IBM 2401 System/360 tape drives that introduced the 9-track formatFull-size reel of 9-track tape
9-track tape is a format for magnetic-tape data storage, introduced with the IBM System/360 in 1964. The 1⁄2 inch (12.7mm) wide magnetic tape media and reels have the same size as the earlier IBM 7-track format it replaced, but the new format has eight data tracks and one parity track for a total of nine parallel tracks. Data is stored as 8-bit characters, spanning the full width of the tape (including the parity bit). Various recording methods have been employed during its lifetime as tape speed and data density increased, including PE (phase encoding), GCR (group-coded recording), and NRZI (non-return-to-zero, inverted, sometimes pronounced "nur-zee"). Tapes come in various sizes up to 3,600 feet (1,100m) in length.
The standard size of a byte was effectively set at eight bits with the S/360 and nine-track tape.
For over 30 years the format dominated offline storage and data transfer, but by the end of the 20th century it was obsolete, and the last manufacturer of tapes ceased production in early 2002,[1] with drive production ending the next year.[2]
Typical operation
9-track tape drive used with DEC minicomputersInside a 9-track tape drive. The vacuum columns are the two gray rectangles on the left.
A typical 9-track unit consists of a tape transport—essentially all the mechanics that moves tape from reel to reel past the read/write and erase heads—and supporting control and data read/write electronics. The transport typically consists of a supply motor, a take-up motor, hubs for locking the tape reels in place, a capstan motor (though not necessarily a pinch roller, see below), tape head assembly, miscellaneous rollers which keep the tape in a precise path during operation, and vacuum columns which prevent tape 'snatch'. Data can become corrupted by stretched tape or variations in tape speed, so the transport has to guide the tape through without damaging its edges, move it with minimal wow and flutter, and give it a tension that is low but sufficient to keep the tape in constant contact with the read/write head.
To load a tape, an operator removes the protective ring (frequently called a "tape seal belt" because its purpose is to prevent humidity and dust on the media) from the outside of the tape reel and installs the tape on the supply hub, then threads the tape leader through the various roller assemblies and onto the take-up reel, installing three or four winds of tape to provide enough friction for the take-up motor to be able to pull the tape. The operator then initiates an automatic sequence, often by a single press of a button, that closes the protective window, starts the vacuum system, then moves the tape forward until the beginning-of-tape (BOT) foil strip is detected by an optical sensor in the tape path. The control electronics then indicate to the controlling computer that the unit is ready for operation.
Like its audio counterpart, moving tape past the read/write heads on a nine-track digital tape drive requires precise control, accomplished by a capstan motor. The capstan motor is designed for very smooth operation. Feedback to the control electronics is accomplished by a tachometer, usually an optical "tone wheel", to control tape velocity. Starting and stopping the capstan is controlled by ramp generators to ensure a properly sized inter-record gap, the gap between blocks of information.
The vacuum system provides a physical buffer between the precision movements of the capstan and the large movements of the reels by storing a short length of tape in the vacuum column under relatively low tension. The vacuum columns are chambers open at one end, the openings being in line with the tape path before and after the capstan and roller assemblies. The amount of tape in the column is controlled by four optical or vacuum sensors on the sides of the columns. The control electronics keep the curve of the tape loop between the two inner sensors, cueing the supply reel to feed more or stop, and the take-up reel to take more or stop, as necessary. The outer two sensors, at the very top and bottom of the columns, serve to sense malfunctions in the feed mechanism during operation, prompting the control electronics to shut off all operation of the tape transport and vacuum system to prevent damaging the tape. Because of the tension provided by the vacuum columns and the design of the tape path, tape is usually kept in sufficient contact with the relatively high-friction coating on the capstan that a pinch roller is not used.
Tape motion on many systems is bidirectional, i.e. tape can be read either forward or backward at the request of the controlling computer. Because the supply vacuum column keeps a small, constant tension in the reverse direction, the capstan can feed backwards without the tape bunching up or jumping out of its path. Unlike most audio tape systems, the capstan and head assemblies are always in contact with the tape, even during fast forward and reverse operations, only moving the head assembly away from the tape path during high-speed rewind. On some units, manufacturers provided a "fast search" capability which can move the tape quickly a certain number of blocks, then bring the tape to a halt and go back to read the requested data at normal speed.
