The BC548 is a general-purpose NPN bipolar junction transistor commonly used in European and American electronic equipment. It is notably often the first type of bipolar transistor hobbyists encounter and is often featured in designs in hobby electronics magazines where a general-purpose transistor is required. [1] [2] [3] The BC548 is low in cost [4] [3] and widely available. [5]
The BC548 is a part of a family of NPN and PNP epitaxial silicon transistors that originated with the metal-cased BC108 family of transistors. The BC548 is the modern plastic-packaged BC108; [6] the BC548 article at the Radiomuseum website [7] describes the BC548 as a successor to the BC238 and differing from the BC108 in only the shape of the package. Datasheets for the BC548 give specifications that are identical to, or exceed, those of the BC108, BC148 and BC238 predecessors. Thus the BC548 (or BC546 to 550) is a valid substitute in any circuit designed for the older BC108 (or BC148), which includes many Mullard and Philips published designs.[ citation needed ]
The BC548 is supplied in a standard TO-92 3-pin package. The assignment of transistor elements (b,c,e) to leads, i.e. the "pinout", uses the same convention used by some - but not all - other TO-92 devices. As viewed in the top-right image, going from left to right, the pinout is as follows:
Sometimes the middle pin is supplied bent to form a triangle of leads (as found in TO-18 case transistors and, for example, the ZTX108-L) to match the pinout of the BC108 more exactly.
The BC548 part number is assigned by Pro Electron, which allows many manufacturers to offer electrically and physically interchangeable parts under one identification. Devices registered to this Pro Electron number must have the following minimum performance characteristics: [9]
The BC548 was released with, and often is found together in datasheets with, the BC547 (higher voltage) and BC549 (lower noise) devices, that correspond to the original BC107 and BC109 variants of the BC108. This group of NPN transistors share many specifications and characteristic curves, but differ in voltage ratings - the BC546 and BC547 are essentially the same as the BC548 but selected with higher breakdown voltages, while the BC549 is a low noise version, and the BC550 is both high-voltage and low-noise. [10] The BC556 to BC560 are the PNP counterparts of the BC546 to BC550, respectively. See the BC108 family for a table of these differences, and comparisons with predecessor types.
Some manufacturers specify their parts with higher ratings, for example the Fairchild 1997 datasheet (547ABC, Rev B) for the BC547, sourced from Process 10 gave 500mA as the maximum collector current, while their datasheets dated 2002 have dropped the current rating to the standard 100mA. [11] The power rating (in free air at 25 °C) is also subject to variation, from 500 mW to 625 mW; the latter now being the most common. There is lot of variation in the ft-transition maximum frequency from manufacturer to manufacturer.
The type number of any of the devices in this "family" may be followed by a letter, "A" to "C", indicating devices that have been selected that fall within a narrow range of gain (hFE). The same letters are used for this purpose in several other European transistors, and is similar in principle to the "Yellow", "Blue" (and so on) gain groupings in Japanese transistors, but should not be confused with the "A" suffix used with some American (JEDEC) devices, such as the 2N2222A, to indicate a variety of differences or enhancements over the base type.
The BC548 is available in three different gain groups:.
So a BC548 might have a current gain anywhere between 110 and 800, but the gain of a BC548A would be within the range of 110 to 220.
Notes: Some manufacturers place slightly different limits on the gain groups, for example the "B" group has been quoted as 220-475 in a Philips 1997 datasheet. The BC547 variant rarely is available in the "C" gain group, and the BC549 rarely in the "A" gain group.
The PNP counterparts of the BC546 to BC550 are the BC556 to BC560 respectively, i.e. the type numbers are higher by ten.
The BC558 is the PNP version of the BC548, and has higher voltage versions: BC556 and BC557, and lower noise versions: BC559 and BC560.
The surface-mount package versions are the BC846 to BC850 (and PNP versions: BC856 to BC860).
A transistor is a semiconductor device used to amplify or switch electrical signals and power. The transistor is one of the basic building blocks of modern electronics. It is composed of semiconductor material, usually with at least three terminals for connection to an electronic circuit. A voltage or current applied to one pair of the transistor's terminals controls the current through another pair of terminals. Because the controlled (output) power can be higher than the controlling (input) power, a transistor can amplify a signal. Some transistors are packaged individually, but many more are found embedded in integrated circuits.
Transistor–transistor logic (TTL) is a logic family built from bipolar junction transistors. Its name signifies that transistors perform both the logic function and the amplifying function, as opposed to resistor–transistor logic (RTL) or diode–transistor logic (DTL).
A bipolar junction transistor (BJT) is a type of transistor that uses both electrons and electron holes as charge carriers. In contrast, a unipolar transistor, such as a field-effect transistor, uses only one kind of charge carrier. A bipolar transistor allows a small current injected at one of its terminals to control a much larger current flowing between two other terminals, making the device capable of amplification or switching.
