Akaflieg Braunschweig SB-13 Arcus

Last updated
SB13 Arcus
Akaflieg Braunschweig SB-13 Glider D-1113 LFront DMFO 10June2013 (14400270398).jpg
SB-13 at the Deutsches Museum Flugwerft Schleissheim
RoleSingle seat experimental glider
National origin Germany
First flight18 March 1988
Retired2000
Number built1

The Akaflieg Braunschweig SB-13 Arcus was an experimental tailless, single seat, Standard Class glider designed and built in Germany in the early 1990s. Though it performed as well as its conventional contemporaries, it did not offer sufficiently improved performance to compensate for its difficult handling characteristics.

Contents

Design and development

The Akaflieg Braunschweig or Akademische Fliegergruppe Braunschweig (English: The Brunswick Academic Flying Group) is one of some fourteen German undergraduate student flying groups attached to and supported by their home Technical University. Several have designed and built aircraft, often technically advanced and leading the development of gliders in particular. [1] In 1982 when the SB-13 design was first discussed no new tailless glider had been built for thirty years, during which time glass reinforced plastic materials had replaced wood in glider construction and much learned about laminar flow wings; it was hoped that tailless designs would be lighter, simpler and cheaper. [2]

Work on the SB-13 Arcus, named after the cloud formation, began in 1982. Because of the novelty of the layout, a one-third scale model of the early design was built and flown, revealing several serious problems. Strong flutter was experienced even at modest speed and the aircraft was very sensitive to the centre of gravity (c.g.) position. It stalled readily when this was too far aft. Recovery from the spin that followed was difficult. With the c.g. too far forward, a rapid longitudinal "pecking" oscillation set in which, because of its short period, was hard to control. Major redesign, involving long and difficult computer analysis led to a new wing with carbon fibre stiffening on the main spar; in addition, both it and the wing plan were made curved. The new structure resisted flutter until 270 km/h (168 mph) was reached. [2]

The full scale SB-13 finally flew in 1988. Its 15 m (49.2 ft) wing was straight edged, with three slightly tapered sections of increasing sweep. The two inner panels occupied less than 1.9 m (6.2 ft) of the span and the outer section leading edge was swept at about 17°. All had a dihedral of 4°. At its tips, where the chord was 600 mm (24 in), the wing turned upwards into 1,250 mm (49 in) tall, slightly swept winglets, which carried rudders. Elevons occupied much of the outer panel trailing edge and, further inboard, mid-chord mounted airbrakes were fitted. The fuselage, onto which the wings were mounted between low and mid position was a short pod with its nose a little ahead of the centre section leading edge, extending aft about as far as the trailing horizontal edge of the wing at its tip. The pilot reclined under a long, bulged, single piece canopy, which was side hinged to starboard. The cockpit reached beyond the wing both forward and aft, with the main spar passing through it under the pilot's knees. [2]

Despite the modifications made to remove the handling problems predicted by the model, the full scale SB-13 still "pecked" and spun readily; when the standard spin correction procedure was applied, a new spin started in the opposite direction. Over the next few years several aerodynamic devices were tried, some of which at least improved the behaviour of the Arcus; one longer-lasting outcome from the project was the start of an investigation into whole aircraft rescue parachutes. The competition performance of the Arcus was on a par with that of other 15 m gliders of the time but it did not offer the great improvement over them which might have justified even more effort to improve the handling. [2]

Operational history

The sole SB-13 was flown, modified and studied from 1988 to 2000, when it was damaged and set aside in favour of newer aircraft. In 2007 it went to the Deutsches Museum, Munich for exhibition. [3]

Aircraft on display

Specifications

Data from Sailplanes 1965-2000 (characteristics), [2] Akaflieg Braunschweig website (performance), [3] Jane's All the World's Aircraft 1988-89 (performance). [5]

General characteristics

Performance

150 km/h (93 mph; 81 kn) on winch launch

Related Research Articles

Rolladen-Schneider LS6 15-/18 metre single-seat German glider, 1980

The Rolladen-Schneider LS6 is a 15 metre and 18 metre single-seat flapped glider manufactured by Rolladen-Schneider Flugzeugbau GmbH between 1984 and 2003.

Schleicher ASW 24 German glider, 1987

The ASW 24 is a modern single-seat high-performance composite Standard Class sailplane. It is manufactured in Germany by Alexander Schleicher GmbH & Co.

Akaflieg Stuttgart fs24 German single-seat glider, 1957

The Akaflieg Stuttgart fs24, nicknamed Phönix, was a glider designed and built in West Germany from 1951.

Allstar SZD-59 Polish single-seat glider, 1991

The SZD-59 Acro is a single-seat glass composite glider for aerobatics and cross-country flying by PZL Allstar of Bielsko-Biala, Poland.

