LB&SCR C2 class

Last updated

LB&SCR C2 class
2436 at Brighton 1948.jpg
C2 class 2436 at Brighton in 1948.
Type and origin
Power typeSteam
Designer R. J. Billinton
rebuilt D. E. Marsh
Builder Vulcan Foundry
Serial number1375–1386, 1412–1419, 1699–1718, 1813–1827
Build date1893–1902
Total produced55
Rebuild date1908–1940
Specifications
Configuration:
​
 •  Whyte 0-6-0
Gauge 4 ft 8+1⁄2 in (1,435 mm) standard gauge
Driver dia.5 ft 0 in (1.524 m)
Wheelbase 16 ft 0 in (4.88 m)
Loco weight38 long tons (38.6 t; 42.6 short tons); C2 class
45 long tons (45.7 t; 50.4 short tons) C2X class
Fuel type Coal
Water cap.2,420 imp gal (11,002 L; 2,906 US gal)
Boiler pressure160  psi (1.10  MPa) C2 class
170 psi (1.17 MPa) C2X class
Cylinders Two, inside
Cylinder size 17.5 in × 26 in (444 mm × 660 mm)
Performance figures
Tractive effort 18,050  lbf (80.3  kN) C2 class
19,175 lbf (85.3 kN) C2X class
Career
Operators
Power class2F
Withdrawn1935–1950 C2 class
1957-1962 C2X class
DispositionAll Scrapped

The London, Brighton and South Coast Railway C2 class was a class of 0-6-0 steam locomotives, intended for heavy freight trains. Fifty-five were built by the Vulcan Foundry between 1893 and 1902 to the design of Robert J. Billinton. Forty-five of these were later rebuilt between 1908 and 1940, with a larger boiler as the C2X class.

Contents

C2 class

In January 1891, Robert Billinton was given authority to build ten new 0-6-0 freight locomotives, to supplement William Stroudley's C1 class of 1882-7. However, at the time, Brighton railway works was fully committed building Billinton's various classes of radial tanks and so tenders were sought from outside contractors. Ultimately the Vulcan Foundry agreed to construct these ten locomotives, and further orders were received at intervals until 55 had been purchased by February 1902. The class were therefore nicknamed 'Vulcans'. [1]

The new class were not as powerful as their predecessors but were found to be both reliable and also capable of running at speed, thereby enabling them to be used on secondary passenger and excursion duties. [2] As a result, a further ten were ordered from Vulcan Foundry, which were delivered 1893-4, and twenty five delivered 1900-1902.

C2X class

C2X 32449 at Bricklayers' Arms 1958 Deptford near North Kent West Junction geograph-2658568-by-Ben-Brooksbank.jpg
C2X 32449 at Bricklayers' Arms 1958
32532, with double dome, at Three Bridges Depot 11 December 1948 Three Bridges Locomotive Depot Large Vulcan geograph-2980375-by-Ben-Brooksbank.jpg
32532, with double dome, at Three Bridges Depot 11 December 1948

During the first decade of the twentieth century the railway experienced a rapid growth in freight traffic and by 1905 their locomotives were no longer capable of hauling the heaviest trains without loss of time. Douglas Earle Marsh's initial response was to introduce his C3 class with a larger boiler in 1906, but the performance of these also proved to be disappointing.

However, in 1908 Marsh rebuilt one C2 with a larger diameter C3 steel boiler and an extended smokebox. [1] In doing so he created an excellent powerful freight locomotive that was classified "C2X", and nicknamed 'Large Vulcans.' The modification was so successful that twenty-nine out of the original fifty-five members of the class were similarly rebuilt by the end of 1912. [3] By this time the class were beginning to struggle to keep time when hauling the heaviest freight trains and began to be superseded on these by the K class 2-6-0 in 1913/14, but were nevertheless kept very busy during the First World War on military supply and munitions trains, and three further C2’s had been rebuilt by the end of 1922.

After the First World War Lawson Billinton acquired ten spare boilers for the class incorporating his own top feed apparatus. These were clearly visible when fitted because of the presence of a second dome. [4]

Grouping and Nationalisation

All of the C2 and C2X locomotives passed to the Southern Railway in 1923, and nine further examples were rebuilt during 1924-5, as the original boilers became due for replacement. However, the trade recession of the early 1930s caused a decline in freight traffic resulting in the withdrawal of seven of the remaining C2 locomotives by the end of 1937. The advent of the Second World War meant that four other survivors were rebuilt in 1939 and 1940 and that the remaining three unrebuilt C2 locomotives remained in service until after the nationalisation of the railways to British Railways in 1948. Those remaining were all withdrawn between 1948 and 1950.

