Action threads

Last updated

In firearms, action threads refer to the screw threads used to attach a barrel to a receiver, most commonly used in rifles and revolvers, but also on some pistols and shotguns. The threads on the receiver are often called receiver action threads and are usually internal threads, with the matching threads on the barrel being called barrel action threads and are usually external threads. This method of fixing a barrel to a receiver has been used extensively by firearms manufacturers since before the 20th century,[ citation needed ] and can be viewed as a traditional barrel mounting method.

Contents

Action threads are not the only method of fixing a barrel to a receiver (see Alternative methods below). Furthermore, some firearm designs have moving instead of fixed barrels (e.g. most recoil operated pistols or the Barrett M82 rifle).

Action threads must not be confused with muzzle threads, which are used on the other end of the barrel for mounting accessories such as a flash hider, suppressor or muzzle brake (compensator).

Designation

There are many systems for designating thread types (metric, unified, Whitworth, etc.). Threading can be specified by diameter, pitch, angle, length and fit tolerances. However, the use of action threads is not well standardized within the firearms industry, and threading can vary between manufacturers and models.

For example, factory and aftermarket receivers using the Remington 700 footprint are produced with various types of action threads, all with a 26.99 mm (1 1⁄16 in) diameter, but with a pitch of either a 1.588 mm (16 TPI, Remington standard), 1.411 mm (18 TPI) or 1.270 mm (20 TPI, Savage standard). [1]

Typically, many rifles use thread diameters in the range between 25–27 mm (0.98–1.06 in).[ citation needed ] Many older rifles from the first half of the 20th century use a thread pitch around 2 mm (12.7 TPI), while many modern rifle use thread pitches around 1.5 mm (16.93 TPI). Fine threaded systems intended for hand tightening typically use thread pitches around 1 mm (25.4 TPI).[ citation needed ]

Mounting

Using action threads to mount a barrel to a receiver typically requires fitting by a competent gunsmith, and typically some machining has to be done.

In this process it is important so set the correct headspace. [2] Correct mounting is important both for safety and accuracy. [3] If the barrel, receiver and bolt are not fitted properly, severe and potential fatal problems can arise due to faulty headspace, e.g. cartridge overpressure and case rupture. Threaded barrels are often mounted to the receiver with a lot of torque, and will therefore generally require tools for assembly and disassembly, such as a suitable action wrench and a vise. Depending on the firearm, a recoil lug is sometimes fitted between the barrel and stock as part of the process,

Cleaning up the receiver and barrel action threads is often done during "blueprinting" in order to increase accuracy. [4]

Alternative methods

Several alternative mounting methods to using action threads exist.

Barrel press fit

Pressing the barrel into the receiver to achieve a press fit is an alternative to using action threads which has been used on firearms such as Anschütz Fortner, Anschütz Model 54, [5] AKM [6] and Sauer 101. [7] [8]

Barrel nut

Attaching the barrel the receiver using a barrel nut and a barrel with a shoulder us an alternative to action threads which has been used in firearms such as the Sten gun and AR-15.

Hand tools

Quick barrel change systems is an increasingly popular alternative, as seen in for example SIG Sauer 200 STR, Roessler Titan or Blaser R8. These methods typically only require simple hand tools (like a hex key) or no tools at all. This can be an great advantage to competition shooters who regularly wear out barrels, or for hunters who want a modular rifle that can shoot several calibers. In these designs, the bolt locks directly into the barrel, and the manufacturer often guarantees that the barrel is headspaced correctly from the factory.

See also

Related Research Articles

Single-shot

Single-shot firearms are firearms that hold only a single round of ammunition, and must be reloaded after each shot. The history of firearms began with single-shot designs, and many centuries passed before multi-shot repeater designs became commonplace. Single-shot designs are less complex than revolvers or magazine-fed firearms, and many single-shot designs are still produced by many manufacturers, in both cartridge- and non-cartridge varieties, from zip guns to the highest-quality shooting-match weapons.

Bolt action Type of firearm mechanism

Bolt action is a type of manual firearm action that is operated by directly manipulating the bolt via a bolt handle, which is most commonly placed on the right-hand side of the weapon.

Action (firearms)

In firearms terminology, an action is the functional mechanism of a breech-loading weapon that handles the ammunition cartridges, or the method by which that mechanism works. Actions are technically not present on muzzleloaders, as all those are single-shot weapons with a closed off breech and the ammunition is manually loaded through the muzzle. Instead, the muzzleloader ignition mechanism is referred to as the lock.

