The KTM 300 is a series of 2-strokeenduro / off-road motorcycles made by KTM. They are the Penton-inspired 1984 300 GS, the 300 DMX, the dirt only 300 MXC, European road legal 300 EXC and the US 300 XC (close-ratio), 300 XC-W (wide-ratio gear box) and 300 SX (Motocross) versions. The KTM 300 is designed for difficult off-road conditions. The 300 EXC and the 300 XC-W have a small headlight, speedometer, tail-light and somewhat softer linkless PDS[note 1] suspension. Starting in 2008 all 300's came with electric start. Since the early 2000s KTM has been offering the XC-W model in a special "Six-Days" or "ERZBERGRODEO" limited edition.
The original 300GS Enduro grew out of the experience with 250cc Penton Hare Scrambler and other KTM air cooled 2-stroke enduro bikes. Since the 1986 rules for the International Six Days Enduro (ISDE) for the open class allowed any bike larger than 250cc, KTM experimented with a water cooled over-250cc bike for the open class. They essentially bored their 250 out to 273cc and called it a 300. This version of the 300 was discontinued in 1987. KTM also tried sleeving down their 500mxc two-stroke to 350cc calling it the 350mxc, but the left side kick-starter and the right side chain were not popular.[1][2]
1990–1997
In 1990 KTM got serious and the present-day 300 was born.[1] Dubbed the 300 EX/C, its engine delivered very smooth power and did not produce a power hit. The bike performed well at low RPMs. In the mid-range and the top-end the smooth power delivery allowed the rider control over a wide variety of riding conditions from tight trails to wide open stretches. The plush suspension worked well compared to the older GS models.[3]
The bike was also offered as the 300 DMX, a California desert version. These early KTM motors had 297cc displacement with 72mm x 73mm bore/stroke. Still the 300 hadn't reached its full potential. Ignition and jetting problems plagued these early models. In 1992 the company suffered financial woes and development was slowed.[1] The 1993 KTMs had Öhlins USD[note 2] forks. WP forks were also used that year. In 1993 Motoplat went out of business, forcing KTM to switch to SEM ignition systems.[4] The 1996 model had Marzocchi USD forks and an Öhlins rear shock absorber, a chrome exhaust pipe and silencer, a motor with better performance, increased cooling and stock Boyesen reeds. For 1996–97 the bike was offered in a 360cc version. In 1997 KTM switched to Kokusan ignition systems.[1]
1998–2003
1996 was the first year for the KTM trademark orange bikes. In addition to larger capacity radiators, the 300 received KTM’s PDS link-less rear suspension with 320mm of rear wheel travel. The bike was again offered in a bored out 380cc version during 1998-2000 (a street legal title was offered in some states). In 1999 the 300 received a hydraulic clutch and the 2000 motor benefited from a redesigned cylinder.
2004–2007
In 2004 there was another frame change. There were significant engine changes, including a bore and stroke change and the carburetor size reduced from 38mm to 36mm, resulting in an 8lb (3.6kg) weight savings and no more jetting problems.[1] For 2006, the US version of the 300 EXC was replaced by the XC and the XC-W. Both versions had 5-speed gearboxes and a stator for producing electricity. The 300 XC had a close-ratio gear box, no wiring for lights, and a stiffer suspension. The 300 XC-W had a wide-ratio gear box, head light, tail light and maintained the softer PDS suspension. The 2007 model had added a dual ignition mapping switch on the handlebar.
2008–2016
The 2008 KTM 300 EXC is the first electric start two-stroke enduro bike to be released by a major manufacturer. All models have PDS rear suspension.
For 2010, Husaberg the other KTM owned bike company, offered the TE300, an XC-W with minor modifications to the bodywork and suspension settings.
In 2011, models received 6-speed gearboxes, a new exhaust pipe and silencer, and translucent fuel tanks. The XC was also upgraded to a new frame, while retaining PDS rear suspension. These frame updates did not make it to the XC-W until 2012. The 2011 Husaberg TE 300 was essentially a rebadged KTM 300 and was available through 2012.
