS-UWB) approach, supported by the UWB Forum, was abandoned.

ECMA

In December 2008, Ecma International released specification (ECMA-368 and ECMA-369) for UWB technology based on the WiMedia Ultra-Wideband (UWB) Common Radio Platform. [16] [17]

ETSI

ECMA-368 is also a European Telecommunications Standards Institute (ETSI) standard, ETSI TS 102 455).

ISO

The Ecma 368 and 369 standards were approved as ISO/IEC standards in 2007 respectively with numbers:

See also

Related Research Articles

IEEE 802.15 is a working group of the Institute of Electrical and Electronics Engineers (IEEE) IEEE 802 standards committee which specifies Wireless Specialty Networks (WSN) standards. The working group was formerly known as Working Group for Wireless Personal Area Networks.

<span class="mw-page-title-main">IEEE 802.11</span> Wireless network standard

IEEE 802.11 is part of the IEEE 802 set of local area network (LAN) technical standards, and specifies the set of media access control (MAC) and physical layer (PHY) protocols for implementing wireless local area network (WLAN) computer communication. The standard and amendments provide the basis for wireless network products using the Wi-Fi brand and are the world's most widely used wireless computer networking standards. IEEE 802.11 is used in most home and office networks to allow laptops, printers, smartphones, and other devices to communicate with each other and access the Internet without connecting wires. IEEE 802.11 is also a basis for vehicle-based communication networks with IEEE 802.11p.

<span class="mw-page-title-main">Personal area network</span> Short distance computer network

A personal area network (PAN) is a computer network for interconnecting electronic devices within an individual person's workspace. A PAN provides data transmission among devices such as computers, smartphones, tablets and personal digital assistants. PANs can be used for communication among the personal devices themselves, or for connecting to a higher level network and the Internet where one master device takes up the role as gateway.

Ultra-wideband is a radio technology that can use a very low energy level for short-range, high-bandwidth communications over a large portion of the radio spectrum. UWB has traditional applications in non-cooperative radar imaging. Most recent applications target sensor data collection, precise locating, and tracking. UWB support started to appear in high-end smartphones in 2019.

<span class="mw-page-title-main">IEEE 802.20</span>

IEEE 802.20 or Mobile Broadband Wireless Access (MBWA) was a specification by the standard association of the Institute of Electrical and Electronics Engineers (IEEE) for mobile broadband networks. The main standard was published in 2008. MBWA is no longer being actively developed.

IEEE 802.15.4 is a technical standard which defines the operation of a low-rate wireless personal area network (LR-WPAN). It specifies the physical layer and media access control for LR-WPANs, and is maintained by the IEEE 802.15 working group, which defined the standard in 2003. It is the basis for the Zigbee, ISA100.11a, WirelessHART, MiWi, 6LoWPAN, Thread, Matter and SNAP specifications, each of which further extends the standard by developing the upper layers which are not defined in IEEE 802.15.4. In particular, 6LoWPAN defines a binding for the IPv6 version of the Internet Protocol (IP) over WPANs, and is itself used by upper layers like Thread.

<span class="mw-page-title-main">Wireless USB</span> Wireless radio communication protocol

Wireless USB (Universal Serial Bus) was a short-range, high-bandwidth wireless radio communication protocol created by the Wireless USB Promoter Group which intended to increase the availability of general USB-based technologies. It was unrelated to Wi-Fi, and different from the Cypress WirelessUSB offerings. It was maintained by the WiMedia Alliance which ceased operations in 2009. Wireless USB is sometimes abbreviated as "WUSB", although the USB Implementers Forum discouraged this practice and instead prefers to call the technology Certified Wireless USB to distinguish it from the competing UWB standard.

IEEE 802.11n-2009, or 802.11n, is a wireless-networking standard that uses multiple antennas to increase data rates. The Wi-Fi Alliance has also retroactively labelled the technology for the standard as Wi-Fi 4. It standardized support for multiple-input multiple-output, frame aggregation, and security improvements, among other features, and can be used in the 2.4 GHz or 5 GHz frequency bands.

<span class="mw-page-title-main">UWB Forum</span>

The UWB Forum was an industry organization promoting interoperable ultra-wideband (UWB) wireless computer networking products from multiple vendors. It was founded in 2004 and disbanded around 2006.

FM-UWB is a modulation scheme using double FM: low-modulation index digital FSK followed by high-modulation index analog FM to create a constant envelope UWB signal. FDMA techniques at the subcarrier level may be exploited to accommodate multiple users. The system is intended for low and medium bit rate, and short-range WPAN systems. The technology, developed at CSEM, is paving the way for true low-power LDR-UWB communication devices. FM-UWB is an optional mode in the IEEE802.15.6 Body Area Network (BAN) standard.