Colt AR-15 Type of Semi-automatic rifle

The Colt AR-15 is a lightweight, magazine-fed, gas-operated semi-automatic rifle. The "AR” stands for the first two letters of ArmaLite. It was designed with the extensive use of aluminum alloys and synthetic materials in order to reduce weight. Colt's Manufacturing Company currently uses the AR-15 trademark for its line of semi-automatic AR-15 rifles.

The Accuracy International Arctic Warfare rifle is a bolt-action sniper rifle designed and manufactured by the British company Accuracy International. It has proved popular as a civilian, police, and military rifle since its introduction in the 1980s. The rifles have some features that improve performance in very cold conditions without impairing operation in less extreme conditions.

The Sauer 202 is a lightweight bolt-action rifle manufactured by Sauer & Sohn in Germany between 1993 and 2015. The rifle was imported to the US by SIG Arms. This rifle has a modular construction which allowed easy replacement of components and caliber changes. This rifle has a modular barrel-change system allows to change between calibers easily, and was offered in a large selection of calibers.

A rim is an external flange that is machined, cast, molded, stamped, or pressed around the bottom of a firearms cartridge. Thus, rimmed cartridges are sometimes called "flanged" cartridges. Almost all cartridges feature an extractor or headspacing rim, in spite of the fact that some cartridges are known as "rimless cartridges". The rim may serve a number of purposes, including providing a lip for the extractor to engage, and sometimes serving to headspace the cartridge.

The Remington 788 is a bolt-action, centerfire rifle that was made by Remington Arms from 1967 to 1983. It was marketed as an inexpensive yet accurate hunting rifle to compete with other gun companies' less expensive rifles alongside their more expensive Model 700 line. The 788 utilizes a single-column detachable magazine holding 3 rounds. A .22 rimfire model was also produced known as the 580, 581, or 582 depending on its method of feed. A target version of the .22 caliber 58x series, the 540X, was used by the US military as a training rifle and later disposed through the Civilian Marksmanship Program.

Robinson Armament XCR Type of Assault rifle (XCR-L Series)Battle rifle (XCR-M Series)

The Robinson Armament Co. XCR is a multi-caliber, gas piston weapon system developed by Robinson Armament Co. for U.S. Special Operations Command (SOCOM) to satisfy the requirements of the SOF Combat Assault Rifle, or SCAR competition, but was disqualified on a technicality due to late delivery of blank firing adapters. Robinson Armament continued development and the XCR is now being offered to law enforcement, the military and general public. Deliveries of the rifle began in mid-2006. The XCR was displayed to U.S. Army officials during an invitation-only Industry Day on November 13, 2008. The goal of the Industry Day was to review current carbine technology prior to writing formal requirements for a future replacement for the M4 Carbine.

Barrett REC7 Type of Carbine, Semi-automatic rifle

The Barrett REC7 is an American firearm manufactured as a selective-fire fully-automatic and semi-automatic rifle by Barrett Firearms. It is an M4 carbine utilizing a short-stroke gas piston system. REC7 is available in either 5.56×45mm NATO or 6.8mm Remington SPC. The REC7 is Barrett’s second AR-pattern rifle chambered for the 6.8mm Remington SPC cartridge, the first being the Barrett M468 rifle. The 6.8 SPC-chambered M468 rifle employed the same direct gas-impingement system as the M4.

The Sako TRG is a bolt-action sniper rifle line designed and manufactured by the Finnish firearms manufacturer, SAKO of Riihimäki. The TRG-21 and TRG-22 are designed to fire standard .308 Winchester sized cartridges, while the TRG-41 and TRG-42 are designed to fire more powerful and dimensionally larger .300 Winchester Magnum (7.62×67mm) and .338 Lapua Magnum (8.6×70mm) cartridges. They are available with olive drab green, desert tan/coyote brown, dark earth or black stocks, and are also available with a folding stock.

The Remington Model 30 is a US sporting rifle of the inter-war period based on the military P14/M1917 Enfield rifle action, which was manufactured for the British and US governments during World War I. Initial specimens used surplus military parts with some modifications in order to consume the stock of parts, though further modifications were made as production progressed and later rifles were produced from newly manufactured parts. Most early rifles were in the military .30-06 calibre used in the M1917 but it became available in a variety of chamberings. It was the first high-powered bolt-action sporting rifle produced by Remington.

