Nanotube membrane

Last updated

Nanotube membranes are either a single, open-ended nanotube(CNT) or a film composed of an array of nanotubes that are oriented perpendicularly to the surface of an impermeable film matrix like the cells of a honeycomb. 'Impermeable' is essential here to distinguish nanotube membrane with traditional, well known porous membranes. Fluids and gas molecules may pass through the membrane en masse but only through the nanotubes. For instance, water molecules form ordered hydrogen bonds that act like chains as they pass through the CNTs. This results in an almost frictionless or atomically smooth interface between the nanotubes and water which relate to a "slip length" of the hydrophobic interface. Properties like the slip length that describe the non-continuum behavior of the water within the pore walls are disregarded in simple hydrodynamic systems and absent from the Hagen–Poiseuille equation. Molecular dynamic simulations better characterize the flow of water molecules through the carbon nanotubes with a varied form of the Hagen–Poiseuille equation that takes into account slip length. [1] [2]

Contents

Transport of polystyrene particles (60 and 100 nm diameter) through single-tube membranes (150 nm) was reported in 2000. [3] Soon after, ensemble membranes consisting of multi-walled and double-walled carbon nanotubes were fabricated and studied. [4] It was shown that water can pass through the graphitic nanotube cores of the membrane at up to five magnitudes greater than classical fluid dynamics would predict, via the Hagen-Poiseuille equation, both for multiwall tubes (inner diameter 7 nm) [5] and double-wall tubes (inner diameter <2 nm). [6]

In experiments by Holt et al., [6] pure water (~1.0020 cP viscosity) was transported through three samples of double-walled carbon nanotubes in a silicon nitride matrix with varying membrane fluxes and thicknesses. These membranes were found to have enhanced flow that was more than three orders of magnitude faster than the expected for no-slip hydrodynamic flow as calculated by the Hagen–Poiseuille equation. These results for nanotubes with the 1–2 nm diameter pores corresponded to about 10–40 water molecules per nm2 per nanosecond. In a similar experiment by Mainak Majumder et al., [5] nanotubes of about 7 nm in diameter in solid polystyrene were tested for their fluid velocities. These results similarly showed that the nanotubes have long slip-planes and flow rates were found to be four to five orders of magnitude faster than conventional fluid flow predictions.

It was further demonstrated that the flow of water through carbon nanotube membranes (without filler matrix, thus flow on the outside surface of CNTs) can be controlled through the application of electric current. [7] Among many potential uses that nanotube membranes might one day be employed is the desalination of water.

Mitra et al. (8-14) pioneered a novel architecture in producing CNT based membrane. This method creates a superior membrane by immobilizing carbon nanotubes in the pores and on the membrane surface. In their work, the CNTs are immobilized into polymeric or ceramic membranes leading to the development of unique membrane structure referred to as the carbon nanotube immobilized membrane (CNIM). This was achieved by immobilizing CNT from a dispersed form. Such membranes are robust, thermally stable, and possess high selectivity. The goal here is to immobilize CNTs such that their surfaces are free to interact directly with the solute. The membrane produced by this method has shown dramatic enhancements in flux and selectivity in various applications, such as sea water desalination (8,9), membrane extraction (10), water purification by the removal of volatile organics from water (11) and for micro scale membrane extraction for the analysis of water pollutants (12-14).

