LNER Class K4

Last updated

LNER Class K4
61994 The Great Marquess in Blaenau Ffestiniog.jpg
The Great Marquess at Blaenau Ffestiniog, Wales
Type and origin
Power typeSteam
Designer Nigel Gresley
Builder Darlington Works
Build date1937-1939
Total produced6
Specifications
Configuration:
   Whyte 2-6-0
Gauge 4 ft 8+12 in (1,435 mm) standard gauge
Driver dia.5 ft 2 in (1.575 m)
Loco weight68.4 long tons (69.5 t; 76.6 short tons)
Tender weight44.2 long tons (44.9 t; 49.5 short tons)
Fuel type Coal
Boiler pressure200 psi (1.38 MPa)
Cylinders Three
Cylinder size 18.5 in × 26 in (470 mm × 660 mm)
Performance figures
Tractive effort 36,600 lbf (162.80 kN)
Career
Power class5P6F
Numbers
  • LNER (Pre 1946): 3441-3446
  • LNER (Post 1946) 1993-1998
  • BR: 61993-61998
Withdrawn1961
DispositionOne preserved, remainder scrapped

The London and North Eastern Railway (LNER) Class K4 is a class of 2-6-0 steam locomotives designed by Nigel Gresley for the steep grades of the West Highland Line.

Contents

West Highland Line challenge

The North British Railway (NBR) West Highland line to Mallaig via Fort William, presented a combined triple operating challenge of: steep gradients; severe curves; and restrictive axle loading limits. Having used D34 'Glen' 4-4-0s, increased loads led to regular double-heading. Locomotive engineers proposed use of LNER Class K3, but they would not have been permitted to operate between Fort William and Mallaig.

Having proposed a new design based on a K3 boiler, in October 1924 a loan was made of a single LNER Class K2, which provided the required increase in power and adhesion. As K3s replaced K2 on the network, more K2s were loaned to the line, with the loan becoming permanent from October 1925.

With further increases in load and needs for additional traffic speed, in September 1934 Gresley instructed Doncaster Works to investigate the possibility of increasing the tractive effort of the K2s. After recommending against a design which increased boiler pressure 220 psi (1.52 MPa) and cylinder diameter to 21 inches (533 mm), in 1935 the Joint Traffic & Locomotive Committee signed off provision of a new design by reducing the 1936 build of K3s from 21 to 20.

The eventual May 1936 design was based on the 1924 proposal for a 2-6-0 with 5 ft 2 in (1.575 m) diameter coupled wheels, but with K3 cylinders, a K2 boiler, and a B17 firebox. The frame was 5 inches (127 mm) longer than the K3, with a design boiler pressure of 180 psi (1.24 MPa) giving a tractive effort of 32,939 lbf (146.5 kN), and an estimated factor of adhesion of 3.92.

Prototype

The prototype K4 No.3441 left Darlington for Eastfield depot, Glasgow on 28 January 1937. After five weeks of crew training and being confined to goods work it made its début on a passenger train on 4 March. It soon became apparent that the 180 psi (1.24 MPa) boiler pressure brought little improvement in average speeds over the existing K2, and that No.3441 responded sluggishly when up against the gradients of the West Highland line. Gresley reacted by raising the steam pressure to 200 psi (1.38 MPa) which saw the tractive effort leap to 36,598 lbf (162.8 kN), with a corresponding reduction in the factor of adhesion to 3.54. The K4 could now demonstrate its true capabilities handling 300 ton trains and with maximum speeds around 60 mph (97 km/h) on level ground.[ citation needed ] An advantage of the newcomer was that it used only marginally more coal in working 300 ton trains than the K2s did with considerably lighter loads.

The successful trials with No. 3441 led to five more being built. Apart from the prototype Loch Long all were named after Highland chieftains and grandees.

