Sound Blaster Live! is a PCI add-on sound card from Creative Technology Limited for PCs. Moving from ISA to PCI allowed the card to dispense with onboard memory, storing digital samples in the computer's main memory and then accessing them in real time over the bus. This allowed for a much wider selection of, and longer playing, samples. It also included higher quality sound output at all levels, quadrophonic output, and a new MIDI synthesizer with 64 sampled voices. The Live! was introduced on August 11, 1998[1] and variations on the design remained Creative's primary sound card line into the early 2000's.
EMU10K1 Digital Signal ProcessorEMU10K1-NDF digital sound processorSound Blaster Live!Sound Blaster Live! Value / Compaq / Intel / IBM / NEC
Sound Blaster Live! (August 1998) saw the introduction of the EMU10K1 audio processor. Manufactured in a 0.35µm 3-metal-layer CMOS process, it is a 2.44 million transistor ASIC rated at 1000 MIPS. The EMU10K1 featured hardware acceleration for DirectSound and EAX 1.0 and 2.0 (environmental audio extensions), along with a high-quality 64-voice MIDI sample-based synthesizer and an integrated FX8010DSP chip for real-time digital audio effects.[2]
A major design change from its predecessor (the EMU8000) was that the EMU10K1 used system memory, accessed over the PCI bus, for the wavetable samples, rather than using expensive on-board memory. This was possible at this point because systems were being equipped with far more RAM than previously, and PCI offered far faster and more efficient data transfer than the old ISA bus.
The integrated FX8010 was a 32-bit programmable processor with 1 kilobyte of instruction memory. It provided real-time postprocessing effects (such as reverb, flanging, or chorus). This capability let users select a pre-defined listening environment from a control-panel application (concert hall, theater, headphones, etc.) It also provided hardware-acceleration for EAX, Creative's environmental audio technology. The Effect algorithms were created by a development system that integrated into Microsoft Developer Studio. The effects were written in a language similar to C, and compiled into native FX8010 object code by its compiler, fxasm.[3]
The Sound Blaster Live! featured higher audio quality than previous Sound Blasters, as it processed the sound digitally at every stage, and because of its greater chip integration that reduced the analog signal losses of older, larger cards. Unfortunately, digital processing brought some limitations. The DSP had an internal fixed sample rate of 48kHz, a standard AC'97 clock, meaning that the EMU10K1 always captured external audio-sources at 48kHz, then performed a sample rate conversion on the 48kHz waveform to the requested target rate (such as 44.1kHz or 32kHz). This rate conversion step introduced intermodulation distortion into the downsampled output. However, the rate conversion was only applied when the audio signal was passed through the effects engine.[4] The Sound Blaster Live! card had great difficulty with resampling audio CD source material (at 44.1kHz) without introducing audible distortion. Creative addressed this concern by recommending recording audio exclusively at 48kHz and using third-party software to handle the desired sample rate conversion to avoid using the EMU10K1's sample rate conversion.
Sound Blaster Live! supported multi-speaker output, initially up to a four-speaker setup. The software referred to this as a "4.1" setup, meaning 4 satellites and a subwoofer. While this is the case, the subwoofer is not on a separate output as it is with 5.1 and higher audio. Instead, a low-pass filter (crossover) within the speaker system removes high and midrange frequencies from the sound card's output for the subwoofer. Games see a "4.1" speaker system as quadraphonic because DirectSound itself offers no subwoofer output in this configuration.[5] This is not limited to Creative sound cards; Aureal, Ensoniq, Philips, and other manufacturers have made cards that use four-speaker output in the same fashion. Later versions of the Live!, usually called Live! 5.1, offered 5.1-channel support which adds a center-channel speaker and LFE subwoofer output, most useful for movie watching where Dolby Digital 5.1 is decoded.
