Cooler

Last updated
Portable Ice Chest, U.S. Patent # 2,663,167 (1953) PortableIceChestPatent1955.jpg
Portable Ice Chest, U.S. Patent # 2,663,167 (1953)

A cooler, portable ice chest, ice box, cool box, [1] chilly bin (in New Zealand), or esky (Australia) is an insulated box used to keep food or drink cool.

Contents

Ice cubes are most commonly placed in it to help the contents inside stay cool. Ice packs are sometimes used, as they either contain the melting water inside, or have a gel sealed inside that stays cold longer than plain ice (absorbing heat as it changes phase).

Coolers are often taken on picnics, and on vacation or holiday. Where summers are hot, they may also be used just for getting cold groceries home from the store, such as keeping ice cream from melting in a hot automobile. Even without adding ice, this can be helpful, particularly if the trip home will be lengthy. Some coolers have built-in cupholders in the lid.

Insulated beverage cooler 2008-09-20 Dispensing water into the mash tun.jpg
Insulated beverage cooler

They are usually made with interior and exterior shells of plastic, with a hard foam in between. They come in sizes from small personal ones to large family ones with wheels. Disposable ones are made solely from polystyrene foam (such as is a disposable coffee cup) about 2 cm or one inch thick. Most reusable ones have molded-in handles; a few have shoulder straps. The cooler has developed from just a means of keeping beverages cold into a mode of transportation with the ride-on cooler. A thermal bag, cooler bag or cool bag is very similar in concept, but typically smaller and not rigid.

History

The original inventor of the cooler is unknown, with versions becoming available in various parts of the world throughout the 1950s.

The portable ice chest was patented in the USA by Richard C. Laramy of Joliet, Illinois. On February 24, 1951, Laramy filed an application with the United States Patent Office for a portable ice chest (Serial No. 212,573). [2] The patent (#2,663,157) was issued December 22, 1953.

In 1952, the portable Esky Auto Box was released in Australia by the Sydney refrigeration company Malley’s. Made from steel and finished in baked enamel and chrome, with cork sheeting for insulation, the Esky became the first mass produced cooler on the market. The brand found huge success and by 1960, 500,000 Australian households owned one (in a country of approximately 3 million households at the time).

The Coleman Company popularized the cooler within the USA with its initial offering of a galvanized steel cooler in 1954. Three years later, Coleman developed a process to make a plastic liner for coolers and jugs.

Thermoelectric coolers

Some modern coolers are thermoelectric, plugging into a car's cigarette lighter socket. Rather than using a compressor and refrigerant such as a refrigerator or other heat pump, these use the Peltier effect along with an external fan to draw away the heat. By reversing the current, this concept can also heat the contents instead of cooling them, useful for keeping meals hot from a drive-through, or even to keep items from freezing in severely cold climates.

Thermoelectric coolers typically can drop the temperature by about 40 °F or 22 °C below ambient temperature, or can raise it by at least that much; this is really a function of the effectiveness of the boxes' thermal insulation. Some better units even have digital thermostat controls. They do draw a significant amount of power, however, and can drain a non running car's battery so much so that it cannot start. Most electric coolers have an undervoltage shutoff at around 10 or 10.5 volts to prevent this. Many come with power adapters, which use an electronic transformer to convert AC mains or line voltage down to 12 volts, with a lighter-like socket for the cooler's cord to plug in. Some also have a crossover-connection device to reverse the current for heating service.

Rotationally molded coolers

Rotationally molded (roto-molded) coolers have become popular in recent years. Roto-molded coolers are manufactured using a process called rotational molding, a process by which a heated and softened material is applied to the inner wall of a slowly rotating mold. The mold continues to rotate during the cooling phase, producing a thick and uniform final product. In the case of roto-molded coolers, the heated liquid plastic is applied over a thick layer of insulation. The resulting product has no seals or imperfections and is much stronger and more durable than traditional coolers. Examples of roto-molded coolers include YETI, [3] ORCA [4] or Grizzly coolers. [5]

Ride-on coolers

A ride-on cooler is a means of transportation that can store and cool beverages and other food products. It is a combination of a low power engine with a go-cart frame which uses the cooler as a seat. The ride-on cooler has the ability to transport food and drinks short distances and can be used in a small backyard, a neighborhood, or at large outdoor parties. The ride-on cooler can be equipped with a trailer hitch, allowing it to tow an extra cooler as a trailer.

Designs use either gas-powered lawnmower engines or electric motors which are lighter, more energy efficient, and quieter. Both can have a wide range of power. The electric motors range from 250 watts (0.3 hp) to 2,000 watts (2.7 hp) and generally use 12- to 60-volt batteries. [6] [7] Gas-powered engines range from 33 to 205 cubic centimetres (2.0 to 12.5  cu in ) with a typical top-speed of 13 miles per hour (21 km/h), [8] but enthusiasts have built much faster versions.