Operations

K4 61996 "Lord of the Isles" at Stirling railway station on a train for Oban in September 1958 LNER K4 2-6-0 61996 Stirling 03.09.58.jpg
K4 61996 "Lord of the Isles" at Stirling railway station on a train for Oban in September 1958

The K4s quickly endeared themselves to the Scottish crews and, apart from some heavily loaded summer trains, eliminated uneconomic double-heading over the West Highland. However, as with all Gresley 2-6-0s it could be a rough ride at speed, and a locomotive designed to climb was not suited to the flat straight stretches of the line into Glasgow Queen Street railway station, or the 8.5 miles stretch alongside Loch Eil. Ride induced vibration was a problem on these stretches, and the middle big-end bearing would require regular nut tightening, with the middle connecting rod dropping off on one occasion: this resulted in increased maintenance inspections.

Crews began to prefer the LNER Class V4, but their lower power restricted their use and the K4s retained their pre-eminence on the West Highland line until the 1947 arrival of the first B1 4-6-0s, which replaced the K4s from Glasgow to Fort William. These were followed after nationalisation by an influx of Stanier 5MT 4-6-0s and the new K1s, that left the K4s increasingly confined to goods workings.

During the 1950s, the K4s' sphere of operation enlarged and they began to appear at locations such as Edinburgh, Perth, Forfar, Ayr and Tweedmouth. In 1959 all were concentrated at Thornton in Junction depot in Fife and all were withdrawn in October 1961.

Numbering

LNER NumberBritish Railways
Number
NameBuild Date
at Darlington
WithdrawnNotes
344161993 Loch Long January 1937October 1961Scrapped
3442 61994 The Great Marquess July 1938December 1961Preserved, owned by John Cameron
344361995 Cameron Of Lochiel December 1938October 1961Scrapped
344461996 Lord Of The Isles December 1938October 1961Scrapped
344561997 MacCailin Mor January 1939December 1945 (rebuilt) 1962Rebuilt as Thompson K1/1
344661998 MacLeod of MacLeod January 1939October 1961Scrapped

In 1945 Edward Thompson rebuilt 3445 MacCailin Mor into the first LNER Thompson Class K1. LNER 1946 numbers 1993–6/8 and BR numbers 61993–6/8.

Preservation

LNER Class K4 class 2-6-0 steam locomotive No. 61994 The Great Marquess stands at Loughborough during the Great Central Railway's Steam Gala January 2011. This was the engine's final outing on the railway before returning to Scotland. Great marquess gcr.jpg
LNER Class K4 class 2-6-0 steam locomotive No. 61994 The Great Marquess stands at Loughborough during the Great Central Railway's Steam Gala January 2011. This was the engine's final outing on the railway before returning to Scotland.

One of the six strong class has survived into preservation, following the efforts of the late Viscount Garnock, who purchased No. 61994 The Great Marquess from British Rail (BR) and had the engine overhauled to working order. Based at Leeds No. 3442 undertook railtour work until forced into retirement by the ban imposed on steam working by BR in 1968. From 1972 No. 3442 was stored on the Severn Valley Railway (SVR) until 1980 when it was overhauled. In the mid 2000s, No. 3442 was bought by John Cameron and the locomotive left the SVR for overhaul at Crewe.

Following the completion of its overhaul at Crewe it was returned to service on the mainline, alongside visiting heritage railways around the UK. During its mainline career, it has visited many places that none of the K4's visited during their working careers for the LNER and BR. Places it has visited in recent years include: Carlisle, Barrow Hill, Redmire, York, Manchester, Whitby & Blaenau Ffestiniog. It even proved popular working railtours up the "Conwy Valley line" from Llandudno Junction to Blaenau Ffestiniog, the routes gradient being 1 in 47 heading towards Blaenau. [1]

61994 is now retired and on public display in the Museum of Scottish Railways, Bo'ness, where it is receiving cosmetic restoration by a small team of dedicated SRPS volunteers. The eventual plan will be for the owner, The Cameron Railway Trust, to house the locomotive in a museum to be built on John's Balbuthie farm, along with 60009 "Union of South Africa". However, planning permission for the construction of Johns museum has yet to be granted by Fife Council.

