 | This article needs additional citations for verification .(August 2014) (Learn how and when to remove this template message) |
There are several uses of the 2.4 GHz band. Interference may occur between devices operating at 2.4 GHz. This article details the different users of the 2.4 GHz band, how they cause interference to other users and how they are prone to interference from other users.
Many of the cordless telephones and baby monitors in the United States and Canada use the 2.4 GHz frequency, the same frequency at which Wi-Fi standards 802.11b, 802.11g and 802.11n operate. This can cause a significant decrease in speed, or sometimes the total blocking of the Wi-Fi signal when a conversation on the phone takes place. There are several ways to avoid this however, some simple, and some more complicated.
A cordless telephone or portable telephone is a telephone in which the handset is portable and communicates with the body of the phone by radio, instead of being attached by a cord. The base station is connected to the telephone network through a telephone line as a corded telephone is, and also serves as a charger to charge the handset's batteries. The range is limited, usually to the same building or some short distance from the base station.
A baby monitor, also known as a baby alarm, is a radio system used to remotely listen to sounds made by an infant. An audio monitor consists of a transmitter unit, equipped with a microphone, placed near to the child. It transmits the sounds by radio waves to a receiver unit with a speaker carried by, or near to, the person caring for the infant. Some baby monitors provide two-way communication which allows the parent to speak back to the baby. Some allow music to be played to the child. A monitor with a video camera and receiver is often called a baby cam.
The United States of America (USA), commonly known as the United States or America, is a country composed of 50 states, a federal district, five major self-governing territories, and various possessions. At 3.8 million square miles, the United States is the world's third or fourth largest country by total area and is slightly smaller than the entire continent of Europe's 3.9 million square miles. With a population of over 327 million people, the U.S. is the third most populous country. The capital is Washington, D.C., and the largest city by population is New York City. Forty-eight states and the capital's federal district are contiguous in North America between Canada and Mexico. The State of Alaska is in the northwest corner of North America, bordered by Canada to the east and across the Bering Strait from Russia to the west. The State of Hawaii is an archipelago in the mid-Pacific Ocean. The U.S. territories are scattered about the Pacific Ocean and the Caribbean Sea, stretching across nine official time zones. The extremely diverse geography, climate, and wildlife of the United States make it one of the world's 17 megadiverse countries.
The last will sometimes not be successful, as numerous cordless phones use a feature called Digital Spread Spectrum. This technology was designed to ward off eavesdroppers, but the phone will change channels at random, leaving no Wi-Fi channel safe from phone interference.
Bluetooth devices intended for use in short-range personal area networks operate from 2.4 to 2.4835 GHz. To reduce interference with other protocols that use the 2.45 GHz band, the Bluetooth protocol divides the band into 80 channels (numbered from 0 to 79, each 1 MHz wide) and changes channels up to 1600 times per second. Newer Bluetooth versions also feature Adaptive Frequency Hopping which attempts to detect existing signals in the ISM band, such as Wi-Fi channels, and avoid them by negotiating a channel map between the communicating Bluetooth devices.
Bluetooth is a wireless technology standard for exchanging data between fixed and mobile devices over short distances using short-wavelength UHF radio waves in the industrial, scientific and medical radio bands, from 2.400 to 2.485 GHz, and building personal area networks (PANs). It was originally conceived as a wireless alternative to RS-232 data cables.
A personal area network (PAN) is a computer network for interconnecting devices centered on an individual person's workspace. A PAN provides data transmission among devices such as computers, smartphones, tablets and personal digital assistants. PANs can be used for communication among the personal devices themselves, or for connecting to a higher level network and the Internet where one master device takes up the role as gateway. A PAN may be wireless or carried over wired interfaces such as USB.
