Fiber Bragg grating

A fiber Bragg grating (FBG) is a type of distributed Bragg reflector constructed in a short segment of optical fiber that reflects particular wavelengths of light and transmits all others. This is achieved by creating a periodic variation in the refractive index of the fiber core, which generates a wavelength-specific dielectric mirror. Hence a fiber Bragg grating can be used as an inline optical filter to block certain wavelengths, can be used for sensing applications, ^[1] or it can be used as wavelength-specific reflector.

Figure 1: A Fiber Bragg Grating structure, with refractive index profile and spectral response

History

The first in-fiber Bragg grating was demonstrated by Ken Hill in 1978. ^[2] Initially, the gratings were fabricated using a visible laser propagating along the fiber core. In 1989, Gerald Meltz and colleagues demonstrated the much more flexible transverse holographic inscription technique where the laser illumination came from the side of the fiber. This technique uses the interference pattern of ultraviolet laser light ^[3] to create the periodic structure of the fiber Bragg grating.

Theory

Figure 2: FBG reflected power as a function of wavelength

The fundamental principle behind the operation of an FBG is Fresnel reflection, where light traveling between media of different refractive indices may both reflect and refract at the interface.

The refractive index will typically alternate over a defined length. The reflected wavelength (${\displaystyle \lambda _{B}}$), called the Bragg wavelength, is defined by the relationship,

${\displaystyle \lambda _{B}=2n_{e}\Lambda }$

where ${\displaystyle n_{e}}$ is the effective refractive index of the fiber core and ${\displaystyle \Lambda }$ is the grating period. The effective refractive index quantifies the velocity of propagating light as compared to its velocity in vacuum. ${\displaystyle n_{e}}$ depends not only on the wavelength but also (for multimode waveguides) on the mode in which the light propagates. For this reason, it is also called modal index.

The wavelength spacing between the first minima (nulls, see Fig. 2), or the bandwidth (${\displaystyle \Delta \lambda }$), is (in the strong grating limit) given by,

${\displaystyle \Delta \lambda =\left[{\frac {2\delta n_{0}\eta }{\pi }}\right]\lambda _{B}}$

where ${\displaystyle \delta n_{0}}$ is the variation in the refractive index (${\displaystyle n_{3}-n_{2}}$), and ${\displaystyle \eta }$ is the fraction of power in the core. Note that this approximation does not apply to weak gratings where the grating length, ${\displaystyle L_{g}}$, is not large compared to ${\displaystyle \lambda _{B}}$ \ ${\displaystyle \delta n_{0}}$.

The peak reflection (${\displaystyle P_{B}(\lambda _{B})}$) is approximately given by,

${\displaystyle P_{B}(\lambda _{B})\approx \tanh ^{2}\left[{\frac {N\eta (V)\delta n_{0}}{n}}\right]}$

where ${\displaystyle N}$ is the number of periodic variations. The full equation for the reflected power (${\displaystyle P_{B}(\lambda )}$), is given by,

${\displaystyle P_{B}(\lambda )={\frac {\sinh ^{2}\left[\eta (V)\delta n_{0}{\sqrt {1-\Gamma ^{2}}}{\frac {N\Lambda }{\lambda }}\right]}{\cosh ^{2}\left[\eta (V)\delta n_{0}{\sqrt {1-\Gamma ^{2}}}{\frac {N\Lambda }{\lambda }}\right]-\Gamma ^{2}}}}$

where,

${\displaystyle \Gamma (\lambda )={\frac {1}{\eta (V)\delta n_{0}}}\left[{\frac {\lambda }{\lambda _{B}}}-1\right]}$

Types of gratings

The term type in this context refers to the underlying photosensitivity mechanism by which grating fringes are produced in the fiber. The different methods of creating these fringes have a significant effect on physical attributes of the produced grating, particularly the temperature response and ability to withstand elevated temperatures. Thus far, five (or six) types of FBG have been reported with different underlying photosensitivity mechanisms. ^[4] These are summarized below:

Standard, or type I, gratings

Written in both hydrogenated and non-hydrogenated fiber of all types, type I gratings are usually known as standard gratings and are manufactured in fibers of all types under all hydrogenation conditions. Typically, the reflection spectra of a type I grating is equal to 1-T where T is the transmission spectra. This means that the reflection and transmission spectra are complementary and there is negligible loss of light by reflection into the cladding or by absorption. Type I gratings are the most commonly used of all grating types, and the only types of grating available off-the-shelf at the time of writing.