Sources

  1. https://www.youtube.com/watch?v=rP9RqcIvKv4 61994 Working "The Welsh Mountaineer" to Blaenau Ffestiniog in August 2012

Related Research Articles

<span class="mw-page-title-main">LNER Class A4</span> Class of streamlined 4-6-2 pacific locomotive designed by Sir Nigel Gresley

The LNER Class A4 is a class of streamlined 4-6-2 steam locomotive designed by Nigel Gresley for the London and North Eastern Railway in 1935. Their streamlined design gave them high-speed capability as well as making them instantly recognisable, and one of the class, 4468 Mallard, holds the world record as the fastest steam locomotive. Thirty-five of the class were built to haul express passenger trains on the East Coast Main Line route from London Kings Cross via York to Newcastle, and later via Newcastle to Edinburgh, Scotland. They remained in service on the East Coast Main Line until the early 1960s when they were replaced by Deltic diesel locomotives; they themselves proving to be worthy successors to the A4s. Several A4s saw out their remaining days until 1966 in Scotland, particularly on the Aberdeen – Glasgow express trains, for which they were used to improve the timing from 3.5 to 3 hours.

LNER Class A4 4498 <i>Sir Nigel Gresley</i> Preserved LNER Class A4 locomotive

LNER Class A4 4498 Sir Nigel Gresley is a preserved British steam locomotive built by Doncaster Works for the London & North Eastern Railway in 1937.

<span class="mw-page-title-main">LNER Thompson Class B1</span>

The London and North Eastern Railway (LNER) Thompson Class B1 is a class of steam locomotive designed by Edward Thompson for medium mixed traffic work.

<span class="mw-page-title-main">GNR Class C1 (small boiler)</span>

The Great Northern Railway (GNR) Small Boiler Class C1 is a class of steam locomotive, the first 4-4-2 or Atlantic type in Great Britain. They were designed by Henry Ivatt in 1897. In total 22 were built between 1898 and 1903 at Doncaster Works. The class were commonly known as 'Klondykes' [sic], after the 1897 Klondike gold rush. They could reach speeds of up to 90 mph. They were also known as Small Atlantics.

<span class="mw-page-title-main">LNER Gresley Classes A1 and A3</span> Class of 4-6-2 pacific locomotive designed by Sir Nigel Gresley

The London and North Eastern Railway LNER Gresley Classes A1 and A3 locomotives represented two distinct stages in the history of the British 4-6-2 "Pacific" steam locomotives designed by Nigel Gresley. They were designed for main line passenger services and later express passenger services, initially on the Great Northern Railway (GNR), a constituent company of the London and North Eastern Railway after the amalgamation of 1923, for which they became a standard design. The change in class designation to A3 reflected the fitting to the same chassis of a higher pressure boiler with a greater superheating surface and a small reduction in cylinder diameter, leading to an increase in locomotive weight. Eventually all of the A1 locomotives were rebuilt, most to A3 specifications, but no. 4470 was completely rebuilt as Class A1/1.

<span class="mw-page-title-main">Tasmanian Government Railways K class</span> Class of 2 Garratt locomotives

The Tasmanian Government Railways K class was a class of 0-4-0+0-4-0 Garratt locomotives operated by the Tasmanian Government Railways from 1909 – the first Garratt locomotives built.

<span class="mw-page-title-main">Darlington Works</span> Railway Engineering Works

Darlington Works was established in 1863 by the Stockton and Darlington Railway in the town of Darlington in the north east of England. The main part of the works, the North Road Shops was located on the northeast side of the Stockton and Darlington Railway

<span class="mw-page-title-main">LNER Peppercorn Class A2</span>

The London and North Eastern Railway (LNER) Peppercorn Class A2 is a class of steam locomotive designed for express passenger work by Arthur Peppercorn, the chief designer of the LNER after Edward Thompson. All save the first of the 15 built were constructed under British Railways after nationalisation in 1948. Only one example is preserved.

<span class="mw-page-title-main">LNER Class J38</span>

The London and North Eastern Railway Class J38 was a class of steam locomotive designed for freight transport. They were designed by Nigel Gresley and introduced in 1926. A total of 35 were built at the LNER's Darlington Works in 1926 and they were used in Scotland. All passed into British Railways ownership in 1948 and they were renumbered from 5900–5934 to 65900–65934.

Arthur Henry Peppercorn, was an English railway engineer, and was the last Chief Mechanical Engineer (CME) of the London and North Eastern Railway.