The industrial, scientific and medical (ISM) radio bands are radio bands reserved internationally for the use of radio frequency (RF) energy for industrial, scientific and medical purposes other than telecommunications. Examples of applications in these bands include radio-frequency process heating, microwave ovens, and medical diathermy machines. The powerful emissions of these devices can create electromagnetic interference and disrupt radio communication using the same frequency, so these devices were limited to certain bands of frequencies. In general, communications equipment operating in these bands must tolerate any interference generated by ISM applications, and users have no regulatory protection from ISM device operation.
The USB 3.0 computer cable standard has been proven to generate significant amounts of electromagnetic interference that can interfere with any Bluetooth devices a user has connected to the same computer. [1] Various strategies can be applied to resolve the problem, ranging from simple solutions such as increasing the distance of USB 3.0 devices from any Bluetooth devices to purchasing better shielded USB cables. [2]
 The old Wi-Fi Alliance logo | |
| Introduced | September 1998 |
|---|---|
| Compatible hardware | Personal computers, gaming consoles, televisions, printers, mobile phones |
Wi-Fi ( /ˈwaɪfaɪ/ ) [3] is technology for radio wireless local area networking of devices based on the IEEE 802.11 standards. Wi‑Fi is a trademark of the Wi-Fi Alliance, which restricts the use of the term Wi-Fi Certified to products that successfully complete interoperability certification testing. [4]
Devices that can use Wi-Fi technologies include desktops and laptops, video game consoles, smartphones and tablets, smart TVs, digital audio players, cars and modern printers. Wi-Fi compatible devices can connect to the Internet via a WLAN and a wireless access point. Such an access point (or hotspot) has a range of about 20 meters (66 feet) indoors and a greater range outdoors. Hotspot coverage can be as small as a single room with walls that block radio waves, or as large as many square kilometres achieved by using multiple overlapping access points.
Different versions of Wi-Fi exist, with different ranges, radio bands and speeds. Wi-Fi most commonly uses the 2.4 gigahertz (12 cm) UHF and 5.8 gigahertz (5 cm) SHF ISM radio bands; these bands are subdivided into multiple channels. Each channel can be time-shared by multiple networks. These wavelengths work best for line-of-sight. Many common materials absorb or reflect them, which further restricts range, but can tend to help minimise interference between different networks in crowded environments. At close range, some versions of Wi-Fi, running on suitable hardware, can achieve speeds of over 1 Gbit/s.
Anyone within range with a wireless network interface controller can attempt to access a network; because of this, Wi-Fi is more vulnerable to attack (called eavesdropping) than wired networks. Wi-Fi Protected Access (WPA) is a family of technologies created to protect information moving across Wi-Fi networks and includes solutions for personal and enterprise networks. Security features of WPA have included stronger protections and new security practices as the security landscape has changed over time.
To guarantee no interference in any circumstances the Wi-Fi protocol requires 16.25 to 22 MHz of channel separation (as shown below). The remaining 2 MHz gap is used as a guard band to allow sufficient attenuation along the edge channels. This guardband is mainly used to accommodate older routers with modem chipsets prone to full channel occupancy, as most modern WiFi modems are not prone to excessive channel occupancy.
