Jim Kelley Amplifiers

Last updated
1984 Reverb Model in flame maple Jim Kelley Amplifier Reverb Model.jpg
1984 Reverb Model in flame maple

Jim Kelley Amplifiers is the trademark for the vacuum tube guitar amplifiers designed by Jim Kelley and manufactured by his company Active Guitar Electronics of Tustin, California between the years of 1978 and 1985. [1] Approximately 600 of these amps were built during that time. [2] The single-channel version of the amplifier employed modest gain in the preamp stages, Baxandall type bass and treble controls, a split load phase inverter, and four 6V6GT output tubes. [3] [4] The amplifiers produce 60 watts RMS at full power, and include a half power (30/60) switch.

Contents

An improved version of the single-channel amp was released in 1980 which included reverb, an additional stage of gain, and optional foot switchable gain boost. These guitar amps were the first to employ a matched quartet of Sylvania 6V6GT output tubes. The amps were offered with hardwood cabinets, or in a variety of vinyl-covered birch plywood cabinets in a variety of colors. The amps were built as 1-12", or 1-10" combos, or as a head. JBL E-120 speakers were offered as an option.

Jim Kelley Amplifiers were also the first guitar amplifiers to be offered with an optional power attenuator. [5] Jim developed these high-power continuously variable L-pad attenuators as a means of controlling the overall volume of his amplifiers so that the output section could be overdriven at more modest sound pressure levels. One unique feature of these power attenuators is the remote footswitch which would allow the attenuator to be bypassed.

Further amplifier innovations were incorporated into the FACS (foot-activated channel switching) model, which built upon the single-channel design by including two similar switchable preamps and tone stacks, independent reverb level controls for each channel, and internal relay switching for the external power attenuator. These models were available with optional transformer-coupled effects loops, and were configured for either a master effects loop, or for a separate effects loop for each channel. Owing to its longer (22-inch) chassis, the FACS model amplifiers were available additionally as a 2-10", or 4-10" combo. Another novel feature developed by Jim Kelley was the LED Bias Indicator as an aid in adjusting grid bias. [6] [7]

The final model to be developed and produced was the FACS Line Amp. It had all the features of a FACS amp, but the lead channel also employed a low-power push-pull output section. The miniature output transformer was followed by the Main Gain control, which functioned as a Master Volume. The lead channel also had a post distortion passive LC tone control which could cut or boost mid-range.

A rack-mounted, all-FET stereo guitar amplifier with analog delay reverb was developed but never brought to market. [8]

From 2012 until 2017 Suhr Guitars (JS Technologies) reissued the single-channel Reverb Model and Power Attenuator under a licensing agreement with Jim Kelley. [9]

In 2018 Jim began building a new single channel version of the Line Amp model in limited quantities from his own shop. The amps are now only sold at privately held online auctions. The most distinguishing feature of the new design is the innovative Harmonics Generator overdrive circuit. The circuit comprises a dual cascode differential amplifier and utilizes a pair of conventional dual triode tubes. The circuit produces harmonic distortion similar to that of an overdriven power output stage. Like the earlier Line Amps, output signal level is controlled by the Main Gain master volume. A post master volume, transformer coupled, guitar level effects loop is also provided. [10] In addition, the amp contains much of the same circuitry as the original Single Channel non-reverb amp.

In 2020 Jim Kelley began building a two channel version of the Line Amp. Unlike the FACS Line Amp, these amps feature two distinct inputs. But similar to the FACS, the two channel Line Amp has two preamps, and each preamp has its own tone controls. The A input is a legacy Reverb Model preamp. The B input is the Line Amp channel. Channel switching is accomplished using any external A/B or A/B/Y type footswitch. Among the unique feature of these amps are the dual concentric potentiometers, providing control of Gain, Treble, and Bass for each of the two channels.

Related Research Articles

<span class="mw-page-title-main">Guitar amplifier</span> Electronic amplifier for musical instruments

A guitar amplifier is an electronic device or system that strengthens the electrical signal from a pickup on an electric guitar, bass guitar, or acoustic guitar so that it can produce sound through one or more loudspeakers, which are typically housed in a wooden cabinet. A guitar amplifier may be a standalone wood or metal cabinet that contains only the power amplifier circuits, requiring the use of a separate speaker cabinet–or it may be a "combo" amplifier, which contains both the amplifier and one or more speakers in a wooden cabinet. There is a wide range of sizes and power ratings for guitar amplifiers, from small, lightweight "practice amplifiers" with a single 6-inch speaker and a 10-watt amp to heavy combo amps with four 10-inch or four 12-inch speakers and a 100-watt amplifier, which are loud enough to use in a nightclub or bar performance.