The legal status of the ride-on cooler varies from country to country and in the US from state to state. In some jurisdictions, a driver's license is required to operate any form of motor vehicle on public roads, and an intoxicated driver can be convicted of driving under the influence for riding one. [9]

See also

Related Research Articles

<span class="mw-page-title-main">Refrigeration</span> Process of moving heat from one location to another in controlled conditions

Refrigeration is any of various types of cooling of a space, substance, or system to lower and/or maintain its temperature below the ambient one. Refrigeration is an artificial, or human-made, cooling method.

<span class="mw-page-title-main">Vacuum flask</span> Insulated storage vessel

A vacuum flask is an insulating storage vessel that greatly lengthens the time over which its contents remain hotter or cooler than the flask's surroundings. Invented by Sir James Dewar in 1892, the vacuum flask consists of two flasks, placed one within the other and joined at the neck. The gap between the two flasks is partially evacuated of air, creating a near-vacuum which significantly reduces heat transfer by conduction or convection. When used to hold cold liquids, this also virtually eliminates condensation on the outside of the flask.

<span class="mw-page-title-main">Sleeping bag</span> Insulated covering for a person

A sleeping bag is an insulated covering for a person, essentially a lightweight quilt that can be closed with a zipper or similar means to form a tube, which functions as lightweight, portable bedding in situations where a person is sleeping outdoors. It is also commonly used indoors for people who do not have beds or at sleepovers. Its primary purpose is to provide warmth and thermal insulation through its synthetic or down insulation. It also typically has a water-resistant or water-repellent cover that protects, to some extent, against wind chill and light precipitation, but a tent is usually used in addition to a sleeping bag, as it performs those functions better. The bottom surface also provides some cushioning, but a sleeping pad or camp cot is usually used in addition to that purpose. The bottom surface of a sleeping bag may be moderately water repellent, but a plastic tarp or groundsheet is often used to protect against moist ground.

<span class="mw-page-title-main">Thermoelectric cooling</span> Electrically powered heat-transfer

Thermoelectric cooling uses the Peltier effect to create a heat flux at the junction of two different types of materials. A Peltier cooler, heater, or thermoelectric heat pump is a solid-state active heat pump which transfers heat from one side of the device to the other, with consumption of electrical energy, depending on the direction of the current. Such an instrument is also called a Peltier device, Peltier heat pump, solid state refrigerator, or thermoelectric cooler (TEC) and occasionally a thermoelectric battery. It can be used either for heating or for cooling, although in practice the main application is cooling. It can also be used as a temperature controller that either heats or cools.

<span class="mw-page-title-main">Evaporative cooler</span> Device that cools air through the evaporation of water

An evaporative cooler is a device that cools air through the evaporation of water. Evaporative cooling differs from other air conditioning systems, which use vapor-compression or absorption refrigeration cycles. Evaporative cooling exploits the fact that water will absorb a relatively large amount of heat in order to evaporate. The temperature of dry air can be dropped significantly through the phase transition of liquid water to water vapor (evaporation). This can cool air using much less energy than refrigeration. In extremely dry climates, evaporative cooling of air has the added benefit of conditioning the air with more moisture for the comfort of building occupants.

<span class="mw-page-title-main">Refrigerator</span> Appliance for cold food storage

A refrigerator, colloquially fridge, is a commercial and home appliance consisting of a thermally insulated compartment and a heat pump that transfers heat from its inside to its external environment so that its inside is cooled to a temperature below the room temperature. Refrigeration is an essential food storage technique around the world. The lower temperature lowers the reproduction rate of bacteria, so the refrigerator reduces the rate of spoilage. A refrigerator maintains a temperature a few degrees above the freezing point of water. The optimal temperature range for perishable food storage is 3 to 5 °C. A similar device that maintains a temperature below the freezing point of water is called a freezer. The refrigerator replaced the icebox, which had been a common household appliance for almost a century and a half. The United States Food and Drug Administration recommends that the refrigerator be kept at or below 4 °C (40 °F) and that the freezer be regulated at −18 °C (0 °F).

Esky is a brand of portable coolers, originally Australian, derived from the word "Eskimo". The term "esky" is also commonly used in Australia to generically refer to portable coolers or ice boxes and is part of the Australian vernacular, in place of words like "cooler" or "cooler box" and the New Zealand "chilly bin".

<span class="mw-page-title-main">Ice pack</span> Filled bag designed to be frozen

An ice pack or gel pack is a portable bag filled with water, refrigerant gel, or liquid, meant to provide cooling. They can be divided into the reusable type, which works as a thermal mass and requires freezing, or the instant type, which cools itself down using chemicals but can only be used once. The instant type is generally limited to medical use as a cold compress to alleviate the pain of minor injuries, while the reusable type is both used as a cold compress and to keep food cool in portable coolers or in insulated shipping containers to keep products cool during transport.

<span class="mw-page-title-main">Hand warmer</span> Small packet that produces heat

Hand warmers are small, often disposable, packets that produce heat to warm cold hands. They are used throughout the world in a variety of ways, including outdoor recreation, manual labor, and homelessness.

