Endurance time method

Last updated

The endurance time (ET) method is a dynamic structural analysis procedure for seismic assessment of structures. In this procedure, an intensifying dynamic excitation is used as the loading function. [1] Endurance time method is a time-history based dynamic analysis procedure. An estimate of the structural response at different equivalent seismic intensity levels is obtained in a single response history analysis. [2] This method has applications in seismic assessment of various structural types and in different areas of earthquake engineering. [3] [4] [5]

Contents

The concept of endurance time method

Endurance time (ET) method is a dynamic structural analysis procedure in which intensifying dynamic excitation is used as the loading function. An estimate of structural response and/or performance at the entire seismic intensity range of interest is obtained in each response history analysis. The concept of endurance time analysis is similar to the exercise test applied in medicine. [6] Similar concept has also been extended to applications in the analysis of offshore platforms under water waves. [7]

Development history

The basic concepts of the endurance time method were published in 2004. [8] Application in linear seismic analysis appeared in 2007. [2] ET was subsequently extended to nonlinear analysis of single degree of freedom (SDOF) and multi degree of freedom systems. [9] Procedures for multi-component seismic analysis were subsequently developed. [10] [11] [12] [13]

ET excitation functions

ET excitation functions are generated by using numerical optimization methods. [14] [15] ET excitation functions are publicly available through internet websites. [1] [16] ET excitation functions can be categorized into five generations as follows:

  1. First generation of ET excitation functions (ETEFs) are essentially a filtered and profiled white noise. These were used for demonstrating the concept of ET and have limited practical significance. [8]
  2. Second-generation ETEFs incorporate response spectrum matching. These ETEFs produce numerically significant analysis results. [17]
  3. Third-generation ETEFs are optimized in nonlinear range. These ETEFs deliver improved analysis performance.
  4. Fourth-generation ETEFs are optimized to include duration consistency. [18]
  5. Fifth-generation ETEFs are optimized to include damage consistency. [19]
Fig. 1. A typical endurance time excitation function (ETA20f03 record) ETA20f03 Endutance Time Excitation Function.png
Fig. 1. A typical endurance time excitation function (ETA20f03 record)

Application areas in earthquake engineering

Endurance time method has been applied in the following areas of earthquake engineering:

Structural type applications

ET method has been applied in seismic assessment of the following structural types:

Advantages of ET method

Major advantages of the endurance time method are as follows:

Limitations of ET method

Major limitations of the endurance time method are as follows:

Related Research Articles

In metallurgy, a shape-memory alloy (SMA) is an alloy that can be deformed when cold but returns to its pre-deformed ("remembered") shape when heated. It is also known in other names such as memory metal, memory alloy, smart metal, smart alloy, and muscle wire. The "memorized geometry" can be modified by fixating the desired geometry and subjecting it to a thermal treatment, for example a wire can be taught to memorize the shape of a coil spring.

<span class="mw-page-title-main">Seismic retrofit</span> Modification of existing structures to make them more resistant to seismic activity

Seismic retrofitting is the modification of existing structures to make them more resistant to seismic activity, ground motion, or soil failure due to earthquakes. With better understanding of seismic demand on structures and with recent experiences with large earthquakes near urban centers, the need of seismic retrofitting is well acknowledged. Prior to the introduction of modern seismic codes in the late 1960s for developed countries and late 1970s for many other parts of the world, many structures were designed without adequate detailing and reinforcement for seismic protection. In view of the imminent problem, various research work has been carried out. State-of-the-art technical guidelines for seismic assessment, retrofit and rehabilitation have been published around the world – such as the ASCE-SEI 41 and the New Zealand Society for Earthquake Engineering (NZSEE)'s guidelines. These codes must be regularly updated; the 1994 Northridge earthquake brought to light the brittleness of welded steel frames, for example.

Induced seismicity is typically earthquakes and tremors that are caused by human activity that alters the stresses and strains on Earth's crust. Most induced seismicity is of a low magnitude. A few sites regularly have larger quakes, such as The Geysers geothermal plant in California which averaged two M4 events and 15 M3 events every year from 2004 to 2009. The Human-Induced Earthquake Database (HiQuake) documents all reported cases of induced seismicity proposed on scientific grounds and is the most complete compilation of its kind.

