The Aviatik (Berg) D.I, was a single-engine, single-seater biplane fighter that was developed and manufactured by the Austro-Hungarian branch of German aircraft company Aviatik. It was also known as Berg D.I or the Berg Fighter, because it was designed by Dipl. Ing. Julius von Berg, and to distinguish it from the D.I fighter built by the parent Aviatik firm in Germany.
The Aviatik (Berg) D.I has its origins within the experimental single-seater 30.14 aircraft. Work on this prototype had commenced during early 1916; aviation author George Haddow described this aircraft as being, in comparison to the later D.I, "ugly" and "cumbersome".[4] However, it also shared many features with its subsequent production form, such as the relatively similar design of the wings. According to Haddow, it was claimed by some sources that Professor Richard Knollwer, a high-profile figure within the Austro-Hungarian Empire, has participated in the design of the 30.14.[4]
On 16 October 1916, the first flight of the prototype occurred at Aspern; however, this test flight went badly, resulting in the death of the test pilot.[citation needed] In response, further modifications to the design were made and three additional prototypes were manufactured, labeled 30.19 (for tests on the ground), 30.20 (for in-flight tests) and 30.21 (as a reserve airframe).[4] Construction of the additional test aircraft was completed during late 1916 and the test programme commenced during early 1917. During March 1917, the 30.21 suffered some damage during an eventful landing, however, it was quickly repaired and returned to the flight test programme.[4]
On the whole, the reports of test pilots who flew the prototypes were largely positive, which not only cleared the way for quantity production of the type to commence and for its adoption by the Austro-Hungarian Imperial and Royal Aviation Troops, which quickly placed multiple orders for the type.[4] The first unit to receive production examples (with two synchronized Schwarzloses, on each side of the cylinders) of the D.I was Fluggeschwader I (FLG I, later to be renamed to Flik 101G) on the Divača airfield.[citation needed]
According to Haddow, the prototypes had been largely representative of the initial production D.I aircraft, minor differences include the wings being fitted with greater stagger and the relocation of the aileron control cables. However, they did differ in terms of armament, the prototypes lacking any offensive weapons while production fighters were initially outfitted with a single unsynchronized Schwarzlose machine gun, located above the top wing to fire above the propeller.[4]
Production
The D.I was manufactured both in-house and under license by a number of subcontractors.[5] The Austrian branch of Aviatik was responsible for producing the 38, 138, 238 and 338 Series itself; all models were produced by external parties, including:
Lohner manufactured the 115 and 315 Series
Lloyd manufactured the 48, 248 and 348 Series.
MAG (Magyar Általános Gépgyár - General Hungarian Machine Works) manufactured the 84 and 92 Series
Thöne und Fiala manufactured the 101 Series
Wiener Karosserie Fabrik (WKF) (Vienna Coachwork Factory) manufactured the 184, 284 and 384 Series.
