Quasi-peak detector

Last updated

A quasi-peak detector is a type of electronic detector or rectifier. Quasi-peak detectors for specific purposes have usually been standardized with mathematically precisely defined dynamic characteristics of attack time, integration time, and decay time or fall-back time.

Quasi-peak detectors play an important role in electromagnetic compatibility (EMC) testing of electronic equipment, where allowed levels of electromagnetic interference (EMI), also called radio frequency interference (RFI), are given with reference to measurement by a specified quasi-peak detector. This was originally done because the quasi-peak detector was believed to better indicate the subjective annoyance level experienced by a listener hearing impulsive interference to an AM radio station. [1] Over time standards incorporating quasi-peak detectors as the measurement device were extended to frequencies up to 1 GHz, [2] although there may not be any justification beyond previous practice for using the quasi-peak detector to measure interference to signals other than AM radio. [1] The quasi-peak detector parameters to be used for EMC testing vary with frequency. [3] Both CISPR and the U.S. Federal Communications Commission (FCC) limit EMI at frequencies above 1  GHz with reference to an average-power detector, rather than quasi-peak detector. [4]

Conceptually, a quasi-peak detector for EMC testing works like a peak detector followed by a lossy integrator. A voltage impulse entering a narrow-band receiver produces a short-duration burst oscillating at the receiver centre frequency. The peak detector is a rectifier followed by a low-pass filter to extract a baseband signal consisting of the slowly (relative to the receiver centre frequency) time-varying amplitude of the impulsive oscillation. The following lossy integrator has a rapid rise time and longer fall time, so the measured output for a sequence of impulses is higher when the pulse repetition rate is higher. The quasi-peak detector is calibrated to produce the same output level as a peak-power detector when the input is a continuous wave tone. [5]

The CISPR quasi-peak detector is used in EMC testing and is defined in Publication 16 of the International Special Committee on Radio Interference (CISPR) of the International Electrotechnical Commission (IEC). The CISPR quasi-peak detector applied to most conducted emissions measurements (0.15–30 MHz) is a detector with an attack time of 1 ms, a decay time of 160 ms and an IF filter setting of 9 kHz. The quasi-peak detector applied to most radiated emissions measurements (30–1000 MHz) has an attack time of 1 ms, a decay time 550 ms and an IF filter bandwidth of 120 kHz.[ citation needed ]

In audio quality measurement, quasi-peak rectifiers are specified in several standards. For example ITU-R 468 noise weighting uses a special rectifier incorporating two cascaded charging time constants. The PPM or peak programme meter used to measure programme levels is actually a quasi-peak reading meter, again with precisely defined dynamics. Flutter measurement also involves a standardised quasi-peak reading meter. In every case the dynamics are chosen to reflect the sensitivity of human hearing to brief sounds, ignoring those so brief that we do not perceive them, and weighting those of intermediate duration according to audibility.

See also

Related Research Articles

<span class="mw-page-title-main">Weighting filter</span>

A weighting filter is used to emphasize or suppress some aspects of a phenomenon compared to others, for measurement or other purposes.

<span class="mw-page-title-main">Electromagnetic compatibility</span> Electrical engineering concept

Electromagnetic compatibility (EMC) is the ability of electrical equipment and systems to function acceptably in their electromagnetic environment, by limiting the unintentional generation, propagation and reception of electromagnetic energy which may cause unwanted effects such as electromagnetic interference (EMI) or even physical damage to operational equipment. The goal of EMC is the correct operation of different equipment in a common electromagnetic environment. It is also the name given to the associated branch of electrical engineering.

<span class="mw-page-title-main">Spread spectrum</span> Spreading the frequency domain of a signal

In telecommunication, especially radio communication, spread spectrum are techniques by which a signal generated with a particular bandwidth is deliberately spread in the frequency domain over a wider frequency band. Spread-spectrum techniques are used for the establishment of secure communications, increasing resistance to natural interference, noise, and jamming, to prevent detection, to limit power flux density, and to enable multiple-access communications.

