Salisbury Cathedral clock

Last updated

Salisbury Cathedral clock, restored Salisbury Cathedral, medieval clock.JPG
Salisbury Cathedral clock, restored

The Salisbury Cathedral clock is a large iron-framed tower clock without a dial, in Salisbury Cathedral, England. Thought to date from about 1386, it is a well-preserved example of the earliest type of mechanical clock, called verge and foliot clocks, and is said to be the oldest working clock in the world, [1] although similar claims are made for other clocks. Previously in a bell-tower which was demolished in 1790, the clock was restored to working condition in 1956 and is on display in the North nave aisle of the cathedral, close to the West front.

Contents

History

The clock was re-discovered in 1928, set aside in the cathedral tower. At that time it had a pendulum, which appeared to have been installed at a later date, replacing a verge and foliot. The clock was restored in 1956, and a reproduction verge and foliot were installed. There were no drawings or documents available, and it is possible that the original foliot and verge escapement did not look exactly like the one now installed in the clock.

The striking train of the clock is believed to be original.

Like many of these more practical devices, its main purpose was to strike a bell at precise times. It probably did not have a dial. The wheels and gears are mounted in a four-post wrought iron frame. The framework is held together with metal wedged tenons, rather than with nuts and bolts (which had not been invented).

As found, the escapement was a pendulum which must have been a replacement, as it is too early for clocks of this age, which would have had verge and foliot. The power was supplied by two large stone weights. As the weights descend, ropes unwind from the wooden barrels. One barrel drives the going train which is regulated by the escapement; the other drives the striking train, the speed of which is regulated by the fly (air brake).

Before the weights reach the floor, they have to be wound back up again, a task that explains the presence of two large wheels shaped like steering wheels at either end of the clock.

The clock is now a "single strike" clock that strikes only on the hour. It makes one strike per hour of the day (e.g. one strike at noon). The left half of the clock (as in the photograph above), is the striking train; the right half is the going train. When it was built, it may have simply struck bells for the masses, of which there were up to four.

At the end of the 17th century, the Salisbury clock, like many others, was modified from verge and foliot to pendulum and anchor operation. This usually made clocks much more accurate, even though trials in the early 1990s by Michael Maltin showed that the clock was running to within two minutes a day if the rope on the barrel was kept in a single layer. As soon as there are two layers, more torque is applied to the barrel by the weight and the clock goes faster. As a single layer of winding is enough to keep the clock going for 12 hours, it could have been kept exact to within two minutes per day if it had been wound twice per day.

In 1790, the old bell tower 'on the ditch of the close of the canons of the said church' mentioned in the deed of 1386 which had housed the clock was demolished, so the clock was moved to the Cathedral's central tower. In 1884, a new clock was installed and the old one was left to the side.

"Oldest working clock" claim

Others claimed to be the world's oldest working clock are in the cathedral of Beauvais in France (said to date from 1305, and entirely preserved, in its architecured frame), [2] the clock tower of Chioggia in Italy, and the clock of the Comayagua Cathedral, in Honduras. (Said to be built in Spain by the Moors during the 12th century, although records of it are lost). [3] The oldest clock in the world with a proofed engraved date (1463) is the Backhaus clock  [ de ] in Forchtenberg, Germany.

The clock is one of a group of 14th to 16th century clocks to be found in the West of England at Wells, Exeter, Castle Combe, Ottery St Mary, and Wimborne Minster. An attempt to date this clock to around 1386 was made by T.R. Robinson. His estimated date has been supported by others.

Mechanical clocks began to flourish in Europe in the 14th century. Other clocks from that century, such as those at Rouen (Gros Horloge), Paris (Heinrich von Wick clock) or Dijon (the clock taken by Philip the Bold from Courtrai in 1382), have either been lost, destroyed, or substantially modified. The Wells Cathedral clock might have been made by the same craftsmen as the Salisbury clock, but is usually dated to around 1392, and is now in the Science Museum in London, where it continues to operate.

There are some doubts that the clock displayed in Salisbury Cathedral is actually the clock mentioned in 1386, as the construction is quite advanced and more comparable to clocks made in the 16th and 17th century than those made in the 14th century. The question if this is the 1386 clock is quite important as the Wells Cathedral clock was previously dated in the 16th century, but then dated 1392 after the discovery of the Salisbury clock in 1928. Dating mistakes for old turret clocks are not uncommon. The Dover Castle clock was initially dated in the 14th century, only to be later revised to around 1600.

In 1993, Christopher McKay organised a symposium with the Antiquarian Horological Society to determine if the clock could be dated to 1386. The majority of participants voted for it to be the original, but roughly 1/3 of participants voted the clock to be of a much later date.