Type IA gratings

Regenerated grating written after erasure of a type I grating in hydrogenated germanosilicate fiber of all types

Type IA gratings were first observed in 2001 ^[5] during experiments designed to determine the effects of hydrogen loading on the formation of IIA gratings in germanosilicate fiber. In contrast to the anticipated decrease (or 'blue shift') of the gratings' Bragg wavelength, a large increase (or 'red shift') was observed.

Later work showed that the increase in Bragg wavelength began once an initial type I grating had reached peak reflectivity and begun to weaken. For this reason, it was labeled as a regenerated grating.

Determination of the type IA gratings' temperature coefficient showed that it was lower than a standard grating written under similar conditions.

The key difference between the inscription of type IA and IIA gratings is that IA gratings are written in hydrogenated fibers, whereas type IIA gratings are written in non-hydrogenated fibers. ^{[6] [7]}

Type IIA, or type In, gratings

These are gratings that form as the negative part of the induced index change overtakes the positive part. It is usually associated with gradual relaxation of induced stress along the axis and/or at the interface. It has been proposed that these gratings could be relabeled type In (for type 1 gratings with a negative index change; type II label could be reserved for those that are distinctly made above the damage threshold of the glass). ^[8]

Later research by Xie et al. showed the existence of another type of grating with similar thermal stability properties to the type II grating. This grating exhibited a negative change in the mean index of the fiber and was termed type IIA. The gratings were formed in germanosilicate fibers with pulses from a frequency doubled XeCl pumped dye laser. It was shown that initial exposure formed a standard (type I) grating within the fiber which underwent a small red shift before being erased. Further exposure showed that a grating reformed which underwent a steady blue shift whilst growing in strength. ^{[9] [10]}

Regenerated gratings

These are gratings that are reborn at higher temperatures after erasure of gratings, usually type I gratings and usually, though not always, in the presence of hydrogen. They have been interpreted in different ways including dopant diffusion (oxygen being the most popular current interpretation) and glass structural change. Recent work has shown that there exists a regeneration regime beyond diffusion where gratings can be made to operate at temperatures in excess of 1,295 °C, outperforming even type II femtosecond gratings. ^[11] These are extremely attractive for ultra high temperature applications.

Type II gratings

Damage written gratings inscribed by multiphoton excitation with higher intensity lasers that exceed the damage threshold of the glass. Lasers employed are usually pulsed in order to reach these intensities. They include recent developments in multiphoton excitation using femtosecond pulses where the short timescales (commensurate on a timescale similar to local relaxation times) offer unprecedented spatial localization of the induced change. The amorphous network of the glass is usually transformed via a different ionization and melting pathway to give either higher index changes or create, through micro-explosions, voids surrounded by more dense glass.

Archambault et al. showed that it was possible to inscribe gratings of ~100% (>99.8%) reflectance with a single UV pulse in fibers on the draw tower. The resulting gratings were shown to be stable at temperatures as high as 800 °C (up to 1,000 °C in some cases, and higher with femtosecond laser inscription). The gratings were inscribed using a single 40 mJ pulse from an excimer laser at 248 nm. It was further shown that a sharp threshold was evident at ~30 mJ; above this level the index modulation increased by more than two orders of magnitude, whereas below 30 mJ the index modulation grew linearly with pulse energy. For ease of identification, and in recognition of the distinct differences in thermal stability, they labeled gratings fabricated below the threshold as type I gratings and above the threshold as type II gratings. Microscopic examination of these gratings showed a periodic damage track at the grating's site within the fiber [10]; hence type II gratings are also known as damage gratings. However, these cracks can be very localized so as to not play a major role in scattering loss if properly prepared. ^{[12] [13]}

Grating structure

Figure 3: Structure of the refractive index change in a uniform FBG (1), a chirped FBG (2), a tilted FBG (3), and a superstructure FBG (4).

Figure 4: Refractive index profile in the core of, 1) a uniform positive-only FBG, 2) a Gaussian-apodized FBG, 3) a raised-cosine-apodized FBG with zero-dc change, and 4) a discrete phase shift FBG.

The structure of the FBG can vary via the refractive index, or the grating period. The grating period can be uniform or graded, and either localised or distributed in a superstructure. The refractive index has two primary characteristics, the refractive index profile, and the offset. Typically, the refractive index profile can be uniform or apodized, and the refractive index offset is positive or zero.