Tapes include an end-of-tape (EOT) foil strip. When EOT is encountered while writing, the computer program is notified of the condition. This gives the program a chance to write end-of-tape information on the tape while there is still enough tape to do so.
The sensing of BOT and EOT is achieved by shining a small lamp at the tape's surface at an oblique angle. When the foil strip (glued to the tape) moves past the lamp a photo-receptor sees the reflected flash of light and triggers the system to halt tape motion. This is the main reason that photographic flash cameras are not allowed in data centers with 9-track tape drives since they can trick the tape drives into falsely sensing BOT and EOT.[3]
The above describes a typical transport system; however, manufacturers engineered many alternative designs. For example, some designs use a horizontal transport deck where the operator simply sets the tape reel in the supply reel bay, closes the door and presses the load button, then a vacuum system draws the tape along the path and onto a take-up hub within the mechanism. Some designs eliminate the vacuum columns in favor of a microprocessor-controlled direct drive design.
Technical details
9-track 800 NRZI and 1600 PE (phase encoding) tapes use a 0.6 inches (15mm) inter-record gap (IRG) between data records to allow the tape to stop and start between records. 6250 GCR tapes use a tighter 0.3 inches (7.6mm) IRG.
9-track tapes have reflective stickers placed on the non-data side 10 feet (3.0m) from the beginning of the tape and 14 feet (4.3m) from the end of the tape to facilitate signaling the hardware to prevent the tape from unwinding from the hubs. These reflective stickers establish the beginning-of-tape (BOT) and end-of-tape (EOT) marks. 10 feet (3.0m) of leader and trailer tape is sufficiently long to allow the tape to go down and up the air columns and wrap around the hub a few times. The extra 4 feet (1.2m) in the trailer is to allow the operating system space to write a few blocks of data after the EOT mark to finalize the tape data segment in a multi-volume dataset. Operators commonly clip off a few inches of leader tape when it becomes frayed. If the leading reflective strip becomes detached from the tape it becomes difficult to read the data, since the BOT point of the dataset is no longer easily located and BOT orientation is nearly impossible. When this happens a new BOT strip is added to the tape and its former data is considered lost.
Nine-track tapes have densities of 800, 1600, and 6250 8-bit bytes per inch, giving approximately 22.5MB, 45MB and 175MB respectively on a tape with the usual length of 2,400 feet (730m).
IBM generations
IBM Model
2400 Series
3400 Series
Model numbers
2401, 2415, 2420
3410, 3420, 3422, 3440
Density (bits/in/track)
800, 1600
800, 1600, 6250
Tape speed (in/s)
18.75–200
75–200
Transfer rate (byte/s)
15,000–320,000
1,250,000
Interblock gap (in)
0.6
0.3-0.6
Rewind speed (full reel)
1–4 minutes
51–180 seconds
Start time (ms)
Stop time (ms)
Length of reel (ft)
2400 max
2400 max
Base composition
Plastic
Plastic
2400 Series
The 2400 Series Magnetic Tape Units were introduced with the System/360 and were the first to use 9-track tape. The dimensions of the tape and reels are identical to those used with 7-track units, such as the IBM 729. But older 7-track tapes can be read and written only on special 2400 drives equipped with 7-track read and write heads and the 7-track compatibility option.
3400 Series
The 3400 Series Magnetic Tape Units were introduced with the IBM System/370. The primary advantages of the 3400 system are the higher data density (6250 BPI) and support of the "autoloader" cartridge, first seen in the IBM 2420 model 7. Prior to the autoloader cartridge, tapes were sealed in a plastic "tape seal belt" that surrounded the reel and provided contamination protection and rack-hanging capability. The 3420's autoloader cartridge enables the tape operator to mount the reel directly on the hub without having to remove the seal belt. This provides a significant time saving and reduces operator errors, since the operator does not have to remove/replace the belt or thread the tape onto the take-up reel.
Other IBM units
While the earlier tape drives have vacuum columns, some IBM tape drives such as the 8809 drive (1980's) have a flat mount situation and no vacuum columns exist. Tapes are manually mounted and threaded. The drive supports both 800 and 1600 bpi. This drive is used on the IBM System/36. On the IBM AS/400 and iSeries there is the 9348-012 and it is a table top drive, flat mounting, but it autoloads the tape reel and auto threads it. The 9348 supports 1600 and 6250 bpi density tapes.
