A transmission line loudspeaker is a loudspeaker enclosure design which uses the topology of an acoustic transmission line within the cabinet, compared to the simpler enclosures used by sealed (closed) or ported (bass reflex) designs. Instead of reverberating in a fairly simple damped enclosure, sound from the back of the bass speaker is directed into a long (generally folded) damped pathway within the speaker enclosure, which allows far greater control and use of speaker energy and the resulting sound.
Inside a transmission line (TL) loudspeaker is a (usually folded) pathway into which the sound is directed. The pathway is often covered with varying types and depths of absorbent material, and it may vary in size or taper, and may be open or closed at its far end. Used correctly, such a design ensures that undesired resonances and energies, which would otherwise cause undesirable auditory effects, are instead selectively absorbed or reduced ("damped") due to the effects of the duct, or alternatively only emerge from the open end in phase with the sound radiated from the front of the driver, enhancing the output level ("sensitivity") at low frequencies. The transmission line acts as an acoustic waveguide, and the padding both reduces reflection and resonance, and also slows the speed of sound within the cabinet to allow for better tuning.
Transmission line loudspeakers designs are more complex to implement, making mass production difficult, but their advantages have led to commercial success for a number of manufacturers such as IMF, TDL, and PMC. As a rule, transmission line speakers tend to have exceptionally high fidelity low frequency response far below that of a typical speaker or subwoofer, reaching into the infrasonic range (British company TDL's studio monitor range from the 1990s quoted their frequency responses as starting from as low as 17Hz depending upon model with a sensitivity of 87dB for 1W @ 1meter), without the need for a separate enclosure or driver.[1][2] Acoustically, TL speakers roll off more slowly (less steeply) at low frequencies, and they are thought to provide better driver control than standard vented-box cabinet designs,[3] are less sensitive to positioning, and tend to create a very spacious soundstage. Modern TL speakers were described in a 2000 review as "match[ing] reflex cabinet designs in every respect, but with an extra octave of bass, lower LF distortion and a frequency balance which is more independent of listening level".[4]
Although more complex to design and tune, and not as easy to analyze and calculate as other designs, the transmission line design is valued by several smaller manufacturers, as it avoids many of the major disadvantages of other loudspeaker designs. In particular, the basic parameters and equations describing sealed and reflex designs are fairly well understood, the range of options involved in a transmission line design mean that the general design can be somewhat calculated but final transmission line tuning requires considerable attention and is less easy to automate.
Purpose and design overview
Low frequencies, which remain in phase, emerge from the vent which essentially acts as a second driver. The advantage of this approach is that the air pressure loading the main driver is maintained which controls the driver over a wide frequency range and reduces distortion. [The TL design] also produces higher SPL [sensitivity or loudness] and lower bass extension than ported or sealed box of similar size.
I have an intuitive abhorrence of resonance enhancement to give a loudspeaker more "kick" or apparent bass as they can sound "single-noted". Yes you can pick out the bass rhythm but what about the melody. What a transmission line gives in my experience is a much smoother and more realistic bass quality.
- Steve Davey, former TNT Audio staff member/reviewer[6]
A transmission line is used in loudspeaker design to reduce time, phase, and resonance related distortions, and in many designs to gain exceptional bass extension to the lower end of human hearing, and in some cases the near-infrasonic (below 20Hz). TDL's 1980s reference speaker range (now discontinued) contained models with frequency ranges of 20Hz upwards, down to 17Hz upwards, without needing a separate subwoofer.[2]Irving M. Fried, an advocate of TL design, stated that:
"I believe that speakers should preserve the integrity of the signal waveform and the Audio Perfectionist Journal has presented a great deal of information about the importance of time domain performance in loudspeakers. I’m not the only one who appreciates time- and phase-accurate speakers but I have been virtually the only advocate to speak out in print in recent years. There’s a reason for that."
