RRG Urubu Obs

Last updated
Urubu Obs
RoleMeteorological research glider
National origin Germany
Manufacturer Rhön-Rossitten Gesellschaft (RRG)
Designer Alexander Lippisch
First flight1932
Number built1

The RRG Urubu Obs (the Urubu is an Argentinian Vulture), often known just as the RRG Obs, was a one-off, large, two or three seat glider designed for meteorological observations by Alexander Lippisch in Germany and first flown in 1932.

Contents

Design and development

In 1931 Professor Walter Georgii, an academic meteorologist and head of the Rhön-Rossitten Gesellschaft (RRG) asked Alexander Lippisch to design a glider for meteorological research. In addition to the pilot, space was required for two observers or, more usually, one with a variety of meteorological instruments, so the Urubu Obs had to be a large glider. [1]

Its wooden high gull wing had a rectangular centre section, occupying about 20% of the overall 26 m (85 ft 4 in) span and mounted with marked dihedral. On each side a pair of rearwards leaning N-form lift struts braced the end of this section to the lower fuselage longeron. The outer panels had no dihedral and were strongly straight tapered, with a taper ratio of 1:4.7, though the trailing edges were unswept. They were also strongly tapered in thickness. Its large area wing and consequent low wing loading meant the Obs flew slowly. The thin, narrow chord wing tips carried endplate fins; like those on some of Lippisch's Storch tailless gliders, these carried rudders that were coupled to the conventional rear rudder, assisting it and allowing the Obs to have a short fuselage. The trailing edge of each outer panel carried three equal span ailerons. The outer one, together with that on the other wing, acted as differential ailerons but the inner pair also served as camber changing flaps. There is some doubt whether or not the wing was fitted with inboard upper surface airbrakes; these may have been added as a result of test flying. [1] [2]

The Obs had a rectangular section, steel tube framed, fabric covered fuselage. Its cockpit, under a multi-piece canopy was ahead of the forward wing root fairing; the wing was carefully merged into the fuselage, with root extensions at both leading and trailing edges. The meteorologists' cabin was under the wing where the fuselage width was 700 mm (27.6 in), with both side and roof windows. Both the pilot and observers entered via a detachable hood; cabin and cockpit were connected via a door. Below them were a side-by-side pair of fixed, semi-recessed landing wheels. The fuselage tapered to the tail, where a short, narrow fin carried a broad chord, triangular, blunt apexed balanced rudder that extended to the keel. Its mass balanced, all-moving tailplane was mounted on inverted V-form struts from its mid-span, forward underside to the lower fuselage, placing it above the fuselage with its leading edge just ahead of the fin. [1] [2]

After flying at the Wasserkuppe in 1932 with the aid of powerful tug aircraft, it was moved to Darmstadt to commence its intended meteorological observations. It was on view at a meteorological conference in Munich in 1934. [1] [2]

Specifications

Data from Sailplanes 1920-1945 [1]

General characteristics

Performance


Related Research Articles

DFS Reiher German single-seat glider, 1937

The DFS Reiher was a single seat competition glider designed in Germany by Hans Jacobs and first flown in 1937. The type won the last two German Rhön gliding championships before the start of World War II. Six were factory produced.

Schleicher Rhönbussard German training glider, 1933

The Schleicher Rhönbussard, otherwise known as the DFS Rhönbussard was intended as an intermediate glider trainer which could also fly competitively. It was designed by Hans Jacobs in Germany in the early 1930s. More than 200 were built.

Schleicher Rhönadler German single-seat glider, 1932

The Schleicher Rhönadler, DFS Rhönadler or Jacobs Rhönadler is a high performance, single seat competition sailplane built in Germany in the 1930s. More than 65 were built.

The Bonomi BS.2 Balestruccio was an Italian sailplane designed to set records. In 1932 it set a new national endurance record with a flight of over 25 minutes.

Lippisch Wien German single-seat glider, 1929

The Lippisch Wien was a high-performance glider designed by Alexander Lippisch in Germany in 1929. Owned and flown by Robert Kronfeld, it was one of the first sailplanes intended to exploit thermals. It set world records both for distance and altitude and demonstrated the practicality of long-distance cross-country flights.

The Sala N1 or N1 Sala was a single-seat,18 m span competition glider built in Italy in 1937. Only one was constructed.

The Teichfuss Nibio was an Italian single seat glider, designed by Luigi Teichfuss and flown in two versions around 1930.

The Teichfuss Falco was an Italian single-seat, intermediate-performance glider, designed by Luigi Teichfuss and flown in 1931.

The Teichfuss Supergrifo or Super Grifo was an Italian competition glider designed by Luigi Teichfuss and flown in 1935. Only one was built.

The Teichfuss Cicogna was an Italian tailless single-seat motor glider designed by Luigi Teichfuss and flown in 1936.

The Teichfuss Astore was an Italian Intermediate single-seat trainer glider designed by Luigi Teichfuss and flown in 1936. Two were built.

RRG Fafnir German single-seat glider, 1930

The RRG Fafnir, named after the legendary dragon, was a single seat German high performance glider designed by Alexander Lippisch. It won the Rhön competition in 1931 and made several outstanding flights as well as setting a fashion for gull wings.

RRG Fafnir 2 German single-seat glider, 1934

The RRG Fafnir 2 São Paulo, named after the legendary dragon and the Brazilian city which partially financed it, was a single seat German high performance glider designed by Alexander Lippisch. It set a new world distance record in 1934 and won the 1937 International Gliding Championships.

The RRG Professor was a very early soaring glider and the first to use a variometer for finding thermals. It was designed by Alexander Lippisch in Germany, first flying in 1928. The Professor was widely built by both flying clubs and factories.

RRG Falke German single-seat glider, 1930

The RRG Falke of 1930 was a secondary training glider designed by Alexander Lippisch in Germany and intended to provide better performance than his earlier RRG Prüfling whilst being easier to fly because of its inherent stability. It was sold as plans for both club and commercial production and was built in Germany and abroad.

The Schneider Grunau 7 Moazagotl was a high-performance sailplane designed in Germany in 1933 specifically for fast, long distance flying using strong thermals. In 1937 it came second in the first World Gliding Championships, having previously made a flight of 300 km (186 mi).

RRG Storch V Aircraft

The RRG Storch V was the only member of Alexander Lippisch's Storch series of tailless aircraft to be powered. It flew successfully in the year 1929.

Avia 41-P Single-seat French glider, 1932

The Avia 41-P was a high performance French glider. Eric Nessler set many new national gliding records in one between 1934 and 1938.

Rubik R-03 Szittya I

The Rubik R-03 Szittya I was a Hungarian single-seat sailplane flown in the late 1930s. The design was developed through three improving variants. though only one of each was built.

The RRG Delta I was a German experimental tailless aircraft flown in the early 1930s first as a glider and then powered. It was one of the first delta wing aircraft.

References

  1. 1 2 3 4 5 Simons, Martin (2006). Sailplanes 1920-1945 (2nd revised ed.). Königswinter: EQIP Werbung & Verlag GmbH. pp. 69–70. ISBN   3-9806773-4-6.
  2. 1 2 3 "A Two-Seater for Research". The Sailplane. 4 (4): 41–2. 3 March 1933.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.