The Lucas 14CUX (sometimes referred to as the Rover 14CUX) is an automotive electronic fuel injection system developed by Lucas Industries and fitted to the Rover V8 engine in Land Rover vehicles between 1990 and 1995.[1] The system was also paired with the Rover V8 by a number of low-volume manufacturers such as TVR, Marcos, Ginetta, and Morgan.
The system is also sometimes referred to as the "Rover Hot-Wire" or "Hitachi Hot-Wire", in reference to the style of airflow sensor it uses (and the sensor's manufacturer, Hitachi).[2]
History
In the mid-1980s, Lucas developed the 13CU system by revising the Bosch L-Jetronic system and adding an electronic diagnostics capability to comply with California Air Resources Board requirements. The design of the 13CU also deviated from the original L-Jetronic design in that it used a hot-wire air mass sensor rather than the Jetronic's mechanical flap sensor.
The 13CU was further developed into the 14CU, which had (among other changes) an ECU that was more physically compact. The 14CU was used in US-market Range Rovers in 1989. Both the 13CU and 14CU were designed for use with only the 3.5L version of the Rover V8.[3]
The 14CUX was the final iteration of the system, and featured upgraded injectors and (for some markets) an external diagnostic display. It also introduced the use of a "tune resistor", which is an external resistor that plugs into the harness and is sensed by the ECU to select one of five different sets of fueling data.
Hardware
A Rover V8 3.9L engine fitted with the 14CUX system
The engine control unit (ECU) of the 14CUX system is run by a Motorola MC6803U4 8-bit microprocessor, which is an uncommon variant of the otherwise ubiquitous 6803. The processor is mislabelled in the ECU, possibly to deter any reverse engineering efforts. The 14CUX determines fueling values for each bank of the V8 separately, which requires the use of two dedicated timer outputs for independent control of the fuel injectors. This requirement helped to drive the selection of the MC6803U4 part, which has three timer outputs available (in contrast to the single timer output on the standard 6803.)
Minor design updates were made to the ECU through its life, with the earlier units given the part-number prefix "PRC" and the later units "AMR".
The code and data used by the microprocessor is stored in either a 27C128 or 27C256 EPROM (depending on the revision of the ECU), which is soldered in place on most PRC units and socketed in some late PRC units as well as AMR units. Only half of the 32KB PROM space is used, so the code/data image appears twice, duplicated in the upper half.
Function
In contrast to more modern engine management systems, the 14CUX controls fuel delivery only; it does not control spark ignition. On 14CUX-equipped vehicles, the spark control is done mechanically with the use of a distributor.
When the ignition is first turned on, the ECU energizes a relay that runs the fuel pump for a short time to pressurize the fuel rail. Once the starter motor begins to turn the engine, the ECU gets a 12VDC signal that causes it to run the fuel pump again, and energize the fuel injectors. For the next several seconds, the injector pulse width is wider than normal to provide sufficient fuel for starting. Idle control is performed by adjusting a stepper-motor-driven bypass valve in the intake plenum. When the ignition is switched off, the ECU winds the bypass valve fully open to provide enough air the next time the engine is started.
To determine the amount of fuel required by the engine, the ECU reads a number of sensors measuring the following factors:
Intake air mass
Coolant temperature
Engine speed
Throttle position
Fuel temperature
Exhaust oxygen content (narrowband)
Road speed
The intake air mass is measured with a "hot-wire" mass airflow sensor: drawn in by intake manifold vacuum, air moves past an electrically heated wire filament, and the degree to which the filament is cooled indicates the mass of the airstream.
Two factors (crankshaft speed and engine load) are used to index into a two-dimensional matrix of numeric values known as the "fuel map". The value read from the map is offset by other environmental factors (such as coolant temperature). This corrected value is then used to meter fuel by pulse-width modulating the fuel injectors. Because each bank of the V8 feeds an exhaust line with its own oxygen sensor, the air/fuel ratio can be monitored and controlled for the banks independently.
The 14CUX PROM may contain up to five fuel maps, which allowed a single ROM image to contain maps for multiple target markets. In some markets, the active map is selectable by placing an external tune resistor on a particular pin of the ECU. This external map selection was disabled in the code for North American specification (NAS) vehicles.
Open loop
Above a certain engine speed or throttle position, the ECU switches to "open-loop" mode; the inputs from the exhaust lambda sensors are ignored and the mixture is enriched beyond stoichiometric for higher power and decreased engine wear.
In addition to engine speed and load conditions triggering open-loop mode, the selection of the fuel map also may force this mode. For certain fuel maps, the 14CUX firmware fuels in open-loop mode under all running conditions.
Diagnostics
The design of the 14CUX was done well in advance of the requirement (for the 1996 model year) that all passenger vehicles sold in the United States support OBD-II. As a result, the diagnostics information collected by the 14CUX is not accessible via an OBD-II-compliant interface. In lieu of an industry-standard diagnostic interface, the 14CUX is able to communicate over a serial link at non-standard voltage levels and baud rate. The reference clock for the UART runs at 1MHz and the clock divisor is set to 128, which produces a data rate of 7812.5 baud. The serial interface allows reading and writing arbitrary memory locations via a simple software protocol. Because the value from a given sensor is always stored at the same location in RAM, these sensor values can be read if the memory location is known.