While overlapping frequencies can be configured and will usually work, it can cause interference resulting in slowdowns, sometimes severe, particularly in heavy use. Certain subsets of frequencies can be used simultaneously at any one location without interference (see diagrams for typical allocations):
However, the exact spacing required when the transmitters are not colocated depends on the protocol, the data rate selected, the distances and the electromagnetic environment where the equipment is used. [5]
| Channel separation: | 0 | 1 | 2 | 3 | 4 | 5 |
|---|---|---|---|---|---|---|
| Attenuation (dB) | 0 | 0.3 - 0.6 | 1.8 - 2.5 | 6.6 - 8.2 | 23.5 - 35 | 49.9 - 53.2 |
The attenuation by relative channel adds to that due to distance. Per the standards, for transmitters on the same channel, transmitters must take turns to transmit if they can detect each other 3 dB above the noise floor. On the other hand, transmitters will ignore transmitters on other channels if the attenuated signal strength from them is below a threshold Pth which is between -76 and -80 dBm. [6]
While there can be interference (bit errors) at a receiver, this is usually small if the received signal is more than 20 dB above the attenuated signal strength from transmitters on the other channels. [6]
The overall effect is that if there is considerable overlap between adjacent channels transmitters they will often interfere with each other. However, using every fourth or fifth channel by leaving three or four channels clear between used channels can cause less interference than sharing channels, and narrower spacing still can be used at further distances. [7] [5]
Certain car manufacturers use the 2.4 GHz frequency for their car alarm internal movement sensors. These devices transmit on 2.45 GHz (between channels 8 and 9) at a strength of 500 mW. Because of channel overlap, this will cause problems for channels 6 and 11, which are commonly used default channels for Wi-Fi connections. Because the signal is transmitted as a continuous tone, it causes particular problems for Wi-Fi traffic. This can be clearly seen with spectrum analysers. These devices, due to their short range and high power, are typically not susceptible to interference from other devices on the 2.4 GHz band.[ citation needed ]
Microwave ovens operate by emitting a very high power signal in the 2.4 GHz band. Older devices have poor shielding,[ citation needed ] and often emit a very "dirty" signal over the entire 2.4 GHz band.
This can cause considerable difficulties to Wi-Fi and video[ citation needed ] transmission, resulting in reduced range or complete blocking of the signal.
The IEEE 802.11 committee that developed the Wi-Fi specification conducted an extensive investigation into the interference potential of microwave ovens. A typical microwave oven uses a self-oscillating vacuum power tube called a magnetron and a high voltage power supply with a half wave rectifier (often with voltage doubling) and no DC filtering. This produces an RF pulse train with a duty cycle below 50% as the tube is completely off for half of every AC mains cycle: 8.33 ms in 60 Hz countries and 10 ms in 50 Hz countries.
This property gave rise to a Wi-Fi "microwave oven interference robustness" mode that segments larger data frames into fragments each small enough to fit into the oven's "off" periods.
The 802.11 committee also found that although the instantaneous frequency of a microwave oven magnetron varies widely over each half AC cycle with the instantaneous supply voltage, at any instant it is relatively coherent, i.e., it occupies only a narrow bandwidth. [8] The 802.11a/g signal is inherently robust against such interference because it uses OFDM with error correction information interleaved across the carriers; as long as only a few carriers are wiped out by strong narrow band interference, the information in them can be regenerated by the error correcting code from the carriers that do get through.
Video senders typically operate using an FM carrier to carry a video signal from one room to another (for example, satellite TV or closed-circuit television). These devices typically operate continuously but have low (10 mW) transmit power. However, some devices, especially wireless cameras, operate with (often unauthorized) high power levels, and have high-gain antennas.[ citation needed ]
Amateur Radio operators can transmit two-way Amateur television (and voice) in the 2.4 GHz band - and all ISM frequencies above 902 MHz - with maximum power of 1500 watts in the US if the transmission mode does not include spread spectrum techniques. [9] [10] Other power levels apply per regions. In the UK, the maximum power level for a full licence is 400 watts. [11] In other countries, maximum power level for non - spread spectrum emissions are set by local legislation. [ citation needed ]
Although the transmitter of some video cameras appears to be fixed on one frequency, it has been found in several models that the cameras are actually frequency agile, and can have their frequency changed by disassembling the product and moving solder links or dip switches inside the camera.
These devices are prone to interference from other 2.4 GHz devices, due to the nature of an analog video signal showing up interference very easily. A carrier to noise ratio of some 20 dB is required to give a "clean" picture.
Continuous transmissions interfere with these, causing "patterning" on the picture, sometimes a dark or light shift, or complete blocking of the signal.
Non-continuous transmissions, such as Wi-Fi, cause horizontal noise bars to appear on the screen, and can cause "popping" or "clicking" to be heard in the audio.