There are six common structures for FBGs; ^[14]

1. uniform positive-only index change,
2. Gaussian apodized,
3. raised-cosine apodized,
4. chirped,
5. discrete phase shift, and
6. superstructure.

The first complex grating was made by J. Canning in 1994. ^{[15] [ citation needed ]} This supported the development of the first distributed feedback (DFB) fiber lasers, and also laid the groundwork for most complex gratings that followed, including the sampled gratings first made by Peter Hill and colleagues in Australia.^{[ citation needed ]}

Apodized gratings

There are basically two quantities that control the properties of the FBG. These are the grating length, ${\displaystyle L_{g}}$, given as

${\displaystyle L_{g}=N\Lambda }$

and the grating strength, ${\displaystyle \delta n_{0}\eta }$. There are, however, three properties that need to be controlled in a FBG. These are the reflectivity, the bandwidth, and the side-lobe strength. As shown above, in the strong grating limit (i.e., for large ${\displaystyle \delta n_{0}}$) the bandwidth depends on the grating strength, and not the grating length. This means the grating strength can be used to set the bandwidth. The grating length, effectively ${\displaystyle \scriptstyle N}$, can then be used to set the peak reflectivity, which depends on both the grating strength and the grating length. The result of this is that the side-lobe strength cannot be controlled, and this simple optimisation results in significant side-lobes. A third quantity can be varied to help with side-lobe suppression. This is apodization of the refractive index change. The term apodization refers to the grading of the refractive index to approach zero at the end of the grating. Apodized gratings offer significant improvement in side-lobe suppression while maintaining reflectivity and a narrow bandwidth. The two functions typically used to apodize a FBG are Gaussian and raised-cosine.

Chirped fiber Bragg gratings

The refractive index profile of the grating may be modified to add other features, such as a linear variation in the grating period, called a chirp. The reflected wavelength changes with the grating period, broadening the reflected spectrum. A grating possessing a chirp has the property of adding dispersion—namely, different wavelengths reflected from the grating will be subject to different delays. This property has been used in the development of phased-array antenna systems and polarization mode dispersion compensation, as well.

Tilted fiber Bragg gratings

In standard FBGs, the grading or variation of the refractive index is along the length of the fiber (the optical axis), and is typically uniform across the width of the fiber. In a tilted FBG (TFBG), the variation of the refractive index is at an angle to the optical axis. The angle of tilt in a TFBG has an effect on the reflected wavelength, and bandwidth.^{[ clarification needed ]}

Long-period gratings

Typically the grating period is the same size as the Bragg wavelength, as shown above. For a grating that reflects at 1,500 nm, the grating period is 500 nm, using a refractive index of 1.5. Longer periods can be used to achieve much broader responses than are possible with a standard FBG. These gratings are called long-period fiber grating. They typically have grating periods on the order of 100 micrometers, to a millimeter, and are therefore much easier to manufacture. ^{[16] [17] [18]}

Phase-shifted fiber Bragg gratings

Phase-shifted fiber Bragg gratings (PS-FBGs) are an important class of gratings structures which have interesting applications in optical communications and sensing due to their special filtering characteristics. ^[19] These types of gratings can be reconfigurable through special packaging and system design. ^[20]

Different coatings of diffractive structure are used for fiber Bragg gratings in order to reduce the mechanical impact on the Bragg wavelength shift for 1.1–15 times as compared to an uncoated waveguide. ^[21]

Addressed fiber Bragg structures

Addressed fiber Bragg structures (AFBS) is an emerging class of FBGs developed in order to simplify interrogation and enhance performance of FBG-based sensors. The optical frequency response of an AFBS has two narrowband notches with the frequency spacing between them being in the radio frequency (RF) range. The frequency spacing is called the address frequency of AFBS and is unique for each AFBS in a system. The central wavelength of AFBS can be defined without scanning its spectral response, unlike conventional FBGs that are probed by optoelectronic interrogators. An interrogation circuit of AFBS is significantly simplified in comparison with conventional interrogators and consists of a broadband optical source, an optical filter with a predefined linear inclined frequency response, and a photodetector. ^{[22] [23]}

Manufacture

Fiber Bragg gratings are created by "inscribing" or "writing" systematic (periodic or aperiodic) variation of refractive index into the core of a special type of optical fiber using an intense ultraviolet (UV) source such as a UV laser. Two main processes are used: interference and masking. The method that is preferable depends on the type of grating to be manufactured. Although polymer optic fibers starting gaining research interest in the 2000s, germanium-doped silica fiber is most commonly used. ^[24] The germanium-doped fiber is photosensitive, which means that the refractive index of the core changes with exposure to UV light. The amount of the change depends on the intensity and duration of the exposure as well as the photosensitivity of the fiber. To write a high reflectivity fiber Bragg grating directly in the fiber the level of doping with germanium needs to be high. However, standard fibers can be used if the photosensitivity is enhanced by pre-soaking the fiber in hydrogen.