The C2X locomotives remained in regular use on secondary freight trains for a further decade and most had completed very impressive mileages for freight locomotives before they were all withdrawn between 1957 and February 1962. The last two examples were based at Three Bridges and Brighton and had completed 1,340,578 mi (2,157,451 km) and 1,279,527 mi (2,059,199 km) respectively. [5]

No examples have been preserved.

Accidents and incidents

Locomotive Summary

Related Research Articles

<span class="mw-page-title-main">BR Standard Class 4 2-6-4T</span>

The British Railways Standard Class 4 tank is a class of steam locomotive, one of the BR standard classes built during the 1950s. They were used primarily on commuter and outer suburban services. They were capable of reaching speeds of 75 mph (121 km/h).

<span class="mw-page-title-main">WD Austerity 2-8-0</span>

The War Department (WD) "Austerity" 2-8-0 is a type of heavy freight steam locomotive that was introduced in 1943 for war service. A total of 935 were built, making this one of the most-produced classes of British steam locomotive. They were nicknamed Ozzies by the railwaymen.

<span class="mw-page-title-main">LNER Class V2</span>

The London and North Eastern Railway (LNER) Class V2 2-6-2 steam locomotives were designed by Sir Nigel Gresley for express mixed traffic work, and built at the LNER shops at Doncaster and Darlington between 1936 and 1944. The best known is the first of the class, 4771 Green Arrow, which is the sole survivor of the class.

<span class="mw-page-title-main">LNER Thompson Class B1</span>

The London and North Eastern Railway (LNER) Thompson Class B1 is a class of steam locomotive designed by Edward Thompson for medium mixed traffic work.

<span class="mw-page-title-main">NER 1001 Class</span>

The North Eastern Railway (NER) 1001 Class was a class of long-boiler 0-6-0 steam locomotive originally designed by William Bouch for the Stockton and Darlington Railway.

<span class="mw-page-title-main">Brighton railway works</span>

Brighton railway works was one of the earliest railway-owned locomotive repair works, founded in 1840 by the London and Brighton Railway in Brighton, England, and thus pre-dating the more famous railway works at Crewe, Doncaster and Swindon. The works grew steadily between 1841 and 1900 but efficient operation was always hampered by the restricted site, and there were several plans to close it and move the facility elsewhere. Nevertheless, between 1852 and 1957 more than 1200 steam locomotives as well as prototype diesel electric and electric locomotives were constructed there, before the eventual closure of the facility in 1962.

<span class="mw-page-title-main">LB&SCR B1 class</span>

The London, Brighton and South Coast Railway B1 Class is a class of 0-4-2 express passenger steam locomotives, known from the name of the first, No. 214, as the "Gladstones".

<span class="mw-page-title-main">NER Class P3</span>

The North Eastern Railway (NER) Class P3, classified J27 by the LNER, is a class of 0-6-0 steam locomotive. The P3 Class was designed by Wilson Worsdell and was a relatively minor modification of the existing North Eastern Railway Class P2. The most significant change was a deeper firebox with shallower sloping fire grate. This was achieved by raising the boiler slightly, and by reducing the clearance between the firebox and the rear axle. The P3 Class were a freight engine by nature and used for hauling long trains of freight.

<span class="mw-page-title-main">LB&SCR B4 class</span>

The B4 class were 4-4-0 steam locomotives for express passenger work on the London, Brighton and South Coast Railway. They were designed by R. J. Billinton and were either built at Brighton works 1899–1902 or else by Messrs Sharp, Stewart and Company in 1901. Twelve members of the class were rebuilt from 1922 to 1924 by L. B. Billinton with a larger boiler, cylinders and a superheater. The rebuilt locomotives were classified B4X.

<span class="mw-page-title-main">GNR Class C1 (large boiler)</span> Type of locomotive

The Great Northern Railway (GNR) Class C1 is a type of 4-4-2 steam locomotive. One, ex GNR 251, survives in preservation. Much like their small boiler cousins, they were capable of reaching speeds of up to 90 mph (145 km/h). They were also known as Large Atlantics.