Video senders are a big problem for Wi-Fi networks. Unlike Wi-Fi they operate continuously, and are typically only 10 MHz in bandwidth. This causes a very intense signal as viewed on a spectrum analyser, and completely obliterates over half a channel. The result of this, typically in a Wireless Internet service provider-type environment, is that clients (who cannot hear the video sender due to the "hidden node" effect) can hear the Wi-Fi without any issues, but the receiver on the WISP's access point is completely obliterated by the video sender, so is extremely deaf. Furthermore, due to the nature of video senders, they are not interfered with by Wi-Fi easily, since the receiver and transmitter are typically located very close together, so the capture effect is very high. Wi-Fi also has a very wide spectrum, so only typically 30% of the peak power of the Wi-Fi actually affects the video sender. Wi-Fi is not continuous transmit, so the Wi-Fi signal interferes only intermittently with the video sender. A combination of these factors - low power output of the Wi-Fi compared to the video sender, the fact that typically the video sender is far closer to the receiver than the Wi-Fi transmitter and the FM capture effect means that a video sender may cause problems to Wi-Fi over a wide area, but the Wi-Fi unit causes few problems to the video sender.[ citation needed ]
Many video senders on the market in the UK advertise a 100 mW equivalent isotropically radiated power (EIRP). However, the UK market only permits a 10 mW EIRP limit. These devices cause far more interference across a far wider area, due to their excessive power. Furthermore, UK video senders are required to operate across a 20 MHz bandwidth (not to be confused with 20 MHz deviation). This means that some foreign imported video senders are not legal since they operate on a 15 MHz bandwidth or lower, which causes a higher spectral power density, increasing the interference. Furthermore, most other countries permit 100 mW EIRP for video senders, meaning a lot of video senders in the UK have excessive power outputs.[ citation needed ]
Many ZigBee / IEEE 802.15.4-based wireless data networks operate in the 2.4–2.4835 GHz band, and so are subject to interference from other devices operating in that same band. To avoid interference from IEEE 802.11 networks, an IEEE 802.15.4 network can be configured to only use channels 15, 20, 25, and 26, avoiding frequencies used by the commonly used IEEE 802.11 channels 1, 6, and 11.
Wireless Microphones operate as transmitters. Some digital wireless microphones use the 2.4 GHz band (e.g. AKG model DPT 70).
 | This section contains instructions, advice, or how-to content .(January 2013) |
Normally interference is not too hard to find. Products are coming onto the market cheaply which act as spectrum analyzers and use a standard USB interface into a laptop, meaning that the interference source can be fairly easily found with a little work, a directional antenna and driving around to find the interference.
Often solving interference is as simple as changing the channel of the offending device. Particularly with video senders, whereby plugging in the receiver with no transmitter attached will let you "see" the neighbour's video sender, this technique is considered part of the "Installation process". Where the channel of one system, such as a Wireless ISP cannot be changed, and it is being Interfered with by something such as a video sender, the owner of the video sender is normally very happy to assist with doing this, providing it is not too much work. However the problem comes when the interference is something such as a wireless CCTV camera which is mounted on a chimney and requires a long ladder to access. Such cameras, due to their height, cause serious problems across a wide area.
Another cure is to offer an alternative product to the owner free of charge. Typically this would be a wired camera, which normally have far better performance than wireless cameras anyway, a cable to replace the video sender, or an alternative video sender which has been hard-wired to an alternative channel, with no means of changing it back to the offending frequency.
Yet another cure is to move from 2.4 GHz to another frequency which lacks the vulnerability to interference inherent at that frequency, for example the 5 GHz frequency for 802.11a/n.
In extreme cases, where the interference is either deliberate or all attempts to get rid of the offending device have proved futile, it may be possible to look at changing the parameters of the network. Changing collinear antennas for high gain directional dishes normally works very well, since the narrow beam from a high gain dish will not physically "see" the interference. Often sector antennae have sharp "nulls" in their vertical pattern, so changing the tilt angle of sector antennas with a spectrum analyzer connected to monitor the strength of the interference can place the offending device within the null of the sector. High gain antennas on the transmitter end can "overpower" the interference, although their use may cause the effective radiated power (ERP) of the signal to become too high, and so their use may not be legal.