Earthquake engineering is an interdisciplinary branch of engineering that designs and analyzes structures, such as buildings and bridges, with earthquakes in mind. Its overall goal is to make such structures more resistant to earthquakes. An earthquake engineer aims to construct structures that will not be damaged in minor shaking and will avoid serious damage or collapse in a major earthquake. A properly engineered structure does not necessarily have to be extremely strong or expensive. It has to be properly designed to withstand the seismic effects while sustaining an acceptable level of damage.

In geotechnical civil engineering, the p–y is a method of analyzing the ability of deep foundations to resist loads applied in the lateral direction. This method uses the finite difference method and p-y graphs to find a solution. P–y graphs are graphs which relate the force applied to soil to the lateral deflection of the soil. In essence, non-linear springs are attached to the foundation in place of the soil. The springs can be represented by the following equation:

<span class="mw-page-title-main">Fluid–structure interaction</span>

Fluid–structure interaction (FSI) is the interaction of some movable or deformable structure with an internal or surrounding fluid flow. Fluid–structure interactions can be stable or oscillatory. In oscillatory interactions, the strain induced in the solid structure causes it to move such that the source of strain is reduced, and the structure returns to its former state only for the process to repeat.

<span class="mw-page-title-main">Earthquake-resistant structures</span> Structures designed to protect buildings from earthquakes

Earthquake-resistant or aseismic structures are designed to protect buildings to some or greater extent from earthquakes. While no structure can be entirely impervious to earthquake damage, the goal of earthquake engineering is to erect structures that fare better during seismic activity than their conventional counterparts. According to building codes, earthquake-resistant structures are intended to withstand the largest earthquake of a certain probability that is likely to occur at their location. This means the loss of life should be minimized by preventing collapse of the buildings for rare earthquakes while the loss of the functionality should be limited for more frequent ones.

Scientia Iranica is a peer-reviewed scientific journal published by Sharif University of Technology. It was established in 1991 and covers theoretical and experimental research in technical sciences and engineering. Starting in 2011, the journal is published open access. The editor-in-chief is Abolhassan Vafai.

In geophysics, geology, civil engineering, and related disciplines, seismic noise is a generic name for a relatively persistent vibration of the ground, due to a multitude of causes, that is often a non-interpretable or unwanted component of signals recorded by seismometers.

Incremental dynamic analysis (IDA) is a computational analysis method of earthquake engineering for performing a comprehensive assessment of the behavior of structures under seismic loads. It has been developed to build upon the results of probabilistic seismic hazard analysis in order to estimate the seismic risk faced by a given structure. It can be considered to be the dynamic equivalent of the static pushover analysis.

Mete Avni Sözen was Kettelhut Distinguished Professor of Structural Engineering at Purdue University, Indiana, United States from 1992 to 2018.

<span class="mw-page-title-main">Vibration fatigue</span>

Vibration fatigue is a mechanical engineering term describing material fatigue, caused by forced vibration of random nature. An excited structure responds according to its natural-dynamics modes, which results in a dynamic stress load in the material points. The process of material fatigue is thus governed largely by the shape of the excitation profile and the response it produces. As the profiles of excitation and response are preferably analyzed in the frequency domain it is practical to use fatigue life evaluation methods, that can operate on the data in frequency-domain, s power spectral density (PSD).

<span class="mw-page-title-main">Earthquake rotational loading</span>

Earthquake rotational loading indicates the excitation of structures due to the torsional and rocking components of seismic actions. Nathan M. Newmark was the first researcher who showed that this type of loading may result in unexpected failure of structures, and its influence should be considered in design codes. There are various phenomena that may lead to the earthquake rotational loading of structures, such as propagation of body wave, surface wave, special rotational wave, block rotation, topographic effect, and soil structure interaction.

