Facing and trailing

Last updated

Turnouts facing and trailing. Note that this diagram is for left-hand traffic; for right-hand traffic, "F" and "T" would be swapped. Turnouts Facing & Trailing.jpg
Turnouts facing and trailing. Note that this diagram is for left-hand traffic; for right-hand traffic, "F" and "T" would be swapped.

Facing or trailing are railway turnouts (or 'points' in the UK) in respect to whether they are divergent or convergent. When a train traverses a turnout in a facing direction, it may diverge onto either of the two routes. When travelled in a trailing direction, the two routes converge onto each other. [1] [2] [3]

Contents

Diamond crossings

Fixed diamond crossings (with no moving parts) count as trailing points in both directions, although in very exceptional circumstances such as propelling a train in reverse over fine angle diamond crossings they can derail wagons as they bunch up.

Switched diamonds, which contain two stub turnouts in disguise, count as facing turnouts in both directions and are also known as moveable angles (UK).

Moveable crossings

Fixed V-crossings are trailable in both directions. Moveable crossings are effectively facing in both directions and must be correctly aligned.

Stub switches

Stub switches are effectively facing in both directions and must be correctly aligned.

Double junctions

Double junctions are now configurable in a number of different ways, whereby the number of facing and trailing turnouts vary.

Goods siding

The goods siding on a double line (in the above diagram) uses two trailing points and a diamond. It can be shunted by trains in either direction.

This was widely done in New South Wales, though later on the diamond crossing was replaced with a pair of ladder crossovers; such as:

Related Research Articles

<span class="mw-page-title-main">Railroad switch</span> Mechanism that allows trains to be guided from one track to another

A railroad switch (AE), turnout, or [set of] points (CE) is a mechanical installation enabling railway trains to be guided from one track to another, such as at a railway junction or where a spur or siding branches off.

<span class="mw-page-title-main">Railway signal</span> Visual signal device for railway engineers

A railway signal is a visual display device that conveys instructions or provides warning of instructions regarding the driver’s authority to proceed. The driver interprets the signal's indication and acts accordingly. Typically, a signal might inform the driver of the speed at which the train may safely proceed or it may instruct the driver to stop.

<span class="mw-page-title-main">Railway signalling</span> The principle of signals used to control railway traffic

Railway signalling (BE), also called railroad signaling (AE), is a system used to control the movement of railway traffic. Trains move on fixed rails, making them uniquely susceptible to collision. This susceptibility is exacerbated by the enormous weight and inertia of a train, which makes it difficult to quickly stop when encountering an obstacle. In the UK, the Regulation of Railways Act 1889 introduced a series of requirements on matters such as the implementation of interlocked block signalling and other safety measures as a direct result of the Armagh rail disaster in that year.

<span class="mw-page-title-main">Wye (rail)</span> Y-shaped rail junction

In railroad structures, and rail terminology, a wye or triangular junction is a triangular joining arrangement of three rail lines with a railroad switch at each corner connecting to the incoming lines. A turning wye is a specific case.

<span class="mw-page-title-main">Token (railway signalling)</span> Method of controlling single line railways

In railway signalling, a token is a physical object which a train driver is required to have or see before entering onto a particular section of single track. The token is clearly endorsed with the names of the section to which it belongs. A token system is more commonly used for single lines because of the greater risk of collision in the event of a mistake being made by a signaller or traincrew, than on double lines.

<span class="mw-page-title-main">Derailment</span> Form of train incident

In rail transport, a derailment occurs when a rail vehicle such as a train comes off its rails. Although many derailments are minor, all result in temporary disruption of the proper operation of the railway system and they are a potentially serious hazard.

<span class="mw-page-title-main">Colwich rail crash</span> 1986 rail crash at Colwich Junction, England

The Colwich rail crash occurred on the evening of Friday 19 September 1986 at Colwich Junction, Staffordshire, England. It was significant in that it was a high speed collision between two packed express trains. One driver was killed, but no passengers died because of the great strength of the rolling stock involved, which included examples of Mk1, Mk2 and Mk3 coaches.

<span class="mw-page-title-main">Siding (rail)</span> Type of railway track

A siding, in rail terminology, is a low-speed track section distinct from a running line or through route such as a main line, branch line, or spur. It may connect to through track or to other sidings at either end. Sidings often have lighter rails, meant for lower speed or less heavy traffic, and few, if any, signals. Sidings connected at both ends to a running line are commonly known as loops; those not so connected may be referred to as single-ended or dead-end sidings, or stubs.

