NE5532

Last updated
A genuine Signetics NE5532N in PDIP package, made in 1990, on a modem board DOV-1X - Signetics NE5532N on printed circuit board-9973.jpg
A genuine Signetics NE5532N in PDIP package, made in 1990, on a modem board
A Texas Instruments SA5532A in SOIC package on an audio distribution amplifier board Kramer Electronics PT-102AN - board - Texas Instruments SA5532A-9848.jpg
A Texas Instruments SA5532A in SOIC package on an audio distribution amplifier board

The NE5532, also sold as SA5532, SE5532 and NG5532 (commonly called just 5532) is a dual monolithic, bipolar, internally compensated operational amplifier (op amp) for audio applications introduced by Signetics in 1979. The 5532 and the contemporary TL072 were the first operational amplifiers that outperformed discrete class A circuits in professional audio applications. Due to low noise and very low distortion, the 5532 became the industry standard for professional audio. [1] [2] According to Douglas Self, "there is probably no music on the planet that has not passed through a hundred or more 5532s on its way to the consumer". [3] The performance of the 5532 remained best in class for almost thirty years, until the introduction of the LM4562 in 2007. [4] As of 2021, the 5532 remains in mass production as a generic product.

Contents

Unlike many other low-cost op amps, the 5532 exists only in a dual form, available in 8-pin PDIP, SO and SOIC packages. The single 5534, as well as the discontinued uncompensated dual 5533, is not fully compensated and is thus unstable at unity gain; the 5534 has lower noise density than the 5532 but is otherwise similar.

History

The op-amp was originally made by Signetics and sold by Philips Semiconductors as TDA1034 and later renamed. [5]

Construction and operation

The 5532 is fully bipolar, with the exception of a sole JFET within a bias generator. Although the manufacturers did not release a first-hand explanation of its operation, the schematic has been public for decades. [6] The signal path consists of two consecutive differential stages, a single-ended common emitter voltage amplification stage, and a class B push-pull output follower with a current-sensing overload protection. [7] There are four internal compensation capacitors. [7] The distortion "signature" (that is, the virtual absence of it) of the 5532 is defined largely by the three nested frequency compensation loops wrapped around the second and the third stages. [7]

Input requirements

The input stage uses NPN transistors, thus the input bias currents flow into their bases, and cause negative voltage drop across the ground-to-input resistance. [8] A typical 200 nA bias current flowing through a typical 47 kOhm resistor, for example, will cause a 10 mV voltage drop. [9] These fairly stable shifts in operating points are usually not a concern. If possible, audio designers would allow them to accumulate over several stages, and then block the accumulated DC offset with a single output capacitor. [10] Bias currents may not be allowed to flow through potentiometers, as it causes excessive crackling noise when the wipers are moved. [11]

The inputs of the 5532 are protected with back-to-back diodes rated for currents up to 10 mA; these may open during fast input signal transients, and cause harsh output distortion. [12] [11] The 5532 is intended for linear operation only, and should not be used as a comparator, or otherwise subjected to large differential input voltages. [11]

A typical 5532 operating from ±15 V supply rails retains linearity as long as the input voltages remains within ±13 V range. When common-mode voltage exceeds +13 V or goes below -13 V, the 5532 clips but remains operational as long as either input stays within the power supply voltages. Input overdrive does not cause output phase inversion which is common to the TL072 op amp. [13]

Power supply requirements

The 5532 stands out among audio op amps in having an unusually high absolute maximum supply voltage rating of 44 V (compared to more common 36 V). [14] In practice, each of the two amplifiers draws a fairly high 4–5 mA supply current, and the plastic package becomes appreciably warm at 34 V supply voltage. [15] According to Douglas Self, using power supplies of more than 34 V is potentially unsafe, and certainly incompatible with most other op amps. [14]

The 5532 is sensitive to power supply AC decoupling; failure to decouple leads to erratic internal high-frequency oscillation that does not propagate to the output directly, but causes apparent distortion. [11] A single 0.1 μF high-quality capacitor, connected across the power supply pins and in close proximity to them, is normally sufficient to prevent such oscillations. [6] The manufacturers recommend using two such capacitors, connected between each power supply pin and the ground; according to Douglas Self, this is not necessary and sometimes undesirable due to the risks of injecting noise currents into the signal ground. [6]