<span class="mw-page-title-main">Medhat Haroun</span> Egyptian-American expert on earthquake engineering

Medhat Haroun was an Egyptian-American expert on earthquake engineering. He wrote more than 300 technical papers and received the Charles Martin Duke Lifeline Earthquake Engineering Award (2006) and the Walter Huber Civil Engineering Research Prize (1992) from the American Society of Civil Engineers.

This glossary of structural engineering terms pertains specifically to structural engineering and its sub-disciplines. Please see glossary of engineering for a broad overview of the major concepts of engineering.

Pres-Lam is a method of mass engineered timber construction that uses high strength unbonded steel cables or bars to create connections between timber beams and columns or columns and walls and their foundations. As a prestressed structure the steel cables clamp members together creating connections which are stronger and more compact than traditional timber fastening systems. In earthquake zones, the steel cables can be coupled with internal or external steel reinforcing which provide additional strength and energy dissipation creating a damage avoiding structural system.

Andrew Stuart Whittaker is an American structural engineer who is currently a SUNY Distinguished Professor in the Department of Civil, Structural and Environmental Engineering at the University at Buffalo, State University of New York.

<span class="mw-page-title-main">Kit Miyamoto</span> Japanese American structural engineer (born 1963)

Dr. Hideki "Kit" Miyamoto is a Japanese American structural engineer known for being the founder-CEO of Miyamoto International, a global structural engineering and disaster risk reduction organization. He is also the chairman of California's Alfred E. Alquist Seismic Safety Commission, which investigates earthquakes and recommends policies for risk reduction.

The Steel Network, Inc, aka TSN is a United States-based company headquartered in Durham, North Carolina, that manufactures light steel framing building components for commercial and residential construction. TSN is the parent company of Applied Science International.

<span class="mw-page-title-main">Tensioned stone</span> Form of stonework used in construction

Tensioned stone is a high-performance composite construction material: stone held in compression with tension elements. The tension elements can be connected to the outside of the stone, but more typically tendons are threaded internally through a drilled duct.