In 2016, large format commercial scale CNT membranes were introduced for the first time. Initially these membranes were produced in a flat sheet format similar to those previously made in research laboratories, although at a much larger scale. In 2017, the company announced the development of a hollow fiber membrane CNT membrane, with nanotubes oriented radially perpendicular to the membrane's surface, something that had never been achieved before. [8]

In all cases, the CNTs serve as unique pores that enhance mass transport across the membrane, selecting based on size or chemical affinity. For example, in the case of desalination the CNTs enhance the transport for water while blocking or reducing the transmission of salts, based on the size of hydrated salt ions. In the case of the removal of organics such as in water purification, pervaporation and extraction, CNT membranes preferentially permeate the organics, allowing for separations that had previously only been possible using methods like distillation. One example of organic / water separations is the separation of ethanol from water, an application in which CNT membranes show nearly ideal selectivity for the transport of ethanol. [9] [10]

Nanopore measurement in track etched membrane

Since the discovery of track-etched technology in the late 1960s, filter membranes with needed diameter have found potential use in various fields including food safety, environmental pollution, biology, medicine, fuel cell, and chemistry. These track-etched membranes are typically made in polymer membrane through track-etching procedure, during which the polymer membrane is first irradiated by heavy ion beam to form tracks and then cylindrical pores or asymmetric pores are created along the track after wet etching.

As important as fabrication of the filter membranes is the characterization and measurement of the pores in the membrane. Until now, a few of methods have been developed, which can be classified into the following categories according to the physical mechanisms they exploited: Imaging methods such as scanning electron microscopy (SEM),transmission electron microscopy (TEM), atomic force microscopy (AFM); fluid transports such as bubble point and gas transport; fluid adsorptions such as nitrogen adsorption/desorption (BEH), mercury porosimetry, liquid–vapor equilibrium (BJH), gas–liquid equilibrium (permoporometry) and liquid–solid equilibrium (thermoporometry); electronic conductance; ultrasonic spectroscopy;19 Molecular Transport.

More recently, the use of light transmission technique [11] as a method for nanopore size measurement has been proposed.

See also

Related Research Articles

<span class="mw-page-title-main">Carbon nanotube</span> Allotropes of carbon with a cylindrical nanostructure

A carbon nanotube (CNT) is a tube made of carbon with diameters typically measured in nanometers.

<span class="mw-page-title-main">Capillary</span> Smallest type of blood vessel

A capillary is a small blood vessel from 5 to 10 micrometres (μm) in diameter. Capillaries are composed of only the tunica intima, consisting of a thin wall of simple squamous endothelial cells. They are the smallest blood vessels in the body: they convey blood between the arterioles and venules. These microvessels are the site of exchange of many substances with the interstitial fluid surrounding them. Substances which cross capillaries include water, oxygen, carbon dioxide, urea, glucose, uric acid, lactic acid and creatinine. Lymph capillaries connect with larger lymph vessels to drain lymphatic fluid collected in the microcirculation.

Pervaporation is a processing method for the separation of mixtures of liquids by partial vaporization through a non-porous or porous membrane.

Ultrafiltration (UF) is a variety of membrane filtration in which forces such as pressure or concentration gradients lead to a separation through a semipermeable membrane. Suspended solids and solutes of high molecular weight are retained in the so-called retentate, while water and low molecular weight solutes pass through the membrane in the permeate (filtrate). This separation process is used in industry and research for purifying and concentrating macromolecular (103–106 Da) solutions, especially protein solutions.

<span class="mw-page-title-main">Nanoporous materials</span>

{{ }}

<span class="mw-page-title-main">Potential applications of carbon nanotubes</span>

Carbon nanotubes (CNTs) are cylinders of one or more layers of graphene (lattice). Diameters of single-walled carbon nanotubes (SWNTs) and multi-walled carbon nanotubes (MWNTs) are typically 0.8 to 2 nm and 5 to 20 nm, respectively, although MWNT diameters can exceed 100 nm. CNT lengths range from less than 100 nm to 0.5 m.

Nanofiltration is a membrane filtration process used most often to soften and disinfect water.

<span class="mw-page-title-main">Nanofluidics</span>

Nanofluidics is the study of the behavior, manipulation, and control of fluids that are confined to structures of nanometer characteristic dimensions. Fluids confined in these structures exhibit physical behaviors not observed in larger structures, such as those of micrometer dimensions and above, because the characteristic physical scaling lengths of the fluid, very closely coincide with the dimensions of the nanostructure itself.