"It is difficult and costly to design and manufacture a time- and phase-accurate speaker system. Few of today’s high-end loudspeakers are time- and phase-accurate designs. The audio magazines need to appeal to a broad spectrum of advertisers including many who make speaker systems which are time incoherent. The magazines, and the reviewers who write for them, have ignored or downplayed the issue of time- and phase-accuracy in order to maximize advertising revenue. I am not alone in recognizing this situation."[7]
Some proponents of TL loudspeakers consider that using a TL is the theoretical ideal manner in which to load a moving-coil drive unit.[citation needed] However, it is also one of the more complex of constructions. The most common and practical implementation is to fit a drive unit to the end of a long duct that is usually open at the far end. In practice, the duct is folded inside a conventional shaped cabinet, so that the open end of the duct appears as a vent on the speaker cabinet. There are many ways in which the duct can be folded, and the line is often tapered in cross section to avoid parallel internal surfaces that encourage standing waves. Some speaker designs also use a spiral or elliptic spiral shaped duct, usually with one speaker element in the front or two speaker elements arranged one on each side of the cabinet. Depending upon the drive unit, and quantity and various physical properties of absorbent material, the amount of taper will be adjusted during the design process to tune the duct to remove irregularities in its response. The internal partitioning provides substantial bracing for the entire structure, reducing cabinet flexing and colouration. The inside faces of the duct or line, are treated with an absorbent material to provide the correct termination with frequency to load the drive unit as a TL. The enclosure behaves like an infinite baffle, potentially absorbing most or all of the speaker unit's rear energies.[8] A theoretically perfect TL would absorb all frequencies entering the line from the rear of the drive unit but remains theoretical, as it would have to be infinitely long. The physical constraints of the real world, demand that the length of the line must often be less than 4 meters before the cabinet becomes too large for any practical applications, so not all the rear energy can be absorbed by the line. In a realized TL, only the upper bass is TL loaded in the true sense of the term (i.e. fully absorbed); the low bass is allowed to freely radiate from the vent in the cabinet. The line therefore effectively works as a low pass filter, another crossover point in fact, achieved acoustically by the line and its absorbent filling. Below this “crossover point” the low bass is loaded by the column of air formed by the length of the line. The length of the line is specified so as to reverse the phase of the rear output of the drive unit as it exits the vent. This acoustic energy combines with the output of the bass unit, extending its response and effectively creating a second driver.
Cutaway drawing of a commercial 4-way transmission line loudspeaker system, the IMF Reference Standard Professional Monitor Mk VII (circa 1982). The enclosure is 104cm (41in) high (116cm (46in) on its stand), 43cm (17in) deep and 50cm (20in) wide, with a gross enclosure volume of about 218liters. The efficiency using pink noise at 1meter is 80–82dB at 1watt, depending upon the filter/equalisation settings. Frequency response was quoted to be 17Hz to 40kHz, with crossover frequencies of 350Hz, 3kHz and 13kHz. The drive units consisted of a 30 by 21cm (11.8 by 8.3in) styrene/fibreglass woofer, 13cm (5.1in) engineered polymer midrange, 4.5cm (1.8in) ferro-fluid damped tweeter, and 2cm (0.79in) ferro-fluid damped chemical-dome high-frequency tweeter.
Essentially, the goal of the transmission line is to minimize acoustical or mechanical impedance at frequencies corresponding to the fundamental free-air resonance of the bass driver. This simultaneously reduces stored energy in the driver's motion, reduces distortion, and critically damps the driver by maximizing acoustic output (maximal acoustical loading or coupling) at the terminus. This also minimizes the negative effects of acoustic energy that would otherwise (as with a sealed enclosure) be reflected back to the driver in a sealed cavity.[9]
Transmission line loudspeakers employ this tube-like resonant cavity, with the length set between 1/6 and 1/2 the wavelength of the fundamental resonant frequency of the loudspeaker driver being used. The cross-sectional area of the tube is typically comparable to the cross-sectional area of the driver's radiating surface area. This cross section is typically tapered down to approximately 1/4 of the starting area at the terminus or open end of the line. While not all lines use a taper, the standard classical transmission line employs a taper from 1/3 to 1/4 area (ratio of terminus area to starting area directly behind driver). This taper serves to dampen the buildup of standing waves within the line, which can create sharp nulls in response at the terminus output at even multiples of the driver's Fs.
