A weaving shed is a distinctive type of mill developed in the early 1800s in Lancashire, Derbyshire and Yorkshire to accommodate the new power looms weaving cotton, silk, woollen and worsted. A weaving shed can be a stand-alone mill, or a component of a combined mill. Power looms cause severe vibrations requiring them to be located on a solid ground floor. In the case of cotton, the weaving shed needs to remain moist. Maximum daylight is achieved, by the sawtooth "north-facing roof lights". [1]
The early textile trade relied on domestic outworking. Handloom weavers would take the yarn to their cottage loom shops, and return the completed fabric to the mill. Reliable power looms that could be worked from an overhead line shaft were not available before Kenworthy and Bulloughs weft stop motion, the roller temple and the loose reed which appeared in the 1840s. [2] The first weaving floors were on the ground floor of the existing narrow mills, where the workpiece was lit by tall exterior windows. The weaving shed appeared around this time. They initially adjoined existing mills, and then were built as standalone mills by speculating investors or by industrial cooperatives of former handloom weavers. Either group would run the looms themselves or operate the shed as a room and power mill. Here as the name suggests, space was rented to other companies who could specialise in weaving without the skills needed to finance, build and maintain a building. [3] Weaving sheds were cheap to build and fireproof having no wooden beams. They were also safer, because their north-facing roof windows meant they were not as dependent on gas-lighting as were spinning mills.
The purpose of a weaving shed was to provide spaces for rows and rows of identical looms. A standard shed would house 1200 looms, and it was common to think in multiples of 400 looms. These looms would be tentered by weavers who worked from four to eight looms each [4] and were paid on piece-rate. The looms would be maintained by a skilled tackler who would be on hand to gait the looms and effect instant repairs or adjustments. There would be four tacklers for 400 looms. [4] The looms were powered by leather belts from overhead cross-shafts, on bevel gears from the line shaft that ran the length of the shed. [5]
Attached to the weaving shed in a typical mill would be a boiler house where the steam was raised, [6] an engine room housing a stationary steam engine [7] and a two or three-storey building where the preparatory processes were done below and above would be the warehouse. This also housed the offices. Weaving was not possible without a continuous supply of weft on pirns, and beams carrying the warp. Starting with the warp, it had to be warped from creels of thread, in a multistage process onto the weavers' beam. This could be done in the mill or the warp could be bought in and delivered on the tapers beam. The beam of thread had to be sized in a tape sizing machine by sizers. [8]
Each thread had to pass through the correct eye in the heddle, and through the reed. This was done on a drawing-in frame by loomers. [9] The beam, heddles and reed would be carried through into the weaving-shed and gaited to the loom by the tackler.s [10] The pirns used for the weft in the shuttles were wound by a pirner, on a pirning machine [11] in the shed or be bought shuttle ready from the spinners. [4] The completed pieces would be cut off the loom, (it was on a takeup beam), and this left the shed to go back to the warehouse where it would be examined for faults by the cloth looker, and if it was of satisfactory quality, folded and forwarded to the client. [4] The payroll and paper work was done by office staff. [12]
The early weaving sheds were simple working industrial buildings and the external materials generally used in their construction are robust and there was little in the way of ornamentation. External walls were generally in coursed rubble, stone or brick. The few openings or windows were in simple detailed timber joinery. Internal materials comprised stone flag floors, exposed cast iron structure, timber joinery and boarded partitions and lime plaster on lath soffits to the south facing roof slopes. The sheds were often built into the hillside so the wall would benefit from contact with damp earth that would maintain the moisture levels in the shed required by cotton weaving. [13]
The shed would be modular using a 3m by 6m bay, the beams of the roof being supported by cast iron columns. The ground to beam clearance was 3.5m and the ground to ridge height was 4.6m. Later sheds used a longitudinal beam under the gutter beam eliminating the need for a row of columns, [14] creating a 6m by 6m lattice. The modular nature enable sheds to infill on irregularly shaped sites. [15]
The north light roofs to the majority of weaving sheds were constructed with simple 30-degree pitched roofs, comprising a simple structure of common rafters with slate roof coverings facing south and glazed lights to the north. [16] The cast iron beams that support these rows of north lights are ingeniously designed as inverted channel sections such that they both carry the load of the roofs and act as rainwater gutters. The rainwater would exit to identical drainpipes on the east and west exterior walls.