The Live! implemented DOS legacy support via Ensoniq's AudioPCI DOS TSR program. Creative acquired Ensoniq in 1998 and, as part of the deal, made use of this highly compatible ISA sound card emulator with their newer cards. In fact, the Live! uses ".ecw" (Ensoniq Concert Wavetable) files for the wavetable emulation in DOS. The program enables support for many standards, such as Sound Blaster 16, General MIDI, AdLib (OPL3), among others.
Sound Blaster Live! was the first sound card from Creative with the "What U Hear" recording input source. This was supported in the Windows drivers, so no additional software was needed to utilize it. The analog stereo audio signal that came out of the main Line Out was directed into this input. That way, one could mix all available inputs and the MIDI synth into one stereo signal. When using "What U Hear" with 5.1 sound, the sound would be downmixed to stereo first. The Creative Recorder utility included with the sound card was specifically designed to take advantage of the "What U Hear" feature, making it a simple matter to capture streaming sound from any source, even from programs that deliberately avoid providing a means for saving the digital sounds, thus freeing non-technical users from the complexities of "patching" between inputs and outputs of various software modules.
Design shortcomings
The original SB Live! had a very low noise floor for its time; however, a critical design flaw limited its application in quadraphonic audio. The two S/PDIF channels that each provided a stereo pair differed in their Digital to Analog reconstruction. Since the AC'97 chip provided an internal 48kHz DAC, Creative chose not to implement two identical DAC pipelines, and the front-speaker audio pair was subjected to a different reconstruction and amplification regime to that of the rear channel (as evidenced by differently valued pull-up resistors and filter capacitors in the area forward of the AC'97 chip, in the specifications of the AC'97 itself, and in the use of different amplifier Op-Amps).
The rear channel was serviced by a separate, but arguably better Philips UDA1334 DAC, yet the Op-Amp used to boost the signal to output levels had a noticeably different frequency response envelope that was not normalized to the front channel, leaving a "thin and quiet" rear channel. To make matters worse, the rear channel Op-Amp was of the inverting variety without being treated as such, leaving the rear speakers out of phase with the front, requiring switchover. These problems were not encountered by those using the Gold editions' daughterboard 4-speaker digital-output, but the tendency of the AC'97 chip to fail when used as an input source to medium-impedance musical instruments removed the use of the front channels altogether, although the chip could be sourced from cheaper AC'97 compatible products and soldered into place. Nevertheless, simply redirecting front signal to rear output of SB Live! was for a long time a favorite trick for computer audio enthusiasts who want better sound for minimum of money.
Despite these problems, the original SB Live! can still be used well as a S/PDIF input/output and MIDI input/output device for network-connected digital audio workstation environments.
Models
Sound Blaster Live! and Live! Value
Sound Blaster Live! Value.
The Live! and Live! Value are the original releases of the Live! family.
The Live! Value (also known as Live! 1024) is identical to the full Live! with the exception that it has color-coded plastic connectors instead of gold and does not include the extended digital I/O card. The original Sound Blaster Live! had a proprietary 9-pin mini-DIN connector for digital output that Creative referred to as the "Mini Din." This connector allowed the use of a microphone and digital speakers at the same time. This cannot be done with the value and base models of all subsequent Creative sound cards, as they share a single port for S/PDIF digital in/output and microphone connectivity. The Mini-DIN connection was not included in any subsequent Sound Blaster product, however owners of speaker systems that use this as the only digital input may buy an adapter from Creative.[verification needed]
Creative Sound Blaster Live! 1024 soundcard side view (connectors)
Creative Sound Blaster Live! 1024 soundcard back view (soldering)
Creative Sound Blaster Live! 1024 soundcard 3D view with chips
Driver CD of Sound Blaster Live! 1024 sound card
Sound Blaster Live! Platinum
Released 1999. Includes Live! Drive IR.