In a transmission line speaker, the transmission line itself can be open ("vented") or closed at the far end. Closed designs typically have negligible acoustic output from the enclosure except from the driver, while open ended designs exploit the low-pass filter effect of the line, and the resultant low bass energy emerges to reinforce the output from the driver at low frequencies. Well designed transmission line enclosures have smooth impedance curves, possibly from a lack of frequency-specific resonances, but can also have low efficiency if poorly designed.
One key advantage of transmission lines is their ability to conduct the back wave behind the transducer more effectively away from it – reducing the chance for reflected energy permeating back through the diaphragm out of phase with the primary signal. Not all transmission lines designs do this effectively. Most offset transmission line speakers place a reflective wall fairly close behind the transducer within the enclosure – posing a problem for internal reflections emanating back through the transducer diaphragm. Older descriptions explained the design in terms of "impedance mismatch", or pressure waves "reflected" back into the enclosure; these descriptions are now considered outdated and inaccurate as technically the transmission line works through selective production of standing waves and constructive and destructiveinterference (see below).
A second benefit is that the resulting music is time coherent (i.e., in phase). Fried quoted in 2002, a listening test performed and reported in December 2000's Hi-Fi News (as he believed) in which a high-quality recording was obtained using reputable but non-time-coherent loudspeakers and this recording was then time phase corrected; an expert listening panel "voted unanimously for the superior realism and accuracy of the time corrected output" for high quality sound reproduction.[7]
One of the significant and common problems with a transmission line loudspeaker system is the unwanted phase-cancellation effects of higher line harmonics bleeding from the transmission line and adversely affecting the overall sound field. For example, in the PMC PMC6 mid-sized transmission line monitoring loudspeaker, there is a dip around 300Hz that is caused by the fifth harmonic of the transmission line’s resonant frequency.[10] This type of problem is quite common, and it was readily apparent in other transmission line loudspeakers. For example, the large IMF TLS80 MkII from 1977 also had an anomaly, but this time at the lower frequency of about 140Hz, consisting of an almost one-octave-wide deleterious 2-dB dip in the on-axis response.[11] Another problem is that the sound radiation from the exit of the line is spread over a quite broad frequency range caused by the hump of the quarter-wave transmission line resonance, whereas the high-Q port resonance of a vented-box loudspeaker rolls off much more quickly and extends over a much narrower frequency band.[12] These sorts of issues with transmission line loudspeakers can lead to tonal accuracy problems that cannot be resolved.
A transmission line speaker employs, essentially, two distinct forms of bass loading, which historically and confusingly have been amalgamated in the TL description. Separating the upper and lower bass analysis reveals why such designs have so many potential advantages and disadvantages over reflex and infinite baffle designs. Measurements indicate that the upper bass is only partially absorbed by the line, making a clean and neutral response somewhat difficult if not impossible to achieve. The lower bass is extended and distortion is lowered by the line's control over the drive unit's excursion. One of the exclusive benefits of a TL design is its ability to produce very low frequencies even at low monitoring levels – TL speakers can routinely produce full range sound usually requiring a subwoofer, and do so to very high levels of low-frequency accuracy. The main disadvantage of the design is that it is more labor-intensive to create and tune a high quality and consistent transmission line, compared to building a simple vented-box or closed-box enclosure. One PMC employee was quoted as saying that optimising a transmission line loudspeaker is "like juggling water".[12] A 2010 Hifi Avenue TL speaker review commented that "One thing I have noticed about transmission line designs is that they create a rather big soundstage and seem to handle crescendoes with ease".[5]
History of transmission line loudspeakers
Invention and early use
This image is actually an inverted folded horn. It is distinguished from a true transmission line enclosure, which has the same vent width throughout, by having a throat that is wider than its port opening.