In 2012 there were improvements to the starter motor bendix, more frame changes resulting in more wheel travel for models with PDS rear suspension (except the XC),[5] and a new air box with a filter that can be replaced without the use of tools. The 300XC was changed from PDS rear suspension to linkage rear suspension.[6] The 300XC-W models received the frame and bodywork updates that arrived in the XC line the year before, but also retain PDS rear suspension.
In 2013 the clutch was changed to a 'DDS' diaphragm spring clutch with lighter pull, a new stronger starter motor (350W motor was replaced with a 410W motor), lighter battery, and triple clamps changed from 22mm to 20mm offset. The Husaberg TE300 was rebranded the Husqvarna TE300 and also received linkage rear suspension.
In 2014 bikes received a new CDI unit and ignition curve, stronger/larger battery, changed jetting, updated brakes (front master cylinder, caliper, and pads changed), a redesigned cylinder head, new Boyesen reeds, stiffer seat foam, and a new rear shock absorber with revised settings.
The 2015 model chromoly steel frame is painted orange like the motocross models. All the 2015 models have the new WP 4CS forks with revised damping (rebound in one fork and compression in the other) with the ability to make adjustments on the fly, and a smaller front axle. The triple clamps have 2mm less offset resulting in more trail and different steering characteristics. The rear shock is longer but the travel is unchanged. The electric starter has different gearing to provide higher initial torque from the electric motor, and the battery is lighter and stronger.[7][8][2]
2017–2022
KTM 300 XC-W Six-Days Spain Edition
The 2017 KTM 300's are completely redesigned bikes with new engines. A lateral counter-balancer has been added to greatly reduce motor vibration. The cases are a new design featuring a new position for the starter motor. A Mikuni TMX38 carb replaced the Keihin PWK carburetor as Keihin focuses on fuel injection. There was a change to the air filter design. Suspension changed with the addition of a new Xplor 48 frok and rear shock, which was downsized from 50mm to 46mm. The forks are similar to the previous generation open cartridge forks supplied on the 300's with split compression and rebound adjusters on separate fork legs. The adjuster atop the left fork controls compression and adjuster top the right fork controls rebound similar to the 4CS fork system (However, the internals are otherwise quite different than 4CS).
For 2018 KTM started offering the 300 EXC (Europe only) model with transfer port injection (TPI) and with oil injection through the 39mm Dell’Orto throttle body to meet EURO 4 standards.[9][10] In the U.S., the 2018 XC-W was offered in a TPI alongside the existing Mikuni version.
For 2019 KTM began offering U.S. customers the 300 XC-W model with (TPI) and oil injection. The fuel injected 300's were previously available only in the international market. The KTM XC-W still comes with PDS rear suspension while the 300 XC and the Husqvarna TC300 (essentially a KTM XC with different plastics and subframe) and the TE300 come with linkage rear suspension.
For the 2020 model year KTM began providing U.S. customers both the 300 XC-W and 300 XC with TPI and throttle body oil injection, thus eliminating all carbureted 300's from the US market. Both models benefit from updated EFI mapping and a new added air pressure sensor. [11] The XC-W was given an all new chassis positioning the motor one degree downward for better front end handling. Minor changes include: An updated ECU, suspension settings and styling / plastic upgrades.[12]
For 2021 there was little change. The GasGas EC and EX models incorporated TPI features of each the KTM and Husqvarna 300's. The expansion chamber design was updated using a new manufacturing process to produce a ribbed stamped design that reduces noise and increases strength and impact resistance. The shape is also adjusted for improved ground clearance. The silencer was also updated to a new design that is more compact and has an integrated aluminum mounting bracket. On a side note the 2021s were the last KTM 2-strokes eligible for a California red/green sticker.