Interference

This was the first method used widely for the fabrication of fiber Bragg gratings and uses two-beam interference. Here the UV laser is split into two beams which interfere with each other creating a periodic intensity distribution along the interference pattern. The refractive index of the photosensitive fiber changes according to the intensity of light that it is exposed to. This method allows for quick and easy changes to the Bragg wavelength, which is directly related to the interference period and a function of the incident angle of the laser light.

Sequential writing

Complex grating profiles can be manufactured by exposing a large number of small, partially overlapping gratings in sequence. Advanced properties such as phase shifts and varying modulation depth can be introduced by adjusting the corresponding properties of the subgratings. ^[25] In the first version of the method, subgratings were formed by exposure with UV pulses, but this approach had several drawbacks, such as large energy fluctuations in the pulses and low average power. A sequential writing method with continuous UV radiation that overcomes these problems has been demonstrated and is now used commercially. ^[26] The photosensitive fiber is translated by an interferometrically controlled airbearing borne carriage. The interfering UV beams are focused onto the fiber, and as the fiber moves, the fringes move along the fiber by translating mirrors in an interferometer. As the mirrors have a limited range, they must be reset every period, and the fringes move in a sawtooth pattern. All grating parameters are accessible in the control software, and it is therefore possible to manufacture arbitrary gratings structures without any changes in the hardware.

Photomask

A photomask having the intended grating features may also be used in the manufacture of fiber Bragg gratings. The photomask is placed between the UV light source and the photosensitive fiber. The shadow of the photomask then determines the grating structure based on the transmitted intensity of light striking the fiber. Photomasks are specifically used in the manufacture of chirped Fiber Bragg gratings, which cannot be manufactured using an interference pattern.

Point-by-point

A single UV laser beam may also be used to 'write' the grating into the fiber point-by-point. Here, the laser has a narrow beam that is equal to the grating period. The main difference of this method lies in the interaction mechanisms between infrared laser radiation and dielectric material - multiphoton absorption and tunnel ionization. ^[27] This method is specifically applicable to the fabrication of long period fiber gratings. Point-by-point is also used in the fabrication of tilted gratings.

Production

Originally, the manufacture of the photosensitive optical fiber and the 'writing' of the fiber Bragg grating were done separately. Today, production lines typically draw the fiber from the preform and 'write' the grating, all in a single stage. As well as reducing associated costs and time, this also enables the mass production of fiber Bragg gratings. Mass production is in particular facilitating applications in smart structures utilizing large numbers (3000) of embedded fiber Bragg gratings along a single length of fiber.

Applications

Communications

Figure 5: Optical add-drop multiplexer.

The primary application of fiber Bragg gratings is in optical communications systems. They are specifically used as notch filters. They are also used in optical multiplexers and demultiplexers with an optical circulator, or optical add-drop multiplexer (OADM). Figure 5 shows 4 channels, depicted as 4 colours, impinging onto a FBG via an optical circulator. The FBG is set to reflect one of the channels, here channel 4. The signal is reflected back to the circulator where it is directed down and dropped out of the system. Since the channel has been dropped, another signal on that channel can be added at the same point in the network.

A demultiplexer can be achieved by cascading multiple drop sections of the OADM, where each drop element uses an FBG set to the wavelength to be demultiplexed. Conversely, a multiplexer can be achieved by cascading multiple add sections of the OADM. FBG demultiplexers and OADMs can also be tunable. In a tunable demultiplexer or OADM, the Bragg wavelength of the FBG can be tuned by strain applied by a piezoelectric transducer. The sensitivity of a FBG to strain is discussed below in fiber Bragg grating sensors.

