The Grandfey-Viaduct is on the railway line from Bern to Fribourg and is one of the largest bridges in Switzerland.
The Grandfey-Viaduct is on the railway line from Bern to Fribourg and is one of the largest bridges in Switzerland.
The viaduct crosses the deep and wide Saane/Sarine valley, which is cut into Molasse rock, in the hamlet of Grandfey in Granges-Paccot, about three kilometres north of Fribourg station on the way to Düdingen.
The viaduct crosses the language border between Romandy and German-speaking Switzerland (the "Röstigraben").
In 1856, the Lausanne–Fribourg–Bern Railway Company commissioned engineer Leopold Blotnitzki to carry out studies for this most complex construction project in its route network. The design was developed by a commission of four, consisting of Durbach, Karl Etzel, François Jacqmin and Wilhelm Nördlinger, as the engineer (who was then active in France under the name Nordling) was called in Stuttgart. This planning took into account the recently built Crumlin Viaduct in South Wales and the Sitter Viaduct near St. Gallen. Planning for the construction process was carried out by Ferdinand Mathieu, senior engineer of the French iron and steel company Schneider et Cie in Le Creusot, which had received the metalworking contract for the bridge. The earthwork and masonry work was carried out by the Swiss company Wirth, Studer & Co. [1]
The 343 m long and 82 m high double-track bridge built from 1857 to 1862 consisted of six vertical lattice trusses supported by large stone pillars, carrying a strong lattice girder supporting the superstructure of the rail tracks. The five central spans were each 48.75 m long and the side spans were 43.30 m long. Inside the truss there was a lane for pedestrians and small carts. Thus the Grandfey Viaduct created a new route for light land transport over the long and impassable gorge of the Saane. [1]
The masonry stone bases were up to 32 m high so that their heads were all at the same level. The flow dividers of pillars IV and V standing in the river were protected by limestone cladding against the current. [1]
The pillars consisted of 3.93 m long cast iron pipes, which were arranged on 11 levels stacked together 43.20 m high and connected by lattice-shaped wrought iron trusses and stiffened. [1]
The track base consisted of four wrought-iron lattice girders spaced 2.09 m apart, measured from their centres. The passage for the pedestrians was located between the two middle girders. [1]
The Grandfey Viaduct is considered the first bridge where Ferdinand Mathieu, senior engineer of Schneider & Cie., used the incremental launch method that he invented. In this case, the lattice girder beam that was pushed over the valley served as a crane for the construction of the first and subsequently the next pillar. [2]
1300 tons of cast iron and 700 tons of wrought iron were used for the pillars and 1250 tons of wrought iron were used for the beams. [1]
The Grandfey viaduct influenced the Busseau Viaduct in France, which was designed shortly afterwards by Nördling. It also served as a model for the Malleco Viaduct in Chile, which was also built by Schneider & Cie. from 1886 to 1890.
Because of heavier trains, the bridge was rebuilt in 1892 with a single track, which was positioned in the middle of the deck and the speed was limited to 40 km/h.
With the electrification of the Swiss Federal Railways (SBB) network, the bridge had to be strengthened to carry heavier and faster locomotives and train compositions. The Grandfey Viaduct was rebuilt in a new form from 1925 to 1927 following principles developed by the bridge construction office of the SBB, which had already been realised with the Le Day Viaduct. SBB involved Robert Maillart, the pioneer of large concrete structures in Switzerland, as an advisory engineer. Supported by pillars consisting of iron trusses completely enclosed in concrete, the bridge has six wide concrete arches that are built according to the Melan system, over the top of which runs a pedestrian walkway. The five middle arches have clear spans of 42 m. Long rows of slender arcades that carry the track bed rest on the main arches. The double row of arches gives the large structure a monumental classical form.
As a result of the construction of the Schiffenen dam, which was completed in 1964, the lower part is now filled by the water of the Schiffenensee.
The passage through the Grandfey Viaduct is one of the most beautiful points on the canton of Fribourg's network of hiking and cycling trails.