Sound Blaster Live! 5.1 and Sound Blaster Live! Platinum 5.1
Released 2000. Live! with added outputs for a center channel speaker and LFE subwoofer channel. This minijack is shared and provide the C+LFE channels in analog mode; otherwise, when Digital Out is activated this minijack provide an S/PDIF coaxial output feature, with the ability of playback stereo or AC3 pass-thru. Not all models have this feature. Some well known models that support it are as follows: SB0060, SB0100, SB0102, SB0220. This mode must be activated in the sound mixer with "Digital Output Only" checkbox and is exclusive (not possible to use analog and digital at the same time).
Sound Blaster Live! Dell OEM
Sound Blaster Live! Dell OEM
This card, marketed as a Sound Blaster Live!, did not have the full capabilities of the retail versions of Live! It used a different audio chip, not EMU10K1 but EMU10K1X, that is noticeably smaller with fewer pins. The chip does not accelerate DirectSound in hardware, nor EAX. The sale of this board by Dell created some controversy because it was not obviously marketed as an inferior or cheaper product. The card can be identified by its part number (SB0200/0203).
Sound Blaster Live! 5.1 Digital (Dell OEM, SB0220)
This was a later, improved model. The EMU10K1 chip was restored, as was hardware EAX/DirectSound/DirectSound3D acceleration. Currently there are Windows drivers available for download from Creative's website (filename: (Dell) Driver Install Pack 2_10 Languages). It was recommended that recording should be done at 48kHz sampling rate, as there was an issue with hardware downsampling.
Sound Blaster Live! 24-bit
The Sound Blaster Live! 24-bit (SB0410) was not actually a member of the Sound Blaster Live! family, because it lacked the EMU10k1/10k2 processor. It was a stripped-down version of the Audigy Value, with an SNR of 100dB, software based EAX, no advanced resolution DVD-Audio Playback, and no Dolby Digital 5.1 or Dolby Digital EX 6.1 playback. Evidence for this is that on Linux operating systems, when using the ALSA sound system, the module that is used for the Sound Blaster Live! 24-bit is snd-ca0106, while the module that is used by the Sound Blaster Live! is snd-emu10k1.
E-MU APS (Audio Production Studio)
This was a series of professional sound cards made by E-mu which was owned by Creative and had developed the EMU10K1 DSP chip featured on Creative's Live! products. Based on the later EMU10K2 chip, model numbers include 0404, 1212, 1616, and 1820. Their professional features included effects with higher quality, front-mounted drive bay panel with headphone output, dual mic/line inputs with physical level control knobs, digital coax in/out on both PCI card and drive bay, mixer with dB precision, phantom power for microphones (12V), ASIO, mixer presets, internal mixer rerouting, 64 MIDI channels, 32MB system RAM usage for SF2 (Gigabyte expandable in Windows XP) and future expandability through an extra multi-out card. They also featured line in and line out; all analogue inputs and outputs were balanced ¼"/6.3mm TRS jacks.[6][7]
A sound card is an internal expansion card that provides input and output of audio signals to and from a computer under the control of computer programs. The term sound card is also applied to external audio interfaces used for professional audio applications.
Sound Blaster is a family of sound cards and audio peripherals designed by Singaporean technology company Creative Technology. The first Sound Blaster card was introduced in 1989.
Pro Tools is a digital audio workstation (DAW) developed and released by Avid Technology for Microsoft Windows and macOS. It is used for music creation and production, sound for picture and, more generally, sound recording, editing, and mastering processes.
The Environmental Audio Extensions are a number of digital signal processing presets for audio, present in Creative Technology Sound Blaster sound cards starting with the Sound Blaster Live and the Creative NOMAD/Creative ZEN product lines. Due to the release of Windows Vista in 2007, which deprecated the DirectSound3D API that EAX was based on, Creative discouraged EAX implementation in favour of its OpenAL-based EFX equivalent – though at that point relatively few games used the API.
Ensoniq Corp. was an American electronics manufacturer, best known throughout the mid-1980s and 1990s for its musical instruments, principally samplers and synthesizers.
The Gravis UltraSound or GUS is a sound card for the IBM PC compatible system platform, made by Canada-based Advanced Gravis Computer Technology Ltd. It was very popular in the demoscene during the 1990s.