The CZ-550 is a bolt-action hunting rifle series manufactured by Česká zbrojovka Uherský Brod. The CZ 550 series is available with a medium or magnum sized action. The CZ 550 rifle resembles the Mauser 98 rifle series, though it is not an exact copy.

The SIG Sauer 200 STR, also known as the SIG Sauer 200 STR Match, is a bolt action rifle mostly used as a target/competition rifle for national competitions by Norwegian, Swedish and Danish sport shooters. It is a variant of the Sauer 200 TR or SIG Sauer 200 TR Match rifle that features thicker 19 mm (0.75 in) diameter barrels. The 200 STR is produced by J. P. Sauer & Sohn GmbH in Germany.

The Weatherby Mark V is a centerfire, bolt-action rifle manufactured by Weatherby of Sheridan, Wyoming. The rifle was introduced in 1957 by Weatherby and was designed to safely contain the high pressures associated with the Weatherby line of high performance cartridges. It is the flagship rifle of the Weatherby line of firearms.

Anschütz 1827 Fortner Type of biathlon rifle

Anschütz 1827 Fortner is a straight-pull action biathlon rifle designed by Peter Fortner junior and produced in cooperation with J. G. Anschütz. The rifle has been dominant in the sport of biathlon since the late 1980s, and is the current sport standard. It is estimated to be used by that 97% of biathlon competitors worldwide. About 7000 had been manufactured by 2007.

Husqvarna 1900, later Carl Gustaf 1900, is a bolt action rifle developed in Sweden in the 1960s by Husqvarna Vapenfabrik, which also produced the rifle from 1967 to 1970. The rifle was produced in the variants Standard, Monte Carlo, Monte Carlo Lux and a sport model, and got a reputation for having a very high quality. In 1970 the department producing the rifle was sold to Förenade Fabriksverken (FFV), and the production was moved to Carl Gustafs Gevärsfaktori in Eskilstuna without large changes. Production in Eskilstuna was ended in 1979.

Sauer 80, 90 and 92 are bolt action rifles with a non-rotating bolt and rear-locking rotating lugs. The rifle is known for having a short and smooth bolt travel, but also for being technically complicated.

Sauer 100 is a bolt action rifle manufactured by Sauer & Sohn that was launched in 2016. It is an entry level rifle from Sauer, and is produced on the same factory and shares many parts with Mauser M18.

Scope mount Part for mounting a scope sight to a firearm

Scope mounts are used to attach telescopic sights or other types of sights to firearms. The scope sight itself is usually made for only one of two main types of mounts, which can be classified as scopes for ring mounts or scopes for rail mounts. Words such as mounts and bases are used somewhat loosely, and can refer to several different parts which are either used together or in place of each other as ways to mount optical sights to firearms. When it comes to the interface of the firearm itself, the Picatinny rail is one of the most widespread standard for new firearms as of 2020. While most scopes are made for being mounted either with a ring mount or a rail mount, some sights have an integral mounting mechanism allowing them to be attached directly to the firearm, like for example an integrated Picatinny mount. In addition, there are many proprietary and brand-specific types of mounts that either can be used with Picatinny rails or as alternatives to Picatinny. Scope mounts may be offered by firearm and scope manufacturers, or on the aftermarket.

References

  1. ↑ Bolt Guns - a Survey of Rem 700 Custom Actions | RECOILWEB
  2. ↑ Brownells - Fitted Barrel Instructions
  3. ↑ Custom Rifles | Warner Tool Company
  4. ↑ “Blueprinting” (Truing) a Remington 700 Action – rifleshooter.com
  5. ↑ Upgrading an Older Model 54 Anschütz — Recommended Smiths « Daily Bulletin
  6. ↑ https://www.brownells.com/.aspx/lid=16778/GunTechdetail/Building-An-AK-74-Part-4-Pressing-In-The-Barrel
  7. ↑ Sauer 101 Review | Sporting Rifle magazine "This rifle is not a switch barrel, like its predecessor, but fixed. Sauer opted for a non-threaded, heat shrunk, barrel to receiver fitting"
  8. ↑ New Sauer 101 Hunting Rifle from J.P. Sauer & Sohn « Daily Bulletin "Sauer boasts that the barrel is heat-pressed into the receiver, with the bolt locking up directly into the barrel"
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.