<span class="mw-page-title-main">DI unit</span> Audio signal conversion device

A DI unit is an electronic device typically used in recording studios and in sound reinforcement systems to connect a high-output impedance, line level, unbalanced output signal to a low-impedance, microphone level, balanced input, usually via an XLR connector and XLR cable. DIs are frequently used to connect an electric guitar or electric bass to a mixing console's microphone input jack. The DI performs level matching, balancing, and either active buffering or passive impedance matching/impedance bridging to minimize unwanted noise, distortion, and ground loops. DI units are typically metal boxes with input and output jacks and, for more expensive units, “ground lift” and attenuator switches.

<span class="mw-page-title-main">Marshall Amplification</span> British company

Marshall is a British company that designs and manufactures music amplifiers, speaker cabinets, brands personal headphones and earphones, drums and bongos. The company also owns a record label called Marshall Records. It was founded in London by drum shop owner and drummer, Jim Marshall, and is now based in Bletchley, Milton Keynes, England.

<span class="mw-page-title-main">Vox AC30</span> Guitar amplifier

The Vox AC30 is a guitar amplifier manufactured by Vox. It was introduced in 1958 to meet the growing demand for louder amplifiers. Characterised by its "jangly" high-end sound it has become widely recognized by British musicians and others, such as George Harrison and John Lennon of the Beatles, Bill Wyman of the Rolling Stones, Brian May of Queen, Dave Davies of the Kinks and Hank Marvin.

<span class="mw-page-title-main">Bass amplifier</span> Electronic amplifier for musical instruments

A bass amplifier is a musical instrument electronic device that uses electrical power to make lower-pitched instruments such as the bass guitar or double bass loud enough to be heard by the performers and audience. Bass amps typically consist of a preamplifier, tone controls, a power amplifier and one or more loudspeakers ("drivers") in a cabinet.

<span class="mw-page-title-main">Distortion (music)</span> Electronic manipulation of audio to increase gain

Distortion and overdrive are forms of audio signal processing used to alter the sound of amplified electric musical instruments, usually by increasing their gain, producing a "fuzzy", "growling", or "gritty" tone. Distortion is most commonly used with the electric guitar, but may also be used with other electric instruments such as electric bass, electric piano, synthesizer and Hammond organ. Guitarists playing electric blues originally obtained an overdriven sound by turning up their vacuum tube-powered guitar amplifiers to high volumes, which caused the signal to distort. While overdriven tube amps are still used to obtain overdrive, especially in genres like blues and rockabilly, a number of other ways to produce distortion have been developed since the 1960s, such as distortion effect pedals. The growling tone of a distorted electric guitar is a key part of many genres, including blues and many rock music genres, notably hard rock, punk rock, hardcore punk, acid rock, and heavy metal music, while the use of distorted bass has been essential in a genre of hip hop music and alternative hip hop known as "SoundCloud rap".

<span class="mw-page-title-main">Fender Twin</span> Guitar amplifier

The Fender Twin and Twin Reverb are guitar amplifiers made by Fender Musical Instruments Corporation. The Twin was introduced in 1952, two years before Fender began selling Stratocaster electric guitars. The amps are known for their characteristically clean tone.

AHED was a Canadian company owned by Phil G. Anderson that produced guitar amplifiers, as well as guitars. Its main product line was the GBX amplifier, which could reach 180 watts with 4x10", 4x12" or 2x15" speakers. The GBX amplifier had a pre-amplifier that could change the gain, brilliance, depth, contour and response of the output.

<span class="mw-page-title-main">Fender Hot Rod Deluxe</span>

The Fender Hot Rod Deluxe is a guitar amplifier manufactured and sold by the Fender Musical Instruments Corporation. It was introduced in 1996 as part of the "Hot Rod" line of guitar amplifiers and has been in continuous production since. The Hot Rod Deluxe is a modified version of the Fender Blues Deluxe from the earlier Blues line of amplifiers, and has a higher level of gain in its preamplification signal. This model, along with the Hot Rod Deville, were originally designated as F.A.T. amplifiers but this moniker was dropped in 2002 when production of this series of amps was moved from Corona, CA to Fender's Baja-Ensenada, Mexico manufacturing facility.

<span class="mw-page-title-main">Fender Hot Rod DeVille</span> Guitar amplifier

The Fender Hot Rod DeVille is a combo tube guitar amplifier manufactured and sold by Fender. It was introduced in 1996 as part of Fender's Hot Rod line of amplifiers, and since then has been in continuous production. The Hot Rod DeVille is a modified version of the earlier Fender Blues DeVille from the Blues amplifier line, and has a higher level of gain in its preamplification signal. The DeVille incorporates a 60 watt amplifier, and is available in two different models: a 212, which includes a pair of Celestion A-Type 12" speakers, and the 410, which includes four 10" speakers. The DeVille is the sister amplifier of the Fender Hot Rod Deluxe.