The concept was innovated within acoustic enclosure design, and originally termed an "acoustical labyrinth", by acoustic engineer and later Director of Research, Benjamin Olney, who developed the concept at the Stromberg-Carlson Telephone Co. in the early 1930s while studying the effect of enclosure shape and size on speaker output, including the effect of "extreme length in a box baffle".[13] A patent was filed in 1934.[14] The design was used in their console radios beginning in 1936.[15] A loudspeaker enclosure based on the concept was proposed in October 1965 by Dr A.R. Bailey in Wireless World magazine, referencing a production version of an acoustic-line enclosure design from Radford Electronics Ltd.[16] The article postulated that energy from the rear of a driver unit could be essentially absorbed, without damping the cone's motion or superimposing internal reflections and resonance, so Bailey and Radford reasoned that the rear wave could be channelled down a long pipe. If the acoustic energy was absorbed, it would not be available to excite resonances. A pipe of sufficient length could be tapered, and stuffed so that the energy loss was almost complete, minimizing output from the open end. No broad consensus on the ideal taper (expanding, uniform cross-section, or contracting) has been established.
"Classic" era transmission line loudspeakers
Source for much of this section: Loudspeakers: for music recording and reproduction (Newell & Holland, 2007)[17]
The birth of the modern transmission line speaker design came about in 1965 with the publication of A.R. Bailey's article in Wireless World, “A Non-resonant Loudspeaker Enclosure Design”,[16] detailing a working Transmission Line. Bailey followed up his first article with a second one in 1972.[18] Radford Electronics Ltd took up this innovative design and briefly manufactured the first commercial Transmission Line loudspeaker. Although acknowledged as the father of the Transmission Line, Bailey's work drew on the work on labyrinth design, dating back as early as the 1930s. His design, however, differed significantly in the way in which he filled the cabinet with absorbent materials. Bailey hit upon the idea of absorbing all the energy generated by the bass unit inside the cabinet, providing an inert platform for the drive unit to work from; unchecked, this energy produces spurious resonances in the cabinet and its structure, adding distortion to the original signal.
Shortly thereafter the design entered mainstream Hi-Fi, through the works of Irving M. "Bud" Fried in the United States, and a British trio: John Hayes, John Wright, and David Brown. Dave D'Lugos describes the period that followed (approximately 35 years until the start of the 21st Century) as a period when the "classical designs" were created.
Fried was exposed during his time at Harvard University to high fidelity audio reproduction, and later became an importer of audiophile items. Under the trademark "IMF" (his initials), from 1961, he eventually became involved with many advancements in audiophile equipment: cartridges (IMF – London, IMF – Goldring), tonearms (SME, Gould, Audio and Design), amplifiers (Quad, Custom Series), loudspeakers (Lowther, Quad, Celestion, Bowers and Wilkins, Barker, etc.).[19] In 1968 he met John Hayes and John Wright, who had already designed an award-winning tonearm in the UK and had brought along a transmission line speaker designed by John Wright — described by Hayes as "fanatical regarding quality"[7]— in order to promote and demonstrate the tonearm at a New York hifi show. Fried unexpectedly received a number of orders for the unnamed speaker, which he dubbed the "IMF".[7] The British pair, along with Hayes' colleague David Brown, agreed to form a UK company to design and manufacture speakers which would be sold by Fried in the United States. John Hayes later wrote that:
Of course, Bud, had called it the IMF, and therefore, perhaps mistakenly we registered IMF and formed an IMF company... At no time did Bud Fried have any input on the designs. We sold him speakers and he was the US Distributor...[7] [...] Bud Fried was never a Director or shareholder of IMF Electronics. IMF electronics were the only company manufacturing the transmission line speakers. The name IMF was adopted because Bud Fried had demonstrated the first prototype speakers at the New York hi fi show, and because of the publicity and the fact that he had used his name on the then unnamed speakers, we stuck with the name which was a mistake on our part. It was never his company. After our lawsuit he called his speakers Fried.[7]
The relationship broke down acrimoniously when Fried began to make his own, poorer quality speakers, also marketed as "IMF", and refused to cease until a court agreed that the UK business had the right to the trademark IMF for loudspeakers.[7] Following the split, Fried in the USA (under the brandname "Fried") and the three founders of IMF Electronics in the UK (via a joint venture with driver manufacturer Elac under the name TDL), both became well known in audiophile circles for many years as major advocates of transmission line speaker design.[7] TDL closed after John Wright's gradual failing health and death in 1999 from cancer.[7] He was described in his 1999 obituary as "one of the most important figures on the British hi-fi scene since the mid-1960s... best remembered for his transmission-line loudspeaker designs".[20] The brand was acquired by Audio Partnerships (part of retailer group Richer Sounds). Fried died six years later, in 2005.[21]
21st century
In the early 21st century, mathematical models that seemed to approximate the behavior of real-world TL speakers and cabinets began to emerge.[22] According to the website t-linespeakers.org, this led to an understanding that what he termed the "classical" speakers, designed largely by "trial and error", were a "good job" and the best that was reasonably possible at those time, but that better designs were now achievable based on modeled responses.[23]
Design principles
Fig. 1 - Relationship between TL length and wavelengthFig. 2 - Frequency response (magnitude) measurement of drive unit and TL outputs
Phase inversion is achieved by selecting a length of line that is equal to the quarter wavelength of the target lowest frequency. The effect is illustrated in Fig. 1, which shows a hard boundary at one end (the speaker) and the open-ended line vent at the other. The phase relationship between the bass driver and vent is in phase in the pass band until the frequency approaches the quarter wavelength, when the relationship reaches 90degrees as shown. However, by this time the vent is producing most of the output (Fig. 2). Because the line is operating over several octaves with the drive unit, cone excursion is reduced, providing higher SPLs and lower distortion levels, as compared with bass reflex and infinite baffle loudspeaker enclosure designs.