A wide variety of different wireless data technologies exist, some in direct competition with one another, others designed for specific applications. Wireless technologies can be evaluated by a variety of different metrics of which some are described in this entry.

IEEE 802.11a-1999 or 802.11a was an amendment to the IEEE 802.11 wireless local network specifications that defined requirements for an orthogonal frequency-division multiplexing (OFDM) communication system. It was originally designed to support wireless communication in the unlicensed national information infrastructure (U-NII) bands as regulated in the United States by the Code of Federal Regulations, Title 47, Section 15.407.

IEEE 802.11b-1999 or 802.11b is an amendment to the IEEE 802.11 wireless networking specification that extends throughout up to 11 Mbit/s using the same 2.4 GHz band. A related amendment was incorporated into the IEEE 802.11-2007 standard.

IEEE 802.11g-2003 or 802.11g is an amendment to the IEEE 802.11 specification that operates in the 2.4 GHz microwave band. The standard has extended link rate to up to 54 Mbit/s using the same 20 MHz bandwidth as 802.11b uses to achieve 11 Mbit/s. This specification under the marketing name of Wi-Fi has been implemented all over the world. The 802.11g protocol is now Clause 19 of the published IEEE 802.11-2007 standard, and Clause 19 of the published IEEE 802.11-2012 standard.

<span class="mw-page-title-main">Chirp spread spectrum</span>

In digital communications, chirp spread spectrum (CSS) is a spread spectrum technique that uses wideband linear frequency modulated chirp pulses to encode information. A chirp is a sinusoidal signal whose frequency increases or decreases over time.

IEEE 802.15.4a was an amendment to IEEE 802.15.4-2006 specifying that additional physical layers (PHYs) be added to the original standard. It has been merged into and is superseded by IEEE 802.15.4-2011.

WiGig, alternatively known as 60 GHz Wi-Fi, refers to a set of 60 GHz wireless network protocols. It includes the current IEEE 802.11ad standard and also the IEEE 802.11ay standard.

IEEE 802.11ac-2013 or 802.11ac is a wireless networking standard in the IEEE 802.11 set of protocols, providing high-throughput wireless local area networks (WLANs) on the 5 GHz band. The standard has been retroactively labelled as Wi-Fi 5 by Wi-Fi Alliance.

Joseph C. Decuir is an American fellow of the Institute of Electrical and Electronics Engineers (IEEE) who was nominated in 2015 for contributions to computer graphics and video games.

References

  1. "Welcome to the new home of the Wireless Multimedia Alliance". Archived from the original on April 26, 2002. Retrieved August 30, 2013.
  2. Peter Judge (March 8, 2005). "UWB's fate to be decided this week". ARN. Retrieved August 30, 2013.
  3. Peter Judge (July 31, 2006). "End is nigh for Freescale's UWB?". ARN. Retrieved August 30, 2013.
  4. Patrick Mannion (March 16, 2009). "WiMedia folds, UWB spec goes to Bluetooth, USB groups". EE Times. Archived from the original on February 9, 2011. Retrieved August 30, 2013.
  5. "Type Approval". Technographik. January 4, 2010. Retrieved 2010-09-04.[ permanent dead link ]
  6. "Wimedia.org FAQ". Archived from the original on March 23, 2009. Retrieved 2010-09-04.
  7. Bluetooth.com [ dead link ]
  8. "USB.org". USB.org. 2009-03-16. Archived from the original on 2011-06-10. Retrieved 2010-09-04.
  9. "Incisor.tv". Incisor.tv. 2009-03-16. Retrieved 2010-09-04.
  10. "Press Releases: UWB Alliance to Lead Industry Growth and Drive Global Standards". UWB Alliance. Retrieved 2019-09-18.
  11. "UWB Alliance to focus on interoperability, further boosting the UWB ecosystem". FierceWireless. 20 December 2018. Retrieved 2019-09-18.
  12. IEEE 802.15 Working Group website
  13. IEEE 802.15.3a Task Group website
  14. IEEE-SA Standards Board - New Standards Committee (NESCOM)
  15. IEEE 802.15.3a Project Authorization Request
  16. "Standard ECMA-368: High Rate Ultra Wideband PHY and MAC Standard". Ecma International. December 2008.
  17. "Standard ECMA-369: MAC-PHY Interface for ECMA-368". Ecma International. December 2008.