<span class="mw-page-title-main">Icemaker</span>

An icemaker, ice generator, or ice machine may refer to either a consumer device for making ice, found inside a home freezer; a stand-alone appliance for making ice, or an industrial machine for making ice on a large scale. The term "ice machine" usually refers to the stand-alone appliance.

<span class="mw-page-title-main">Air conditioning</span> Cooling of air in an enclosed space

Air conditioning, often abbreviated as A/C (US) or air con (UK), is the process of removing heat from an enclosed space to achieve a more comfortable interior environment and in some cases also strictly controlling the humidity of internal air. Air conditioning can be achieved using a mechanical 'air conditioner' or by other methods, including passive cooling and ventilative cooling. Air conditioning is a member of a family of systems and techniques that provide heating, ventilation, and air conditioning (HVAC). Heat pumps are similar in many ways to air conditioners, but use a reversing valve to allow them both to heat and to cool an enclosed space.

<span class="mw-page-title-main">Thermoelectric generator</span> Device that converts heat flux into electrical energy

A thermoelectric generator (TEG), also called a Seebeck generator, is a solid state device that converts heat directly into electrical energy through a phenomenon called the Seebeck effect. Thermoelectric generators function like heat engines, but are less bulky and have no moving parts. However, TEGs are typically more expensive and less efficient.

<span class="mw-page-title-main">Automobile auxiliary power outlet</span> Outlet for portable accessories

An automobile auxiliary power outlet in an automobile was initially designed to power an electrically heated cigarette lighter, but became a de facto standard DC connector to supply electrical power for portable accessories used in or near an automobile directly from the vehicle's electrical system. Such include mobile phone chargers, cooling fans, portable fridges, electric air pumps, and power inverters.

Thermophotonics is a concept for generating usable power from heat which shares some features of thermophotovoltaic (TPV) power generation. Thermophotonics was first publicly proposed by solar photovoltaic researcher Martin Green in 2000. However, no TPX device is known to have been demonstrated to date, apparently because of the stringent requirement on the emitter efficiency.

<span class="mw-page-title-main">Heated clothing</span> Functional clothing

Most heated clothing is designed for cold-weather sports and activities, such as motorcycle riding, downhill skiing, diving, winter biking, and snowmobiling, trekking and for outdoor workers such as construction workers and carpenters. Since the London Olympics, heated clothing has also been used by athletes to keep their muscles warm between the warm-up and the race.

Insulated shipping containers are a type of packaging used to ship temperature sensitive products such as foods, pharmaceuticals, organs, blood, biologic materials, vaccines and chemicals. They are used as part of a cold chain to help maintain product freshness and efficacy. The term can also refer to insulated intermodal containers or insulated swap bodies.

<span class="mw-page-title-main">Thermal management of high-power LEDs</span>

High power light-emitting diodes (LEDs) can use 350 milliwatts or more in a single LED. Most of the electricity in an LED becomes heat rather than light. If this heat is not removed, the LEDs run at high temperatures, which not only lowers their efficiency, but also makes the LED less reliable. Thus, thermal management of high power LEDs is a crucial area of research and development. It is necessary to limit both the junction and the phosphor particles temperatures to a value that will guarantee the desired LED lifetime.

<span class="mw-page-title-main">Solar-powered refrigerator</span>

A solar-powered refrigerator is a refrigerator which runs on energy directly provided by sun, and may include photovoltaic or solar thermal energy.

A jockey box is an insulated container containing ice and water, as well as a long coil of hollow tubing. The device is used to cool beverages being served on tap in temporary locations.

Many vaccines require refrigeration to remain active, and the lack of infrastructure to maintain the cool chain to reliably bring vaccines into more remote areas of developing countries poses a serious challenge to national immunization programs. Portable vaccine cooler units have been proposed by several technologists. The WHO Performance, Quality and Safety (PQS) programme is a driver of the technology.

References

  1. "coolbox - definition of coolbox by Macmillan Dictionary". Macmillandictionary.com. Archived from the original on 2017-06-23. Retrieved 2013-07-11.
  2. United States. Patent Office (1953). Official Gazette of the United States Patent Office. The Office. p. 931.
  3. "Premium Coolers, Drinkware, Gear, and Apparel". yeti.com. Archived from the original on 2018-11-23. Retrieved 2018-11-24.
  4. "ORCA COOLERS". ORCA. Archived from the original on 2018-11-30. Retrieved 2018-11-24.
  5. "why". Grizzly Coolers. Archived from the original on 2019-09-15. Retrieved 2018-11-24.
  6. "Coolermods". Archived from the original on 2018-10-26. Retrieved 2018-10-25.
  7. "Watts Usage by Ride-on-Coolers". Archived from the original on 2022-01-01. Retrieved 2022-01-01.
  8. "Cruzin Cooler Official Site". Cruzincooler.com. Archived from the original on 2014-01-04. Retrieved 2014-02-09.
  9. "Video: Australian man convicted for driving motorised cool box while drunk". Telegraph. Archived from the original on 2011-08-18. Retrieved 2014-02-09.

11. EVERUN COOLERS丨explore fun in nature