Akaflieg Braunschweig SB-8

Last updated
SB-8
RoleSingle seat experimental glider
National origin West Germany
First flight1967
Number built2
Developed from Akaflieg Braunschweig SB-7 Nimbus
Developed into Akaflieg Braunschweig SB-10 Schirokko

The Akaflieg Braunschweig SB-8 is an experimental, single-seat, high performance glider built in Germany in the 1960s, constructed largely from glass fibre skin over built up balsa wood structure. Two were built; the second of which was later fitted with a high aspect ratio (30:1) wing, becoming the Akaflieg Braunschweig SB-9 Stratus.

Contents

Design and development

The Akaflieg Braunschweig or Akademische Fliegergruppe Braunschweig (English: The Brunswick Academic Flying Group) is one of some fourteen German undergraduate student flying groups sponsored by their home technical university. Several have designed and built aircraft, often technically advanced and leading the development of gliders in particular. The Brunswick students had been exploring the use of GRP in a series of related gliders, beginning with the SB-6. From the SB-8 to the SB-10, wingspan and aspect ratio were progressively increased. Aspect ratio was increased from 23 to 36.6, resulting in aeroelastic problems. [1]

SB-8

The SB-8 is similar to the SB-7, which also had an aspect ratio of 23. It performed well but had difficult handling characteristics, attributed to its Eppler aerofoil section. The SB-8 has an 18 m (59 ft 1 in) wingspan, a two-piece wing of Wortmann FX 62 profile with an unswept leading edge, a slightly tapered centre section, and more strongly tapered outer sections. [1] It is built around a box beam, with balsa ribs and a torsion shell of glass fibre laid over balsa. [2] The wing is shoulder mounted at 1.5° dihedral, [3] with Schempp-Hirth airbrakes at mid-chord midway along the center section and ailerons on the outer panels. [1] Both SB-8 built have camber flaps on the inboard wing panel and ailerons which are coupled to the flaps (flaperons) on the outboard panels. [4]

The fuselage of the SB-8 is built with a fibreglass skin, over a balsa shell, with balsa vertical frames and two pine plywood main formers in the region between the wings. [2] The nose is pointed and slightly drooped, with a short, single piece, canopy just ahead of the wings, tapering gently aft to a straight tapered balsa/GRP T-tail unit. [1] The tailplane carries a conventional single piece elevator [1] and the rudder is fabric covered. [2] On the ground the SB-8 is supported by a retractable, unsprung monowheel undercarriage, assisted by a tail bumper. [3]

The first flight was made from Brunswick airport on 25 April 1967; [2] testing confirmed that the glass fibre structure was too flexible and at high speeds the SB-8 exhibited wing flutter, limiting its maximum permitted speed to 170 km/h (105.6 mph; 91.8 kn). The low wing loading also limited its smooth air cross country speed as there was no provision for ballast. Later, removable steel tubes filled with lead pellets were added to the wing roots of the SB-8 V1 to increase wing loading. A second aircraft, SB-8 V2, was therefore built with a stiffened, heavier wing and provision for water ballast, which addressed both aero-elasticity and wing loading problems, allowing the glider to fly safely, without flutter, at 200 km/h (124.3 mph; 108.0 kn). [1]

SB-9 Stratus

The SB-8 V2 had shown that glass-fibre wings could be made stiff enough to avoid aeroelastic flutter problems and that the higher aspect ratio produced the expected improvement in glide angle. It was natural for the next Akaflieg Braunschweig design to have a wing of greater span, replacing the wing of the SB-8 V2 airframe with a four-panel wing of similar construction but 22 m (72 ft 2 in) span. At the time of its first flight in January 1969 the SB-9 had probably the greatest span of any glider then flying, though the 22 m (72 ft 2 in)-span Holighaus Nimbus 1 flew only three days later. The increase in aspect ratio over the SB-8 increased the measured best glide ratio from 40:1 to 46:1 and decreased the measured minimum sink rate from 0.61 m/s (120.08 ft/min) to 0.51 m/s (100.39 ft/min). The new wing took advantage of the flexibility of glass fibre to implement elastic flaps. The intention was to avoid the interruption to the wing profile at the hinge, particularly on the critical upper surface, and leakage through it by bending the upper surface instead. [1] This method had been used earlier in the wooden-winged HKS-1 glider of 1953. [5]

Operational history

Both SB-8s competed at the German National Championships of 1968, Wolfgang Beduhn finishing fifth in the V1 and Helmut Treiber seventh in the V2. [2] The V2 went on to become the SB-9, but the V1 remained in regular use at Brunswick until 1989. [2] It remained airworthy after that, though flown less often, [2] and was still on the German Civil Aircraft register in 2010. [6]