<span class="mw-page-title-main">Spectrum analyzer</span> Electronic testing device

A spectrum analyzer measures the magnitude of an input signal versus frequency within the full frequency range of the instrument. The primary use is to measure the power of the spectrum of known and unknown signals. The input signal that most common spectrum analyzers measure is electrical; however, spectral compositions of other signals, such as acoustic pressure waves and optical light waves, can be considered through the use of an appropriate transducer. Spectrum analyzers for other types of signals also exist, such as optical spectrum analyzers which use direct optical techniques such as a monochromator to make measurements.

<span class="mw-page-title-main">Equal-loudness contour</span> Frequency characteristics of hearing and perceived volume

An equal-loudness contour is a measure of sound pressure level, over the frequency spectrum, for which a listener perceives a constant loudness when presented with pure steady tones. The unit of measurement for loudness levels is the phon and is arrived at by reference to equal-loudness contours. By definition, two sine waves of differing frequencies are said to have equal-loudness level measured in phons if they are perceived as equally loud by the average young person without significant hearing impairment.

<span class="mw-page-title-main">Electromagnetic interference</span> Disturbance in an electrical circuit due to external sources of radio waves

Electromagnetic interference (EMI), also called radio-frequency interference (RFI) when in the radio frequency spectrum, is a disturbance generated by an external source that affects an electrical circuit by electromagnetic induction, electrostatic coupling, or conduction. The disturbance may degrade the performance of the circuit or even stop it from functioning. In the case of a data path, these effects can range from an increase in error rate to a total loss of the data. Both human-made and natural sources generate changing electrical currents and voltages that can cause EMI: ignition systems, cellular network of mobile phones, lightning, solar flares, and auroras. EMI frequently affects AM radios. It can also affect mobile phones, FM radios, and televisions, as well as observations for radio astronomy and atmospheric science.

A weighting curve is a graph of a set of factors, that are used to 'weight' measured values of a variable according to their importance in relation to some outcome. An important example is frequency weighting in sound level measurement where a specific set of weighting curves known as A-, B-, C-, and D-weighting as defined in IEC 61672 are used. Unweighted measurements of sound pressure do not correspond to perceived loudness because the human ear is less sensitive at low and high frequencies, with the effect more pronounced at lower sound levels. The four curves are applied to the measured sound level, for example by the use of a weighting filter in a sound level meter, to arrive at readings of loudness in phons or in decibels (dB) above the threshold of hearing.

The Comité International Spécial des Perturbations Radioélectriques was founded in 1934 to set standards for controlling electromagnetic interference in electrical and electronic devices and is a part of the International Electrotechnical Commission (IEC).

<span class="mw-page-title-main">ITU-R 468 noise weighting</span> Noise measurement standard

ITU-R 468 is a standard relating to noise measurement, widely used when measuring noise in audio systems. The standard, now referred to as ITU-R BS.468-4, defines a weighting filter curve, together with a quasi-peak rectifier having special characteristics as defined by specified tone-burst tests. It is currently maintained by the International Telecommunication Union who took it over from the CCIR.

<span class="mw-page-title-main">Sound level meter</span> Device for acoustic measurements

A sound level meter is used for acoustic measurements. It is commonly a hand-held instrument with a microphone. The best type of microphone for sound level meters is the condenser microphone, which combines precision with stability and reliability. The diaphragm of the microphone responds to changes in air pressure caused by sound waves. That is why the instrument is sometimes referred to as a sound pressure level meter (SPL). This movement of the diaphragm, i.e. the sound pressure, is converted into an electrical signal. While describing sound in terms of sound pressure, a logarithmic conversion is usually applied and the sound pressure level is stated instead, in decibels (dB), with 0 dB SPL equal to 20 micropascals.

Audio noise measurement is a process carried out to assess the quality of audio equipment, such as the kind used in recording studios, broadcast engineering, and in-home high fidelity.

In telecommunication, a measuring receiver or measurement receiver is a calibrated laboratory-grade radio receiver designed to measure the characteristics of radio signals. The parameters of such receivers can be adjusted over a much more comprehensive range of values than other radio receivers. Their circuitry is optimized for stability and enables calibration and reproducible results. Some measurement receivers also have exceptionally robust input circuits that can survive brief impulses of more than 1000 V, as they can occur during measurements of radio signals on power lines and other conductors.