In November 2020 KTM released new '102' ECU maps that improve fueling and responsiveness, and an optional '103 Extreme Mapping' for 2020-2021 250/300 TPI bikes that adjust fueling and increase oiling. [13]
KTM 300Notable Changes
2017
Counter balancer added , Mikuni TMX38 Carb, New air box/filter
2018
Transfer Port Injection added to 300 for Euro bikes only. 250 XC-W TPI offered in the U.S. 1st year of the ERZBERGRODEO edition.
2019
TPI only for 300 XC-W
2020
TPI all models, Improved ignition mapping, re-designed plastics.
2021
Pleated/ribbed expansion chamber, new piston, new throttle assembly.
2022
Nitrated steel liners in the clutch for improved life and better heat resistance.
2023–Present
In 2023 KTM introduced an all new motor for the 300XC and 300SX lines. The new motor employs Throttle Body Injection in place of the previous Transfer Port Injecton as well as an electronic power valve in place of the mechanical one. The new XC and SX bikes do away with the oil pump and oil reservoir requiring the use of pre-mix gas. The kick starter option has been completely eliminated, electric start only. The 2023 300XC-W maintained the previous engine design with TPI and the kick start option. [14]
For 2024 KTM completed the transition from TPI to TBI on all versions of the 300. The 2024 300XC-W retains the oil pump and oil tank making it easy to fill-up with pump gas.
Notes
↑ PDS is an initialism for Progressive Damping System when referring to rear shock absorbers in non-linkage rear suspensions."
↑ USD is an initialism for UpSide Down when referring to telescopic forks on modern motorcycles."
KTM AG is an Austrian motorcycle, bicycle and sports car manufacturer owned by Pierer Mobility AG and the Indian manufacturer Bajaj Auto. It was formed in 1992 but traces its foundation to as early as 1934. Today, KTM AG is the parent company of the KTM Group, consisting of a number of motorcycle brands.
The Honda XR series is a range of four-stroke off-road motorcycles that were designed in Japan but assembled all over the world.
Maicowerk A.G., known by its trading name Maico is the name of a family company in the Swabian town of Pfäffingen near Tübingen. Founded in 1926 by Ulrich Maisch as Maisch & Co, the company originally manufactured 98 and 123 cc Ilo two-stroke engines. After World War II, they began producing their own unit construction two-stroke engines, selling complete motorcycles. Maico made a brief foray into the automobile business with their own line of microcars in the late 1950s. Maico have also made go kart engines.
Husaberg was a manufacturer of enduro motorcycles with four and two-stroke engines, the displacements ranging from 125 cc to 650 cc. Originally based in Sweden, its motorcycles were later manufactured in Austria by parent company KTM until the line was retired in 2014.
The Yamaha WR450F is an off-road motorcycle made by Yamaha Motor Company. It currently has a 450 cc (27 cu in) liquid-cooled single-cylinder engine. First offered in 1998 at 400cc, it shared many components and design concepts with the YZ400F motocross model. It is basically the racing YZ450F detuned slightly for more controllable power, with a headlight and lighting coil, softer suspension, a kickstand, lower noise specifications, larger radiators and lower emissions. The WR in the name indicates a wide-ratio gear box common to most enduro or trail bikes and stands in contrast to the close-ratio gearbox essential to a motocross racer. Over the years the WR has benefited from the advances made in the YZ motocross version gaining displacement and advancements such as an aluminum frame and improved suspension. Over much of its life the weight of the WR450F has remained fairly constant ranging from 244 to 249 pounds dry weight.
An enduro motorcycle is an off-road racing motorcycle used in enduros, which are long-distance cross-country, Trails, time trial competitions.
Beta is an Italian motorcycle manufacturer, specialising in off-road motorcycles. Beta are best known for their popular observed trials bikes. In 2005, they launched a range of enduro motorcycles using KTM engines. In 2010 they launched the new RR series, with a new engine made in-house. Beta motorcycles have been used by world trials champions such as Jordi Tarrés, Dougie Lampkin, Albert Cabestany and Enduro riders Steve Holcombe and Brad Freeman. Production in 2018 was expected to be in excess of 20,000 motorcycles, ranging in size from 50 cc to 480 cc.