Distortion

The 5532 attains lowest total harmonic distortion (THD) in an inverting (shunt-feedback) configuration with moderate gain and moderate signal levels, where the THD does not exceed 0.0005% throughout the audio frequency spectrum. [16] High source impedances inject added thermal noise, but do not affect the THD of the inverting amplifier. [17] Increasing output level to 10 V does not affect performance through most of the audio frequency, except for the octave above 10 kHz where the THD rises to 0.001%. [17] For comparison, the classic μA741 can deliver the rated 0.001% THD only at frequencies below 100 Hz; above the 100 Hz mark the THD continuously increases, reaching 1% at around 20 kHz. [18]

In the non-inverting (series-feedback) configuration driven with a low-impedance source the 5532 demonstrates mild common-mode distortion. [19] This form of distortion is most prominent at unity gain, but even there THD remains under 0.002% as long as the source impedance does not exceed 2 kOhm. [20] The reported "sweet spot" lies around 1 kOhm source impedance, although this may be dependent on the manufacturer. [20] As source impedances increase to 10 kOhm and beyond, 5532 performance radically worsens. [21] Distortion is now dominated by components that are proportional to the square of common-mode signal voltage. [21] Worst-case THD may exceed 0.02% at the treble end of the audio range. [21]

Noise

The 5532, like all bipolar-input op amps, has significant current and voltage noise densities, typically 5 nV/Hz1/2 and 0.7 pA/Hz1/2, respectively, at 1 kHz. [22] Even accounting for the increase in noise densities at lower frequencies, voltage noise and current noise over the 20 kHz audio bandwidth do not exceed 1 μV and 100 pA, respectively. The three noise components — differential voltage noise referred to inputs, inverting input current and non-inverting input current — are assumed to be uncorrelated with each other. [22] In reality there is some correlation, but its effect is insignificant. [22]

Current and noise densities of the far more expensive bipolar-input OP27 and OP270, as well as the 5534, are only about 2–3 dB lower. [22] The LM4562 has half the voltage noise of the 5532, but more than twice current noise. [22] FET input devices have much higher voltage noise densities but practically nonexistent current noise [23] The extremely low-noise LT1028 is nominally 15 dB quieter than the 5532, but is otherwise poorly suited for audio applications. [24] The choice of the "lowest noise op amp" ultimately depends on which form of noise, voltage noise or current noise, is most critical in a specific application. [23]

NE5534

The 5534 single operational amplifier is schematically identical to one half the 5532, with marginally different values of the internal compensation capacitors. The difference, however, is large enough to decompensate the amplifier. The 5534 is stable only at closed-loop gain of 3 and more. The slew rate is accordingly higher, typically 13 V/μs compared to 9 V/μs of the 5532; the unity gain crossover frequency is also higher, at around 30–50 MHz. [25] The unity gain bandwidth of 10 MHz, same as for the 5532, is quoted for a fully compensated amplifier (implying the use of an external compensation capacitor). The input-referred noise densities are marginally lower. In practical applications, particularly large professional audio consoles, these advantages were not as important as was the added complexity, so the single 5534 did not see as much use as the dual 5532. The third IC in the family, the dual uncompensated 5533, has been long discontinued.

For unity-gain stability, the 5534 requires an external compensation capacitor of at least 22 pF for the non-inverting circuit, and 11 pF or more for the inverting circuit. [25] Compensation inevitably decreases slew rate, compromising response to fast signal transients. This is unimportant in audio equipment, where the worst-case, theoretical slew rate at maximum output swing barely exceeds 2 V/μs. [26] In more demanding applications, stability and high slew rate may be maintained simultaneously with the help of a lead-lag RC network between the 5534 inputs. [25] The corner frequency of lead-lag network is normally selected at around 3–5 MHz, one decade below the unity gain crossover frequency. [27] The regular compensation capacitor must remain, but its value can be safely decreased to 3 pF at unity gain. [27]

Notes

  1. ↑ Self 2010, pp. 95, 115.
  2. ↑ Electronic Musician. Polyphony Publishing Company. 1993. p. 51.
  3. ↑ Self 2010, p. 117.
  4. ↑ Self 2010, pp. 121, 123.
  5. ↑ "Pro Audio Reference". 1034. Retrieved 2024-08-08.
  6. 1 2 3 Self 2010, p. 120.
  7. 1 2 3 Self 2010, pp. 120–121.
  8. ↑ Self 2010, pp. 99, 117, 119.
  9. ↑ Self 2010, pp. 99, 119.
  10. ↑ Self 2010, p. 99.
  11. 1 2 3 4 Self 2010, p. 119.
  12. ↑ Signetics 1987, p. 6.53.
  13. ↑ Self 2010, pp. 117–118.
  14. 1 2 Self 2010, pp. 525.
  15. ↑ Self 2010, p. 119, 525.
  16. ↑ Self 2010, p. 104.
  17. 1 2 Self 2010, p. 105.
  18. ↑ Self 2010, p. 118.
  19. ↑ Self 2010, p. 106.
  20. 1 2 Self 2010, pp. 106–107.
  21. 1 2 3 Self 2010, p. 107.
  22. 1 2 3 4 5 Self 2010, p. 96.
  23. 1 2 Self 2010, p. 97.
  24. ↑ Self 2010, p. 23.
  25. 1 2 3 Signetics 1987, p. 6.54.
  26. ↑ Self 2010, p. 103.
  27. 1 2 Signetics 1987, p. 6.55.

