Rumble (noise)

Last updated

A rumble is a continuous deep, resonant sound, such as the sound made by heavy vehicles or thunder. [1] In the context of audio reproduction rumble refers to a low frequency sound from the bearings inside a turntable. This is most noticeable in low quality turntables with ball bearings. Higher quality turntables use slide bearings, minimizing rumble.

Contents

Some phono pre-amplifiers implement a rumble filter, in an attempt to remove the noise. A heavier platter can also help dampen this.

Rumble measurement is carried out on turntables (for vinyl recordings) which tend to generate very low frequency noise originating from the centre bearing and from drive pulleys or belts, as well as from irregularities in the record disc itself.

It can be heard as low-frequency noise and becomes a serious problem when playing records on audio systems with a good low-frequency response. Even when not audible, rumble can cause intermodulation, modulating of the amplitude of other frequencies. The ‘unweighted’ response curve is intended for use in assessing the level of inaudible rumble with such intermodulation in mind.

Turntable design

IEC 98 (1984) Rumble Weighting curves.svg

One way to reduce rumble is to make the turntable very heavy, so that it acts as mechanical damper or low-pass filter, but even with the best turntables a lot of rumble tends to be generated by warped records or pressing irregularities sometimes visible as ‘bobbles’ in the surface. An important factor affecting rumble is low-frequency resonance resulting from pickup arm mass bouncing against stylus compliance. This resonance is usually in the 10–30 Hz region, and will increase rumble as well as reducing tracking ability if not well-damped. Some pickup arms incorporate viscous damping aimed at eliminating such resonance.

Rumble filters

Because these effects generate a mostly vertical component at the stylus, which corresponds to a difference signal in stereo reproduction, the incorporation of a high-pass filter operating only on the channel difference can be very effective in reducing rumble without loss of bass. Such a filter merges the two channels to mono at very low frequencies, which is not generally considered to have any effect on stereo perception, though it can change the sound balance (often for the better) by altering the way in which resonant room modes are stimulated (reducing corner to corner stimulation). The original circuit was designed in 1978 by Jeff Macaulay and featured as a circuit idea in Wireless World. Most so-called rumble filters work by simply rolling off the low-frequency response, which is detrimental to sound quality.

Though several standards exist that define how rumble should be measured, they all have a common basis, and use the weighting curves shown here. DIN 45539 (1971) and IEC98-1964 both cover rumble measurement. BS4852: Part 1 (1972) is specific in requiring that a slow rectifier be used, which shall reach 99% of its steady indication in 5s +-0.5s with not more than 10% overshoot.

Related Research Articles

In signal processing, distortion is the alteration of the original shape of a signal. In communications and electronics it means the alteration of the waveform of an information-bearing signal, such as an audio signal representing sound or a video signal representing images, in an electronic device or communication channel.

<span class="mw-page-title-main">Microphone</span> Device that converts sound into an electrical signal

A microphone, colloquially called a mic, is a transducer that converts sound into an electrical signal. Microphones are used in many applications such as telephones, hearing aids, public address systems for concert halls and public events, motion picture production, live and recorded audio engineering, sound recording, two-way radios, megaphones, and radio and television broadcasting. They are also used in computers for recording voice, speech recognition, VoIP, and for other purposes such as ultrasonic sensors or knock sensors.

Sound can be recorded and stored and played using either digital or analog techniques. Both techniques introduce errors and distortions in the sound, and these methods can be systematically compared. Musicians and listeners have argued over the superiority of digital versus analog sound recordings. Arguments for analog systems include the absence of fundamental error mechanisms which are present in digital audio systems, including aliasing and associated anti-aliasing filter implementation, jitter and quantization noise. Advocates of digital point to the high levels of performance possible with digital audio, including excellent linearity in the audible band and low levels of noise and distortion.

<span class="mw-page-title-main">Audio system measurements</span> Means of quantifying system performance

Audio system measurements are a means of quantifying system performance. These measurements are made for several purposes. Designers take measurements so that they can specify the performance of a piece of equipment. Maintenance engineers make them to ensure equipment is still working to specification, or to ensure that the cumulative defects of an audio path are within limits considered acceptable. Audio system measurements often accommodate psychoacoustic principles to measure the system in a way that relates to human hearing.

<span class="mw-page-title-main">Laser turntable</span> Turntable that plays records using laser beams

A laser turntable is a phonograph that plays standard LP records using laser beams as the pickup instead of using a stylus as in conventional turntables. Although these turntables use laser pickups, the same as Compact Disc players, the signal remains in the analog realm and is never digitized.

<span class="mw-page-title-main">Damping factor</span>

In an audio system, the damping factor gives the ratio of the rated impedance of the loudspeaker to the source impedance of the power amplifier. Only the magnitude of the loudspeaker impedance is used, and the power amplifier output impedance is assumed to be totally resistive.

<span class="mw-page-title-main">Equal-loudness contour</span> Frequency characteristics of hearing and perceived volume

An equal-loudness contour is a measure of sound pressure level, over the frequency spectrum, for which a listener perceives a constant loudness when presented with pure steady tones. The unit of measurement for loudness levels is the phon and is arrived at by reference to equal-loudness contours. By definition, two sine waves of differing frequencies are said to have equal-loudness level measured in phons if they are perceived as equally loud by the average young person without significant hearing impairment.

<span class="mw-page-title-main">Pickup (music technology)</span> Transducer that senses vibration of musical instruments

A pickup is a transducer that captures or senses mechanical vibrations produced by musical instruments, particularly stringed instruments such as the electric guitar, and converts these to an electrical signal that is amplified using an instrument amplifier to produce musical sounds through a loudspeaker in a speaker enclosure. The signal from a pickup can also be recorded directly.

