The National Electrical Code (NEC), or NFPA 70, is a regionally adoptable standard for the safe installation of electrical wiring and equipment in the United States. It is part of the National Fire Code series published by the National Fire Protection Association (NFPA), a private trade association. Despite the use of the term "national", it is not a federal law. It is typically adopted by states and municipalities in an effort to standardize their enforcement of safe electrical practices. In some cases, the NEC is amended, altered and may even be rejected in lieu of regional regulations as voted on by local governing bodies.
The National Fire Protection Association (NFPA) is an international nonprofit organization devoted to eliminating death, injury, property and economic loss due to fire, electrical and related hazards. As of 2018, the NFPA claims to have 50,000 members and 9,000 volunteers working with the organization through its 250 technical committees.
ASTM International, formerly known as American Society for Testing and Materials, is an international standards organization that develops and publishes voluntary consensus technical standards for a wide range of materials, products, systems, and services. Some 12,575 ASTM voluntary consensus standards operate globally. The organization's headquarters is in West Conshohocken, Pennsylvania, about 5 mi (8.0 km) northwest of Philadelphia.
The International Building Code (IBC) is a model building code developed by the International Code Council (ICC). It has been adopted for use as a base code standard by most jurisdictions in the United States. The IBC addresses both health and safety concerns for buildings based upon prescriptive and performance related requirements. The IBC is fully compatible with all other published ICC codes. The code provisions are intended to protect public health and safety while avoiding both unnecessary costs and preferential treatment of specific materials or methods of construction. However, a 2019 New York Times story revealed a secret agreement with the National Association of Home Builders that allowed the industry group, which represents the construction industry, to limit improvements in the code that would make buildings more environmentally sustainable and resistant to natural disasters, prompting a congressional investigation. The ICC, in response to a Congressional inquiry, vehemently denied the characterization of the agreement, noting, "While home builders are among [our code development] partners, they do not have disproportionate control of the Code Council’s model code development process. On the contrary, volunteer government officials with experience and expertise exercise by far the most control in the process."
NFPA 70E, titled Standard for Electrical Safety in the Workplace, is a standard of the National Fire Protection Association (NFPA). The document covers electrical safety requirements for employees. The NFPA is best known for publishing the National Electrical Code.
ASTM C1270 is a Standard Practice for Detection Sensitivity Mapping of In-Plant Walk-Through Metal Detectors. This standard was created by the American Standard for Testing and Materials (ASTM) and published in December 1997. ASTM International which was founded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard deals with a procedure to establish the weakest detection path through the portal aperture and the worst-case orthogonal orientation of metallic test objects. This practice is considered to develop the assistance about operators of walk-through metal detectors with meeting the metal detection performance requirements of the responsible regulatory authority.
ASTM E2395 is a Standard Specification for Voluntary Security Performance of Window and Door Assemblies with and without Glazing Impact. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. Through this standard is specified voluntary performance test for the resistance to forced entry of window and door assemblies. This standards deal with the capability of window and door assemblies to prevent entry about intruders. These requirements are only limited to window and door assemblies
ASTM F1450 is a standard test method for hollow metal swinging door assemblies for detention facilities. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was founded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33, a committee which specializes in detention and correctional facilities. This method dealt with requirements for test to determine the performance characteristics of swinging detention hollow metal door assemblies of various styles and types of construction. The aim is to test the capability to prevent intrusion, avoid unauthorized access and to resist common types of vandalism in an organization. In this regards, ASTM has simulated repeated exertion of tremendous amounts of impact energy against a door in order to break through.
ASTM F1577 is a standard test method for swinging doors with locks created by ASTM International. This standard was published by ASTM F33, which is a committee that specializes in developing standards for detention and correctional facilities. F33 has published 14 standards in this area. F1577 deals with the equipment, procedures, and acceptance conditions for determining the normal operational performance and the performance characteristics under several conditions of locks used in swinging door assemblies in organizations such as detention and correctional institutions. Several features are not considered, such as installation and maintenance conditions.
ASTM F1592 is a Standard Test Method for Detention Hollow Metal Vision Systems.
ASTM F1643 is a Standard Test Methods for Detention Sliding Door Locking Device Assembly. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33 which is a committee specializes about detention and correctional facilities. FM 33 has published 14 standards in this area. The test enables to give information about the performance feature regarding devices in services against assault, smoke, and fire conditions into several organizations including detention and correctional institutions. Several features are not considered such as both installation and maintenance conditions. This test enables to help ensure that detention sliding devices perform against intrusion, avoid that intruders penetrate in unauthorized access and to resist common types of vandalism into an organization.
ASTM F1712 is a standard specification for steel chain-link fencing materials used for high security applications. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was founded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This was published by ASTM F14 which is a committee specializes about high security fences and perimeter barriers.
ASTM F1915 is a standard test method for glazing for detention facilities. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33 which is a committee specializes about detention and correctional facilities. FM 33 has published 14 standards in this area. This standard deals with the equipment, procedures, and acceptance conditions for determining the normal operational performance and the performance characteristics under several conditions of glazing for detention facilities into several organizations including detention and correctional institutions. Several features are not considered such as both installation and maintenance conditions. This test enables to help ensure that glazing used for windows and doors perform against intrusion, avoid that intruders penetrate in unauthorized access and to resist common types of vandalism into an organisation.
ASTM F2248 is a standard practice for specifying an equivalent 3-Second Duration design loading for blast resistant glazing fabricated with laminated glass. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was founded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F14 which is a committee specializes about on systems products and services. The standard explain different methods to check the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration
ASTM F2322 is a standard test method for physical assault on vertical fixed barriers for detention and correctional facilities. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F33 which is a committee specializes about detention and correctional facilities. FM 33 has published 14 standards in this area. This test enables to help ensure that physical assault on vertical fixed barriers perform against intrusion, avoid that intruders penetrate in unauthorized access and to resist common types of vandalism into an organization.
ASTM F2348 is a standard test performance specification for privacy padlocks. This standard was created by the American Standard for Testing and Materials (ASTM). ASTM International which was funded in 1898, is an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. This standard was published by ASTM F12.50 which is a committee specializes about locking devices. The standards deal with requirement regarding security for padlocks. This standard involves descriptions, operational tests, forcing tests, and surreptitious entry tests.
ASTM F626 is a standard specification for fence fittings.
ASTM F883 is a standard performance specification for padlocks.
Flame spread or surface burning characteristics rating is a ranking derived by laboratory standard test methodology of a material's propensity to burn rapidly and spread flames. There are several standardized methods of determining flame spread,
