The American National Standards Institute is a private non-profit organization that oversees the development of voluntary consensus standards for products, services, processes, systems, and personnel in the United States. The organization also coordinates U.S. standards with international standards so that American products can be used worldwide.
ASTM International, formerly known as American Society for Testing and Materials, is an international standards organization that develops and publishes voluntary consensus technical standards for a wide range of materials, products, systems, and services. Some 12,575 ASTM voluntary consensus standards operate globally. The organization's headquarters is in West Conshohocken, Pennsylvania, about 5 mi (8.0 km) northwest of Philadelphia.
Sound Transmission Class is an integer rating of how well a building partition attenuates airborne sound. In the US, it is widely used to rate interior partitions, ceilings, floors, doors, windows and exterior wall configurations. Outside the US, the Sound Reduction Index (SRI) ISO index is used. The STC rating very roughly reflects the decibel reduction of noise that a partition can provide. The STC is useful for evaluating annoyance due to speech sounds, but not music or machinery noise as these sources contain more low frequency energy than speech.
A fire door is a door with a fire-resistance rating used as part of a passive fire protection system to reduce the spread of fire and smoke between separate compartments of a structure and to enable safe egress from a building or structure or ship. In North American building codes, it, along with fire dampers, is often referred to as a closure, which can be derated compared against the fire separation that contains it, provided that this barrier is not a firewall or an occupancy separation. In Europe national standards for fire doors have been harmonised with the introduction of the new standard EN 16034, which refers to fire doors as fire-resisting door sets. Starting September 2016, a common CE marking procedure was available abolishing trade barriers within the European Union for these types of products. In the UK, it is Part B of the Building Regulations that sets out the minimum requirements for the fire protection that must be implemented in all dwellings this includes the use of fire doors. All fire doors must be installed with the appropriate fire resistant fittings, such as the frame and door hardware, for it to fully comply with any fire regulations.
Tempered or toughened glass is a type of safety glass processed by controlled thermal or chemical treatments to increase its strength compared with normal glass. Tempering puts the outer surfaces into compression and the interior into tension. Such stresses cause the glass, when broken, to shatter into small granular chunks instead of splintering into jagged shards as ordinary annealed glass does. The granular chunks are less likely to cause injury.
ASTM C1270 is a Standard Practice for Detection Sensitivity Mapping of In-Plant Walk-Through Metal Detectors. This standard was created by the American Standard for Testing and Materials (ASTM) and published in December 1997. ASTM International which was founded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard deals with a procedure to establish the weakest detection path through the portal aperture and the worst-case orthogonal orientation of metallic test objects. This practice is considered to develop the assistance about operators of walk-through metal detectors with meeting the metal detection performance requirements of the responsible regulatory authority.
ASTM C1349 is a Standard Specification for Architectural Flat Glass Clad Polycarbonate. This specification was created by the American Society for Testing and Materials (ASTM). Founded in 1898, ASTM International is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This specification deals with the quality requirements for cut sizes of glass clad polycarbonate (GCP). Polycarbonate is becoming more common in house wares as well as laboratories and in industry, especially in applications where any of its main features — high impact resistance, temperature resistance, optical properties—are required. In this regards, polycarbonate is useful regarding security, detention, hurricane/cyclic wind-resistant, and blast and ballistic-resistant glazing applications.
ASTM F1450 is a standard test method for hollow metal swinging door assemblies for detention facilities. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was founded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33, a committee which specializes in detention and correctional facilities. This method dealt with requirements for test to determine the performance characteristics of swinging detention hollow metal door assemblies of various styles and types of construction. The aim is to test the capability to prevent intrusion, avoid unauthorized access and to resist common types of vandalism in an organization. In this regards, ASTM has simulated repeated exertion of tremendous amounts of impact energy against a door in order to break through.
ASTM F1577 is a standard test method for swinging doors with locks created by ASTM International. This standard was published by ASTM F33, which is a committee that specializes in developing standards for detention and correctional facilities. F33 has published 14 standards in this area. F1577 deals with the equipment, procedures, and acceptance conditions for determining the normal operational performance and the performance characteristics under several conditions of locks used in swinging door assemblies in organizations such as detention and correctional institutions. Several features are not considered, such as installation and maintenance conditions.
ASTM F1592 is a Standard Test Method for Detention Hollow Metal Vision Systems.
ASTM F1643 is a Standard Test Methods for Detention Sliding Door Locking Device Assembly. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33 which is a committee specializes about detention and correctional facilities. FM 33 has published 14 standards in this area. The test enables to give information about the performance feature regarding devices in services against assault, smoke, and fire conditions into several organizations including detention and correctional institutions. Several features are not considered such as both installation and maintenance conditions. This test enables to help ensure that detention sliding devices perform against intrusion, avoid that intruders penetrate in unauthorized access and to resist common types of vandalism into an organization.
ASTM F1915 is a standard test method for glazing for detention facilities. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33 which is a committee specializes about detention and correctional facilities. FM 33 has published 14 standards in this area. This standard deals with the equipment, procedures, and acceptance conditions for determining the normal operational performance and the performance characteristics under several conditions of glazing for detention facilities into several organizations including detention and correctional institutions. Several features are not considered such as both installation and maintenance conditions. This test enables to help ensure that glazing used for windows and doors perform against intrusion, avoid that intruders penetrate in unauthorized access and to resist common types of vandalism into an organisation.
ASTM F2248 is a standard practice for specifying an equivalent 3-Second Duration design loading for blast resistant glazing fabricated with laminated glass. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was founded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F14 which is a committee specializes about on systems products and services. The standard explain different methods to check the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration
ASTM F2322 is a standard test method for physical assault on vertical fixed barriers for detention and correctional facilities. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33 which is a committee specializes about detention and correctional facilities. FM 33 has published 14 standards in this area. This test enables to help ensure that physical assault on vertical fixed barriers perform against intrusion, avoid that intruders penetrate in unauthorized access and to resist common types of vandalism into an organization.
ASTM F2348 is a standard test performance specification for privacy padlocks. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F12.50 which is a committee specializes about locking devices. The standards deal with requirement regarding security for padlocks. This standard involves descriptions, operational tests, forcing tests, and surreptitious entry tests.
ASTM F571 is a standard practice for installation of exit devices in security areas. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F12.50 which is a committee specializes about locking devices. This standard practice deals with information regarding the installation of exit devices used in areas of security in order to reach the more great security level without violating the requirements of NFPA 101. NFPA is the National Fire Protection Association. In this paper NFPA 101, the NFPA introduce a code writing process and its performance-based activities.
ASTM F626 is a standard specification for fence fittings.
ASTM F883 is a standard performance specification for padlocks.
A technical standard is an established norm or requirement for a repeatable technical task which is applied to a common and repeated use of rules, conditions, guidelines or characteristics for products or related processes and production methods, and related management systems practices. A technical standard includes definition of terms; classification of components; delineation of procedures; specification of dimensions, materials, performance, designs, or operations; measurement of quality and quantity in describing materials, processes, products, systems, services, or practices; test methods and sampling procedures; or descriptions of fit and measurements of size or strength.
The term Fenestration Testing Laboratory refers to either an individual test facility or the collective group of independent testing laboratories that have been inspected and accredited by nationally and internationally recognized governing bodies to perform fenestration test standards.