A modern sculpture by the American artist Richard Serra is located on this passage. The artwork represents an L-shaped steel girder and was created in 1987. In August 2007, the SBB had two handrails attached to the artwork for safety reasons, which were later removed. [3]
The Tay Bridge carries rail traffic across the Firth of Tay in Scotland between Dundee and the suburb of Wormit in Fife. Its span is 2.75 miles. It is the second bridge to occupy the site.
A tubular bridge is a bridge built as a rigid box girder section within which the traffic is carried. Famous examples include the original Britannia Bridge over the Menai Strait, the Conwy railway bridge over the River Conwy, designed and tested by William Fairbairn and built by Robert Stephenson between 1846 and 1850, and the original Victoria Bridge in Montreal.
The Runcorn Railway Bridge, Ethelfleda Bridge or Britannia Bridge crosses the River Mersey at Runcorn Gap between Runcorn and Widnes in Cheshire, England. It is alongside the Silver Jubilee Bridge. The bridge is recorded in the National Heritage List for England as a Grade II* Listed building.
The Murrumbidgee River railway bridge is a former railway bridge that carried the Main Southern railway line across the Murrumbidgee River in Wagga Wagga, Australia. The original bridge, erected in 1881, was replaced in 2006.
Blackfriars Bridge in London, Ontario, Canada is a wrought iron bowstring arch through truss bridge, crossing the North Thames River. The bridge was constructed in 1875 and carries single-lane vehicles, bicycles and pedestrians from Blackfriars Street to Ridout Street North.
The Castielertobel Viaduct is a single track railway bridge spanning the Castielertobelbach, and linking the municipalities of Castiel and Calfreisen, in the Canton of Graubünden, Switzerland. It was built between 1913 and 1914 for the Chur–Arosa railway, and is now owned and used by the Rhaetian Railway.
The Waldshut–Koblenz Rhine Bridge is a single-track railway bridge on the Turgi–Koblenz–Waldshut railway, between Waldshut and Koblenz AG, crossing the Rhine and the border between Germany and Switzerland. It was the first railway bridge built over the Rhine below Lake Constance. It is the only major railway bridge over the Rhine, which is completely preserved in its original condition and is one of Europe's few lattice truss bridges. It is also one of the oldest railway bridges in the world.
Fribourg/Freiburg railway station serves the municipality of Fribourg, capital of the canton of Fribourg, Switzerland. Opened in 1862, it is owned and operated by SBB-CFF-FFS.
The Prince Alfred Bridge is a wrought iron truss and timber beam partially-disused road bridge over the Murrumbidgee River and its floodplain at Middleton Drive, Gundagai, Cootamundra-Gundagai Regional Council, New South Wales, Australia. The heritage-listed road bridge was designed by William Christopher Bennett and built from 1864 to 1867 by Francis Bell. It is also known as Prince Alfred Bridge – Iron Road Bridge and Iron Bridge over Murrumbidgee River at Gundagai. The iron bridge is owned by Transport for NSW and the timber viaduct is owned by Crown Lands. The bridge was added to the New South Wales State Heritage Register on 5 July 2019 and on the Register of the National Estate on 21 March 1978.
The Caledonian Railway Bridge is a bridge crossing the River Clyde at Broomielaw in Scotland. It is adjacent to Glasgow Central Station.
A balloon flange girder or (colloquially) balloon topper is a form of vertical I-beam wrought iron plate girder, where the top flange, instead of being a simple flat plate, is extended into a hollow tube. When a girder is subjected to a positive bending moment the top flange acts in compression making a flat plate flange more susceptible to local buckling than the balloon flange is.
Meldon Viaduct is a disused railway viaduct crossing the West Okement River at Meldon, 2.5 miles (4.0 km) south-west of Okehampton, on the edge of Dartmoor in Devon, South West England. This truss bridge was constructed from wrought iron, instead of stone or brick arches. It opened in 1874 for a single track; in 1879 its width was doubled for a second track. Although regular services were withdrawn in 1968, the bridge was used for shunting by a local quarry. In the 1990s the remaining single track was removed.