In the field of EMC, active EMI reduction refers to techniques aimed to reduce or to filter electromagnetic noise (EMI) making use of active electronic components. Active EMI reduction contrasts with passive filtering techniques, such as RC filters, LC filters RLC filters, which includes only passive electrical components. Hybrid solutions including both active and passive elements exist. Standards concerning conducted and radiated emissions published by IEC and FCC set the maximum noise level allowed for different classes of electrical devices. The frequency range of interest spans from 150 kHz to 30 MHz for conducted emissions and from 30 MHz to 40 GHz for radiated emissions. Meeting these requirements and guaranteeing the functionality of an electrical apparatus subject to electromagnetic interference are the main reason to include an EMI filter. In an electrical system, power converters, i.e. DC/DC converters, inverters and rectifiers, are the major sources of conducted EMI, due to their high-frequency switching ratio which gives rise to unwanted fast current and voltage transients. Since power electronics is nowadays spread in many fields, from power industrial application to automotive industry, EMI filtering has become necessary. In other fields, such as the telecommunication industry where the major focus is on radiated emissions, other techniques have been developed for EMI reduction, such as spread spectrum clocking which makes use of digital electronics, or electromagnetic shielding.

Electromagnetic near-field scanner (NFS) is a measurement system to determine a spatial distribution of an electrical quantity provided by a single or multiple field probes acquired in the near-field region of a device under test possibly accompanied by the associated numerical post-processing methods enabling a conversion of the measured quantity into electromagnetic field.

IEC 61000-3-2Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions is an international standard that limits mains voltage distortion by prescribing the maximum value for harmonic currents from the second harmonic up to and including the 40th harmonic current. IEC 61000-3-2 applies to equipment with a rated current up to 16 A – for equipment above 16 A see IEC 61000-3-12.

<span class="mw-page-title-main">Conducted emissions</span>

Conducted emissions are the effects in power quality that occur via electrical and magnetic coupling, electronic switch of semiconductor devices, which form a part of electromagnetic compatibility issues in electrical engineering. These affect the ability of all interconnected system devices in the electromagnetic environment, by restricting or limiting their intentional generation, propagation and reception of electromagnetic energy.

Switching Control Techniques address electromagnetic interference (EMI) mitigation on power electronics (PE). The design of power electronics involves overcoming three key challenges:

  1. power losses
  2. EMI
  3. harmonics
<span class="mw-page-title-main">Low-frequency electromagnetic compatibility</span>

Low-frequency electromagnetic compatibility is a specific field in the domain of electromagnetic compatibility (EMC) and power quality (PQ), which deals with electromagnetic interference phenomena in the frequency range between 2 kHz and 150 kHz. It is a special frequency range because it does not fit in the PQ problems, with range of up to 2 kHz, where relative levels of voltage and current can have massive impact on efficiency and integrity of electric systems, and neither in the conducted EMC range, which starts at 150 kHz and influences mainly informational systems, and already too far from radiated EMC range, which starts at 30 MHz and goes up to 1 GHz.

References

  1. 1 2 Edwin L. Bronaugh (2001). "The Quasi-Peak Detector" . Retrieved 2018-06-11.
  2. ↑ John R. Barnes (2003-07-23). "EMC/EMI/ESD STANDARDS FOR INFORMATION TECHNOLOGY EQUIPMENT (ITE)" . Retrieved 2007-09-07.
  3. ↑ "American National Standard for Electromagnetic Noise and Field Strength Instrumentation, 10 Hz to 40 GHz-Specifications". ANSI C63.2-1996. IEEE. 1996-01-12. Archived from the original on May 20, 2000. Retrieved 2007-09-07.
  4. ↑ "Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement". IEC CISPR22:2008. IEC. 2008-09-24. Retrieved 2015-01-30.
  5. ↑ Ott, Henry (1987). Electromagnetic Compatibility Engineering. p. 709.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.