The numbers given to the different series were used to indicate various pieces of information; the first digit represented the manufacturer, the following number being used as a 'type number', which would be followed by a break and addition numbers of identify the individual fighters.[6] The main differences between the different series was in the power of Austro-Daimler engines used (185hp in the early production aircraft, 200 or 210hp in the mid-production, and 225hp in the last ones). Other key areas of change included the positioning of the machine guns, as well as various structural alterations and refinements to the radiator.[citation needed]
By 31 October 1918, 677 Aviatik (Berg) D.I airframes of all batches had been handed over to the Austro-Hungarian Imperial and Royal Aviation Troops. While ordered from Lohner and Thöne und Fiala respectively, both the 215 and 201 Series would remain unbuilt.[citation needed]
Design
The Aviatik (Berg) D.I was a single-seat biplane fighter aircraft. The pilot sat within a high-mounted central position, providing him with a high level of visibility both below and above the upper wing; to enable this seating position, the design featured an uncommonly high decking, which was faired to offer minimal resistance where possible.[7] Much of the design was shaped by the industrial circumstances of the Austro-Hungarian Empire; due to a lack of skilled labour, much of the airframe was as simplified as possible in order to make the type easier to manufacture and capable of being produced in relatively small facilities.[7]
The fuselage of the D.I was rectangular-shaped, composed of a single longeron set at each corner and spaced via bulkheads in the forward section of the fuselage, which provided a mounting point for the engine bearers.[7] Additional reinforcement was provided in the form of tubular steel diagonal struts that ran along the sides of the fuselage between the bearer and the lower wing root. Aft of the cockpit, the bulkheads were dispensed with for lighter frames composed of spruce, which were strengthened by diagonal struts; no internal wire bracing was used throughout the structure, relying upon the external plywood panels for rigidity.[7]
The wings of the D.I used an orthodox structure for the time, composed of spruce spars and leading edges.[8] Steel tubing was used for the compression members while wires were used for internal bracing. A wire-based trailing edge gave the wing a distinctive scalloped appearance.[8] The single-piece upper wing was fixed to the fuselage using the W-shaped struts, while the lower wing was bolted directly onto the side of the lower fuselage. Unblanced ailerons were only fitted onto the upper wing; these were hinged onto false spars set within the framework of the wing and actuated via a projecting lever set into the wing itself.[8] During its later service, the wings had to undergo strengthening in order to support the use of more powerful engines that were adopted during the type's production run.[8]
The D.I incorporated a relatively unconventional innovation in the form of an unusual aerofoil section.[7] Specifically, the upper camber of the wing had a pronounced reflex curvature towards its trailing edge, while the maximum depth was further aft than was standard amongst contemporary fighter aircraft. To enable this unusual construction, the rear-portion of the ribs were somewhat thin and flexible, resulting in the wing "giving" under sudden forces such as gusts of wind, but without losing equilibrium.[7] According to Haddow, these features of the wing were attributable for the D.I's high level of stability, which allegedly did little to lessen or undermine its responsiveness to control inputs, as would normally be the case amongst typical aerodynamically stable fighters.[9]
Early production D.Is were powered by a single Austro-Daimler-built engine, capable of providing 185hp; the majority of aircraft would be fitted with more powerful 200, 210, and 225hp units instead.[6] The adoption of the 225hp engine proved to be too powerful for the airframe, requiring various changes to increase structural strength, particularly within the wing area. Regardless of the engine power, a standardised two-bladed Knoller-Jaray-built propeller was adopted, although an unusual four-bladed unit was used on a minority of aircraft (confirmed on serial number 138.106) in its place.[6]
The majority of aircraft were fitted with a car-type radiator mounted in the aircraft's nose; two different variants were used, a more common rounded-top model and a more angular flat-top unit. Alternatively, some D.Is were provided with a twin-block radiator mounted one above the other on the forward fuselage, which enabled a more streamlined nose to be adopted.[6] Regardless of the version of the radiator used, cooling was a persistent issue suffered by the type. As a result, many D.Is would be flown with the engine cowling being completely removed by ground crews; a solution to the overheating issue was fitted on later-built aircraft in the form of a simple low-cut fringe cowl that kept the engine cylinders exposed and an elongated block radiator fixed onto the leading edge of the wing.[10]
The D.I was fitted with various armaments. It was initially armed with a single Schwarzlose machine gun, which was mounted onto braces set into the upper fuselage; this arrangement was clear of the propeller blades yet still allowed for easy in-flight access to the breach mechanism.[11] Ammunition was stored in a drum within the fuselage decking and belt-fed to the gun via a purpose-built conduit. However, this arrangement was commonly judged to have been outmoded by the time that the D.I was entering service; accordingly, a new armament arrange was soon adopted. A twin Schewarzlose gun arrangement, which featured synchronization gear as to allow the rounds to pass directly between the propeller blades without striking them; however, the locally produced interrupter mechanism was found to be unreliable in service when the engine was run at certain speeds.[11] In spite of the issue, which made the guns prone to striking the propeller blades, this newer armament arrangement was rolled out. Further changes, including the guns being set further back, were also made late on into production.[12]
Operational service
In many respects, the D.I was allegedly proved to have been good combat aircraft amongst its contemporaries. It was a reasonably fast aircraft, possessing excellent flying characteristics and maneuverability, and could reach higher altitudes than most of its adversaries. In addition, the D.I was provided with a roomy and comfortable cockpit which gave a good field of view.