The Fender Concert was a guitar amplifier made by Fender Musical Instruments. Its production can be split over 2 phases. The first of these running from 1960 and until approximately 1965, at which time a typical Fender Concert was priced at $315. During the 1960s, the Concert was for all practical purposes the same amplifier as the Vibrasonic but with four 10" speakers. In a later phase, the Concert was updated by Paul Rivera in the early 1980s and a subsequent 1x12 variant of the Concert amp appeared briefly in the mid-1990s.

<span class="mw-page-title-main">Fender Champ</span>

The Fender Champ was a guitar amplifier made by Fender. It was introduced in 1948 and discontinued in 1982. An updated version was introduced in 2006 as part of the "Vintage Modified" line.

The Fender Bandmaster Reverb was a tube amplifier made by Fender. It was primarily a Silverface Bandmaster piggyback 'head' with the addition of reverb and vibrato and a modified circuit that shared more similarities with other Fender amplifiers. It was introduced in 1968 and was discontinued in 1980 .The Bandmaster Reverb was produced in both a 40 watt and 70 watt tube variant, before being reissued as a vintage modified amplifier.

<span class="mw-page-title-main">Fender Princeton</span>

The Fender Princeton was a guitar amplifier made by Fender. It was introduced in 1946 and discontinued in 1979. After Fender introduced the Champ Amp in 1948, the Princeton occupied the next to the bottom spot in the Fender line. Fender Princetons from the early models into the 1970s models are highly valued particularly as recording amplifiers.

<span class="mw-page-title-main">Fender Super</span>

The Fender Super was a guitar amplifier made by Fender between 1947 and 1963 and, as the Super Reverb, until 1981. Though it was designed for a clean sound, its overdriven sound is praised by players and critics.

The Peavey 5150 is a vacuum tube based guitar amplifier made by Peavey Electronics from 1992 on. The amplifier was initially created as a signature model for Eddie Van Halen. After Van Halen and Peavey parted ways in 2004, the name was changed to Peavey 6505. The 5150 name was used again by Van Halen in partnership with Fender under the EVH brand. Peavey's amplifier was renamed to 6505 in celebration of Peavey's 40th anniversary (1965–2005).

<span class="mw-page-title-main">Mesa/Boogie Mark Series</span>

The Mesa/Boogie Mark Series is a series of guitar amplifier made by Mesa Engineering. Originally just referred to as "Boogies," the product line took on the moniker "Mark Series" as newer revisions were put into production. The Mark Series amplifier was Mesa's flagship product until the introduction of the Rectifier series, and the amplifiers are collectable.

The Fender Deluxe guitar amplifier is a range of non-reverb guitar amplifiers produced by Fender. The amplifiers were originally produced from early 1948 to 1966 and reissues are in current production. Its predecessor was the Fender Model 26 "Woodie" produced from 1946 to 1948.

<span class="mw-page-title-main">Fender Vibroverb</span>

The Fender Vibroverb was a 40-watt combo guitar amplifier originally manufactured in 1963 and 1964. It was the first Fender amplifier to incorporate on-board reverb and tremolo/vibrato, which became a standard feature on many high-end Fender tube amps during the 1960s and 1970s.

<span class="mw-page-title-main">Peavey Classic 30 112</span> Guitar amplifier

The Peavey Classic 30 112 is a guitar amplifier produced by Peavey Electronics. It is a tube amplifier designed for Blues, Country and Rock musicians. The Classic 30 112 is a member of the Classic Series family of amplifiers. The amps are known for their durability, flexibility, and tone. Earlier models were dressed in black tolex, while more recent models are dressed in a diagonal tweed material.

References

  1. "Jim Kelley Amplifiers" . Retrieved March 25, 2010.
  2. "Corrections", Guitar Player, NewBay Media, vol. 40, no. 5, May 2006
  3. O'Connor, Kevin (2004). The Ultimate Tone. Power Press. ISBN   0-9698608-9-7.
  4. Brosnac, Donald (2004). The Amp Book. The Bold Strummer. ISBN   0-933224-05-2.
  5. Pittman, Aspen (2003). The Tube Amp Book. Hal Leonard. ISBN   0-87930-767-6.
  6. "Product Profile: Jim Kelley FACS Amp", Guitar Player, NewBay Media, p. 118, June 1983
  7. Thompson, Art (March 2006), "Artifacts: Jim Kelley Amplifiers", Guitar Player, NewBay Media, vol. 40, no. 3, pp. 118–119
  8. "Jim Kelley Amplifiers" . Retrieved March 25, 2010.
  9. "Suhr Guitars" . Retrieved April 18, 2014.
  10. Hunter, Dave (July 2019), "Test Drive: Jim Kelley Line Amp", Vintage Guitar Magazine, Alan Greenwood, vol. 33, no. 9, p. 50

Further reading