In electronics, a multi-transistor configuration called the Darlington configuration is a circuit consisting of two bipolar transistors with the emitter of one transistor connected to the base of the other, such that the current amplified by the first transistor is amplified further by the second one. The collectors of both transistors are connected together. This configuration has a much higher current gain than each transistor taken separately. It acts like and is often packaged as a single transistor. It was invented in 1953 by Sidney Darlington.
In electronics, emitter-coupled logic (ECL) is a high-speed integrated circuit bipolar transistor logic family. ECL uses an overdriven BJT differential amplifier with single-ended input and limited emitter current to avoid the saturated region of operation and its slow turn-off behavior. As the current is steered between two legs of an emitter-coupled pair, ECL is sometimes called current-steering logic (CSL), current-mode logic (CML) or current-switch emitter-follower (CSEF) logic.
The Schottky diode, also known as Schottky barrier diode or hot-carrier diode, is a semiconductor diode formed by the junction of a semiconductor with a metal. It has a low forward voltage drop and a very fast switching action. The cat's-whisker detectors used in the early days of wireless and metal rectifiers used in early power applications can be considered primitive Schottky diodes.
A TRIAC is a three terminal electronic component that conducts current in either direction when triggered. The term TRIAC is a genericised trademark.
Pro Electron or EECA is the European type designation and registration system for active components.
In electronics, derating is the operation of a device at less than its rated maximum capability in order to prolong its life. Typical examples include operation below the maximum power rating, current rating, or voltage rating.
The TO-92 is a widely used style of semiconductor package mainly used for transistors. The case is often made of epoxy or plastic, and offers compact size at a very low cost.
A power MOSFET is a specific type of metal–oxide–semiconductor field-effect transistor (MOSFET) designed to handle significant power levels. Compared to the other power semiconductor devices, such as an insulated-gate bipolar transistor (IGBT) or a thyristor, its main advantages are high switching speed and good efficiency at low voltages. It shares with the IGBT an isolated gate that makes it easy to drive. They can be subject to low gain, sometimes to a degree that the gate voltage needs to be higher than the voltage under control.
The 2N3055 is a silicon NPN power transistor intended for general purpose applications. It was introduced in the early 1960s by RCA using a hometaxial power transistor process, transitioned to an epitaxial base in the mid-1970s. Its numbering follows the JEDEC standard. It is a transistor type of enduring popularity.
In electronics, the Sziklai Pair, also known as a complementary feedback pair, is a configuration of two bipolar transistors, similar to a Darlington pair. In contrast to the Darlington arrangement, the Sziklai Pair has one NPN and one PNP transistor, and so it is sometimes also called the "complementary Darlington". The configuration is named for its inventor, George C. Sziklai.
Texas Instruments Power, known more popularly by its acronym TIP, is a series of bipolar junction transistors manufactured by Texas Instruments. The series was introduced in the 1960s, and still sees some use today due to their simplicity, their durability, and their ease of use. A Texas Instruments catalog in 1966 lists the TIP04 and TIP14 part numbers.
In electronics, TO-3 is a designation for a standardized metal semiconductor package used for power semiconductors, including transistors, silicon controlled rectifiers, and, integrated circuits. TO stands for "Transistor Outline" and relates to a series of technical drawings produced by JEDEC.
The 2N3904 is a common NPN bipolar junction transistor used for general-purpose low-power amplifying or switching applications. It is designed for low current and power, medium voltage, and can operate at moderately high speeds.
The 2N2222 is a common NPN bipolar junction transistor (BJT) used for general purpose low-power amplifying or switching applications. It is designed for low to medium current, low power, medium voltage, and can operate at moderately high speeds. It was originally made in the TO-18 metal can as shown in the picture.
The 2N2907 is a commonly available PNP bipolar junction transistor used for general purpose low-power amplifying or switching applications. It is designed for low to medium current, low power, medium voltage, and can operate at moderately high speeds. This transistor was made by several manufacturers; Texas Instruments released a data sheet for their version of this part dated March 1973. An "A" suffix indicates a slightly higher breakdown voltage. These transistors have an enduring popularity with electronics hobbyists.
The 2N3906 is a commonly used PNP bipolar junction transistor intended for general purpose low-power amplifying or switching applications. It is designed for low electric current and power and medium voltage, and can operate at moderately high speeds.
The BC107, BC108 and BC109 are general-purpose low power silicon NPN bipolar junction transistors found very often in equipment and electronics books/articles from Europe, Australia and many other countries from the 1960s. They were created by Philips and Mullard in 1963 and introduced in April 1966. Initially in metal (TO-18) packages, the range expanded over time to include other package types, higher voltage ratings, and a better selection of gain groupings, as well as complementary PNP types. Some manufacturers have specified their parts with a higher power dissipation rating (Ptot) than others.