Mission type | Earth imaging |
---|---|
Operator | NASA |
COSPAR ID | 1978-026A [1] |
SATCAT no. | 10702 [1] |
Mission duration | 5 years, 6 months, 2 days |
Spacecraft properties | |
Bus | Nimbus |
Manufacturer | GE Aerospace |
Launch mass | 960.0 kilograms (2,116.4 lb) |
Start of mission | |
Launch date | March 5, 1978 |
Rocket | Delta 2910 |
Launch site | Vandenberg AFB SLC-2W |
End of mission | |
Deactivated | September 7, 1983 |
Orbital parameters | |
Reference system | Geocentric |
Regime | Sun-synchronous |
Perigee altitude | 818 kilometers (508 mi) |
Apogee altitude | 918 kilometers (570 mi) |
Inclination | 99.1 degrees |
Period | 103.16 minutes |
Epoch | May 15, 1990 [1] |
Landsat 3 is the third satellite of the Landsat program. It was launched on March 5, 1978, with the primary goal of providing a global archive of satellite imagery. Unlike later Landsat satellites, Landsat 3 was managed solely by NASA. Landsat 3 decommissioned on September 7, 1983, beyond its design life of one year. [2] The data collected during Landsat 3's lifetime was used by 31 countries. Countries that cannot afford their own satellite are able to use the data for ecological preservation efforts and to determine the location of natural resources.
The first satellite of the Landsat program, Landsat 1 (originally designated ERTA-1), took and transmitted over 100,000 photos during its lifetime. [3]
Landsat 3 (originally designated Landsat C) was the third satellite launched as a part of the Landsat program, and the last Landsat satellite managed by NASA. [2] The satellite had a very similar designs to Landsat 1 and Landsat 2. [4]
Landsat 3 was built by GE Aerospace. [2] The objective of Landsat 3 was to extend the period of space data acquisition for Earth resources by Landsat 1 and Landsat 2. Landsat 3 was to obtain information on agricultural and forestry resources, geology and mineral resources, hydrology and water resources, geography, cartography, environmental pollution, oceanography and marine resources, and meteorological phenomena. [5]
The spacecraft used an attitude control system (ACS) with freon gas as the propellant. Combined with horizon scanners, Sun sensors, and a command antenna, the ACS was able to control the spacecraft in all three axes to plus or minus one degree. [5]
The satellite also carried two wide-band video tape recorders (WBVTR) capable of storing up to 30 minutes of scanner or camera data, giving the spacecraft's sensors a near-global coverage capability. [2] Video was transmitted back to Earth in both real time and from the recorders at 2265.5 MHz. [5]
The satellite was also equipped with a data collection system (DCS) to collect information from remote, individually equipped ground stations and to relay the data to central acquisition stations. The DCS was composed of three different collection methods. The first was the data collection platforms (DCPs), which could consist of ocean buoys, constant pressure balloons, or automatic ground stations. The second was the satellite equipment, and the third the ground data centers. Due to the orbit of the satellite, data could be obtained at a minimum of every 12 hours. No data processing or signal multiplexing occurred on the satellite. [6] The design of the DCS came from the Nimbus-3 platform, then known as the interrogation, recording, and location system (IRLS). [4]
Landsat 3 carried a Multispectral Scanner, built by Hughes Aircraft Corporation. The sensor weighed 64 kilograms (141 lb), required 50 W of power, and had a maximum 75 meters (246 ft) resolution. [4] It was made up of a double reflector telescope, scanning mirror, and detectors. The primary mission of the MSS was to obtain data for agriculture, forestry, geology, and hydrology, but the MSS could also collect information for oceanography and meteorology purposes. [7]
The MSS had five spectral bands, which is one more than Landsat 1 and 2. Each spectral band had different scientific uses. Band 4 primarily investigated areas of water, with the ability to detect sediment laden areas and areas of shallow water. Band 5 was primarily used to identify cultural features. Band 6 sensed the vegetation boundaries between land, water, and landforms. Band 7 was the most proficient at sensing through atmospheric haze, and identified water and land boundaries, vegetation, and landforms. [8] The scene size for the scanners of the MSS was 170 kilometers (110 mi) to 185 km (115 mi), which is the area the sensors could survey per scan. The ground sampling interval of the MSS was 57 m (187 ft) to 79 m (259 ft), which is medium resolution. [9] [8] Unlike the previous two Landsat missions, a thermal band was built into Landsat 3's MSS, but this instrument failed shortly after the satellite was deployed on July 11, 1978. [10] The thermal band would have enabled the MSS to have remote sensing capabilities during the night. [7]