The complex loading of the bass drive unit demands specific Thiele-Small driver parameters to realise the full benefits of a TL design. Most drive units in the marketplace are developed for the more common reflex and infinite baffle designs and are usually not suitable for TL loading. High efficiency bass drivers with extended low frequency ability, are usually designed to be extremely light and flexible, having very compliant suspensions. Whilst performing well in a reflex design, these characteristics do not match the demands of a TL design. The drive unit is effectively coupled to a long column of air which has mass. This lowers the resonant frequency of the drive unit, negating the need for a highly compliant device. Furthermore, the column of air provides greater force on the driver itself than a driver opening onto a large volume of air (in simple terms it provides more resistance to the driver's attempt to move it), so to control the movement of air requires an extremely rigid cone, to avoid deformation and consequent distortion.
The introduction of the absorption materials reduces the velocity of sound through the line, as discovered by Bailey in his original work. Bradbury published his extensive tests to determine this effect in an AES journal article in 1976,[24] and his results agreed that heavily damped lines could reduce the velocity of sound by as much as 50%, although 35% is typical in medium damped lines. The behaviour of various damping materials has also been studied by Lusztak and Bujacz.[25] Bradbury's tests were carried out using fibrous materials, typically longhaired wool and glass fibre. However, these kinds of materials produce highly variable effects that are not consistently repeatable for production purposes. They are also liable to produce inconsistencies due to movement, climatic factors and effects over time. High specification acoustic foams, developed by manufacturers such as PMC, with similar characteristics to longhaired wool, provide repeatable results for consistent production. The density of the polymer, the diameter of the pores and the sculptured profiling are all specified to provide the correct absorption for each speaker model. The quantity and position of the foam is critical to engineer a low-pass acoustic filter that provides adequate attenuation of the upper bass frequencies, whilst allowing an unimpeded path for the low bass frequencies. Although the result may require a lot of modeling and testing, the starting point is usually based on one of three basic principles. Filling the entire tube treats the TL as a damper, aiming at completely eliminating the rear wave. Filling half the cross section throughout the line's entire length treats the TL as an infinite baffle, basically damping high frequencies and wall-to-wall resonances. Filling the tube from the driver to half the tube's length aims at a quarter-wave resonator, leaving the fundamental tone with its velocity maxima at the open end of the tube intact, while damping all the overtones.
Mathematical equations, modelling, and design process
The external links section of this article links to a number of resources that detail the mathematical principles, models, and DIY calculations, as well as extended practical design material, related to transmission line speakers.