The gutter beams were laid flat with joints aligned over column heads. The end of each gutter section has an external flange enabling sections to be bolted together over a bracket to the head of the column. The brackets were designed to collect any resulting leak at the joint and channelled it down the inside of the hollow columns. [13] Cast iron tie rods running from the columnheads, at right angles to the gutterbeams, gave lateral rigidity. The columns were the mounting points for the lineshaft bearings.
Though the North Light Roof Shed predominated in Lancashire and Yorkshire, there were always variations caused by local needs. In Brazil in the southern hemisphere the south lit roof was more appropriate. Domed vault were used in Leeds, United Kingdom and Issenheim, France but were expensive to build and were dark. Flat roofs on vaults with monitor lights were chosen in Italy, parts of the United States and India because they helped to reduce the heat. Brick vaulting was used in Catalunya, and in settlements that were short of land, two-storey building were erected with the weaving below and the spinning above. Similar two-storey mills were built in 1865 in Angus, Scotland. At Salts Mill in Bradford and in Dundee the power was from below rather than above giving greater headroom while the lace mills of Nottingham and the woollen tweed mills in Roxburghshire had higher roofs to allow for overhead supervision gantries. The Tonnendach mills of central and northern Europe, used a curved broad span with raised transverse rooflights, a system patented by Sequin-Brunner of Switzerland in 1885. Wrought-iron lattice trusses were favoured in France after 1870, while in Ireland the curved light timber Belfast truss was used by Barbour Threads in Hilden, Ulster. [17] [ full citation needed ]
By the 1980s the final weaving companies were woven out (closed), [18] and in a few cases the mills were mothballed. [19] Most however had already been converted for alternative use- and in 2010 a report was written detailing possible ways that the weaving sheds could be renovated and put to alternative uses.
The challenge lies in having 1000 m2 of top lit shed with no exterior windows, having structural columns every 3.6m. There are successful schemes which convert the shed into covered parking, and divided retail space, offices and business start up units. When part of the centre is opened up to form an inner court, the bays round the edge have been converted into a primary school, residential units and student accommodation.
A loom is a device used to weave cloth and tapestry. The basic purpose of any loom is to hold the warp threads under tension to facilitate the interweaving of the weft threads. The precise shape of the loom and its mechanics may vary, but the basic function is the same.
Weaving is a method of textile production in which two distinct sets of yarns or threads are interlaced at right angles to form a fabric or cloth. Other methods are knitting, crocheting, felting, and braiding or plaiting. The longitudinal threads are called the warp and the lateral threads are the weft, woof, or filling. The method in which these threads are interwoven affects the characteristics of the cloth. Cloth is usually woven on a loom, a device that holds the warp threads in place while filling threads are woven through them. A fabric band that meets this definition of cloth can also be made using other methods, including tablet weaving, back strap loom, or other techniques that can be done without looms.
The spinning jenny is a multi-spindle spinning frame, and was one of the key developments in the industrialisation of textile manufacturing during the early Industrial Revolution. It was invented in 1764–1765 by James Hargreaves in Stan hill, Oswaldtwistle, Lancashire in England.
A power loom is a mechanized loom, and was one of the key developments in the industrialization of weaving during the early Industrial Revolution. The first power loom was designed and patented in 1785 by Edmund Cartwright. It was refined over the next 47 years until a design by the Howard and Bullough company made the operation completely automatic. This device was designed in 1834 by James Bullough and William Kenworthy, and was named the Lancashire loom.
In the manufacture of cloth, warp and weft are the two basic components in weaving to transform thread and yarn into textile fabrics. The vertical warp yarns are held stationary in tension on a loom (frame) while the horizontal weft is drawn through the warp thread. In the terminology of weaving, each warp thread is called a warp end ; a pick is a single weft thread that crosses the warp thread.
A cotton mill is a building that houses spinning or weaving machinery for the production of yarn or cloth from cotton, an important product during the Industrial Revolution in the development of the factory system.