The SB-9 was used by the Akaflieg students in competitions between 1969 and 1971. [2] It also gave them the opportunity to film and study the alarming motions of the wing when fluttering, recording their observations on film in slow motion and in the air. Two antisymmetric, odd, sine-like lateral displacement modes were observed at 90 km/h (55.9 mph; 48.6 kn). The fundamental mode was seen, at a frequency of 3.3 Hz but at 140 km/h (87.0 mph; 75.6 kn) the wing oscillated at 5.8 Hz in a second harmonic mode. During these largely vertical excursions, the wing also twisted and its overall motion excited vibrations in the rear fuselage and tail unit. [1] [7] The flutter problems were addressed by mass-balancing, the ailerons, and by a span reduction to 21 m (68 ft 11 in). [1]

The career of the SB-9 ended in 1972, when it was decided to use its wing on the SB-10 two-seater, a new design with a very different fuselage and the span increased still further with an 8.7 m (28t ft 7 in) centre section. [1]

Variants

Data from Sailplanes 1965-2000 unless excepted.

SB-8 V1
Original aircraft, empty weight of 260 kg (570 lb) and a maximum take-off weight of 365 kg (805 lb). [3] Flutter restricted maximum permitted speed to 170 km/h (110 mph; 92 kn).
SB-8 V2
Stiffened wing, weights increased by 40 kg (88 lb). Provision for water ballast, maximum permitted speed increased to 200 km/h (120 mph; 110 kn)
SB-9 Stratus
The SB-8V2 modified with a four-part wing of 22 m (72 ft 2 in) span, fitted with elastic flaps. SB-9 Stratus was first flown January 1969. It is Empty weight, 325 kg (717 lb), maximum in flight weight, ballasted, 421 kg (928 lb). Flutter problems tackled with a span reduction to 21 m (68 ft 11 in) and mass-balancing the ailerons.

Specifications (SB-8 V2 & SB-9)

Data from [1]

General characteristics

SB-9: 22 m (72 ft 2 in) (reduced to 21 m (68 ft 11 in) later)
SB-9: 15.48 m2 (166.6 sq ft)
SB-9: 31.3
SB-9: 325 kg (717 lb)
SB-9: 421 kg (928 lb)

Performance

SB-9: 46 at 83 km/h; 52 mph (45 kn)
SB-9: 0.51 m/s (100 ft/min) at 80 km/h (50 mph; 43 kn) at 27.3 kg/m2 (5.6 lb/sq ft) and 414 kg (913 lb)
SB-9: maximum wing loading 27.3 kg/m2 (5.6 lb/sq ft)

Related Research Articles

<span class="mw-page-title-main">Schleicher ASW 15</span> German single-seat glider, 1968

The Schleicher ASW 15 is a single-seat sailplane designed in 1968 by Gerhard Waibel and manufactured by Alexander Schleicher GmbH & Co. The ASW 15 has shoulder-mounted wings and an all-flying tailplane, with its single tow-release placement a compromise between winching and aerotowing. The later ASW 15B had several improvements, including a tow-release placed on the plane of symmetry, an 11 cm taller rudder, a slightly larger main wheel, and the provision of a 90-litre water ballast system.

<span class="mw-page-title-main">Schleicher ASW 12</span> German glider, 1965

The ASW 12, initially known as the AS 12, is a single-seat Sailplane of glass composite construction. The wing is shoulder mounted and it has a T-tail. It is essentially a developed production version of the Akaflieg Darmstadt D-36.

<span class="mw-page-title-main">Akaflieg München Mü27</span> German prototype research glider, 1979

The Mü-27 is a research glider aircraft that designed and built in Germany in 1979. Only one example was constructed.

The SZD-40x Halny is an experimental two-seat glider designed and built in Poland in 1971.

<span class="mw-page-title-main">Akaflieg Berlin B12</span> German two-seat glider, 1977

The Akaflieg Berlin B12 is a high performance two-place glider aircraft that was designed and built in Germany. Conceived as a research vehicle, only one unit was constructed.

<span class="mw-page-title-main">Akaflieg Braunschweig SB-5 Danzig</span> German single-seat glider, 1959

The Akaflieg Braunschweig SB-5 is a German single-seat Standard Class sailplane designed and prototyped by students of Brunswick University. More than 100 were built to their design, in several different variants.

The Akaflieg Braunschweig SB-10 Schirokko is a German two-seat high performance sailplane designed and built by students of Brunswick University. The sailplane was not intended for production.