Other information
The maximum data capacity of a 2400ft reel, with 32,767 byte blocks and recorded at 6250 BPI is 170megabytes. Typically, much smaller block sizes, such as 4K (4,096 bytes) are used, in which case the storage capacity of the tape is reduced to 113megabytes.
Depending on the operating system, tapes are formatted as either EBCDIC (if IBM equipment is used) or ASCII, and are either "labeled" (if the data is preceded by a tape header, typically containing a tape name and date), "unlabeled" (if the tape contains no header) or have a "non-standard label" (the tape has a header, but it does not conform to the format expected by the equipment used to read the tape).
Data is often written to the tape in blocks, instead of one record at a time. Between blocks, there is an interblock gap, which varies depending on the density, but is typically 5/8 to 3/4 of an inch long. To maximize the amount of data that is stored on a tape, the number of gaps has to be minimized. Additionally, data stored in blocks can be read and written more quickly than data stored one record at a time. The disadvantage is that data corruption within a block can cause multiple records to be lost.
The write protection ring prevents the tape from being written when removed
A typical library of half-inch magnetic tape
3M 777 High Grade 6250 CPI - Security Computer Tape
Standards
ANSIINCITS 40-1993 (R2003) Unrecorded Magnetic Tape for Information Interchange (9-Track, 800 cpi [characters per inch], NRZI; 1600 cpi, PE; and 6250 cpi, GCR)
ISO/IEC 1863:1990 9-track, 12.7mm (1⁄2 in)-wide magnetic tape for information interchange using NRZ1 at 32 ftpmm (flux transitions per millimeter, 800 flux transitions per inch or ftpi) or 32 cpmm (characters per millimeter, 800 characters per inch or cpi)
ISO/IEC 3788:1990 9-track, 12.7mm (1⁄2 in) wide magnetic tape for information interchange using phase encoding at 126 ftpmm (3,200 ftpi), 63 cpmm (1,600 cpi)
ANSI INCITS 54-1986 (R2002) Recorded Magnetic Tape for Information Interchange (6250 cpi, Group Coded Recording)
ANSI INCITS 27-1987 (R2003) Magnetic Tape Labels and File Structure for Information Interchange
3M (later spun off into Imation) — The first manufacturer of 9-track tape.
Graham Magnetics — The last manufacturer to produce new 9-track tape (2001).
Related Research Articles
Disk storage is a data storage mechanism based on a rotating disk. The recording employs various electronic, magnetic, optical, or mechanical changes to the disk's surface layer. A disk drive is a device implementing such a storage mechanism. Notable types are hard disk drives (HDD), containing one or more non-removable rigid platters; the floppy disk drive (FDD) and its removable floppy disk; and various optical disc drives (ODD) and associated optical disc media.
A tape drive is a data storage device that reads and writes data on a magnetic tape. Magnetic-tape data storage is typically used for offline, archival data storage. Tape media generally has a favorable unit cost and long archival stability.
In computer science, group coded recording or group code recording (GCR) refers to several distinct but related encoding methods for representing data on magnetic media. The first, used in 6250 bpi magnetic tape since 1973, is an error-correcting code combined with a run-length limited (RLL) encoding scheme, belonging into the group of modulation codes. The others are similar encoding methods used in mainframe hard disks or microcomputer floppy disks until the late 1980s. GCR is a modified form of a NRZI code, but necessarily with a higher transition density.
Digital Linear Tape (DLT; previously called CompacTape) is a magnetic-tape data storage technology developed by Digital Equipment Corporation (DEC) from 1984 onwards. In 1994, the technology was purchased by Quantum Corporation, who manufactured drives and licensed the technology and trademark. A variant with higher capacity is called Super DLT (SDLT). The lower cost "value line" was initially manufactured by Benchmark Storage Innovations under license from Quantum. Quantum acquired Benchmark in 2002.
DECtape, originally called Microtape, is a magnetic tape data storage medium used with many Digital Equipment Corporation computers, including the PDP-6, PDP-8, LINC-8, PDP-9, PDP-10, PDP-11, PDP-12, and the PDP-15. On DEC's 32-bit systems, VAX/VMS support for it was implemented but did not become an official part of the product lineup.