The 14CUX is capable of storing diagnostic trouble codes in a 32-byte segment of its internal memory that is maintained (even while vehicle ignition is off) by applying 5VDC (regulated down from 12VDC from the vehicle's battery.) Because of this maintainer voltage, the ECU is always drawing a small amount of current. Fault codes can be cleared by disconnecting the battery for a short period of time. Diagnostic trouble codes can be retrieved from the ECU via a small electronic display referred to as the "Fault Code Display Unit". This unit contains two seven-segment displays that together show a single two-digit fault code. When connected to the 14CUX wiring harness, the ECU detects its presence and reconfigures the RDATA and TDATA lines to work as an I2C link to this device.
Applications
In addition to the Land Rover Discovery, Defender, and Range Rover, the 14CUX was used with the Rover V8 in the TVR Griffith and its sister car, the Chimaera. In the TVR applications, engines as large as 5.0L were offered; these larger displacements required the development of new fuel maps for the engine to run properly.
Between 1990 and 1993, Ginetta produced the G33 roadster, which used the 3.9L Rover V8 and 14CUX.
For model year 1996, Land Rover chose to discontinue use of the 14CUX in its products and instead used GEMS ("Generic Engine Management System"), which had been developed jointly by Lucas and SAGEM. This was done in part due to the requirement for OBD-II in the United States market. Some automakers whose products were not exported to North America (such as TVR) continued to use the 14CUX until the later discontinuation of the Rover V8 engine.
Main connector pin assignments
The ECU interfaces with the rest of the system via a 40-pin connector. When observing the connector on the ECU box itself, with the thumb latch on the left, the numbering for the connector's pins starts at 1 in the lower left-hand corner. The pin numbering continues to the right, then in an S-shape through the two other pin rows.
Pinout of the 40-pin ECU connector
Pin
Color
Name
Description/Notes
1
red/green
Air bypass valve
48-58Ω to pin 26
2
brown/orange
MAF and main relay
Input (+12VDC)
3
yellow
Throttle position sensor
5kΩ to pin 25
4
black
Ground
O2 sensor heater return (Lambda ground)
5
gray/black
Tune resistor
Some NAS vehicles do not have a pin at this position
6
yellow (or yellow/pink)
Speed transducer
To main connector (0-12V six times per revolution)
7
green/blue
Coolant temperature sensor
To brown connector
8
purple/yellow
Heated front screen
Input from main connector
9
white/light green
Diagnostic serial port
Output to 5-pin TTS connector
10
black/yellow or red
EFI warning light
Output to main connector
11
yellow/white
Even (right) bank injectors
Output
12
blue/red
Main relay
Output to main relay coil
13
yellow/blue
Odd (left) bank injectors
Output
14
black
ECM ground
-
15
brown
Ignition and main relay
Input (+12VDC always applied)
16
blue/purple
Fuel pump relay
Output to fuel pump relay coil
17
gray/yellow
Purge control valve
Output
18
white/pink
Diagnostic serial port
Input from 5-pin TTS connector
19
white/gray or white/green
Fuel pump and inertia switch
Input (+12VDC when ignition on)
20
red
Throttle potentiometer
Swings 0.29 to 5.00 VDC
21
yellow/black to yellow/green
Air conditioner compressor load
Input
22
blue/red
MAF sensor (idle trim)
-
23
unk
Left lambda sensor
Blue shielded
24
unk
Right lambda sensor
Blue shielded
25
red/black
Sensor ground
Ground side of coolant, fuel, MAP, and TP sensors
26
green/white
Air bypass valve
48-58Ω to pin 1
27
black/gray
Signal ground
-
28
blue/gray
Air bypass valve
48-58Ω to pin 29
29
orange
Air bypass valve
48-58Ω to pin 28
30
pink
Fault display data
Output to main connector
31
black/green or black/yellow
Diagnostic plug
Input
32
gray/white
Fuel temperature thermistor
Input from gray connector
33
black/gray
A/C compressor clutch relay output
-
34
orange/black
Transmission neutral switch
Input from main connector
35
blue/green
MAF sensor
0.3 to 0.6 VDC with ignition on
36
black/green
Condenser fan timer
Tall green unit (AMR 3678)
37
(n/a)
(no connection)
-
38
brown/pink
Fault display data
Output to main connector
39
white/black or white/blue
Engine speed (ignition spark input)
Harness includes 6.8KΩ resistor
40
black
ECM ground
-
Related Research Articles
The Rover V8 engine is a compact V8 internal combustion engine with aluminium cylinder block and cylinder heads, originally designed by General Motors and later re-designed and produced by Rover in the United Kingdom. It has been used in a wide range of vehicles from Rover and other manufacturers since its British debut in 1967.
The original Ford Cologne V6 is a series of 60° cast iron block V6 engines produced continuously by the Ford Motor Company in Cologne, Germany, since 1965. Along with the British Ford Essex V6 engine and the U.S. Buick V6 and GMC Truck V6, these were among the first mass-produced V6 engines in the world.