References

  1. 1 2 Endurance Time Method website[Online]. https://sites.google.com/site/etmethod/
  2. 1 2 Estekanchi, H.E., Valamanesh, V. and Vafai, A. (2007), Application of Endurance Time Method in Linear Seismic Analysis, Engineering Structures, v29, n10, p2551-2562, doi:10.1016/j.engstruct.2007.01.009
  3. ↑ Estekanchi, H. E., Mashayekhi, M., Vafai, H., Ahmadi, G., Mirfarhadi, S. A., & Harati, M. (2020, October). A state-of-knowledge review on the Endurance Time Method. In Structures (Vol. 27, pp. 2288-2299). Elsevier. https://doi.org/10.1016/j.istruc.2020.07.062
  4. ↑ Estekanchi, H., & Vafai, H. (2018). Seismic analysis and design using the endurance time method, Volume I: Concepts and development. Momentum Press.
  5. ↑ Estekanchi, H., & Vafai, H. (2018). Seismic analysis and design using the endurance time method, Volume II: Advanced topics and application. Momentum Press.
  6. ↑ Estekanchi, H. E.; Riahi, H. T. and Vafai, A. (2009), Endurance Time Method: Exercise Test as Applied to Structures, Asian Journal of Civil Engineering, v10, n5, p559-577, Link
  7. ↑ Zeinoddini, M., Nikoo, H. M. and Estekanchi H.E. (2012), "Endurance Wave Analysis (EWA) and its application for assessment of offshore structures under extreme waves", Applied Ocean Research, v37, p98-110, doi: 10.1016/j.apor.2012.04.003
  8. 1 2 Estekanchi, H. E., A. Vafai and M. Sadeghazar (2004), Endurance Time method for seismic analysis and design of structures, Scientia Iranica, v11, n4, p361-370, Link
  9. 1 2 Riahi, H. T. and Estekanchi, H. E, (2010), "Seismic Assessment of Steel Frames with Endurance Time Method", Journal of Constructional Steel Research, v66, n6, p780-792, doi:10.1016/j.jcsr.2009.12.001
  10. ↑ Valamanesh, V and Estekanchi, H. E. (2010),"A Study of Endurance Time Method in the Analysis of Elastic Moment Frames under Three-Directional Seismic Loading ", Asian Journal of Civil Engineering, v11, n5, p543-562, Link
  11. ↑ Valamanesh, V and Estekanchi, H. E. (2010), "Compatibility of the endurance time method with codified seismic analysis approaches on three-dimensional analysis of steel frames ", The Structural Design of Tall and Special Buildings, doi:10.1002/tal.666
  12. ↑ Valamanesh, V and Estekanchi, H. E. (2011), "Endurance time method for multi-component analysis of steel elastic moment frames", Scientia Iranica, v18, n2, p139-142, doi:10.1016/j.scient.2011.03.024
  13. 1 2 3 Valamanesh V. and Estekanchi H. E. (2012), "Nonlinear Seismic Assessment of Steel Moment Frames under Bi-Directional Loading via Endurance Time Method", The Structural Design of Tall and Special Buildings, doi: 10.1002/tal.1054
  14. ↑ Valamanesh, V; Estekanchi, H. E. and Vafai, A. (2010), Characteristics of Second Generation Endurance Time Accelerograms, Scientia Iranica, v17, n1, p53-61, Link
  15. ↑ Kaveh A., Mahdavi V., "Generation of Endurance Time Acceleration Functions Using the Wavelet Transform". Iran University of Science & Technology. 2012; 2 (2) :203–219,Link
  16. ↑ Estekanchi HE. 2012. Website of the Endurance Time method. [Online]. http://sharif.edu/~stkanchi/ET
  17. ↑ Mashayekhi, M. and Estekanchi, H.E. (2012), "Significance of effective number of cycles in Endurance Time analysis", Asian Journal of Civil Engineering, v13, n5, p647-657, Link
  18. ↑ Mashayekhi, M., Estekanchi, H. E., Vafai, A., & Mirfarhadi, S. A. (2018). Simulation of cumulative absolute velocity consistent endurance time excitations. Journal of Earthquake Engineering, 1-26. https://doi.org/10.1080/13632469.2018.1540371
  19. ↑ Mashayekhi, M., Estekanchi, H. E., Vafai, H., & Mirfarhadi, S. A. (2018). Development of hysteretic energy compatible endurance time excitations and its application. Engineering Structures, 177, 753-769. https://doi.org/10.1016/j.engstruct.2018.09.089
  20. ↑ Estekanchi, H. E., Arjomandi, K and Vafai, A. (2008), Estimating Structural Damage of Steel Moment Frames by Endurance Time Method, Journal of Constructional Steel Research, v64, n2, p145-155, doi:10.1016/j.jcsr.2007.05.010
  21. ↑ Riahi, H. T. ; Estekanchi, H. E. and Vafai, A. (2009), Estimates of Average Inelastic Deformation Demands for Regular Steel Frames by the Endurance Time Method, Scientia Iranica, v16, n5, p388-402, Link