Fiber Bragg grating sensors

As well as being sensitive to strain, the Bragg wavelength is also sensitive to temperature. This means that fiber Bragg gratings can be used as sensing elements in optical fiber sensors. In a FBG sensor, the measurand causes a shift in the Bragg wavelength, ${\displaystyle \Delta \lambda _{B}}$. The relative shift in the Bragg wavelength, ${\displaystyle \Delta \lambda _{B}/\lambda _{B}}$, due to an applied strain (${\displaystyle \epsilon }$) and a change in temperature (${\displaystyle \Delta T}$) is approximately given by,

${\displaystyle \left[{\frac {\Delta \lambda _{B}}{\lambda _{B}}}\right]=C_{S}\epsilon +C_{T}\Delta T}$

or,

${\displaystyle \left[{\frac {\Delta \lambda _{B}}{\lambda _{B}}}\right]=(1-p_{e})\epsilon +(\alpha _{\Lambda }+\alpha _{n})\Delta T}$

Here, ${\displaystyle C_{S}}$ is the coefficient of strain, which is related to the strain optic coefficient${\displaystyle p_{e}}$. Also, ${\displaystyle C_{T}}$ is the coefficient of temperature, which is made up of the thermal expansion coefficient of the optical fiber, ${\displaystyle \alpha _{\Lambda }}$, and the thermo-optic coefficient, ${\displaystyle \alpha _{n}}$. ^[28]

Fiber Bragg gratings can then be used as direct sensing elements for strain and temperature. They can also be used as transduction elements, converting the output of another sensor, which generates a strain or temperature change from the measurand, for example fiber Bragg grating gas sensors use an absorbent coating, which in the presence of a gas expands generating a strain, which is measurable by the grating. Technically, the absorbent material is the sensing element, converting the amount of gas to a strain. The Bragg grating then transduces the strain to the change in wavelength.

Specifically, fiber Bragg gratings are finding uses in instrumentation applications such as seismology, ^[29] pressure sensors for extremely harsh environments, and as downhole sensors in oil and gas wells for measurement of the effects of external pressure, temperature, seismic vibrations and inline flow measurement. As such they offer a significant advantage over traditional electronic gauges used for these applications in that they are less sensitive to vibration or heat and consequently are far more reliable. In the 1990s, investigations were conducted for measuring strain and temperature in composite materials for aircraft and helicopter structures. ^{[30] [31]}

Fiber Bragg gratings used in fiber lasers

Recently the development of high power fiber lasers has generated a new set of applications for fiber Bragg gratings (FBGs), operating at power levels that were previously thought impossible. In the case of a simple fiber laser, the FBGs can be used as the high reflector (HR) and output coupler (OC) to form the laser cavity. The gain for the laser is provided by a length of rare earth doped optical fiber, with the most common form using Yb³⁺ ions as the active lasing ion in the silica fiber. These Yb-doped fiber lasers first operated at the 1 kW CW power level in 2004 ^[32] based on free space cavities but were not shown to operate with fiber Bragg grating cavities until much later. ^[33]

Such monolithic, all-fiber devices are produced by many companies worldwide and at power levels exceeding 1 kW. The major advantage of these all fiber systems, where the free space mirrors are replaced with a pair of fiber Bragg gratings (FBGs), is the elimination of realignment during the life of the system, since the FBG is spliced directly to the doped fiber and never needs adjusting. The challenge is to operate these monolithic cavities at the kW CW power level in large mode area (LMA) fibers such as 20/400 (20 μm diameter core and 400 μm diameter inner cladding) without premature failures at the intra-cavity splice points and the gratings. Once optimized, these monolithic cavities do not need realignment during the life of the device, removing any cleaning and degradation of fiber surface from the maintenance schedule of the laser. However, the packaging and optimization of the splices and FBGs themselves are non-trivial at these power levels as are the matching of the various fibers, since the composition of the Yb-doped fiber and various passive and photosensitive fibers needs to be carefully matched across the entire fiber laser chain. Although the power handling capability of the fiber itself far exceeds this level, and is possibly as high as >30 kW CW, the practical limit is much lower due to component reliability and splice losses. ^[34]

Process of matching active and passive fibers

In a double-clad fiber there are two waveguides – the Yb-doped core that forms the signal waveguide and the inner cladding waveguide for the pump light. The inner cladding of the active fiber is often shaped to scramble the cladding modes and increase pump overlap with the doped core. The matching of active and passive fibers for improved signal integrity requires optimization of the core/clad concentricity, and the MFD through the core diameter and NA, which reduces splice loss. This is principally achieved by tightening all of the pertinent fiber specifications. ^[35]