Organic photovoltaic devices (OPVs) are fabricated from thin films of organic semiconductors, such as polymers and small-molecule compounds, and are typically on the order of 100 nm thick. Because polymer based OPVs can be made using a coating process such as spin coating or inkjet printing, they are an attractive option for inexpensively covering large areas as well as flexible plastic surfaces. A promising low cost alternative to conventional solar cells made of crystalline silicon, there is a large amount of research being dedicated throughout industry and academia towards developing OPVs and increasing their power conversion efficiency.

Reverse osmosis (RO) is a water purification process that uses a partially permeable membrane to separate ions, unwanted molecules and larger particles from drinking water. In reverse osmosis, an applied pressure is used to overcome osmotic pressure, a colligative property that is driven by chemical potential differences of the solvent, a thermodynamic parameter. Reverse osmosis can remove many types of dissolved and suspended chemical species as well as biological ones (principally bacteria) from water, and is used in both industrial processes and the production of potable water. The result is that the solute is retained on the pressurized side of the membrane and the pure solvent is allowed to pass to the other side. To be "selective", this membrane should not allow large molecules or ions through the pores (holes), but should allow smaller components of the solution (such as solvent molecules, e.g., water, H2O) to pass freely.

Carbon nanotubes (CNTs) are very prevalent in today's world of medical research and are being highly researched in the fields of efficient drug delivery and biosensing methods for disease treatment and health monitoring. Carbon nanotube technology has shown to have the potential to alter drug delivery and biosensing methods for the better, and thus, carbon nanotubes have recently garnered interest in the field of medicine.

<span class="mw-page-title-main">Capacitive deionization</span>

Capacitive deionization (CDI) is a technology to deionize water by applying an electrical potential difference over two electrodes, which are often made of porous carbon. In other words, CDI is an electro-sorption method using a combination of a sorption media and an electrical field to separate ions and charged particles. Anions, ions with a negative charge, are removed from the water and are stored in the positively polarized electrode. Likewise, cations are stored in the cathode, which is the negatively polarized electrode.

<span class="mw-page-title-main">Membrane</span> Thin, film-like structure separating two fluids, acting as a selective barrier

A membrane is a selective barrier; it allows some things to pass through but stops others. Such things may be molecules, ions, or other small particles. Membranes can be generally classified into synthetic membranes and biological membranes. Biological membranes include cell membranes ; nuclear membranes, which cover a cell nucleus; and tissue membranes, such as mucosae and serosae. Synthetic membranes are made by humans for use in laboratories and industry.

Membrane technology encompasses the scientific processes used in the construction and application of membranes. Membranes are used to facilitate the transport or rejection of substances between mediums, and the mechanical separation of gas and liquid streams. In the simplest case, filtration is achieved when the pores of the membrane are smaller than the diameter of the undesired substance, such as a harmful microorganism. Membrane technology is commonly used in industries such as water treatment, chemical and metal processing, pharmaceuticals, biotechnology, the food industry, as well as the removal of environmental pollutants.

<span class="mw-page-title-main">Single-walled carbon nanohorn</span>

Single-walled carbon nanohorn is the name given by Sumio Iijima and colleagues in 1999 to horn-shaped sheath aggregate of graphene sheets. Very similar structures had been observed in 1994 by Peter J.F. Harris, Edman Tsang, John Claridge and Malcolm Green. Ever since the discovery of the fullerene, the family of carbon nanostructures has been steadily expanded. Included in this family are single-walled and multi-walled carbon nanotubes, carbon onions and cones and, most recently, SWNHs. These SWNHs with about 40–50 nm in tubule length and about 2–3 nm in diameter are derived from SWNTs and ended by a five-pentagon conical cap with a cone opening angle of ~20o. Moreover, thousands of SWNHs associate with each other to form the ‘dahlia-like' and ‘bud-like’ structured aggregates which have an average diameter of about 80–100 nm. The former consists of tubules and graphene sheets protruding from its surface like petals of a dahlia, while the latter is composed of tubules developing inside the particle itself. Their unique structures with high surface area and microporosity make SWNHs become a promising material for gas adsorption, biosensing, drug delivery, gas storage and catalyst support for fuel cell. Single-walled carbon nanohorns are an example of the family of carbon nanocones.