Despite those desirable features, the new Aviatik fighter wasn't greeted with enthusiasm when it entered service in autumn 1917, as the type also had some serious defects which didn't endear it to its pilots.[13] The early aircraft had structural deficiencies and their machine guns were installed beyond the reach of the pilot so that when they jammed, there was nothing the pilot could do about it. These problems were later rectified with the strengthening of the airframe and the repositioning of the guns. While the original Aviatik D-I design by Julius von Berg was sound, the Series 115 aircraft license-produced by the Lohner firm at Wien-Floridsdorf were notorious for failures along the wing trailing edges in high-speed maneuvers, as Lohner had deviated from Aviatik specifications by employing thinner, lighter wing ribs. The main cause of complaints was the engine's tendency to overheat far too easily. To alleviate these cooling problems, operational units tended to fly their aircraft without the engine's top panels, and sometimes the side panels were also left off.[14]
The Austro-Hungarian aviation units used the D.I widely until the end of the First World War on Eastern, Italian and Balkan fronts, mainly as an escort for reconnaissance aircraft, as most of the fighter units preferred the Albatros D.III for air superiority. During 1918, a single D.I was forced down in an undamaged state on the Italian font; this undamaged example was later shipped back to the United Kingdom, where it was subject to an extensive evaluation, which found it to be comparable to its various peers of the time, being particularly light, strong, and simplistic in terms of its construction. The captured aircraft was later put on public display in London.[8]
Variants
The D.II was a version of the D.I with a cantilever lower wing. The model went into production in late 1918 in two Series (39 and 339), but the production aircraft were too late for operational service. The D.III high-altitude version with a 230hp Hiero engine and the Dr.Itriplane development remained as prototypes only.
The Fokker D.VII was a German World War I fighter aircraft designed by Reinhold Platz of the Fokker-Flugzeugwerke. Germany produced around 3,300 D.VII aircraft in the second half of 1918. In service with the Luftstreitkräfte, the D.VII quickly proved itself to be a formidable aircraft. The Armistice ending the war specifically required, as the fourth clause of the "Clauses Relating to the Western Front", that Germany was required to surrender all D.VIIs to the Allies. Surviving aircraft saw much service with many countries in the years after World War I.
The Albatros D.III was a biplane fighter aircraft used by the Imperial German Army Air Service (Luftstreitkräfte) during World War I. A modified licensed version was built by Oeffag for the Austro-Hungarian Air Service (Luftfahrtruppen). The D.III was flown by many top German aces, including Wilhelm Frankl, Erich Löwenhardt, Manfred von Richthofen, Karl Emil Schäfer, Ernst Udet, and Kurt Wolff, and Austro-Hungarians like Godwin von Brumowski. It was the preeminent fighter during the period of German aerial dominance known as "Bloody April" 1917.
The Albatros D.II was a German fighter aircraft used during World War I. After a successful combat career in the early Jagdstaffeln, it was gradually superseded by the Albatros D.III.
The Fokker D.I was a development of the D.II fighter. The D.I was also flown in Austro-Hungarian service as a fighter trainer aircraft under the designation B.III. Confusing the matter further, both the D.II and D.I arrived at the Front in German service at similar times, in July–August 1916. The main designer was Martin Kreutzer.
The Austro-Hungarian Aviation Troops or Imperial and Royal Aviation Troops were the air force of the Austro-Hungarian Empire until the empire's demise in 1918; it saw combat on both the Eastern Front and Italian Front during World War I.
The Halberstadt D.II was a biplane fighter aircraft developed and manufactured by German aircraft company Halberstädter Flugzeugwerke.