<span class="mw-page-title-main">LB&SCR K class</span> Class of mixed traffic steam engines

The LB&SCR K class were powerful 2-6-0 mixed traffic locomotives designed by L. B. Billinton for the London, Brighton and South Coast Railway (LB&SCR) in 1913. They appeared shortly before the First World War and the first ten examples of the class did prodigious work during that conflict on munitions, supply and troop trains. Further examples were built after the war, and the class was used as a test bed for various items of specialised equipment. However, after the formation of the Southern Railway in 1923 the remaining three locomotives on order were not completed and the seventeen members of the class led relatively quiet yet reliable lives over their traditional lines. The locomotives proved their usefulness once again during the Second World War, and continued to provide reliable service until the 1960s. The entire class was eventually withdrawn in 1962 for 'bookkeeping' rather than 'operational' reasons.

<span class="mw-page-title-main">Cocking railway station</span> Former railway station in England

Cocking Railway Station served the village of Cocking in West Sussex, England. It was on the former London Brighton and South Coast Railway line between Chichester and Midhurst. The station was designed by T. H. Myres, in his standardized Domestic Revival style, each formed like a large "Country House", similar to the stations on the Bluebell Railway.

<span class="mw-page-title-main">LB&SCR D1 class</span>

The LB&SCR D1 class were powerful 0-4-2 suburban passenger tank locomotives, designed by William Stroudley of the London Brighton and South Coast Railway in 1873. They were originally known as "D-tanks" but later reclassified as class D1. Members of this very successful class survived in service until 1951.

The North Eastern Railway Class S2 - London and North Eastern Railway Class B15 - was a mixed-traffic 4-6-0 steam locomotive designed by Vincent Raven. The design was based on NER Class S.

<span class="mw-page-title-main">LB&SCR B2 class</span>

The London, Brighton and South Coast Railway (LB&SCR) B2 class was a class of small 4-4-0 steam locomotives intended for express passenger work on the LB&SCR London to Portsmouth line. They were designed by R. J. Billinton and built at Brighton works from 1895 to 1897. They proved to be reliable locomotives but barely adequate for the heaviest trains and acquired the nickname Grasshoppers. As a result the B3 class was developed from the B2, and the B2X class was later rebuilt from these locomotives with larger boilers.

<span class="mw-page-title-main">LB&SCR E5 class</span>

The London, Brighton and South Coast Railway E5 class was a class of 0-6-2T side tank steam locomotive designed by Robert Billinton. They were introduced in 1902 and were a larger version of the E4 Class intended for semi-fast secondary passenger work.

<span class="mw-page-title-main">LB&SCR E6 class</span>

The London, Brighton and South Coast Railway E6 class was a class of 0-6-2T side tank steam locomotive designed by Robert Billinton. They were introduced in 1904 and were a development of the E5 class with smaller driving wheels intended for heavy short and medium-distance freight trains.

<span class="mw-page-title-main">LB&SCR C3 class</span>

The London, Brighton and South Coast Railway C3 class was a class of 0-6-0 steam locomotives, intended for heavy freight trains. Ten were built by Brighton railway works in 1906 to the design of Douglas Earle Marsh.

<span class="mw-page-title-main">LB&SCR I3 class</span>

The LB&SCR I3 class was a class of 4-4-2 steam tank locomotives designed by D. E. Marsh for suburban passenger service on the London, Brighton and South Coast Railway.

<span class="mw-page-title-main">SECR E class</span>

The SECR E class was a class of 4-4-0 tender locomotives designed by Harry Wainwright for express passenger trains on the South Eastern and Chatham Railway. It was a larger version of the D class incorporating a Belpaire firebox

References

  1. 1 2 Bixley, Gerry (2010). "The LBSCR C2 and C2X goods engines". The Southern Way (9): 6–21. ISBN   9781906419288.
  2. ↑ Bradley, D.L. (1974). Locomotives of the London Brighton and South Coast Railway, Part 3. Railway Correspondence and Travel Society. p. 97.
  3. ↑ Bradley, D.L. (1972). Locomotives of the London Brighton and South Coast Railway, Part 2. Railway Correspondence and Travel Society. pp. 97–108.
  4. ↑ Bradley (1974), p.103.
  5. ↑ Bradley (1972) p.108.
  6. ↑ Hoole, Ken (1982). Trains in Trouble: Vol. 3. Redruth: Atlantic Books. p. 22. ISBN   0-906899-05-2.
  7. ↑ Bradley, (1972), p.102.
  8. ↑ "BOMB DAMAGE AT WORTHING ROAD OCTOBER 1940 (HORSHAM - CHRIST'S HOSPITAL)". THE SUSSEX MOTIVE POWER DEPOTS. Retrieved 6 October 2020.
  9. ↑ Hoole, Ken (1983). Trains in Trouble: Vol. 4. Redruth: Atlantic Books. pp. 25, 40. ISBN   0-906899-07-9.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.