The Return Beam Vidicon (RBV) was designed at RCA in Princeton, New Jersey. [4] It contained two cameras to cover the 0.53 to 0.75 micrometer spectral band. The cameras were structurally isolated from the satellite so that they could maintain their alignment. Each camera was triggered every 12.5 seconds so that the images would overlap in the direction the spacecraft was moving. The cameras each had a 98 kilometers (61 mi) square viewing range, and combined the range was 185 km (115 mi). The cameras contained an optical lens, RBV sensor, thermoelectric cooler, deflection and focus coils, a mechanical shutter, and erase lamps. Landsat 3's RBV had a resolution of 40 meters (130 ft), which was twice the resolution of Landsat 1's 80 m (260 ft). [11]
The 960 kilograms (2,120 lb) Landsat 3 was launched from Vandenberg Air Force Base, California on March 5, 1978. [12] [13] It was placed into a Sun-synchronous, near polar orbit at an inclination of 99.1 degrees and an altitude of 570 miles (920 km). Landsat 3 completed 14 orbits of the Earth daily, and its cycle repeated every 18 days. [2]
Landsat 3's MSS had five spectral bands, but one failed shortly after launch. The satellite was placed in standby mode on March 31, 1983. [2] Landsat 3 was decommissioned on September 7, 1983. [10]
The data from Landsat 3 was used by over 400 programs in 31 countries. Countries that could not afford their own satellite used the data to discover and monitor resources that they would have not been capable of otherwise. For example, Bolivia spent $10,000 on data which was used to discover vast lithium deposits, while United States companies have invested more than $136 million for further exploration. Kenya used the data to monitor grazing conditions and to help lion and cheetah preservation efforts, and Pakistan used the data to decide where to dredge the river delta to build a new port. [14]
Specific locations for Landsat 3's data can be found by using the World Reference System (WRS). To find any specific location on Earth, a row and path number are required; for example, Row 60 is at the equator. Landsat 1-3 use WRS-1, but Landsats 4 and after used WRS-2. [4]
The Landsat program is the longest-running enterprise for acquisition of satellite imagery of Earth. It is a joint NASA / USGS program. On 23 July 1972, the Earth Resources Technology Satellite was launched. This was eventually renamed to Landsat 1 in 1975. The most recent, Landsat 9, was launched on 27 September 2021.
Landsat 1 (LS-1), formerly named ERTS-A and ERTS-1, was the first satellite of the United States' Landsat program. It was a modified version of the Nimbus 4 meteorological satellite and was launched on July 23, 1972, by a Delta 900 rocket from Vandenberg Air Force Base in California.
Landsat 7 is the seventh satellite of the Landsat program. Launched on 15 April 1999, Landsat 7's primary goal is to refresh the global archive of satellite photos, providing up-to-date and cloud-free images. The Landsat program is managed and operated by the United States Geological Survey, and data from Landsat 7 is collected and distributed by the USGS. The NASA WorldWind project allows 3D images from Landsat 7 and other sources to be freely navigated and viewed from any angle. The satellite's companion, Earth Observing-1, trailed by one minute and followed the same orbital characteristics, but in 2011 its fuel was depleted and EO-1's orbit began to degrade. Landsat 7 was built by Lockheed Martin Space Systems.
Landsat 6, equipped with upgraded versions of the instruments on Landsat 5, was designed to carry forward the Landsat program. It was launched on October 5, 1993, with a Titan II launch vehicle, but failed to reach orbit. Landsat 6 omitted the Multi-Spectral Scanner found on its predecessors, but carried an Enhanced Thematic Mapper, which improved on the previous Thematic Mapper by adding a 15m-resolution panchromatic band.
Landsat 5 was a low Earth orbit satellite launched on March 1, 1984, to collect imagery of the surface of Earth. A continuation of the Landsat Program, Landsat 5 was jointly managed by the U.S. Geological Survey (USGS) and the National Aeronautics and Space Administration (NASA). Data from Landsat 5 was collected and distributed from the USGS's Center for Earth Resources Observation and Science (EROS).
Landsat 4 is the fourth satellite of the Landsat program. It was launched on July 16, 1982, with the primary goal of providing a global archive of satellite imagery. Although the Landsat Program is managed by NASA, data from Landsat 4 was collected and distributed by the U.S. Geological Survey. Landsat 4 science operations ended on December 14, 1993, when the satellite lost its ability to transmit science data, far beyond its designed life expectancy of five years. The satellite housekeeping telemetry and tracking continued to be maintained by NASA until it was decommissioned on June 15, 2001.
Resourcesat-1 is an advanced remote sensing satellite built by Indian Space Research Organization (ISRO). The tenth satellite of ISRO in IRS series, Resourcesat-1 is intended to not only continue the remote sensing data services provided by IRS-1C and IRS-1D, both of which have far outlived their designed mission lives, but also vastly enhance the data quality.