The Honda XR250R and XR250L are trail and dual-sport motorcycles made by Honda from 1979 through 2004, as part of the Honda XR series. They have four-stroke, SOHC four-valve 249 cc (15.2 cu in) single-cylinder engines.
The Yamaha YZ450F is a four-stroke racing motocross bike built by Yamaha Motor Corporation. It was the successor to the previous YZ426F which was discontinued in 2003. It is credited by Cycle World and Dirt Rider magazines as the bike that started the four-stroke dirt bike revolution. The 2006 YZ250F and YZ450F were the first production motorcycles equipped with titanium suspension springs.
Motorcycle components and systems for a motorcycle are engineered, manufactured, and assembled in order to produce motorcycle models with the desired performance, aesthetics, and cost. The key components of modern motorcycles are presented below.
Husqvarna Motorcycles GmbH is a Swedish-origin Austrian company which designs, engineers, manufactures and distributes motocross, enduro, supermoto and street motorcycles.
The KTM 450 EXC is a 4-stroke enduro off-road motorcycle made by KTM. The models are the European road legal 400 EXC and 450 EXC, the US 450 XC and 450 XC-W. The European EXC versions have a small headlight, speedometer, tail-light and somewhat softer linkless (PDS) rear suspension. The US EXC is 50-states street legal.
The Kawasaki KR-1 and KR-1S are road-orientated 249 cc (15.2 cu in) two-stroke sports bikes introduced between 1988 and 1992 by Kawasaki Heavy Industries.
The "Pure Enduro" series of off-road racing motorcycles ran from 1977 through to 1984 in engine displacements from 175cc through 400cc. All engines were case-reed valve, air-cooled, two-stroke and single-cylinder with plain steel bores. Lubrication was provided via 20:1 pre-mix. These were directly related to the Suzuki RM series range of motocross racers.
The KTM 500 EXC is one model in the series of 4-stroke enduro off-road motorcycle made by KTM. They are essentially the 400/450 EXCs with changes to the stroke to achieve larger displacements. The 520, 525, 530 and 500 are all in fact 510.4 cc motors given different model numbers to distinguish them. Like the other KTM enduro offerings they vary in the set-up and components. The international EXC versions have a small headlight, speedometer, tail-light and somewhat softer linkless (PDS) rear suspension. 2007 was the first year the EXC was deemed street legal in the US. As of 2008 the US version of the EXC, with the new XC-4 motor, continued to be sold in street legal trim. In 2012 the US 50-states street legal 530 EXC-R was rebadged the 500 EXC. In mid 2016 the 2017 bikes were introduced adding a 250cc version. It joins the 350 and 500 EXC-F.
The KTM 200 consists of a series of two-stroke off-road enduro motorcycles made by KTM, the European, road legal 200 EXC, and the 200 XC-W for the US market being the last versions. The 200 attempts to combine the agility of a 125 cc class motorcycle with the power of a 250 cc. As a small bore enduro bike it is equipped with a wide-ratio gear box. Starting in 2013 all 200's came with electric start.
The Kawasaki KX 449F is a liquid-cooled DOHC 449 cc (27.4 cu in) four-valve four-stroke single motocross motorcycle made by Kawasaki.
The KTM 950 Super Enduro R is a dual-sport motorcycle produced from 2006 to 2008. It is equipped with a 98-horsepower, four-stroke, V-twin engine, adjustable heavy-duty offroad suspension, and enduro styling. Due to its light weight and offroad-capable profile, the 950SE was perceived at its launch as a radical departure from any existing dual-sport, enduro, or street bike models, while having characteristics of all three.
Royal Enfield Classic 350 and Classic 500 are models of Royal Enfield motorcycles which have been in production since 2009. The Classic series of Royal Enfield motorcycles are inspired by the Royal Enfield G2 350cc Bullet motorcycle, first produced in 1948.
The G450X is an Enduro-class motorcycle that was produced by BMW Motorrad between 2008 and 2011.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