Related Research Articles

<span class="mw-page-title-main">Amplifier</span> Electronic device/component that increases the strength of a signal

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal. It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is defined as a circuit that has a power gain greater than one.

<span class="mw-page-title-main">Operational amplifier</span> High-gain voltage amplifier with a differential input

An operational amplifier is a DC-coupled electronic voltage amplifier with a differential input, a (usually) single-ended output, and an extremely high gain. Its name comes from its original use of performing mathematical operations in analog computers.

<span class="mw-page-title-main">Comparator</span> Device that compares two voltages or currents

In electronics, a comparator is a device that compares two voltages or currents and outputs a digital signal indicating which is larger. It has two analog input terminals and and one binary digital output . The output is ideally

<span class="mw-page-title-main">Valve amplifier</span> Type of electronic amplifier

A valve amplifier or tube amplifier is a type of electronic amplifier that uses vacuum tubes to increase the amplitude or power of a signal. Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers in the 1960s and 1970s. Valve amplifiers can be used for applications such as guitar amplifiers, satellite transponders such as DirecTV and GPS, high quality stereo amplifiers, military applications and very high power radio and UHF television transmitters.

<span class="mw-page-title-main">Buffer amplifier</span> Electronic amplifier, a circuit component

In electronics, a buffer amplifier is a unity gain amplifier that copies a signal from one circuit to another while transforming its electrical impedance to provide a more ideal source. This "buffers" the signal source in the first circuit against being affected by currents from the electrical load of the second circuit and may simply be called a buffer or follower when context is clear.

<span class="mw-page-title-main">Common emitter</span> Type of electronic amplifier using a bipolar junction transistor

In electronics, a common-emitter amplifier is one of three basic single-stage bipolar-junction-transistor (BJT) amplifier topologies, typically used as a voltage amplifier. It offers high current gain, medium input resistance and a high output resistance. The output of a common emitter amplifier is inverted; i.e. for a sine wave input signal, the output signal is 180 degrees out of phase with respect to the input.

In electronics engineering, frequency compensation is a technique used in amplifiers, and especially in amplifiers employing negative feedback. It usually has two primary goals: To avoid the unintentional creation of positive feedback, which will cause the amplifier to oscillate, and to control overshoot and ringing in the amplifier's step response. It is also used extensively to improve the bandwidth of single pole systems.

Linear electronic oscillator circuits, which generate a sinusoidal output signal, are composed of an amplifier and a frequency selective element, a filter. A linear oscillator circuit which uses an RC network, a combination of resistors and capacitors, for its frequency selective part is called an RC oscillator.

<span class="mw-page-title-main">Headphone amplifier</span>

A headphone amplifier is a low-powered audio amplifier designed particularly to drive headphones worn on or in the ears, instead of loudspeakers in speaker enclosures. Most commonly, headphone amplifiers are found embedded in electronic devices that have a headphone jack, such as integrated amplifiers, portable music players, and televisions. However, standalone units are used, especially in audiophile markets and in professional audio applications, such as music studios. Headphone amplifiers are available in consumer-grade models used by hi-fi enthusiasts and audiophiles and professional audio models, which are used in recording studios.

This article illustrates some typical operational amplifier applications. Operational amplifiers are optimised for use with negative feedback, and this article discusses only negative-feedback applications. When positive feedback is required, a comparator is usually more appropriate. See Comparator applications for further information.

Bootstrapping is a technique in the field of electronics where part of the output of a system is used at startup.

A total harmonic distortion analyzer calculates the total harmonic content of a sinewave with some distortion, expressed as total harmonic distortion (THD). A typical application is to determine the THD of an amplifier by using a very-low-distortion sinewave input and examining the output. The figure measured will include noise, and any contribution from imperfect filtering out of the fundamental frequency. Harmonic-by-harmonic measurement, without wideband noise, can be measured by a more complex wave analyser.