Landsat 2 is the second satellite of the Landsat program. The spacecraft originally carried a designation of ERTS-B but was renamed "Landsat 2" prior to its launch on January 22, 1975. The objective of the satellite was to acquire global, seasonal data in medium resolution from a near-polar, Sun-synchronous orbit. The satellite, built by General Electric, acquired data with the Return Beam Vidicon (RBV) and the Multispectral Scanner (MSS). Despite having a design life of one year, Landsat 2 operated for over seven years, finally ceasing operations on February 25, 1982.
NOAA-18, also known as NOAA-N before launch, is an operational, polar orbiting, weather satellite series operated by the National Environmental Satellite Service (NESS) of the National Oceanic and Atmospheric Administration (NOAA). NOAA-18 also continued the series of Advanced TIROS-N (ATN) spacecraft begun with the launch of NOAA-8 (NOAA-E) in 1983 but with additional new and improved instrumentation over the NOAA A-M series and a new launch vehicle. NOAA-18 is in an afternoon equator-crossing orbit and replaced NOAA-17 as the prime afternoon spacecraft.
Landsat 8 is an American Earth observation satellite launched on 11 February 2013. It is the eighth satellite in the Landsat program; the seventh to reach orbit successfully. Originally called the Landsat Data Continuity Mission (LDCM), it is a collaboration between NASA and the United States Geological Survey (USGS). NASA Goddard Space Flight Center in Greenbelt, Maryland, provided development, mission systems engineering, and acquisition of the launch vehicle while the USGS provided for development of the ground systems and will conduct on-going mission operations. It comprises the camera of the Operational Land Imager (OLI) and the Thermal Infrared Sensor (TIRS), which can be used to study Earth surface temperature and is used to study global warming.
NOAA-13, also known as NOAA-I before launch, was an American weather satellite operated by the National Oceanic and Atmospheric Administration (NOAA). NOAA-I continued the operational, polar orbiting, meteorological satellite series operated by the National Environmental Satellite System (NESS) of the National Oceanic and Atmospheric Administration (NOAA). NOAA-I continued the series (fifth) of Advanced TIROS-N (ATN) spacecraft begun with the launch of NOAA-8 (NOAA-E) in 1983. NOAA-I was in an afternoon equator-crossing orbit and was intended to replace the NOAA-11 (NOAA-H) as the prime afternoon (14:00) spacecraft.
The Operational Land Imager (OLI) is a remote sensing instrument aboard Landsat 8, built by Ball Aerospace & Technologies. Landsat 8 is the successor to Landsat 7 and was launched on February 11, 2013.
UNIFORM-1 or University International Formation Mission is a Japanese micro-satellite launched in 2014. The satellite is built around a wildfire detection camera and features the following instruments:
Landsat 9 is an Earth observation satellite launched on 27 September 2021 from Space Launch Complex-3E at Vandenberg Space Force Base on an Atlas V 401 launch vehicle. NASA is in charge of building, launching, and testing the satellite, while the United States Geological Survey (USGS) operates the satellite, and manages and distributes the data archive. It is the ninth satellite in the Landsat program, but Landsat 6 failed to reach orbit. The Critical Design Review (CDR) was completed by NASA in April 2018, and Northrop Grumman Innovation Systems (NGIS) was given the go-ahead to manufacture the satellite.
Nimbus 1 was a meteorological satellite. It was the first in a series of the Nimbus program.
Nimbus 2 was a meteorological satellite. It was the second in a series of the Nimbus program.
NOAA-10, known as NOAA-G before launch, was an American weather satellite operated by the National Oceanic and Atmospheric Administration (NOAA) for use in the National Environmental Satellite Data and Information Service (NESDIS). It was the third of the Advanced TIROS-N series of satellites. The satellite design provided an economical and stable Sun-synchronous platform for advanced operational instruments to measure the atmosphere of Earth, its surface and cloud cover, and the near-space environment.
NOAA-12, also known as NOAA-D before launch, was an American weather satellite operated by National Oceanic and Atmospheric Administration (NOAA), an operational meteorological satellite for use in the National Environmental Satellite, Data, and Information Service (NESDIS). The satellite design provided an economical and stable Sun-synchronous platform for advanced operational instruments to measure the atmosphere of Earth, its surface and cloud cover, and the near-space environment.
NOAA-14, also known as NOAA-J before launch, was an American weather satellite operated by the National Oceanic and Atmospheric Administration (NOAA). NOAA-14 continued the third-generation operational, Polar Orbiting Environmental Satellite (POES) series operated by the National Environmental Satellite Service (NESS) of the National Oceanic and Atmospheric Administration (NOAA). NOAA-14 continued the series of Advanced TIROS-N (ATN) spacecraft begun with the launch of NOAA-8 (NOAA-E) in 1983.