<span class="mw-page-title-main">Centralized traffic control</span>

Centralized traffic control (CTC) is a form of railway signalling that originated in North America. CTC consolidates train routing decisions that were previously carried out by local signal operators or the train crews themselves. The system consists of a centralized train dispatcher's office that controls railroad interlockings and traffic flows in portions of the rail system designated as CTC territory. One hallmark of CTC is a control panel with a graphical depiction of the railroad. On this panel, the dispatcher can keep track of trains' locations across the territory that the dispatcher controls. Larger railroads may have multiple dispatcher's offices and even multiple dispatchers for each operating division. These offices are usually located near the busiest yards or stations, and their operational qualities can be compared to air traffic towers.

<span class="mw-page-title-main">Radio Electronic Token Block</span> Railway signalling system

Radio Electronic Token Block is a system of railway signalling used in the United Kingdom. It is a development of the physical token system for controlling traffic on single lines. The system is slightly similar to North American Direct Traffic Control, which unlike RETB does not have a cab display unit.

<span class="mw-page-title-main">Passing loop</span> Place on a railway where trains can pass each other

A passing loop or passing siding is a place on a single line railway or tramway, often located at or near a station, where trains or trams travelling in opposite directions can pass each other. Trains/trams going in the same direction can also overtake, provided that the signalling arrangement allows it. A passing loop is double-ended and connected to the main track at both ends, though a dead end siding known as a refuge siding, which is much less convenient, can be used. A similar arrangement is used on the gauntlet track of cable railways and funiculars, and in passing places on single-track roads.

<span class="mw-page-title-main">Swingnose crossing</span> Type of train guidance mechanism

A swingnose crossing or moveable point frog is a device used at a railway turnout to eliminate the gap at the common crossing which can cause damage and noise.

<span class="mw-page-title-main">Catch points</span> Railway points used as safety devices

Catch points and trap points are types of points which act as railway safety devices. Both work by guiding railway carriages and trucks from a dangerous route onto a separate, safer track. Catch points are used to derail vehicles which are out of control on steep slopes. Trap points are used to protect main railway lines from unauthorised vehicles moving onto them from sidings or branch lines. Either of these track arrangements may lead the vehicles into a sand drag or safety siding, track arrangements which are used to safely stop them after they have left the main tracks.

Rail transport – means of conveyance of passengers and goods by way of wheeled vehicles running on rail tracks consisting of steel rails installed on sleepers/ties and ballast.

<span class="mw-page-title-main">Level junction</span> Type of railway junction

A level junction is a railway junction that has a track configuration in which merging or crossing railroad lines provide track connections with each other that require trains to cross over in front of opposing traffic at grade.

Australian railway signalling varies between the States of Australia, because the individual States are responsible for the railway systems within their own borders, with, historically, no need to co-ordinate between states except at the boundaries.

<span class="mw-page-title-main">Double junction</span> Railway junction

A double junction is a railway junction where a double-track railway splits into two double track lines. Usually, one line is the main line and carries traffic through the junction at normal speed, while the other track is a branch line that carries traffic through the junction at reduced speed.

<span class="mw-page-title-main">Axle counter</span>

An axle counter is a system used in railway signalling to detect the clear or occupied status of a section of track between two points. The system generally consists of a wheel sensor and an evaluation unit for counting the axles of the train both into and out of the section. They are often used to replace a track circuit.

<span class="mw-page-title-main">Lever frame</span> Railway signalling system component

Mechanical railway signalling installations rely on lever frames for their operation to interlock the signals, track locks and points to allow the safe operation of trains in the area the signals control. Usually located in the signal box, the levers are operated either by the signalman or the pointsman.

<span class="mw-page-title-main">Application of railway signals</span> Overview of train traffic management

The application of railway signals on a rail layout is determined by various factors, principally the location of points of potential conflict, as well as the speed and frequency of trains and the movements they require to make.

References

  1. "Figure 2.12. Facing- and Trailing-Point Movements". Integrated Publishing. Retrieved June 15, 2019.
  2. "facing-point switch". Merriam-Webster. Retrieved June 15, 2019.
  3. Adams, Braman Blanchard; Hitt, Rodney (1908). The Railroad Signal Dictionary. The Railway Gazette for Railway Signal Association. p.  12 via Internet Archive.