  22. 1 2 3 Hasani, H., Golafshani, A., Estekanchi, H. Seismic performance evaluation of jacket-type offshore platforms using endurance time method considering soil-pile-superstructure interaction. Scientia Iranica, 2017; 24(4): 1843-1854. doi: 10.24200/sci.2017.4275 http://scientiairanica.sharif.edu/article_4275_f79d8b4fdd0cc8d159b91b1a3b968585.pdf
  23. ↑ Estekanchi, H. E. and Basim, M. Ch. (2011), "Optimal damper placement in steel frames by the Endurance Time method", The Structural Design of Tall and Special Buildings, v20, n5, p612-630, doi:10.1002/tal.689
  24. ↑ Shirkhani A., Farahmand Azar, B., Charkhtab Basim, M., & Mashayekhi M. (2021). Performance-based optimal distribution of viscous dampers in structure using hysteretic energy compatible endurance time excitations. International Journal of Numerical Methods in Civil Engineering, 5 (3), 46-55. http://dx.doi.org/10.52547/nmce.5.3.46
  25. ↑ Shirkhani, A., Mualla, I. H., Shabakhty, N., & Mousavi, S. R. (2015). Behavior of steel frames with rotational friction dampers by endurance time method. Journal of Constructional Steel Research, 107, 211-222. https://doi.org/10.1016/j.jcsr.2015.01.016
  26. ↑ Shirkhani, A., Farahmand Azar, B., & Basim, M. C. (2020). Optimum slip load of T-shaped friction dampers in steel frames by endurance time method. Proceedings of the Institution of Civil Engineers-Structures and Buildings, 173(10), 746-760. https://doi.org/10.1680/jstbu.18.00169
  27. ↑ Shirkhani, A., Farahmand Azar, B., & Charkhtab Basim, M. (2021). Seismic loss assessment of steel structures equipped with rotational friction dampers subjected to intensifying dynamic excitations. Engineering Structures, 238. https://doi.org/10.1016/j.engstruct.2021.112233
  28. ↑ Application of Endurance Time (ET) method in optimal design of energy dissipation systems [Online]. https://sites.google.com/view/ascivil/endurance-time/
  29. ↑ Mirzai, A, Estekanchi, H. E. and Vafai, A. (2010), "Application of Endurance Time Method in Performance Based Design of Steel Moment Frames", Scientia Iranica, v17, n6, p482-492, Link
  30. ↑ Mirzai A., Estekanchi, H. E. and Vafai, A. (2012), "Improved methodology for endurance time analysis: From time to seismic hazard return period", Scientia Iranica, doi: 10.1016/j.scient.2012.06.023
  31. ↑ Mirzaee, A., & Estekanchi, H. E. (2015). Performance-based seismic retrofitting of steel frames by the endurance time method. Earthquake Spectra, 31(1), 383-402. https://doi.org/10.1193/081312EQS262M
  32. ↑ Basim, M. C., & Estekanchi, H. E. (2015). Application of endurance time method in performance-based optimum design of structures. Structural safety, 56, 52-67. https://doi.org/10.1016/j.strusafe.2015.05.005
  33. ↑ Jaberi, V., Jaberi, M., & Asghari, A. (2024). A new performance-based seismic design method using endurance time analysis for linked column frame system and a comparison of structural systems and seismic analysis methods. The Structural Design of Tall and Special Buildings, e2100. https://doi.org/10.1002/tal.2100
  34. ↑ Jaberi, V. (2023). Collapse-based design method for simple seismic design of complex structural systems such as linked column frame system. Structures, 2023 Sep 1 (Vol. 55, pp. 482-497). https://doi.org/10.1016/j.istruc.2023.06.059
  35. ↑ Charkhtab Basim, M., E Estekanchi, H., & Vafai, A. (2016). A methodology for value based seismic design of structures by the endurance time method. Scientia Iranica, 23(6), 2514-2527. https://dx.doi.org/10.24200/sci.2016.2310
  36. ↑ Mirfarhadi, S. A., & Estekanchi, H. E. (2020). Value based seismic design of structures using performance assessment by the endurance time method. Structure and Infrastructure Engineering, 1-19. https://doi.org/10.1080/15732479.2020.1712436
  37. ↑ Nozari, A and Estekanchi, H. E. (2011) "Optimization of Endurance Time acceleration functions for seismic assessment of structures, International Journal of Optimization in Civil Engineering, v1, n2, 257–277, Link