Akaflieg München Mü13 German single-seat glider, 1935

The Akaflieg München Mü13 Merlin and Akaflieg München Mü13 Atalante were gliders designed and built in Germany from 1935. A motor-glider version of the Merlin was converted by the addition of a small engine in the nose, as the Mü13M Motormerlin. Post-war development as the Mü13E entered production as the Scheibe Bergfalke.

SZD-20X Wampir II Polish single-seat tail-less research glider, 1959

The SZD-20x Wampir II was a single-seat tail-less research glider designed and built in Poland from 1959.

Akaflieg München Mü10 Milan German two-seat glider, 1934

The Akaflieg München Mü10 Milan is a two-seat glider aircraft that was designed in Germany in 1934. Only one copy of the design was built.

Akaflieg München Mü17 Merle German single-seat glider, 1938

The Akaflieg München Mü17 Merle is a single-place glider aircraft that was designed and built in Germany from 1938.

Akaflieg Berlin B12 German two-seat glider, 1977

The Akaflieg Berlin B12 is a high performance two-place glider aircraft that was designed and built in Germany. Conceived as a research vehicle, only one unit was constructed.

Marske Monarch

The Marske Monarch is a single-seat, high-wing, strut-braced, tailless ultralight glider and motor glider that was offered both as plans and a kit for amateur construction by Marske Aircraft.

Akaflieg Braunschweig SB-5 Danzig German single-seat glider, 1959

The Akaflieg Braunschweig SB-5 is a German single-seat Standard Class sailplane designed and prototyped by students of Brunswick University. More than 100 were built to their design, in several different variants.

The Akaflieg Braunschweig SB-10 Schirokko is a German two-seat high performance sailplane designed and built by students of Brunswick University. The sailplane was not intended for production.

The Akaflieg Darmstadt D-40 is an experimental variable geometry single seat sailplane, fitted with almost full span, camber changing flaps for optimum aerodynamics in weak thermals and integrated into the wing so as to minimise flap tip drag. One flew successfully but the D-40, like other variable geometry sailplanes, was not commercialised.

The Akaflieg Braunschweig SB-11 is an experimental, single seat, variable geometry sailplane designed by aeronautical students in Germany. It won the 15 m span class at the World Gliding Championships of 1978 but its advances over the best, more conventional, opposition were not sufficient to lead to widespread imitation.

The Akaflieg Braunschweig SB-12 is a single seat, Standard Class sailplane designed around 1980 by German technical university students to test out a new wing profile from the German Aerospace Centre. It was not intended for production, but the sole SB-12 remains active in 2010.

Akaflieg Stuttgart fs31 Training sailplane designed and built by the Akaflieg Stuttgart in the 1980s.

The Akaflieg Stuttgart fs31 Ferdinand Porsche is a tandem seat, dual control training glider designed and built in Germany between 1977 and 1981. The aircraft was intended to have high performance, yet to be robust enough for student use. It was not intended for production and remains in service with the Akaflieg after almost 40 years and 7,100 flying hours.

The Akaflieg Braunschweig SB-7 Nimbus is a Standard class glider designed and built in Germany in the 1960s. It was one of a series of mixed glass fibre and wood designs from the students of Akaflieg Braunschweig.

The Akaflieg Braunschweig SB-8 is an experimental, single-seat, high performance glider built in Germany in the 1960s, constructed largely from glass fibre skin over built up balsa wood structure. Two were built; the second of which was later fitted with a high aspect ratio (30:1) wing, becoming the Akaflieg Braunschweig SB-9 Stratus.

The Akaflieg Braunschweig SB-6 Nixope was an early (1961) GRP high performance single seat glider designed and built in Germany by aeronautical students from Brunswick University. It competed in the 1961 German National gliding competition, coming sixth, and led directly to two further GRP aircraft.

Akaflieg Karlsruhe AK-5

The AK-5 is a single-seat club class sailplane designed and built in Germany by members of Akaflieg Karlsruhe.

References

  1. ↑ Simons, Martin (2005). Sailplanes 1965-2000 (2nd revised ed.). Königswinter: EQIP Werbung & Verlag GmbH. p. 41. ISBN   3-9808838-1-7.
  2. 1 2 3 4 5 Simons (2005), pp. 49–51.
  3. 1 2 "SB-13 Arcus". Akaflieg Braunschweig. Retrieved 25 July 2012.
  4. ↑ Ogden, Bob (2009). Aviation Museums and Collections of Mainland Europe. Air Britain (Historians) Ltd. ISBN   978-0-85130-418-2.
  5. ↑ Taylor, John W. R., ed. (1988). Jane's All the World's Aircraft 1988-89. London: Jane's Information Group. pp. 620–621. ISBN   0-7106-0867-5.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.