Matching fibers for improved pump coupling requires optimization of the clad diameter for both the passive and the active fiber. To maximize the amount of pump power coupled into the active fiber, the active fiber is designed with a slightly larger clad diameter than the passive fibers delivering the pump power. As an example, passive fibers with clad diameters of 395-μm spliced to active octagon shaped fiber with clad diameters of 400-μm improve the coupling of the pump power into the active fiber. An image of such a splice is shown, showing the shaped cladding of the doped double-clad fiber. ^[36]

The matching of active and passive fibers can be optimized in several ways. The easiest method for matching the signal carrying light is to have identical NA and core diameters for each fiber. This however does not account for all the refractive index profile features. Matching of the MFD is also a method used to create matched signal carrying fibers. It has been shown that matching all of these components provides the best set of fibers to build high power amplifiers and lasers. Essentially, the MFD is modeled and the resulting target NA and core diameter are developed. The core-rod is made and before being drawn into fiber its core diameter and NA are checked. Based on the refractive index measurements, the final core/clad ratio is determined and adjusted to the target MFD. This approach accounts for details of the refractive index profile which can be measured easily and with high accuracy on the preform, before it is drawn into fiber. ^[36]

See also

• Bragg's law
• Dielectric mirror
• Diffraction
  • Diffraction grating
• Distributed temperature sensing by fiber optics
• Hydrogen sensor
• Long-period fiber grating
• PHOSFOS project – embedding FBGs in flexible skins
• Photonic crystal fiber