Interference caused by a Wi-Fi network to its neighbors can be reduced by adding more base stations to that network. Every Wi-Fi standard provides for automatic adjustment of the data rate to channel conditions; poor links (usually those spanning greater distances) automatically operate at lower speeds. Deploying additional base stations around the coverage area of a network, particularly in existing areas of poor or no coverage, reduces the average distance between a wireless device and its nearest access point and increases the average speed. The same amount of data takes less time to send, reduces channel occupancy, and gives more idle time to neighboring networks, improving the performance of all networks concerned.
The alternative of increasing coverage by adding an RF power amplifier to a single base station can bring similar improvements to a wireless network. The additional power offered by a linear amplifier will increase the signal-to-noise ratio at the client device, increasing the data rates used and reducing time spent transmitting data. The improved link quality will also reduce the number of retransmissions due to packet loss, further reducing channel occupancy. However, care must be taken to use a highly linear amplifier in order to avoid adding excessive noise to the signal.
All of the base stations in a wireless network should be set to the same SSID (which must be unique to all other networks within range) and plugged into the same logical Ethernet segment (one or more hubs or switches directly connected without IP routers). Wireless clients then automatically select the strongest access point from all those with the specified SSID, handing off from one to another as their relative signal strengths change. On many hardware and software implementations, this hand off can result in a short disruption in data transmission while the client and the new base station establish a connection. This potential disruption should be factored in when designing a network for low-latency services such as VoIP.
IEEE 802.11 is part of the IEEE 802 set of LAN protocols, and specifies the set of media access control (MAC) and physical layer (PHY) protocols for implementing wireless local area network (WLAN) Wi-Fi computer communication in various frequencies, including but not limited to 2.4, 5, and 60 GHz frequency bands.
In telecommunications, orthogonal frequency-division multiplexing (OFDM) is a method of encoding digital data on multiple carrier frequencies. OFDM has developed into a popular scheme for wideband digital communication, used in applications such as digital television and audio broadcasting, DSL internet access, wireless networks, power line networks, and 4G mobile communications.
A wireless network is a computer network that uses wireless data connections between network nodes.
Wi-Fi is technology for radio wireless local area networking of devices based on the IEEE 802.11 standards. Wi‑Fi is a trademark of the Wi-Fi Alliance, which restricts the use of the term Wi-Fi Certified to products that successfully complete, then after many years of testing the 802.11 committee interoperability certification testing.
Ultra high frequency (UHF) is the ITU designation for radio frequencies in the range between 300 megahertz (MHz) and 3 gigahertz (GHz), also known as the decimetre band as the wavelengths range from one meter to one tenth of a meter. Radio waves with frequencies above the UHF band fall into the super-high frequency (SHF) or microwave frequency range. Lower frequency signals fall into the VHF or lower bands. UHF radio waves propagate mainly by line of sight; they are blocked by hills and large buildings although the transmission through building walls is strong enough for indoor reception. They are used for television broadcasting, cell phones, satellite communication including GPS, personal radio services including Wi-Fi and Bluetooth, walkie-talkies, cordless phones, and numerous other applications.
Wireless local loop (WLL), is the use of a wireless communications link as the "last mile / first mile" connection for delivering plain old telephone service (POTS) or Internet access to telecommunications customers. Various types of WLL systems and technologies exist.
WiMAX is a family of wireless broadband communication standards based on the IEEE 802.16 set of standards, which provide multiple physical layer (PHY) and Media Access Control (MAC) options.