Broadbottom Viaduct is a railway viaduct that spans the River Etherow between Derbyshire and Greater Manchester in England. Originally of wooden construction supported by stone piers, the timber was replaced first with wrought iron box girders, less than 20 years after the viaduct's opening, later followed by steel trusses and more supporting piers.
The Murray River railway bridge is a heritage-listed Australian railway bridge over the Murray River on the Main Southern line south of Albury in the City of Albury, New South Wales, and on the North Eastern line north of Wodonga in Victoria. The bridge was designed by John Whitton and built from 1883 to 1884 by J. S. Bennett, with iron work supplied by Westwood, Baillie, England. It is also known as the Rail Bridge over Murray River, Albury–Wodonga and the Albury Lattice Railway Bridge and Murray River Underbridge. The bridge is owned by RailCorp, and maintained by the Australian Rail Track Corporation as part of its lease of the line. It was added to the New South Wales State Heritage Register on 2 April 1999, and added to the Register of the National Estate on 18 April 1989.
The Macdonald River railway bridge is a heritage-listed railway bridge that carries the Main Northern Line across the Macdonald River located in Woolbrook, in the Walcha Shire, New South Wales, Australia. The railway bridge was designed by John Whitton as the Engineer-in-Chief for the New South Wales Government Railways and built during 1882 by J. S. Bennett, with iron work by J. & C. Brettell, Worcester, England. The railway bridge is also known as the Woolbrook rail bridge over the Macdonald River and the Woolbrook Lattice Railway Bridge. The bridge and adjacent infrastructure is owned by Transport Asset Holding Entity, an agency of the Government of New South Wales. The bridge was added to the New South Wales State Heritage Register on 2 April 1999 and was added to the Register of the National Estate on 18 April 1989.
The Macquarie River railway bridge is a heritage-listed disused railway bridge across the Macquarie River that was previously located on the Main Western line in Bathurst in the Bathurst Region local government area of New South Wales, Australia. It was built in 1876. It is also known as Bathurst Rail Bridge over Macquarie River and Bathurst – Kelso Railway Bridge. The property is owned by Transport Asset Holding Entity, an agency of the Government of New South Wales. The bridge was added to the New South Wales State Heritage Register on 2 April 1999 and was added to the Register of the National Estate on 18 April 1989.
The Dubbo rail bridge over Macquarie River – Wambuul is a heritage-listed railway bridge on the Main Western line across the Macquarie River, located west of the Dubbo central business district in New South Wales, Australia. It was designed by John Whitton as the Engineer-in-Chief for the New South Wales Government Railways. The bridge was built during 1884 by Benjamin Barnes, with ironwork by Cochrane & Co, Middlesborough, England. The railway bridge is also known as the Dubbo Lattice Railway Bridge. The property is owned by Transport Asset Holding Entity, an agency of the Government of New South Wales. The bridge was added to the New South Wales State Heritage Register on 2 April 1999 and was listed on the Register of the National Estate on 18 April 1989.
The Wolli Creek Aqueduct is a heritage-listed sewage aqueduct located at Unwin Street, Earlwood, City of Canterbury-Bankstown, New South Wales, Australia.
The Long Cove Creek railway viaducts are heritage-listed railway viaducts which carry the Main Suburban railway line over Long Cove Creek between the suburbs of Lewisham and Summer Hill in Sydney, New South Wales, Australia. The viaducts were designed and built by the New South Wales Government Railways. The property is owned by Transport Asset Holding Entity, an agency of the Government of New South Wales. It was added to the New South Wales State Heritage Register on 2 April 1999.
The Le Day viaduct is a railway viaduct in Vallorbe in the Jura-Nord vaudois District of the Swiss canton of Vaud. It stands near the hamlet of Le Day and crosses the Orbe. This has been dammed since 1955 by the Le Day dam, which lies 450 m downstream.
{{cite book}}: CS1 maint: location missing publisher (link) (PhD thesis)