Water shortages have become an increasingly pressing concern recently and with recent predictions of a high probability of the current drought turning into a megadrought occurring in the western United States, technologies involving water treatment and processing need to improve. Carbon nanotubes (CNT) have been the subject of extensive studies because they demonstrate a range of unique properties that existing technologies lack. For example, carbon nanotube membranes can demonstrate higher water flux with lower energy than current membranes. These membranes can also filter out particles that are too small for conventional systems which can lead to better water purification techniques and less waste. The largest obstacle facing CNT is processing as it is difficult to produce them in the large quantities that most of these technologies will require.

<span class="mw-page-title-main">Synthesis of carbon nanotubes</span> Class of manufacturing

Techniques have been developed to produce carbon nanotubes in sizable quantities, including arc discharge, laser ablation, high-pressure carbon monoxide disproportionation, and chemical vapor deposition (CVD). Most of these processes take place in a vacuum or with process gases. CVD growth of CNTs can occur in vacuum or at atmospheric pressure. Large quantities of nanotubes can be synthesized by these methods; advances in catalysis and continuous growth are making CNTs more commercially viable.

Vertically aligned carbon nanotube arrays (VANTAs) are a unique microstructure consisting of carbon nanotubes oriented with their longitudinal axis perpendicular to a substrate surface. These VANTAs effectively preserve and often accentuate the unique anisotropic properties of individual carbon nanotubes and possess a morphology that may be precisely controlled. VANTAs are consequently widely useful in a range of current and potential device applications.

There are many water purifiers available in the market which use different techniques like boiling, filtration, distillation, chlorination, sedimentation and oxidation. Currently nanotechnology plays a vital role in water purification techniques. Nanotechnology is the process of manipulating atoms on a nanoscale. In nanotechnology, nano membranes are used with the purpose of softening the water and removal of contaminants such as physical, biological and chemical contaminants. There are variety of techniques in nanotechnology which uses nano particles for providing safe drinking water with a high level of effectiveness. Some techniques have become commercialized.

Olgica Bakajin is a scientist working at Porifera, Inc.