Revival

The clock was re-discovered in the tower in 1928 by T.R. Robinson, an horological enthusiast who went up the clock tower to see the new clock (installed in 1884). The presence of the old clock was known to many, but nobody attributed much importance to it. It was only T.R. Robinson who believed that it was the clock mentioned in 1386. From photos taken in 1928, it looked to be fairly complete. Eventually its historic importance was realised. It was first put on display in the Cathedral's North transept. Then, in 1956, the clock was restored towards its presumed original condition and started working again. The pendulum and recoil escapement were replaced by a new verge and foliot escapement, thus restoring the clock to something like its original design.

Today, the escapement operates, but the striking mechanism is normally prevented from running by a clamp, which may be removed for demonstration purposes.

1956 restoration

Messrs. John Smith & Sons of Derby received the clock in February 1956. It was taken apart for the transport. They reassembled the clock in their workshop and compared it to existing clocks in the Science Museum before deciding how to restore it.

The help of Rolls-Royce was enlisted to have X-ray photographs of two of the wheel arbors taken. This confirmed that the two arbors of the going train had been lengthened when the clock had been converted to pendulum operation. Subsequent investigations revealed that the clock had actually been converted twice, as remains of an earlier pendulum escapement were discovered.

The clock is now displayed in the North nave aisle of the cathedral, close to the West front. [4]

TrainPartPrevious work1956 Restoration
going traingreat wheeldisc with two pins attached to great wheel as it only turned once every two hours due to conversion to pendulumafter removing the disc, the original hole for the pin was discovered and a new pin was fitted
going trainescape wheelreplaced with anchor escape wheelnew escape wheel forged, teeth marked out by hand, riveted onto existing second wheel
going trainwinding barrelnew wooden winding barrel fitted
going trainfoliot support bracketnew foliot support bracket forged and fitted
going trainfoliotnew foliot forged and fitted
striking trainhoop wheelflange of hoop wheel reversedflange of hoop wheel replaced correctly
going trainturning direction, strike releasestrike release moved to front of frame, rotation of going train reversed to clock-wise to fit clock dial (1613)strike release moved to back of frame, rotation of going train reversed to anti clock-wise as it was originally

Technical details

Frame

The frame height is 1.24m, the width 1.29m, and the depth 1.06m.

Going train

The going train of the clock Salisbury going train 01.JPG
The going train of the clock

Great wheel to verge escape wheel: 100 to 10, verge escape wheel 45 teeth.

The Great wheel turns once in 3600 seconds (1 hour), so the verge escape wheel turns once in 360 seconds. One full foliot swing thus takes 8 seconds, or 4 seconds per half swing.

Seen from the going train side, the great wheel with the winding barrel turns anti-clockwise, and the escapement wheel turns clockwise.

Striking train

The striking train of the clock Salisbury striking train.jpg
The striking train of the clock

Great wheel to fly: 64 teeth driving an 8 pin birdcage; second (hoop) wheel 64 teeth driving an 8 leaf pinion on the fly. So each turn of the great wheel makes the fly turn 64 times, or 8 turns of the fly per strike of the clock (as the great wheel has 8 striking pins).

Great wheel to count wheel: 8 tooth pinion to internal 78 teeth on count wheel, with 8 striking pins on the great wheel. This directly corresponds with the 78 strikes the clock will make in 12 hours (1 + 2 + 3 + 4 + 5 + 6 + 7 + 8 + 9 + 10 + 11 + 12 = 78). The count wheel turns once every 12 hours, so the great wheel turns 9.75 times, operating the strike lever thus 9.75 × 8 = 78 times.

Seen from the striking train side, the great wheel with the winding barrel turns clockwise, the hoop wheel anti-clockwise, the count wheel clockwise, and the fly clockwise.

The count wheel only appears to have 11 notches, but the clock strikes 12 times each complete turn. This is because the first strike (when the clock strikes one) is executed whilst the lever is still within the first, wider, notch. The locking piece is lifted out of the hoop of the hoop wheel, which then turns once, which leads to the great wheel turning 1/8 and striking once. Then the locking piece falls back into the hoop wheel. The fly will continue to turn until it stops gently on his own as it has a ratchet mechanism, which protects the bird cage on the fly arbor.

Related Research Articles

<span class="mw-page-title-main">Pendulum clock</span> Clock regulated by a pendulum

A pendulum clock is a clock that uses a pendulum, a swinging weight, as its timekeeping element. The advantage of a pendulum for timekeeping is that it is an approximate harmonic oscillator: It swings back and forth in a precise time interval dependent on its length, and resists swinging at other rates. From its invention in 1656 by Christiaan Huygens, inspired by Galileo Galilei, until the 1930s, the pendulum clock was the world's most precise timekeeper, accounting for its widespread use. Throughout the 18th and 19th centuries, pendulum clocks in homes, factories, offices, and railroad stations served as primary time standards for scheduling daily life, work shifts, and public transportation. Their greater accuracy allowed for the faster pace of life which was necessary for the Industrial Revolution. The home pendulum clock was replaced by less-expensive synchronous electric clocks in the 1930s and '40s. Pendulum clocks are now kept mostly for their decorative and antique value.