For most of the 20th century, transmission line design remained more of an art than a science, requiring much trial and error. Jon Risch states in an article on classic transmission line design, that the hard part was finding the best stuffing density along the line's length, because "the line stuffing affects both the total apparent line length AND the total apparent box volume simultaneously". He summarized the state of design at the time as:[26]
"The classic transmission line bass enclosure has never been completely and successfully modeled such that it can be built from a pat set of equations. Some claim to have done this, but it doesn't seem to allow a first time build without adjustments, so the models have enough wrong to require a fudge factor..."[26]
Dave D'Lugos, founder of fan site t-linespeakers.org, comments that this reflects the "classical" designs from the 1960s until Risch's writing, during which period "TL design was seat of the pants".[23]
However, from the 21st Century, Martin King and George Augspurger (both separately and referencing each other's works), produced models which show these to be "generally less than optimal" designs which "did a good job of approaching what was possible in their day". Audio engineer Augspurger had modeled TLs using an electrical analogy,[22] and found it to agree closely with King's existing work, based on a mechanical analogy.[23] D'Lugos concluded in his overview of TL modeling and design theory: "I think that using modern drivers and tools such as King's software you can build a better TL easier today".[23]
More recently, Andrea Rubino has developed a sophisticated simulation model based on electrical circuit theory and published a series of articles in the Italian electroacoustic journal AUDIOreview. Many resources are available on his website: transmissionlinespeakers.com
In addition to these more sophisticated models a number of approximation algorithms exist. One such is to design a closed-box loudspeaker enclosure, then building a transmission line of the same volume tuned to the closed-box loudspeaker's resonance frequency. Another is to design a bass reflex loudspeaker, again building a transmission line of the same volume, tuned to the frequency of the Helmholtz resonator.
Prominent individuals and companies
Pioneers:
Benjamin Olney – originated the idea of a duct in speaker enclosure design, which he termed an "acoustic labyrinth", while working for Stromberg-Carlson as an acoustic engineer and studying the effect of enclosure size on output sound.
Bailey and Radford – worked together and developed the concept for loudspeakers (1965). Their design was a significant development from the earlier work. Bailey's name was on the article and Radford built the first commercial TL speaker.[16]
John Wright together with business partner John Hayes and (later) David Brown, and their company IMF Electronics Ltd (later: TDL) – Wright, a "fanatical" pursuer of quality, had designed an award winning tonearm and to demonstrate it, brought to New York a non-commercial TL speaker he had also designed. The speaker gained considerable attention and Wright, Hayes and colleague Brown formed a company that specialized in TL speakers, and won numerous awards (1968). TDL disbanded following Wright's death in 1999 and the brand—as a shell—was bought by Richer Sounds.
Irving M. "Bud" Fried – American audiophile and TL advocate, who encountered Wright and Hayes in 1968, recognized the potential of Wright's unnamed speaker, and began marketing their TL speakers in the United States. Later set up a TL company of his own to design speakers.
Bo Hansson – Swedish designer of HiFi equipment and founder of Opus3 Record Company created the "Rauna Njord" concrete speaker as a transmission line design.[27]
Martin King and George Augspurger – researchers and designers who succeeded in modeling realistic TL speaker designs in the early 21st century.
Other companies and individuals who have produced or researched TL speakers:
USA – New York Acoustics, loosely associated with New York Audio Labs , kits and plans for 8" and 10" driver TL speaker cabinets, active in the mid 1980s.
See also
Wikimedia Commons has media related to Loudspeaker .
Acoustic suspension – a method of loudspeaker cabinet design and utilisation that uses one or more loudspeaker drivers mounted in a sealed box or cabinet.
Bass reflex – a type of loudspeaker enclosure that uses a port (hole) or vent cut into the cabinet and a section of tubing or pipe affixed to the port.
A subwoofer is a loudspeaker designed to reproduce low-pitched audio frequencies, known as bass and sub-bass, that are lower in frequency than those which can be (optimally) generated by a woofer. The typical frequency range that is covered by a subwoofer is about 20–200 Hz for consumer products, below 100 Hz for professional live sound, and below 80 Hz in THX-certified systems. Thus, one or more subwoofers are important for high-quality sound reproduction as they are responsible for the lowest two to three octaves of the ten octaves that are audible. This very low-frequency (VLF) range reproduces the natural fundamental tones of the bass drum, electric bass, double bass, grand piano, contrabassoon, tuba, in addition to thunder, gunshots, explosions, etc.
A loudspeaker is a combination of one or more speaker drivers, an enclosure, and electrical connections. The speaker driver is an electroacoustic transducer that converts an electrical audio signal into a corresponding sound.