On-board diagnostics (OBD) is an automotive term referring to a vehicle's self-diagnostic and reporting capability. OBD systems give the vehicle owner or repair technician access to the status of the various vehicle sub-systems. The amount of diagnostic information available via OBD has varied widely since its introduction in the early 1980s versions of on-board vehicle computers. Early versions of OBD would simply illuminate a malfunction indicator light or "idiot light" if a problem was detected but would not provide any information as to the nature of the problem. Modern OBD implementations use a standardized digital communications port to provide real-time data in addition to a standardized series of diagnostic trouble codes, or DTCs, which allow a person to rapidly identify and remedy malfunctions within the vehicle.
Jetronic is a trade name of a manifold injection technology for automotive petrol engines, developed and marketed by Robert Bosch GmbH from the 1960s onwards. Bosch licensed the concept to many automobile manufacturers. There are several variations of the technology offering technological development and refinement.
The manifold absolute pressure sensor is one of the sensors used in an internal combustion engine's electronic control system.
A mass (air) flow sensor (MAF) is a sensor used to determine the mass flow rate of air entering a fuel-injected internal combustion engine.
An engine control unit (ECU), also commonly called an engine control module (ECM), is a type of electronic control unit that controls a series of actuators on an internal combustion engine to ensure optimal engine performance. It does this by reading values from a multitude of sensors within the engine bay, interpreting the data using multidimensional performance maps, and adjusting the engine actuators. Before ECUs, air–fuel mixture, ignition timing, and idle speed were mechanically set and dynamically controlled by mechanical and pneumatic means.
Motronic is the trade name given to a range of digital engine control units developed by Robert Bosch GmbH which combined control of fuel injection and ignition in a single unit. By controlling both major systems in a single unit, many aspects of the engine's characteristics can be improved.
OBD-II PIDs are codes used to request data from a vehicle, used as a diagnostic tool.
An air flow meter is a device that measures air flow, i.e. how much air is flowing through a tube. It does not measure the volume of the air passing through the tube, it measures the mass of air flowing through the device per unit time. Thus air flow meters are simply an application of mass flow meters for a special medium. Typically, mass air flow measurements are expressed in the units of kilograms per second (kg/s).
Renix was a joint venture by Renault and Bendix that designed and manufactured automobile electronic ignitions, fuel injection systems, electronic automatic transmission controls, and various engine sensors. Major applications included various Renault and Volvo vehicles. The name became synonymous in the U.S. with the computer and fuel injection system used on the AMC/Jeep 2.5 L I4 and 4.0 L I6 engines.
The Digifant engine management system is an electronic engine control unit (ECU), which monitors and controls the fuel injection and ignition systems in petrol engines, designed by Volkswagen Group, in cooperation with Robert Bosch GmbH.
Trionic T5.5 is an engine management system in the Saab Trionic range. It controls ignition, fuel injection and turbo boost pressure. The system was introduced in the 1993 Saab 9000 2.3 Turbo with B234L and B234R engine.
Trionic is an engine management system developed by Saab Automobile, consisting of an engine control unit (ECU) that controls 3 engine aspects:
Ignition timing,
Fuel injection
Acts as a boost controller.
Electronic Diesel Control is a diesel engine fuel injection control system for the precise metering and delivery of fuel into the combustion chamber of modern diesel engines used in trucks and cars.
The Ford EEC or Electronic Engine Control is a series of ECU that was designed and built by Ford Motor Company. The first system, EEC I, used processors and components developed by Toshiba in 1973. It began production in 1974, and went into mass production in 1975. It subsequently went through several model iterations.
The Modular Engine Management System, or MEMS, is an electronic control system used on engines in passenger cars built by Rover Group in the 1990s. As its name implies, it was adaptable for a variety of engine management demands, including electronically controlled carburetion as well as single- and multi-point fuel injection. The abbreviations "SPi" and "MPi" refer to the single-point and multi-point injection configurations, respectively.
SECU-3 is an internal combustion engine control unit. It is being developed as an open source project. Anyone can take part in the project, and can access all the information without any registrations.
Manifold injection is a mixture formation system for internal combustion engines with external mixture formation. It is commonly used in engines with spark ignition that use petrol as fuel, such as the Otto engine, and the Wankel engine. In a manifold-injected engine, the fuel is injected into the intake manifold, where it begins forming a combustible air-fuel mixture with the air. As soon as the intake valve opens, the piston starts sucking in the still forming mixture. Usually, this mixture is relatively homogeneous, and, at least in production engines for passenger cars, approximately stoichiometric; this means that there is an even distribution of fuel and air across the combustion chamber, and enough, but not more air present than what is required for the fuel's complete combustion. The injection timing and measuring of the fuel amount can be controlled either mechanically, or electronically. Since the 1970s and 1980s, manifold injection has been replacing carburettors in passenger cars. However, since the late 1990s, car manufacturers have started using petrol direct injection, which caused a decline in manifold injection installation in newly produced cars.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