References

  1. ↑ Hummer, G.; Rasaiah, J. C.; Noworyta, J. P. (2001). "Water conduction through the hydrophobic channel of a carbon nanotube". Nature. 414 (6860): 188–90. Bibcode:2001Natur.414..188H. doi:10.1038/35102535. PMID   11700553.
  2. ↑ Sholl, D. S.; Johnson, JK (2006). "Making High-Flux Membranes with Carbon Nanotubes". Science. 312 (5776): 1003–4. doi:10.1126/science.1127261. PMID   16709770.
  3. ↑ Li Sun & Richard M. Crooks (2000). "Single Carbon Nanotube Membranes: A Well-Defined Model for Studying Mass Transport through Nanoporous Materials". J. Am. Chem. Soc. 122 (49): 12340–12345. doi:10.1021/ja002429w.
  4. ↑ Hinds, B. J.; Chopra, N; Rantell, T; Andrews, R; Gavalas, V; Bachas, LG (2004). "Aligned multiwalled carbon nanotube membranes". Science. 303 (5654): 62–5. Bibcode:2004Sci...303...62H. doi:10.1126/science.1092048. PMID   14645855.
  5. 1 2 Majumder, Mainak; Chopra, Nitin; Andrews, Rodney; Hinds, Bruce J. (2005). "Nanoscale hydrodynamics: Enhanced flow in carbon nanotubes". Nature. 438 (7064): 44. Bibcode:2005Natur.438...44M. doi: 10.1038/438044a . PMID   16267546.
  6. 1 2 Holt, J. K.; Park, HG; Wang, Y; Stadermann, M; Artyukhin, AB; Grigoropoulos, CP; Noy, A; Bakajin, O (2006). "Fast Mass Transport Through Sub-2-Nanometer Carbon Nanotubes". Science. 312 (5776): 1034–7. Bibcode:2006Sci...312.1034H. doi:10.1126/science.1126298. PMID   16709781.
  7. ↑ Wang, Zuankai; Ci, Lijie; Chen, Li; Nayak, Saroj; Ajayan, Pulickel M.; Koratkar, Nikhil (2007). "Polarity-Dependent Electrochemically Controlled Transport of Water through Carbon Nanotube Membranes". Nano Lett. 7 (3): 697–702. Bibcode:2007NanoL...7..697W. doi:10.1021/nl062853g. PMID   17295548.
  8. ↑ "(363d) Radially Aligned Carbon Nanotube Hollow Fiber Membranes | AIChE". www.aiche.org. Retrieved 2020-01-23.
  9. ↑ Gravelle, Simon; Yoshida, Hiroaki; Joly, Laurent; Ybert, Christophe; Bocquet, Lydéric (2016-09-27). "Carbon membranes for efficient water-ethanol separation" (PDF). The Journal of Chemical Physics. 145 (12): 124708. doi:10.1063/1.4963098. ISSN   0021-9606. PMID   27782663.
  10. ↑ Winarto; Takaiwa, Daisuke; Yamamoto, Eiji; Yasuoka, Kenji (2016). "Separation of water–ethanol solutions with carbon nanotubes and electric fields". Physical Chemistry Chemical Physics. 18 (48): 33310–33319. doi: 10.1039/C6CP06731J . PMID   27897278.
  11. ↑ Li Yang; Qingfeng Zhai; Guijuan Li; Hong Jiang; Lei Han; Jiahai Wang; Erkang Wang (October 2013). "Light Transmission Technique for Pore Size Measurement in Track-Etched Membranes". Chemical Communications. 49 (97): 11415–7. doi:10.1039/c3cc45841e. PMID   24169442.


8. : "Carbon Nanotube Enhanced Membrane Distillation of Simultaneous Generation of Pure Water and Concentrating Pharmaceutical Waste". Ken Gethard, Ornthida Sae-Khow, Somenath Mitra. 90, 239-245, . Separation and Purification Technology. 2012

9.:::"Water Desalination Using Carbon Nanotube Enhanced Membrane Distillation". Ken Gethard, Ornthida Sae-Khow, Somenath Mitra. ACS Applied Materials and Interfaces. 2011, 3, 110–114.

10.:::"Simultaneous Extraction and Concentration in Carbon Nanotube Immobilized Hollow Fiber Membranes". Ornthida Sae-Khow and Somenath Mitra. Anal. Chem. 2010, 82 (13), 5561-5567.

11.:::"Carbon Nanotube Immobilized Composite Hollow Fiber Membranes for Pervaporative Removal of Volatile Organics from water" ". Ornthida Sae-Khow and Somenath Mitra. J. Phys. Chem. C. 2010, 114,16351-16356.

12.:::"Fabrication and Characterization of Carbon Nanotubes Immobilized Porous Polymeric Membranes". Ornthida Sae-Khow and Somenath Mitra. J. Mater. Chem., 2009, 19 (22), 3713-3718.

13.:: "Carbon Nanotube Mediated Microscale Membrane Extraction". K. Hylton, Y. Chen, S. Mitra, J. Chromatogr. A., 2008, 1211, 43-48.

14.:: "Carbon Nanotube Immobilized Polar Membranes for Enhanced Extraction of Polar Analytes". Madhuleena. Bhadra, Somenath. Mitra. Analyst. 2012, 137, 4464-4468.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.