<span class="mw-page-title-main">Grasshopper escapement</span> Low friction clock escapement

The grasshopper escapement is a low-friction escapement for pendulum clocks invented by British clockmaker John Harrison around 1722. An escapement, part of every mechanical clock, is the mechanism that gives the clock's pendulum periodic pushes to keep it swinging, and each swing releases the clock's gears to move forward by a fixed amount, thus moving the hands forward at a steady rate. The grasshopper escapement was used in a few regulator clocks built during Harrison's time, and a few others over the years, but has never seen wide use. The term "grasshopper" in this connection, apparently from the kicking action of the pallets, first appears in the Horological Journal in the late 19th century.

<span class="mw-page-title-main">Escapement</span> Mechanism for regulating the speed of clocks

An escapement is a mechanical linkage in mechanical watches and clocks that gives impulses to the timekeeping element and periodically releases the gear train to move forward, advancing the clock's hands. The impulse action transfers energy to the clock's timekeeping element to replace the energy lost to friction during its cycle and keep the timekeeper oscillating. The escapement is driven by force from a coiled spring or a suspended weight, transmitted through the timepiece's gear train. Each swing of the pendulum or balance wheel releases a tooth of the escapement's escape wheel, allowing the clock's gear train to advance or "escape" by a fixed amount. This regular periodic advancement moves the clock's hands forward at a steady rate. At the same time, the tooth gives the timekeeping element a push, before another tooth catches on the escapement's pallet, returning the escapement to its "locked" state. The sudden stopping of the escapement's tooth is what generates the characteristic "ticking" sound heard in operating mechanical clocks and watches.

<span class="mw-page-title-main">Movement (clockwork)</span> Mechanism of a watch or clock

In horology, a movement, also known as a caliber or calibre, is the mechanism of a watch or timepiece, as opposed to the case, which encloses and protects the movement, and the face, which displays the time. The term originated with mechanical timepieces, whose clockwork movements are made of many moving parts. The movement of a digital watch is more commonly known as a module.

<span class="mw-page-title-main">Anchor escapement</span> Type of mechanism used in pendulum clocks

In horology, the anchor escapement is a type of escapement used in pendulum clocks. The escapement is a mechanism in a mechanical clock that maintains the swing of the pendulum by giving it a small push each swing, and allows the clock's wheels to advance a fixed amount with each swing, moving the clock's hands forward. The anchor escapement was so named because one of its principal parts is shaped vaguely like a ship's anchor.

<span class="mw-page-title-main">Verge escapement</span> Early clock mechanism

The vergeescapement is the earliest known type of mechanical escapement, the mechanism in a mechanical clock that controls its rate by allowing the gear train to advance at regular intervals or 'ticks'. Verge escapements were used from the late 13th century until the mid 19th century in clocks and pocketwatches. The name verge comes from the Latin virga, meaning stick or rod.

<span class="mw-page-title-main">Striking clock</span> Clock that sounds the time with a bell or gong

A striking clock is a clock that sounds the hours audibly on a bell, gong, or other audible device. In 12-hour striking, used most commonly in striking clocks today, the clock strikes once at 1:00 am, twice at 2:00 am, continuing in this way up to twelve times at 12:00 mid-day, then starts again, striking once at 1:00 pm, twice at 2:00 pm, and the pattern continues up to twelve times at 12:00 midnight.

<span class="mw-page-title-main">Fusee (horology)</span> Mainspring force equalizing pulley in timepieces

A fusee is a cone-shaped pulley with a helical groove around it, wound with a cord or chain attached to the mainspring barrel of antique mechanical watches and clocks. It was used from the 15th century to the early 20th century to improve timekeeping by equalizing the uneven pull of the mainspring as it ran down. Gawaine Baillie stated of the fusee, "Perhaps no problem in mechanics has ever been solved so simply and so perfectly."

<span class="mw-page-title-main">Japanese clock</span> Mechanical clock that has been made to tell traditional Japanese time

A Japanese clock is a mechanical clock that has been made to tell traditional Japanese time, a system in which daytime and nighttime are always divided into six periods whose lengths consequently change with the season. Mechanical clocks were introduced into Japan by Jesuit missionaries or Dutch merchants. These clocks were of the lantern clock design, typically made of brass or iron, and used the relatively primitive verge and foliot escapement. Tokugawa Ieyasu owned a lantern clock of European manufacture.