References

1. Gao, Wenjing; Liu, Jianxia; Guo, Huiyong; Jiang, Xin; Sun, Shaofa; Yu, Haihu (June 1, 2022). "Multi-Wavelength Ultra-Weak Fiber Bragg Grating Arrays for Long-Distance Quasi-Distributed Sensing". Photonic Sensors. 12 (2): 185–195. Bibcode:2022PhSen..12..185G. doi: 10.1007/s13320-021-0635-4 . ISSN   2190-7439. S2CID   237744822.
2. Hill, K.O.; Fujii, Y.; Johnson, D. C.; Kawasaki, B. S. (1978). "Photosensitivity in optical fiber waveguides: application to reflection fiber fabrication". Appl. Phys. Lett. 32 (10): 647. Bibcode:1978ApPhL..32..647H. doi:10.1063/1.89881.
3. Meltz, G.; et al. (1989). "Formation of Bragg gratings in optical fibers by a transverse holographic method". Opt. Lett. 14 (15): 823–5. Bibcode:1989OptL...14..823M. doi:10.1364/OL.14.000823. PMID   19752980.
4. J. Canning, Fiber Gratings and Devices for Sensors and Lasers, Laser and Photonics Reviews, 2 (4), 275-289, Wiley, USA (2008)
5. Liu, Y. (2001). Advanced fiber gratings and their application (Thesis). Aston University. S2CID   107311300.
6. Simpson, A. G. (2005). Optical Fiber Sensors and Their Interrogation (Thesis). Aston University. S2CID   137254600.
7. Simpson, A. G.; Kalli, K.; Zhou, K.; Zhang, L.; Bennion, I. (2003). "A method for the fabrication of temperature compensating IA-I strain sensors". OFS16. Nara, Japan. pp. postdeadline paper PD4.
8. For a contemporary review, see J. Canning (2008). "Fiber Gratings and Devices for Sensors and Lasers". Laser and Photonics Reviews. 2 (4). Wiley: 275–289. Bibcode:2008LPRv....2..275C. doi:10.1002/lpor.200810010. S2CID   120508715.
9. Xie, W. X.; Niay, P.; Bernage, P.; Douay, M.; Bayon, J. F.; Georges, T.; Monerie, M.; Poumellec, B. (1993). "Experimental-Evidence of 2 Types of Photorefractive Effects Occurring During Photo inscriptions of Bragg Gratings Within Germanosilicate Fibers". Optics Communications. 104 (1–3): 185–195. Bibcode:1993OptCo.104..185X. doi:10.1016/0030-4018(93)90127-Q.
10. Niay, P.; Bernage, P.; Legoubin, S.; Douay, M.; Xie, W. X.; Bayon, J. F.; Georges, T.; Monerie, M.; Poumellec, B. (1994). "Behaviour of Spectral Transmissions of Bragg Gratings Written in Germania-Doped Fibers - Writing and Erasing Experiments Using Pulsed or CW UV Exposure". Optics Communications. 113 (1–3): 176–192. Bibcode:1994OptCo.113..176N. doi:10.1016/0030-4018(94)90606-8.
11. Canning, J.; Stevenson, M.; Bandyopadhyay, S.; Cook, K. (2008). "Extreme silica optical fibre gratings". Sensors. 8 (10): 6448–6452. Bibcode:2008Senso...8.6448C. CiteSeerX   10.1.1.412.2022 . doi: 10.3390/s8106448 . PMC   3707460 . PMID   27873879.
12. Dong, L.; Archambault, J. L.; Reekie, L.; Russell, P. S. J.; Payne, D. N. (1993). "Single-Pulse Bragg Gratings Written During Fibre Drawing" (PDF). Electronics Letters. 29 (17): 1577–1578. Bibcode:1993ElL....29.1577D. doi:10.1049/el:19931051.
13. Archambault, J. L.; Reekie, L.; Russell, P. S. J. (1993). "100-Percent Reflectivity Bragg Reflectors Produced in Optical Fibres By Single Excimer-Laser Pulses" (PDF). Electronics Letters. 29 (5): 453–455. Bibcode:1993ElL....29..453A. doi:10.1049/el:19930303.
14. Erdogan, Turan (August 1997). "Fiber Grating Spectra". Journal of Lightwave Technology. 15 (8): 1277–1294. Bibcode:1997JLwT...15.1277E. doi:10.1109/50.618322.
15. J. Canning, M. G. Sceats, "p-phase-shifted periodic distributed structures in germanosilicate fiber by UV post-processing", Electron. Lett., 30, (16), 1344-1345, (1994)
16. T. Erdogan, 'Cladding-mode resonances in short- and long-period fiber grating filters', J. Opt. Soc. Am. A, 14, pp. 1760–1773, 1997
17. S Bandyopadhyay, P Biswas, F Chiavaioli, TK Dey, N Basumallick, 'Long-period fiber grating: a specific design for biosensing applications', Applied Optics 56 (35), 9846-9853
18. S. Ghosh, K. Dissanayake, S. Asokan, T. Sun, B. M. A. Rahman, Kenneth T. V. Grattan; 'Lead (Pb2+) ion sensor development using optical fiber gratings and nanocomposite materials', Sensors and Actuators B: Chemical, 2022, 364, pp. 131818
19. Agrawal, G. P.; Radic, S. (1994). "Phase-shifted fiber Bragg gratings and their application for wavelength demultiplexing". IEEE Photonics Technology Letters. 6 (8): 995–997. Bibcode:1994IPTL....6..995A. doi:10.1109/68.313074. ISSN   1041-1135. S2CID   44014971.
20. Falah, A. A. S.; Mokhtar, M. R.; Yusoff, Z.; Ibsen, M. (2016). "Reconfigurable Phase-Shifted Fiber Bragg Grating Using Localized Micro-Strain". IEEE Photonics Technology Letters. 28 (9): 951–954. doi:10.1109/LPT.2016.2519249. ISSN   1041-1135. S2CID   2247089.