The flying shuttle is a type of weaving shuttle. It was a pivotal advancement in the mechanisation of weaving during the initial stages of the Industrial Revolution, and facilitated the weaving of considerably broader fabrics, enabling the production of wider textiles. Moreover, its mechanical implementation paved the way for the introduction of automatic machine looms.
Textile manufacture during the British Industrial Revolution was centred in south Lancashire and the towns on both sides of the Pennines in the United Kingdom. The main drivers of the Industrial Revolution were textile manufacturing, iron founding, steam power, oil drilling, the discovery of electricity and its many industrial applications, the telegraph and many others. Railroads, steamboats, the telegraph and other innovations massively increased worker productivity and raised standards of living by greatly reducing time spent during travel, transportation and communications.
A shuttle is a tool designed to neatly and compactly store a holder that carries the thread of the weft yarn while weaving with a loom. Shuttles are thrown or passed back and forth through the shed, between the yarn threads of the warp in order to weave in the weft.
Textile manufacturing or textile engineering is a major industry. It is largely based on the conversion of fibre into yarn, then yarn into fabric. These are then dyed or printed, fabricated into cloth which is then converted into useful goods such as clothing, household items, upholstery and various industrial products.
A weavers' cottage was a type of house used by weavers for cloth production in the putting-out system sometimes known as the domestic system.
The Lancashire Loom was a semi-automatic power loom invented by James Bullough and William Kenworthy in 1842. Although it is self-acting, it has to be stopped to recharge empty shuttles. It was the mainstay of the Lancashire cotton industry for a century.
Queen Street Mill is a former weaving mill in Harle Syke, a suburb to the north-east of Burnley, Lancashire, that is a Grade I listed building. It now operates as a museum and cafe. Currently open for public tours between April and November. Over winter the café is opened on Wednesdays. It is also viewable with private bookings.
A beamer was an occupation in the cotton industry. The taper's beam is a long cylinder with flanges where 400 plus ends (threads) are wound side-by-side. Creels of bobbins with the correct thread, mounted on a beaming frame wind their contents onto the beam. The machine is watched over by a "beamer".
Bancroft Shed was a weaving shed in Barnoldswick, Lancashire, England, situated on the road to Skipton. Construction was started in 1914 and the shed was commissioned in 1920 for James Nutter & Sons Limited. The mill closed on 22 December 1978 and was demolished. The engine house, chimneys and boilers have been preserved and maintained as a working steam museum. The mill was the last steam-driven weaving shed to be constructed and the last to close.
The more looms system was a productivity strategy introduced in the Lancashire cotton industry, whereby each weaver would manage a greater number of looms. It was an alternative to investing in the more productive Northrop automatic looms in the 1930s. It caused resentment, resulted in industrial action, and failed to achieve any significant cost savings.
"Kissing the shuttle" is the term for a process by which weavers used their mouths to pull thread through the eye of a shuttle when the pirn was replaced. The same shuttles were used by many weavers, and the practice was unpopular. It was outlawed in the U.S. state of Massachusetts in 1911 but continued even after it had been outlawed in Lancashire, England in 1952. The Lancashire cotton industry was loath to invest in hand-threaded shuttles, or in the more productive Northrop automatic looms with self-threading shuttles, which were introduced in 1902.
Piece-rate lists were the ways of assessing a cotton operatives pay in Lancashire in the nineteenth and early twentieth centuries. They started as informal agreements made by one cotton master and their operatives then each cotton town developed their own list. Spinners merged all of these into two main lists which were used by all, while weavers used one 'unified' list.
Harle Syke mill is a weaving shed in Briercliffe on the outskirts of Burnley, Lancashire, England. It was built on a green field site in 1856, together with terraced houses for the workers. These formed the nucleus of the community of Harle Syke. The village expanded and six other mills were built, including Queen Street Mill.
William Horrocks, a cotton manufacturer of Stockport built an early power loom in 1803, based on the principles of Cartwright but including some significant improvements to cloth take up and in 1813 battening.
{{cite book}}: CS1 maint: location missing publisher (link) 
Media related to Weaving sheds at Wikimedia Commons