<span class="mw-page-title-main">Akaflieg Stuttgart fs26</span> German single-seat motor glider, 1970

The Akaflieg Stuttgart fs26 Moseppl is a German single-seat motor glider with twin fins and rudders designed and built by Akaflieg Stuttgart. First flown on the 25 September 1970 it was designed as an experiment and not intended for production.

The Akaflieg Darmstadt D-40 is an experimental variable geometry single seat sailplane, fitted with almost full span, camber changing flaps for optimum aerodynamics in weak thermals and integrated into the wing so as to minimise flap tip drag. One flew successfully but the D-40, like other variable geometry sailplanes, was not commercialised.

The Akaflieg Braunschweig SB-11 is an experimental, single seat, variable geometry sailplane designed by aeronautical students in Germany. It won the 15 m span class at the World Gliding Championships of 1978 but its advances over the best, more conventional, opposition were not sufficient to lead to widespread imitation.

The Akaflieg Darmstadt D-39 was a single-seat motor glider derived from the D-38 sailplane. Built in Germany in the late 1970s, it was not intended for production and only one was constructed.

The Akaflieg Braunschweig SB-12 is a single seat, Standard Class sailplane designed around 1980 by German technical university students to test out a new wing profile from the German Aerospace Centre. It was not intended for production, but the sole SB-12 remains active in 2010.

The FVA-20 F. B. Schmetz was a single seat, Standard Class sailplane, built as a one-off aircraft, to explore the application of glass fibre to glider construction. Built over a long period, it finally flew in late 1979.

The Akaflieg Braunschweig SB-7 Nimbus is a Standard class glider designed and built in Germany in the 1960s. It was one of a series of mixed glass fibre and wood designs from the students of Akaflieg Braunschweig.

<span class="mw-page-title-main">Akaflieg Braunschweig SB-13 Arcus</span> German single-seat glider, 1988

The Akaflieg Braunschweig SB-13 Arcus was an experimental tailless, single seat, Standard Class glider designed and built in Germany in the early 1990s. Though it performed as well as its conventional contemporaries, it did not offer sufficiently improved performance to compensate for its difficult handling characteristics.

<span class="mw-page-title-main">ISF Mistral-C</span> German single-seat glider, 1976

The Mistral-C was one of the first gliders, designed in 1974 to the then new Club Class rules. It was based on the Strauber Mistral, a Standard Class glider flown a year earlier, but with a new wing and built from newer composite materials. Both types were designed and constructed in Germany. More than 75 Mistral-Cs were produced.

The Akaflieg Braunschweig SB-6 Nixope was an early (1961) GRP high performance single seat glider designed and built in Germany by aeronautical students from Brunswick University. It competed in the 1961 German National gliding competition, coming sixth, and led directly to two further GRP aircraft.

The Schleicher K 10 is a Standard class competition glider, designed by Rudolf Kaiser and built in Germany in 1963. Only a few were produced.

The Bertoni Altinger AB-1 Superalbatros,, is a high-performance sailplane designed and built in Argentina in the 1950s and 1960s.

<span class="mw-page-title-main">Akaflieg Braunschweig SB-14</span> German single-seat glider, 2003

The Akaflieg Braunschweig SB 14 is an 18 m (59 ft) Open-class sailplane designed and built in Germany in the early 2000s.

References

  1. 1 2 3 4 5 6 7 8 9 10 11 Simons, Martin (2005). Sailplanes 1965-2000 (2nd revised ed.). Königswinter: EQIP Werbung & Verlag GmbH. pp.  41–5. ISBN   3 9808838 1 7.
  2. 1 2 3 4 5 6 7 8 Brütting, Georg (1973). Die berümtesten Segelflugzeuge. Stuttgart: Motorbuch Verlag. p. 119. ISBN   3 87943171 X.
  3. 1 2 3 Taylor, John W R (1966). Jane's All the World's Aircraft 1966-67. London: Sampson Low, Marston & Co. Ltd. p. 390.
  4. ↑ "SB-8" . Retrieved 19 July 2012.
  5. ↑ Simons, Martin (2006). Sailplanes 1945-1965 (2nd revised ed.). Königswinter: EQIP Werbung & Verlag GmbH. pp.  154–7. ISBN   3 9807977 4 0.
  6. ↑ Partington, Dave (2010). European registers handbook 2010. Air Britain (Historians) Ltd. ISBN   978-0-85130-425-0.
  7. ↑ "Flutter on the SB-8" . Retrieved 19 July 2012.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.