21. Munko A.S.; Varzhel S.V.; Arkhipov S.V.; Zabiyakin A.N. (2015). "Protective coatings of fiber Bragg grating for minimizing of mechanical impact on its wavelength characteristics". Scientific and Technical Journal of Information Technologies, Mechanics and Optics. 15 (2).
22. Agliullin, T. A.; Gubaidullin, R. R.; Morozov, O. G.; Zh. Sahabutdinov, A.; Ivanov, V. (March 2019). "Tire Strain Measurement System Based on Addressed FBG-Structures". 2019 Systems of Signals Generating and Processing in the Field of on Board Communications. Moscow, Russia: IEEE. pp. 1–5. doi:10.1109/SOSG.2019.8706815. ISBN   978-1-7281-0606-9. S2CID   146118643.
23. Morozov, O G; Sakhabutdinov, A Zh; Nureev, I I; Misbakhov, R Sh (November 2019). "Modelling and record technologies of address fibre Bragg structures based on two identical ultra-narrow gratings with different central wavelengths". Journal of Physics: Conference Series. 1368 (2): 022049. Bibcode:2019JPhCS1368b2049M. doi: 10.1088/1742-6596/1368/2/022049 . ISSN   1742-6588.
24. Zhifeng, Zhang (2015), Tao, Xiaoming (ed.), "Polymer Optical Fiber Bragg Grating", Handbook of Smart Textiles, Singapore: Springer, pp. 597–613, doi:10.1007/978-981-4451-45-1_27, ISBN   978-981-4451-45-1
25. R. Stubbe, B. Sahlgren, S. Sandgren, and A. Asseh, "Novel technique for writing long superstructured fiber Bragg gratings," in Postdeadlin Papers, Photosensitivity and Quadratic Nonlinearity in Glass Waveguides: Fundamentals and Applications, Vol. 22of 1995 Technical Digest Series (Optical Society of America, Washington, D.C., 1995), p. PD 1.
26. Petermann, I.; Sahlgren, B.; Helmfrid, S.; Friberg, A.T. (2002). "Fabrication of advanced fiber Bragg gratings by use of sequential writing with a continuous-wave ultraviolet laser source". Applied Optics. 41 (6): 1051–1056. Bibcode:2002ApOpt..41.1051P. doi:10.1364/ao.41.001051. PMID   11900123.
27. Arkhipov S.V.; Grehn M.; Varzhel S.V.; Strigalev V.E.; Griga N.; Eichler H.J. (2015). "Point-by-point inscription of fiber Bragg gratings into birefringent optical fiber through protective acrylate coating by Ti:Sa femtosecond laser". Scientific and Technical Journal of Information Technologies, Mechanics and Optics. 15 (3): 373–377. doi: 10.17586/2226-1494-2015-15-3-373-377 .
28. Othonos, Andreas; Kalli, Kyriacos (1999). Fiber Bragg Gratings: Fundamentals and Applications in Telecommunications and Sensing. Artech House. ISBN   978-0-89006-344-6.
29. P. Ferraro; G. De Natale (2002). "On the possible use of optical fiber Bragg gratings as strain sensors for geodynamical monitoring". Optics and Lasers in Engineering. 37 (2–3): 115–130. Bibcode:2002OptLE..37..115F. doi:10.1016/S0143-8166(01)00141-5.
30. USpatent 5493390,"Integrated optical instrumentation for the diagnostics of parts by embedded or surface attached optical sensors",issued Feb. 20, 1996 
31. USpatent 5399854,J.R. Dunphy&et al.,"Embedded optical sensor capable of strain and temperature measurement using a single diffraction grating",issued March 21, 1995 
32. Jeong, Y.; Sahu, J.K.; Payne, D.N.; Nilsson, J. (2004). "Ytterbium-doped large-core fiber laser with 1kW continuous-wave output power". Electronics Letters. 40 (8): 470–472. doi:10.1049/el:20040298. PMID   19488250.
33. Xiao, Y.; Brunet, F.; Kanskar, M.; Faucher, M.; Wetter, A.; Holehouse, N. (2012). "1-kilowatt CW all-fiber laser oscillator pumped with wavelength-beam-combined diode stacks". Optics Express. 20 (3): 3296–3301. Bibcode:2012OExpr..20.3296X. doi: 10.1364/oe.20.003296 . PMID   22330567.
34. Dawson, J.W.; Messerly, M.J.; Beach, R.J.; Shverdin, M.Y.; Stappaerts, E.A.; Sridharan, A.K.; Pax, P.H.; Heebner, J.E.; Siders, C.W.; Barty, C.J.P. (2008). "Analysis of the scalability of diffraction-limited fiber lasers and amplifiers to high average power". Optics Express. 16 (17): 13240–13260. Bibcode:2008OExpr..1613240D. doi: 10.1364/oe.16.013240 . PMID   18711562.
35. Oulundsen, G., Farley, K., Abramczyk, J. and Wei, K. "Fiber for fiber lasers: Matching active and passive fibers improves fiber laser performance", Laser Focus World, Vol 48 Jan 2012. http://www.nufern.com/library/item/id/391/
36. Samson, B.; Carter, A.; Tankala, K. (2011). "Rare-earth fibres power up". Nature Photonics. 5 (8): 466–467. Bibcode:2011NaPho...5..466S. doi:10.1038/nphoton.2011.170.

External links

• FOSNE Archived August 25, 2009, at the Wayback Machine - Fibre Optic Sensing Network Europe
• Bragg gratings in Subsea infrastructure monitoring