  38. ↑ Sarcheshmehpour, M., Estekanchi, H. E., & Ghannad, M. A. (2020). Optimum placement of supplementary viscous dampers for seismic rehabilitation of steel frames considering soil–structure interaction. The Structural Design of Tall and Special Buildings, 29(1), e1682. https://doi.org/10.1002/tal.1682
  39. ↑ Bai, J., Jin, S., Zhao, J., & Sun, B. (2019). Seismic performance evaluation of soil-foundation-reinforced concrete frame systems by endurance time method. Soil Dynamics and Earthquake Engineering, 118, 47-51. https://doi.org/10.1016/j.soildyn.2018.12.011
  40. 1 2 Estekanchi, H. E. and Alembagheri, , M. (2012), "Seismic analysis of steel liquid storage tanks by Endurance Time method", Thin-Walled Structures, v50, n1, p14-23, doi: 10.1016/j.tws.2011.08.015
  41. 1 2 Valamanesh, V; Estekanchi, H. E., Vafai, A and Ghaemian M. (2011), "Application of Endurance time method in seismic analysis of concrete gravity dams", Scientia Iranica A, v18, n3, p326-337, doi:10.1016/j.scient.2011.05.039
  42. ↑ Ghaffari, E., E Estekanchi, H., & Vafai, A. (2020). Application of endurance time method in seismic analysis of bridges. Scientia Iranica, 27(4), 1751-1761. https://dx.doi.org/10.24200/sci.2018.5041.1382
  43. ↑ Guo, A., Shen, Y., Bai, J., & Li, H. (2017). Application of the endurance time method to the seismic analysis and evaluation of highway bridges considering pounding effects. Engineering Structures, 131, 220-230. https://doi.org/10.1016/j.engstruct.2016.11.009
  44. ↑ He, H., Wei, K., Zhang, J., & Qin, S. (2020). Application of endurance time method to seismic fragility evaluation of highway bridges considering scour effect. Soil Dynamics and Earthquake Engineering, 136, 106243. https://doi.org/10.1016/j.soildyn.2020.106243
  45. ↑ Bazmooneh, Amirali (2009), Application of Endurance Time method in seismic evaluation of existing steel buildings, Thesis presented to the Department of Civil Engineering as a partial requirement for degree of Master of Science, Sharif University of Technology http://library.sharif.ir/parvan/resource/290141/
  46. ↑ Avanaki, M. J., Estekanchi H.E. (2012), "Collapse analysis by Endurance Time method", International Journal of Optimization in Civil Engineering, v2, n2, p287-299,Link
  47. ↑ Estekanchi, H. E., Riahi, H. T. and Vafai, A. (2011), Application of Endurance Time Method in Seismic Assessment of Steel Frames", Engineering Structures, v33, n9, p2535-2546 doi:10.1016/j.engstruct.2011.04.025
  48. ↑ Mohsenian, V., Hajirasouliha, I., & Nikkhoo, A. (2020). Multi-level Response Modification Factor Estimation for Steel Moment-Resisting Frames Using Endurance-Time Method. Journal of Earthquake Engineering, 1-21. https://doi.org/10.1080/13632469.2020.1845875
  49. ↑ Ghaffari, Esmail (2010) Application of Endurance Time method in Seismic analysis of bridges, Thesis presented to the Department of Civil Engineering as a partial requirement for degree of Master of Science, Sharif University of Technology http://library.sharif.ir/parvan/resource/291956/
  50. ↑ Pang, Y., Cai, L., He, W., & Wu, L. (2020). Seismic assessment of deep water bridges in reservoir considering hydrodynamic effects using endurance time analysis. Ocean Engineering, 198, 106846. https://doi.org/10.1016/j.oceaneng.2019.106846
  51. ↑ Hariri Ardebili M., Mirzabozorg H., Kianoush R., "A Study on Nonlinear Behavior and Seismic Damage Assessment of Concrete Arch Dam-Reservoir-Foundation System Using Endurance Time Analysis". Iran University of Science & Technology. 2012; 2 (4) :573–606 Link
  52. ↑ Tavazo, M., Estekanchi H.E. and Kaldi P. (2012), "Endurance time method in the linear seismic analysis of shell structures", International Journal of Civil Engineering, v10, n3, p169-178,Link
  53. ↑ Alembagheri, M and Estekanchi, H. E. (2011), "Seismic Assessment of Unanchored Steel Storage Tanks by Endurance Time Method", Earthquake Engineering and Engineering Vibration, v10, n4, p591-604, doi:10.1007/s11803-011-0092-y
  54. ↑ Madarshahian, R., Estekanchi, H. E. and Mahvashmohammadi, A. (2011), "Estimating seismic demand parameters with Endurance Time method", Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), v12, n8, p616-626, doi:10.1631/jzus.A1000389
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.