A fully differential amplifier (FDA) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and differential outputs. In its ordinary usage, the output of the FDA is controlled by two feedback paths which, because of the amplifier's high gain, almost completely determine the output voltage for any given input.

<span class="mw-page-title-main">Valve RF amplifier</span> Device for electrically amplifying the power of an electrical radio frequency signal

A valve RF amplifier or tube amplifier (U.S.) is a device for electrically amplifying the power of an electrical radio frequency signal.

Technical specifications and detailed information on the valve audio amplifier, including its development history.

<span class="mw-page-title-main">Tube sound</span> Characteristic quality of sounds from vacuum tube amplifiers

Tube sound is the characteristic sound associated with a vacuum tube amplifier, a vacuum tube-based audio amplifier. At first, the concept of tube sound did not exist, because practically all electronic amplification of audio signals was done with vacuum tubes and other comparable methods were not known or used. After introduction of solid state amplifiers, tube sound appeared as the logical complement of transistor sound, which had some negative connotations due to crossover distortion in early transistor amplifiers. However, solid state amplifiers have been developed to be flawless and the sound is later regarded neutral compared to tube amplifiers. Thus the tube sound now means 'euphonic distortion.' The audible significance of tube amplification on audio signals is a subject of continuing debate among audio enthusiasts.

<span class="mw-page-title-main">Transimpedance amplifier</span> Amplifier that converts current to voltage

In electronics, a transimpedance amplifier (TIA) is a current to voltage converter, almost exclusively implemented with one or more operational amplifiers. The TIA can be used to amplify the current output of Geiger–Müller tubes, photo multiplier tubes, accelerometers, photo detectors and other types of sensors to a usable voltage. Current to voltage converters are used with sensors that have a current response that is more linear than the voltage response. This is the case with photodiodes where it is not uncommon for the current response to have better than 1% nonlinearity over a wide range of light input. The transimpedance amplifier presents a low impedance to the photodiode and isolates it from the output voltage of the operational amplifier. In its simplest form a transimpedance amplifier has just a large valued feedback resistor, Rf. The gain of the amplifier is set by this resistor and because the amplifier is in an inverting configuration, has a value of -Rf. There are several different configurations of transimpedance amplifiers, each suited to a particular application. The one factor they all have in common is the requirement to convert the low-level current of a sensor to a voltage. The gain, bandwidth, as well as current and voltage offsets change with different types of sensors, requiring different configurations of transimpedance amplifiers.

<span class="mw-page-title-main">Current-feedback operational amplifier</span>

The current-feedback operational amplifier is a type of electronic amplifier whose inverting input is sensitive to current, rather than to voltage as in a conventional voltage-feedback operational amplifier (VFA). The CFA was invented by David Nelson at Comlinear Corporation, and first sold in 1982 as a hybrid amplifier, the CLC103. An early patent covering a CFA is U.S. patent 4,502,020, David Nelson and Kenneth Saller. The integrated circuit CFAs were introduced in 1987 by both Comlinear and Elantec. They are usually produced with the same pin arrangements as VFAs, allowing the two types to be interchanged without rewiring when the circuit design allows. In simple configurations, such as linear amplifiers, a CFA can be used in place of a VFA with no circuit modifications, but in other cases, such as integrators, a different circuit design is required. The classic four-resistor differential amplifier configuration also works with a CFA, but the common-mode rejection ratio is poorer than that from a VFA.

The Blackmer gain cell is an audio frequency voltage-controlled amplifier (VCA) circuit with an exponential control law. It was invented and patented by David E. Blackmer between 1970 and 1973. The four-transistor core of the original Blackmer cell contains two complementary bipolar current mirrors that perform log-antilog operations on input voltages in a push-pull, alternating fashion. Earlier log-antilog modulators using the fundamental exponential characteristic of a p–n junction were unipolar; Blackmer's application of push-pull signal processing allowed modulation of bipolar voltages and bidirectional currents.

<span class="mw-page-title-main">Diamond buffer</span>

The diamond buffer or diamond follower is a four-transistor, two-stage, push-pull, translinear emitter follower, or less commonly source follower, in which the input transistors are folded, or placed upside-down with respect to the output transistors. Like any unity buffer, the diamond buffer does not alter the phase and magnitude of input voltage signal; its primary purpose is to interface a high-impedance voltage source with a low-impedance, high-current load. Unlike the more common compound emitter follower, where each input transistor drives the output transistor of the same polarity, each input transistor of a diamond buffer drives the output transistor of the opposite polarity. When the transistors operate in close thermal contact, the input transistors stabilize the idle current of the output pair, eliminating the need for a bias spreader.

References

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.