<span class="mw-page-title-main">NER Class S3</span>

The North Eastern Railway Class S3, classified B16 by the LNER, was a class of 4-6-0 steam locomotive designed for mixed traffic work. It was designed by Vincent Raven and introduced in 1920. The earlier members of this class were fitted with Westinghouse Brakes - all of this equipment was removed during the 1930s.

<span class="mw-page-title-main">LNER Class P1</span>

The London and North Eastern Railway Class P1 Mineral 2-8-2 Mikado was a class of two steam locomotives designed by Nigel Gresley. They were two of the most powerful freight locomotives ever designed for a British railway. It was initially intended they be a more powerful 2-10-0 version of the earlier Class O2 2-8-0s. The design was submitted in August 1923, for use between Peterborough and London, and also between Immingham and Wath marshalling yard. The power was quoted as being 25% more than the O2.

<span class="mw-page-title-main">LNER Class A2</span>

The first London and North Eastern Railway (LNER) Class A2 was a class of 4-6-2 steam locomotive designed by Vincent Raven for the North Eastern Railway. Two were built by the NER in 1922 before the grouping and another three by the LNER in 1924. Their LNER numbers were 2400–2404. All five locomotives were named by the LNER.

<span class="mw-page-title-main">LNER Thompson/Peppercorn Class K1</span>

The London and North Eastern Railway (LNER) Class K1 is a type of 2-6-0 (mogul) steam locomotive designed by Edward Thompson. Thompson preferred a simple two-cylinder design instead of his predecessor Nigel Gresley's three-cylinder one. The seventy K1s were intended to be split between the North Eastern Region of British Railways and the Eastern Region of British Railways.

<span class="mw-page-title-main">LNER Class V4</span>

The London and North Eastern Railway Class V4 was a class of 2-6-2 steam locomotive designed by Sir Nigel Gresley for mixed-traffic use. It was Gresley's last design for the LNER before he died in 1941. The V4s had similarities in their appearance and mechanical layout to the V2 "Green Arrow" class. The V2s, introduced some years before, were large and heavy locomotives, with very limited route availability. The V4 was a lightweight alternative, suitable for use over the whole of the LNER network.

<span class="mw-page-title-main">LNER Class V1/V3</span> C20 classes of 2-6-2T British steam locomotives

The London and North Eastern Railway (LNER) Class V1 and Class V3 were two classes of related 2-6-2T steam locomotive designed by Sir Nigel Gresley. A total of 82 V1s were built with 71 being rebuilt into the higher pressure V3s with an additional ten being built as V3s from the final batch of V1s. The V3 was a development of the V1 with increased boiler pressure and a resultant increase in tractive effort.

<span class="mw-page-title-main">LNER Thompson Class A2/1</span>

The London and North Eastern Railway (LNER) Thompson Class A2/1 was a class of 4-6-2 steam locomotives built at Darlington locomotive works during 1944. They were originally ordered as Class V2 locomotives, as designed by Sir Nigel Gresley, but were revised during construction into a 4-6-2 'Pacific' arrangement under the instruction of Edward Thompson.

<span class="mw-page-title-main">NBR S class</span>

The NBR S Class was a class of 0-6-0 steam locomotive designed by William Paton Reid for freight work on the North British Railway. The engines were initially designated as B class, being a development of the standard B class locomotives designed by Reid some eight years previously, and represented the culmination of a long evolution on the NBR of powerful 0-6-0 freight engines. The new locomotives were introduced in 1914 and had superheaters, inside cylinders and piston valves operated by Stephenson valve gear.

<span class="mw-page-title-main">NER Class R1</span>

The NER Class R1 was a class of 4-4-0 steam locomotives of the North Eastern Railway. The class was designed by Wilson Worsdell and built from 1908 to 1909.

LNER Gresley K4 61994 <i>The Great Marquess</i>

LNER 3442 The Great Marquess is a member of the London and North Eastern Railway (LNER) Class K4 designed by Nigel Gresley for the steep grades of the West Highland Line. It was renumbered 1994 in the LNER's 1946 renumbering scheme, and then renumbered 61994 by British railways after the 1948 nationalisation of Britain's railways.