Quarter inch cartridge tape is a magnetic tape data storage format introduced by 3M in 1972, with derivatives still in use as of 2016. QIC comes in a rugged enclosed package of aluminum and plastic that holds two tape reels driven by a single belt in direct contact with the tape. The tape was originally 1⁄4 inch (6.35 mm) wide and anywhere from 300 to 1,500 feet long. Data is written linearly along the length of the tape in one track, or written "serpentine", one track at a time, the drive reversing direction at the end of the tape, and each track's data written in the opposite direction to its neighbor. Since its introduction, it has been widely used, and many variations exist. There is a QIC trade association that publishes QIC standards which include interfaces and logical formats. To a very large extent it was the efficiency and openness of this organization which encouraged hardware and software developers to use this type of drive and media.
Linear Tape-Open (LTO), also known as the LTO Ultrium format, is a magnetic tape data storage technology used for backup, data archiving, and data transfer. It was originally developed in the late 1990s as an open standards alternative to the proprietary magnetic tape formats available at the time. Upon introduction, LTO rapidly defined the super tape market segment and has consistently been the best-selling super tape format. The latest generation as of 2021, LTO-9, can hold 18 TB in one cartridge.
The IBM 729 Magnetic Tape Unit was IBM's iconic tape mass storage system from the late 1950s through the mid-1960s. Part of the IBM 7-track family of tape units, it was used on late 700, most 7000 and many 1400 series computers. Like its predecessor, the IBM 727 and many successors, the 729 used 1⁄2 inch (13 mm) magnetic tape up to 2,400 feet (730 m) long wound on reels up to 10+1⁄2 inches (270 mm) diameter. To allow rapid tape acceleration, long vacuum columns were placed between the tape reels and the read/write heads to absorb sudden increases in tape tension which would otherwise break the tape. Write protection was provided by a removable plastic ring in the back of the tape reel.
The UNISERVO tape drive was the primary I/O device on the UNIVAC I computer. It was the first tape drive for a commercially sold computer.
The 3480 tape format is a magnetic tape data storage format developed by IBM. The tape is one-half inch (13 mm) wide and is packaged in a 4 in × 5 in × 1 in cartridge. The cartridge contains a single reel; the takeup reel is inside the tape drive.
The Massbus is a high-performance computer input/output bus designed in the 1970s by Digital Equipment Corporation (DEC). The architecture development was sponsored by Gordon Bell and John Levy was the principal architect.
IBM's first magnetic-tape data storage devices, introduced in 1952, use what is now generally known as 7-track tape. The magnetic tape is 1⁄2 inch (13 mm) wide, and there are six data tracks plus one parity track for a total of seven parallel tracks that span the length of the tape. Data is stored as six-bit characters, with each bit of the character and the additional parity bit stored in a different track.
Magnetic-tape data storage is a system for storing digital information on magnetic tape using digital recording.
The IBM 3592 is a series of enterprise-class tape drives and corresponding magnetic tape data storage media formats developed by IBM. The first drive, having the IBM product number 3592, was introduced under the nickname Jaguar. The next drive was the TS1120, also having the nickname Jaguar. As of October 2023, the latest and current drive is the TS1170. The 3592 line of tape drives and media is not compatible with the IBM 3590 series of drives, which it superseded. This series can store up to 50 TB of data (uncompressed) on a cartridge and has a native data transfer rate of up to 400 MB/s. In August 2023 IBM announced the TS1170 tape drive with 50TB cartridges, more than 2.5 times larger than LTO-9 cartridges.
A tape transport is the collection of parts of a magnetic tape player or recorder that move the tape and play or record it. Transport parts include the head, capstan, pinch roller, tape pins, and tape guide. The tape transport as a whole is called the transport mechanism.
A floppy disk is a disk storage medium composed of a thin and flexible magnetic storage medium encased in a rectangular plastic carrier. It is read and written using a floppy disk drive (FDD). Floppy disks were an almost universal data format from the 1970s into the 1990s, used for primary data storage as well as for backup and data transfers between computers.
Tape labels are identifiers given to volumes of magnetic tape.
The IBM Naval Ordnance Research Calculator (NORC) was a one-of-a-kind first-generation computer built by IBM for the United States Navy's Bureau of Ordnance. It went into service in December 1954 and was likely the most powerful computer at the time. The Naval Ordnance Research Calculator (NORC), was built at the Watson Scientific Computing Laboratory under the direction of Wallace Eckert.
The IBM 7701 Magnetic Tape Transmission Terminal was a communications device announced by IBM in 1960. It was designed to transfer the contents of a reel of magnetic tape over a leased or dial telephone circuit.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