<span class="mw-page-title-main">St Mark's Clock</span> Clock tower in Venice, Italy

St Mark's Clock is housed in the Clock Tower on the Piazza San Marco in Venice, Italy, adjoining the Procuratie Vecchie. The first clock housed in the tower was built and installed by Gian Paolo and Gian Carlo Rainieri, father and son, between 1496 and 1499, and was one of a number of large public astronomical clocks erected throughout Europe during the 14th and 15th centuries. The clock has had an eventful horological history, and been the subject of many restorations, some controversial.

<span class="mw-page-title-main">Wells Cathedral clock</span> Clock

The Wells Cathedral clock is an astronomical clock in the north transept of Wells Cathedral, England. The clock is one of the group of famous 14th– to 16th–century astronomical clocks to be found in the West of England. The surviving mechanism, dated to between 1386 and 1392, was replaced in the 19th century, and was eventually moved to the Science Museum in London, where it continues to operate. The dial represents the geocentric view of the universe, with the Sun and Moon revolving round a central fixed Earth. It may be unique in showing a philosophical model of the pre-Copernican universe.

<span class="mw-page-title-main">Turret clock</span> Large prominently located clock used as a public amenity

A turret clock or tower clock is a clock designed to be mounted high in the wall of a building, usually in a clock tower, in public buildings such as churches, university buildings, and town halls. As a public amenity to enable the community to tell the time, it has a large face visible from far away, and often a striking mechanism which rings bells upon the hours.

Edward Martin Burgess FSA FBHI, known as Martin Burgess, was an English horologist and master clockmaker.

<span class="mw-page-title-main">History of timekeeping devices</span>

The history of timekeeping devices dates back to when ancient civilizations first observed astronomical bodies as they moved across the sky. Devices and methods for keeping time have gradually improved through a series of new inventions, starting with measuring time by continuous processes, such as the flow of liquid in water clocks, to mechanical clocks, and eventually repetitive, oscillatory processes, such as the swing of pendulums. Oscillating timekeepers are used in modern timepieces.

In horology, a wheel train is the gear train of a mechanical watch or clock. Although the term is used for other types of gear trains, the long history of mechanical timepieces has created a traditional terminology for their gear trains which is not used in other applications of gears.

<span class="mw-page-title-main">Castle Combe Clock</span> Clock in St. Andrews Church, England

The Castle Combe clock in St. Andrew's Church, Castle Combe, Wiltshire, England was probably made in the late 15th century. It is faceless and strikes a bell in the church tower.

<span class="mw-page-title-main">Cotehele clock</span> Turret clock in Cornwall, England

The Cotehele clock is situated at Cotehele House, Calstock, Cornwall. It is the earliest turret clock in the United Kingdom still working in an unaltered state and in its original position. It was probably installed between 1493 and 1521.

<span class="mw-page-title-main">William Hamilton Shortt</span> British horologist and engineer

William Hamilton Shortt (1881–1971) was a railway engineer and noted horologist, responsible for the design of the Shortt-Synchronome free pendulum clock, a widely used time standard, employed internationally in observatories in the period between the two World Wars. His deep involvement in precision timekeeping, as a colleague of Frank Hope-Jones and director of the Synchronome Company, derived from work on the safety of train travel and the accurate measurement of train speeds, following investigations into a serious train derailment of a LSWR train at Salisbury Station in 1906, when twenty-eight people died.

<span class="mw-page-title-main">The Backhaus Clock</span> Historically Significant Clock

The Backhaus Clock, also known as the Forchtenberg Tower Clock, is a historical mechanical tower clock located in Forchtenberg, Baden-Württemberg, Germany. It is notable for the year 1463 engraved on its frame in Gothic script, which marks it as the oldest dated tower clock still in operation in the world. Unlike the contentious dating of other ancient clocks, such as the one in Salisbury Cathedral, the Forchtenberg Clock's date is clearly inscribed on the clock itself, though it remains ambiguous whether this date refers to the clock's original construction or an early repair.

<span class="mw-page-title-main">Comayagua cathedral clock</span> Clock in Comayagua

The Comayagua cathedral clock, also known as the Arabic clock or the Comayagua clock, is a gear clock dated from the medieval times located in the city of Comayagua, in the Republic of Honduras. It is considered the oldest clock in the Americas and the oldest gear clock in the world still in operation since it has been working presumably for more than 900 years.

References

  1. "World's oldest clock". Salisbury Cathedral. Archived from the original on 1 November 2020. Retrieved 16 September 2018.
  2. "Beauvais medieval".
  3. "Reloj Clock Comayagua". www.comayagua.org. Archived from the original on 31 October 2018. Retrieved 31 October 2018.
  4. "What to See". Salisbury Cathedral. Retrieved 30 October 2023.

Further reading