Audio crossovers are a type of electronic filter circuitry that splits an audio signal into two or more frequency ranges, so that the signals can be sent to loudspeaker drivers that are designed to operate within different frequency ranges. The crossover filters can be either active or passive. They are often described as two-way or three-way, which indicate, respectively, that the crossover splits a given signal into two frequency ranges or three frequency ranges. Crossovers are used in loudspeaker cabinets, power amplifiers in consumer electronics and pro audio and musical instrument amplifier products. For the latter two markets, crossovers are used in bass amplifiers, keyboard amplifiers, bass and keyboard speaker enclosures and sound reinforcement system equipment.
A woofer or bass speaker is a technical term for a loudspeaker driver designed to produce low frequency sounds, typically from 20 Hz up to a few hundred Hz. The name is from the onomatopoeic English word for a dog's deep bark, "woof". The most common design for a woofer is the electrodynamic driver, which typically uses a stiff paper cone, driven by a voice coil surrounded by a magnetic field.
An electrostatic loudspeaker (ESL) is a loudspeaker design in which sound is generated by the force exerted on a membrane suspended in an electrostatic field.
A horn loudspeaker is a loudspeaker or loudspeaker element which uses an acoustic horn to increase the overall efficiency of the driving element(s). A common form (right) consists of a compression driver which produces sound waves with a small metal diaphragm vibrated by an electromagnet, attached to a horn, a flaring duct to conduct the sound waves to the open air. Another type is a woofer driver mounted in a loudspeaker enclosure which is divided by internal partitions to form a zigzag flaring duct which functions as a horn; this type is called a folded horn speaker. The horn serves to improve the coupling efficiency between the speaker driver and the air. The horn can be thought of as an "acoustic transformer" that provides impedance matching between the relatively dense diaphragm material and the less-dense air. The result is greater acoustic output power from a given driver.
Thiele/Small parameters are a set of electromechanical parameters that define the specified low frequency performance of a loudspeaker driver. These parameters are published in specification sheets by driver manufacturers so that designers have a guide in selecting off-the-shelf drivers for loudspeaker designs. Using these parameters, a loudspeaker designer may simulate the position, velocity and acceleration of the diaphragm, the input impedance and the sound output of a system comprising a loudspeaker and enclosure. Many of the parameters are strictly defined only at the resonant frequency, but the approach is generally applicable in the frequency range where the diaphragm motion is largely pistonic, i.e., when the entire cone moves in and out as a unit without cone breakup.
A bass reflex system is a type of loudspeaker enclosure that uses a port (hole) or vent cut into the cabinet and a section of tubing or pipe affixed to the port. This port enables the sound from the rear side of the diaphragm to increase the efficiency of the system at low frequencies as compared to a typical sealed- or closed-box loudspeaker or an infinite baffle mounting.
A full-range loudspeaker drive unit is defined as a driver which reproduces as much of the audible frequency range as possible, within the limitations imposed by the physical constraints of a specific design. The frequency range of these drivers is maximized through the use of a whizzer cone and other means. Most single driver systems, such as those in radios, or small computer speaker designs, cannot reproduce all of the audible frequencies or the entire audible audio range.
The chief electrical characteristic of a dynamic loudspeaker's driver is its electrical impedance as a function of frequency. It can be visualized by plotting it as a graph, called the impedance curve.
A loudspeaker enclosure or loudspeaker cabinet is an enclosure in which speaker drivers and associated electronic hardware, such as crossover circuits and, in some cases, power amplifiers, are mounted. Enclosures may range in design from simple, homemade DIY rectangular particleboard boxes to very complex, expensive computer-designed hi-fi cabinets that incorporate composite materials, internal baffles, horns, bass reflex ports and acoustic insulation. Loudspeaker enclosures range in size from small "bookshelf" speaker cabinets with 4-inch (10 cm) woofers and small tweeters designed for listening to music with a hi-fi system in a private home to huge, heavy subwoofer enclosures with multiple 18-inch (46 cm) or even 21-inch (53 cm) speakers in huge enclosures which are designed for use in stadium concert sound reinforcement systems for rock music concerts.
