CVV 8 Bonaventura

Last updated
Bonaventura
CVV 8 Bonaventura at Volandia.jpg
RoleTwo seat competition glider
National origin Italy
ManufacturerCentro Volo a Vela, Milan (CVV)
DesignerErmenegildo Preti
First flight29 December 1957
Number built15

The CVV 8 Bonaventura (English: Good Adventure) was a two-seat competition glider designed and built in Italy during the 1950s. Fifteen were produced.

Contents

Design and development

The Bonaventura was designed at the Centro Volo a Vela (CVV), or Experimental Soaring Centre, of the Royal Polytechnic of Milan by Gildo Preti; though construction was started in 1952, the prototype was not completed until 1957. The first flight took place on 14 December that year. It was named after the fortunate eponymous protagonist of an Italian children's comic strip, Signor Bonaventura. [1]

The Bonaventura is an all wood aircraft with a 19 m (62 ft 4 in) span, shoulder mounted wing, built around a single spar. Its airfoil section is from the NACA laminar flow 6-series. Ahead of the spar, the wing is skinned with plywood laid with its grain at 45° to the centre line for strength; this goes around the nose of the wing, forming a torsion resisting D-box. Behind the spar the wing is fabric covered. The plan is essentially double straight tapered, though a short centre section has a leading edge normal to the fuselage centre line, and a trailing edge slightly more forward sweep than outboard. Long, narrow chord ailerons occupy about half the span; airbrakes are placed immediately inboard of the ailerons at mid-chord. These consist of seven rotating blades on each side which project both above and below the wing when deployed, counter-rotating away on chord-wise axes. [1]

The fuselage is a ply shell, ovoid in cross section and built around a series of frames and stringers. The tandem seats are enclosed ahead of the wing leading edge under a starboard hinged, continuous canopy. The Bonaventura has no wheeled undercarriage, but took off from a wheeled, drop-off dolly and landed on a simple, rubber sprung skid extending from nose to mid chord, aided by a sprung tail skid. The fuselage becomes slim towards the tail, where the double straight tapered horizontal tail is mounted on top of it, far enough forward that its trailing edge is at the rudder hinge. The elevators are fabric covered and the starboard one carries a trim tab. Fin and rudder are also straight tapered and the tall, fabric covered, unbalanced rudder reaches down to the keel. [1]

Operational history

Two Bonaventura prototypes were built by CVV, followed by a short production run of thirteen from Avionautica Rio. [1] These went to Italian gliding clubs. Three Bonaventuras survive in museum collections, though none were on public display in 2010. [2]

Specifications

Data from Italian Vintage Sailplanes [1]

General characteristics

Performance

Related Research Articles

The Akaflieg Darmstadt D-34 sailplanes were a series of experimental single seat sailplanes, designed at the University of Darmstadt in the 1950s and early 1960s to explore the structural and aerodynamic advantages of the then emerging plastics and composite materials.

The Kirigamine Mita is a training glider, seating two in tandem, designed in Japan in the early 1960s. A modified version, first flown in 1966, was produced in modest numbers.

<span class="mw-page-title-main">CVV-4 Pellicano</span> Type of aircraft

The CVV-4 Pellicano was a single seat Italian glider designed for a competition to select an aircraft for the 1940 Olympic Games. The DFS Olympia Meise was preferred to it after the trials in Italy in 1939.

<span class="mw-page-title-main">Ciani Urendo</span> Type of aircraft

The Ciani EC 38/56 Urendo, or SSVV EC 38/56 Urendo is an Italian tandem-seat training glider from the 1950s. Four were built, one winning the Italian National Championships in 1959. Another, restored, still flies.

The CVV1 Pinguino was a single seat, high performance glider designed and built in Italy in the mid-1930s, the first of a series of gliders from the Milan Polytechnic. It did not go into production.

The CVV 2 Asiago is a simple, single seat glider designed and built in Italy in the mid-1930s, the second of a series of gliders from the Milan Polytechnic and the first go into production.

The CVV 3 Arcore was a single seat competition glider designed and built in Italy in the late 1930s, a development of the CVV 1 Pinguino. It participated in several national gliding competitions in the short period before the outbreak of World War II.

The CVV 5 Papero was a single seat competition glider designed and built in Italy in the late 1930s, a development of the CVV 4 Pellicano.

The CVV 7 Pinocchio was a single seat competition glider designed and built in Italy, first flown in 1952 though designed in 1940. Only one was built.

The Aeronautica Lombarda AL-3 was an Italian sailplane, designed and built in 1939 to take part in the Olympic sailplane competition. It did so but was not successful.

The Pagliani Vittoria was a single-seat glider built in Italy during Second World War. Only one was constructed.

The CVT1 Zigilo was a single-seat, 12-metre-span (39 ft) Italian training glider designed and built in Italy in the 1950s. Only one was completed.

The IIL IS-5 was a single seat, high performance sailplane designed by Iosif Șilimon and built in Romania in 1960.

The IIL IS-7 was a two-seat, sailplane designed by Iosif Șilimon and built in Romania in the late 1950s. Only one prototype was built.

The IIL IS-8 was a two-seat sailplane designed by Iosif Șilimon and built in Romania in 1960. They served with Romanian gliding clubs.

The IIL IS-10 was a high-performance, single-seat glider, designed and built in Romania in the early 1960s. It was the first Romanian aircraft to use laminar flow airfoils.

The IIL IS-11 was an aerobatic, single seat glider, designed and built in Romania in 1959. It was built in small numbers.

The Schneider ES-56 Nymph was a short span, Australian glider with a laminar flow wing, built in the 1950s. Only four were built.

The Merville SM.31 is a French high performance glider with a laminar flow wing, first flown in 1960. Only one was built.

<span class="mw-page-title-main">Oberlerchner Mg 19</span> Type of aircraft

The Oberlerchner Mg 19 Steinadler is an Erwin Musger designed two seat tandem trainer glider built in Austria and first flown in 1951. Several examples of this successful aircraft, which competed in the two seat class at two World Gliding Championships in the 1950s, were still flying in 2000.

References

  1. 1 2 3 4 5 Pedrielli, Vincenzo; Camastra, Francesco (2011). Italian Vintage Sailplanes. Königswinter: EQIP Werbung & Verlag GmbH. pp. 111, 128–9. ISBN   978-3-9808838-9-4.
  2. Ogden, Bob (2009). Aviation Museums and Collections of Mainland Europe. Air Britain (Historians). ISBN   978-0-85130-418-2.
  3. 1 2 "CVV 8 Bonaventura" . Retrieved 30 November 2012.
  4. Lednicer, David. "The Incomplete Guide to Airfoil Usage". m-selig.ae.illinois.edu. Retrieved 16 April 2019.