There have been various families of Yamaha audio controllers labelled as YMF7xx.
Sound Blaster X-Fi is a lineup of sound cards in Creative Technology's Sound Blaster series.
Soundscape S-2000 was Ensoniq's first direct foray into the PC sound card market. The card arrived on the market in 1994. It is a full-length ISA digital audio and sample-based synthesis device, equipped with a 2 MiB Ensoniq-built ROM-based patch set. Some OEM versions of the card feature a smaller 1 MiB patch set. It was praised for its then-high quality music synthesis and sound output, high compatibility and good software support.
The Ensoniq Soundscape OPUS (SS-3016-NCD) is a Gateway 2000 OEM sound card, and possibly was used by other OEMs, but was never sold to Ensoniq's customers directly. It was a Soundscape-like board, using the Ensoniq "OPUS" multimedia sound chip that only was used on these OEM boards. It had a 1MB patch set ROM chip, resulting in a lesser MIDI quality compared to the Soundscape and Soundscape ELITE. The "OPUS" cards again carry the Motorola 68EC000 CPU. The variety of CD-ROM interfaces have been removed. Otherwise, however, the card is simply a cost-reduced Soundscape-compatible board with similar capabilities.
The Soundscape Elite was Ensoniq's high-end ISA PC sound card offering. It offers the highest MIDI quality of any PC sound card Ensoniq produced. The board is an evolution of the company's previous Soundscape S-2000. The Soundscape ELITE was launched in March 1995.
The Ensoniq AudioPCI is a Peripheral Component Interconnect (PCI)-based sound card released in 1997. It was Ensoniq's last sound card product before they were acquired by Creative Technology. The card represented a shift in Ensoniq's market positioning. Whereas the Soundscape line had been made up primarily of low-volume high-end products full of features, the AudioPCI was designed to be a very simple, low-cost product to appeal to system OEMs and thus hopefully sell in mass quantities.
Sound Blaster Audigy is a product line of sound cards from Creative Technology. The flagship model of the Audigy family used the EMU10K2 audio DSP, an improved version of the SB-Live's EMU10K1, while the value/SE editions were built with a less-expensive audio controller.
The Sound Blaster 16 is a series of sound cards by Creative Technology, first released in June 1992 for PCs with an ISA or PCI slot. It was the successor to the Sound Blaster Pro series of sound cards and introduced CD-quality digital audio to the Sound Blaster line. For optional wavetable synthesis, the Sound Blaster 16 also added an expansion-header for add-on MIDI-daughterboards, called a Wave Blaster connector, and a game port for optional connection with external MIDI sound modules.
Sound Blaster Advanced Wave Effects 64 ISA sound card from Creative Technology. It is an add-on board for PCs. The card was launched in November 1996.
Windows Sound System (WSS) is a sound card specification developed by Microsoft, released at the end of 1992 for Windows 3.1. It was sold as a bundle which included an ISA sound card, a microphone, a pair of headphones and a software package.
The Wave Blaster was an add-on MIDI-synthesizer for Creative Sound Blaster 16 and Sound Blaster AWE32 family of PC soundcards. It was a sample-based synthesis General MIDI compliant synthesizer. For General MIDI scores, the Wave Blaster's wavetable-engine produced more realistic instrumental music than the SB16's onboard Yamaha-OPL3.
E-mu Systems was a software synthesizer, audio interface, MIDI interface, and MIDI keyboard manufacturer. Founded in 1971 as a synthesizer maker, E-mu was a pioneer in samplers, sample-based drum machines and low-cost digital sampling music workstations.
Creative Technology Ltd., or Creative Labs Pte Ltd., is a Singaporean multinational technology company. The principal activities of the company and its subsidiaries consist of the design, manufacture and distribution of digitized sound and video boards, computers and related multimedia and personal digital entertainment products. It also partners with mainboard manufacturers and laptop brands to embed its Sound Blaster technology on their products.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