Loudspeaker measurement is the practice of determining the behaviour of loudspeakers by measuring various aspects of performance. This measurement is especially important because loudspeakers, being transducers, have a higher level of distortion than other audio system components used in playback or sound reinforcement.
An isobaric loudspeaker is a loudspeaker in which two or more identical woofers operate simultaneously, with a common body of enclosed air adjoining one side of each diaphragm. They are most often used to improve low-end frequency response without increasing cabinet size, though at the expense of cost and weight. Isobaric loudspeakers were first introduced by Harry F. Olson in the early 1950s.
A speaker enclosure using a passive radiator usually contains an "active loudspeaker", and a passive radiator. The active loudspeaker is a normal driver, and the passive radiator is of similar construction, but without a voice coil and magnet assembly. It is not attached to a voice coil or wired to an electrical circuit or power amplifier. Small and Hurlburt have published the results of research into the analysis and design of passive-radiator loudspeaker systems. The passive-radiator principle was identified as being particularly useful in compact systems where vent realization is difficult or impossible, but it can also be applied satisfactorily to larger systems.
A guitar speaker is a loudspeaker – specifically the driver (transducer) part – designed for use in a combination guitar amplifier of an electric guitar, or for use in a guitar speaker cabinet. Typically these drivers produce only the frequency range relevant to electric guitars, which is similar to a regular woofer type driver, which is approximately 75 Hz — 5 kHz, or for electric bass speakers, down to 41 Hz for regular four-string basses or down to about 30 Hz for five-string instruments.
An acoustic transmission line is the use of a long duct, which acts as an acoustic waveguide and is used to produce or transmit sound in an undistorted manner. Technically it is the acoustic analog of the electrical transmission line, typically conceived as a rigid-walled duct or tube, that is long and thin relative to the wavelength of sound present in it.
Acoustic suspension is a loudspeaker cabinet design that uses one or more loudspeaker drivers mounted in a sealed box. Acoustic suspension systems reduce bass distortion which can be caused by stiff suspensions required on drivers used for open cabinet designs.
wOOx Technology is a brand created by Philips to identify loudspeaker systems that employ passive radiator technology along with active equalisation to maximize the output of the passive diaphragm. wOOx Technology optimizes the active bass driver, the passive bass radiator, and the active equalisation curve to obtain maximum low-frequency reproduction in a relatively compact configuration.
An electrodynamic speaker driver, often called simply a speaker driver when the type is implicit, is an individual transducer that converts an electrical audio signal to sound waves. While the term is sometimes used interchangeably with the term speaker (loudspeaker), it is usually applied to specialized transducers that reproduce only a portion of the audible frequency range. For high fidelity reproduction of sound, multiple loudspeakers are often mounted in the same enclosure, each reproducing a different part of the audible frequency range. In this case the individual speakers are referred to as drivers and the entire unit is called a loudspeaker. Drivers made for reproducing high audio frequencies are called tweeters, those for middle frequencies are called mid-range drivers and those for low frequencies are called woofers, while those for very low bass range are subwoofers. Less common types of drivers are supertweeters and rotary woofers.
The Linn Isobarik, nicknamed "Bariks" or "Briks", is a loudspeaker designed and manufactured by Linn Products. The Isobarik is known for both its reproduction of low bass frequencies and being very demanding on amplifiers.
↑ Olney, B. (1931). "Notes on Loud Speaker Response Measurements and Some Typical Response Curves". Proceedings of the Institute of Radio Engineers. 19 (7): 1111–1130. doi:10.1109/JRPROC.1931.222439. ISSN0731-5996. S2CID51674195.
↑ Bradbury, L.J.S. (1976). "The Use of Fibrous Materials in Loudspeaker Enclosures". Journal of the Audio Engineering Society. April: 404–412.
↑ Lusztak, Krzysztof; Bujacz, Michał (2012). Analysis of Damping Materials in a Transmission Line Loudspeaker System. New Trends in Audio and Video/Signal Processing Algorithms, Architectures, Arrangements and Applications, 27–29 September 2012, Łodż, Poland.
Quarter-wave.com – by Martin J King, developer of TL modeling software; also includes design calculations for professional and DIY TL speaker creation.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