The S band is a designation by the Institute of Electrical and Electronics Engineers (IEEE) for a part of the microwave band of the electromagnetic spectrum covering frequencies from 2 to 4 gigahertz (GHz). Thus it crosses the conventional boundary between the UHF and SHF bands at 3.0 GHz. The S band is used by airport surveillance radar for air traffic control, weather radar, surface ship radar, and some communications satellites, especially those used by NASA to communicate with the Space Shuttle and the International Space Station. The 10 cm radar short-band ranges roughly from 1.55 to 5.2 GHz. The S band also contains the 2.4–2.483 GHz ISM band, widely used for low power unlicensed microwave devices such as cordless phones, wireless headphones (Bluetooth), wireless networking (WiFi), garage door openers, keyless vehicle locks, baby monitors as well as for medical diathermy machines and microwave ovens. India’s regional satellite navigation network (IRNSS) broadcasts on 2.483778 to 2.500278 GHz.
Code of Federal Regulations, Title 47, Part 15 is an oft-quoted part of Federal Communications Commission (FCC) rules and regulations regarding unlicensed transmissions. It is a part of Title 47 of the Code of Federal Regulations (CFR), and regulates everything from spurious emissions to unlicensed low-power broadcasting. Nearly every electronics device sold inside the United States radiates unintentional emissions, and must be reviewed to comply with Part 15 before it can be advertised or sold in the US market.
IEEE 802.11n-2009, commonly shortened to 802.11n, is a wireless-networking standard that uses multiple antennas to increase data rates. Wi-Fi Alliance have also labelled the technology for the standard as Wi-Fi 4. It standardized support for multiple-input multiple-output, frame aggregation, and security improvements, among other features, and can be used in the 2.4 GHz or 5 GHz frequency bands.
IEEE 802.11y-2008 is an amendment to the IEEE 802.11-2007 standard that enables data transfer equipment to operate using the 802.11a protocol on a co-primary basis in the 3650 to 3700 MHz band except when near a grandfathered satellite earth station. IEEE 802.11y is only being allowed as a licensed band. It was approved for publication by the IEEE on September 26, 2008.
A video sender is a device for transmitting domestic audio and video signals wirelessly from one location to another. It is most commonly used for sending the output of a source device, such as a satellite television decoder, to a television in another part of a property and provides an alternative to cable installations.
Long-range Wi-Fi is used for low-cost, unregulated point-to-point computer network connections, as an alternative to other fixed wireless, cellular networks or satellite Internet access.
IEEE 802.11a-1999 or 802.11a was an amendment to the IEEE 802.11 wireless local network specifications that defined requirements for an orthogonal frequency division multiplexing (OFDM) communication system. It was originally designed to support wireless communication in the unlicensed national information infrastructure (U-NII) bands as regulated in the United States by the Code of Federal Regulations, Title 47, Section 15.407.
IEEE 802.11b-1999 or 802.11b, is an amendment to the IEEE 802.11 wireless networking specification that extends throughput up to 11 Mbit/s using the same 2.4GHz band. A related amendment was incorporated into the IEEE 802.11-2007 standard.
IEEE 802.11g-2003 or 802.11g is an amendment to the IEEE 802.11 specification that extended throughput to up to 54 Mbit/s using the same 2.4 GHz band as 802.11b. This specification under the marketing name of Wi-Fi has been implemented all over the world. The 802.11g protocol is now Clause 19 of the published IEEE 802.11-2007 standard, and Clause 19 of the published IEEE 802.11-2012 standard.
WiGig, alternatively known as 60GHz Wi-Fi, refers to a set of 60 GHz wireless network protocols. It includes the current IEEE 802.11ad standard and also the upcoming IEEE 802.11ay standard.
IEEE 802.11ah is a wireless networking protocol published in 2017 to be called Wi-Fi HaLow as an amendment of the IEEE 802.11-2007 wireless networking standard. It uses 900 MHz license exempt bands to provide extended range Wi-Fi networks, compared to conventional Wi-Fi networks operating in the 2.4 GHz and 5 GHz bands. It also benefits from lower energy consumption, allowing the creation of large groups of stations or sensors that cooperate to share signals, supporting the concept of the Internet of Things (IoT). The protocol's low power consumption competes with Bluetooth and has the added benefit of higher data rates and wider coverage range.