The Hansa-Brandenburg C.I, also known as Type LDD, was a 2-seater armed single-engine reconnaissance biplane designed by Ernst Heinkel, who worked at that time for the parent company in Germany. The C.I had similarities with the earlier B.I, including inward-sloping interplane bracing struts. Like other early-war Austro-Hungarian reconnaissance aircraft, such as C-types of Lloyd or Lohner, the Type LDD had a communal cockpit for its crew.
The Hansa-Brandenburg CC was a single-seat German fighter flying boat of World War I. It was used by both the Kaiserliche Marine and the Austro-Hungarian Navy.
The Hansa-Brandenburg D.I, also known as the KD was a German fighter aircraft of World War I. Despite poor handling characteristics it was put into service by Austria-Hungary, where some aircraft served until the end of the war.
The Lohner L was a reconnaissance flying boat produced in Austria-Hungary during World War I. It was a two-bay biplane of typical configuration for the flying boats of the day, with its pusher engine mounted on struts in the interplane gap. The pilot and observer sat side by side in an open cockpit, and both the upper and lower sets of wings featured sweepback.
The Aviatik (Berg) D.II, the prototypes of which were known as Aviatik 30.22 and Aviatik 30.38, was an Austro-Hungarian sesquiplane fighter aircraft prototype towards the end of the First World War.
The Knoller C.II was a reconnaissance aircraft built in Austria-Hungary during World War I for use by the Austro-Hungarian army.
Oberleutnant Frank Linke-Crawford, was the fourth-ranking ace of the Austro-Hungarian Air Force during World War I, with 27 victories.
The Rumpler D.I was a fighter-reconnaissance aircraft produced in Germany at the end of World War I. It was a conventional single-bay biplane with wings of unequal span braced by I-struts. It featured an open cockpit and a fixed, tailskid undercarriage. The upper wing was fitted with aerodynamically balanced ailerons and fuselage had an oval cross-section.
The Aviatik C.I, the prototypes of which were known as Aviatik 30.14, Aviatik 30.15 and Aviatik 30.16, was an Austro-Hungarian 2-seat reconnaissance aircraft produced from 1917.(Note: the is not part of the designation, but used to disambiguate from the German-built Aviatik aircraft with the same designation.)
The Lohner Type AA were a series of prototype fighters built during World War I. The program would eventually be cancelled due to inherent instability concerns of the design.
The Lloyd 40.08 Luftkreuzer was a three engine triplane bomber type built during World War I. The design was proven to be ineffective and development did not proceed past the prototype stage.
The Aviatik 30.24 was a prototype Austro-Hungarian triplane fighter built by Aviatik in World War I.
The Knoller D.I series 70 was a prototype fighter aircraft built in the Austro-Hungarian Empire during World War I for use by the Kaiserliche und Königliche Luftfahrtruppen (KuKLFT).
The Lohner M was a reconnaissance flying boat produced in small numbers in Austria-Hungary during World War I. It was a two-bay biplane of typical configuration for the flying boats of the day, with its pusher engine mounted on struts in the interplane gap. The pilot and observer sat side by side in an open cockpit, and both the upper and lower sets of wings featured sweepback.
↑ The German parent company of Aviatik built the Halberstadt D.II under licence as the Aviatik D.I. This was later redesignated Halberstadt D.II(Av) when the German military changed its nomenclature, however the D.I designation was never reused. The Aviatik (Berg) D.I designation was in a different sequence, used by the Austro-Hungarian military.
Munson, Kenneth. Fighters, Attack and Training Aircraft 1914-19 (The Pocket Encyclopedia of World Aircraft in Colour ). London: Bounty Books, 2004. ISBN0-7537-0916-3.
Varriale, Paolo (2016). Aviatik (Berg) D.I at War!. Windsock Datafile. Vol.171. Berkhampstead, UK: Albatros Productions. ISBN978-1-906798-46-8.
External links
Wikimedia Commons has media related to Aviatik D.I.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