<span class="mw-page-title-main">Bass reflex</span> Type of loudspeaker enclosure with improved bass performance

A bass reflex system is a type of loudspeaker enclosure that uses a port (hole) or vent cut into the cabinet and a section of tubing or pipe affixed to the port. This port enables the sound from the rear side of the diaphragm to increase the efficiency of the system at low frequencies as compared to a typical sealed- or closed-box loudspeaker or an infinite baffle mounting.

<span class="mw-page-title-main">Weighting</span>

The process of weighting involves emphasizing the contribution of particular aspects of a phenomenon over others to an outcome or result; thereby highlighting those aspects in comparison to others in the analysis. That is, rather than each variable in the data set contributing equally to the final result, some of the data is adjusted to make a greater contribution than others. This is analogous to the practice of adding (extra) weight to one side of a pair of scales in order to favour either the buyer or seller.

Measurement of wow and flutter is carried out on audio tape machines, cassette recorders and players, and other analog recording and reproduction devices with rotary components This measurement quantifies the amount of 'frequency wobble' present in subjectively valid terms. Turntables tend to suffer mainly slow wow. In digital systems, which are locked to crystal oscillators, variations in clock timing are referred to as wander or jitter, depending on speed.

<span class="mw-page-title-main">RIAA equalization</span> Specification for the recording and playback of phonograph records

RIAA equalization is a specification for the recording and playback of phonograph records, established by the Recording Industry Association of America (RIAA). The purposes of the equalization are to permit greater recording times, to improve sound quality, and to reduce the groove damage that would otherwise arise during playback.

Audio noise measurement is a process carried out to assess the quality of audio equipment, such as the kind used in recording studios, broadcast engineering, and in-home high fidelity.

Room modes are the collection of resonances that exist in a room when the room is excited by an acoustic source such as a loudspeaker. Most rooms have their fundamental resonances in the 20 Hz to 200 Hz region, each frequency being related to one or more of the room's dimensions or a divisor thereof. These resonances affect the low-frequency low-mid-frequency response of a sound system in the room and are one of the biggest obstacles to accurate sound reproduction.

<span class="mw-page-title-main">Loudspeaker measurement</span> Quantifying the behaviour of loudspeakers

Loudspeaker measurement is the practice of determining the behaviour of loudspeakers by measuring various aspects of performance. This measurement is especially important because loudspeakers, being transducers, have a higher level of distortion than other audio system components used in playback or sound reinforcement.

Record restoration, a particular kind of audio restoration, is the process of converting the analog signal stored on gramophone records into digital audio files that can then be edited with computer software and eventually stored on a hard-drive, recorded to digital tape, or burned to a CD or DVD. The process may be divided into several separate steps performed in the following order:

  1. Cleaning the record, to prevent unwanted audio artifacts from being introduced in the capture that will necessitate correction in the digital domain, and to prevent unnecessary wear and damage to the stylus used in playback.
  2. Transcription of the record to another format on another medium ;
  3. Processing the raw sound file with software in order to remove transient noise resulting from record surface damage ;
  4. Using software to adjust the volume and equalization;
  5. Processing the audio with digital and analogue techniques to reduce surface/wideband noise;
  6. Saving the file in the desired format.
<span class="mw-page-title-main">A-weighting</span> Frequency response curves used in sound pressure level measurement

A-weighting is the most commonly used of a family of curves defined in the International standard IEC 61672:2003 and various national standards relating to the measurement of sound pressure level. A-weighting is applied to instrument-measured sound levels in an effort to account for the relative loudness perceived by the human ear, as the ear is less sensitive to low audio frequencies. It is employed by arithmetically adding a table of values, listed by octave or third-octave bands, to the measured sound pressure levels in dB. The resulting octave band measurements are usually added to provide a single A-weighted value describing the sound; the units are written as dB(A). Other weighting sets of values – B, C, D and now Z – are discussed below.

<span class="mw-page-title-main">Moving iron speaker</span>

The moving iron speaker was the earliest type of electric loudspeaker. They are still used today in some miniature speakers where small size and low cost are more important than sound quality. A moving iron speaker consists of a ferrous-metal diaphragm or reed, a permanent magnet and a coil of insulated wire. The coil is wound around the permanent magnet to form a solenoid. When an audio signal is applied to the coil, the strength of the magnetic field varies, and the springy diaphragm or reed moves in response to the varying force on it. The moving iron loudspeaker Bell telephone receiver was of this form. Large units had a paper cone attached to a ferrous metal reed.

<span class="mw-page-title-main">Equalization (audio)</span> Changing the balance of frequency components in an audio signal

Equalization, or simply EQ, in sound recording and reproduction is the process of adjusting the volume of different frequency bands within an audio signal. The circuit or equipment used to achieve this is called an equalizer.

<span class="mw-page-title-main">Audio analyzer</span> Test and measurement instrument

An audio analyzer is a test and measurement instrument used to objectively quantify the audio performance of electronic and electro-acoustical devices. Audio quality metrics cover a wide variety of parameters, including level, gain, noise, harmonic and intermodulation distortion, frequency response, relative phase of signals, interchannel crosstalk, and more. In addition, many manufacturers have requirements for behavior and connectivity of audio devices that require specific tests and confirmations.

References

  1. Anon. "Rumble". Oxford Dictionaries. Oxford University Press. Archived from the original on July 22, 2012. Retrieved 6 May 2014.

See also