Triumph 6/1

Last updated

Triumph 6/1
Triumph 6-1.jpg
Triumph 6/1
Manufacturer Triumph Motor Company
Production1933-1935 [1]
AssemblyCoventry, UK
Successor Triumph Thunderbird
Class Heavyweight standard
Engine 649 cc [1] OHV parallel-twin
Bore / stroke 70 mm × 84 mm (2.8 in × 3.3 in) [2] [3]
Top speedest. 85 mph (137 km/h) [1] [2]
Power 25 bhp at 4,500 rpm [1] [2] [4]
Transmission Four speed manual, [5] handshift (footshift available in 1935) [1] [5]
Frame type Tubular steel dual downtube [5]
Suspension Girder fork, rigid rear [1] [5]
Brakes Linked 8 in (203 mm) drum brakes front and rear
Oil capacity7 imp pt (4.0 L) [6]

The Triumph 6/1 is a motorcycle that was made by Triumph at their Coventry factory from 1934 to 1936. Designed by Val Page, the 6/1 was the first Triumph motorcycle to use a parallel-twin engine. A sidecar-equipped 6/1 won a silver medal in the 1933 International Six Days Trial and went on to win the Maudes Trophy for 1933. The 6/1 was a commercial failure, selling fewer than 600 in two years on the market.



In conducting experiments with a single bank of Edward Turner's square four engine design, Turner and his supervisor, Ariel chief engineer Val Page both saw potential in the straight-twin as a motorcycle engine. From the experiments, it was shown that a 360° crank angle was better suited to the use of a single carburettor than a 180° crank angle. [2]

Page left Ariel in 1932 to become the chief motorcycle engineer at the Triumph Motor Company. [7] Page replaced all but one of Triumph's existing line of single-cylinder motorcycles with his designs. [6]

Design and specifications

In addition to redesigning Triumph's line of single-cylinder motorcycles, Page also designed a new twin-cylinder motorcycle. [6] The 6/1 was the first Triumph motorcycle with a parallel-twin engine to enter production. [2]

Closeup of tank, handlebars and front suspension Triumph 6-1 tank close up.jpg
Closeup of tank, handlebars and front suspension

The 6/1 was designed primarily for use as a sidecar hauler, [1] [8] mainly as a smaller, more economical alternative to the one litre V-Twins and fours usually used to pull sidecars at the time. [6] [8] As such, strength and durability were given priority, resulting in a large motorcycle weighing 412 pounds (187 kg). [5] [6] [8]

The engine was a 649 cc [1] [2] 360° parallel-twin with a 74 mm bore and an 80 mm stroke. [2] [3] [note 1] The cylinder barrels and individual heads for each cylinder were made from cast iron. [6] The crankcase was split vertically and held an oil tank with a capacity of 7 imperial pints (4.0 L). [3] Unlike Page's single cylinder designs for Triumph, which had double-plunger oil pumps and were the first Triumph motorcycles with enclosed valve gear, [6] the 6/1 had a single-plunger oil pump [6] and exposed valve gear [5] with double-coil valve springs and rocker shaft with grease nipples. [4] Induction was through a single 1" Amal Type 276 carburettor [4] [8] on a Y-shaped manifold [1] [4] The flywheel was positioned outside the left case, and the camshaft was positioned behind the cylinder bank. [3] The engine was positioned offset to the right in the frame. [8]

The four-speed gearbox [5] was bolted to the back of the engine crankcase [4] and was powered by double-helical gears, [3] and a nine-plate clutch. [6] The engine ran "backward", or counter to the rear wheel. [3] Shifting was initially by hand, but was changed to a foot-shift system in 1935. [5] The engine oil filter was mounted behind the gearbox. [1]

The 6/1 had 8 in (200 mm) drum brakes front and rear. The brakes were linked, and the rear wheel had a ratcheted "parking brake". [5]

Achievements and awards

Harry Perry, Triumph's sales manager, entered a Triumph 6/1 attached to a Triumph Gloria sidecar in the 1933 International Six Days Trial. Time lost repairing a front tyre cost him a gold medal; Perry returned to England with a silver medal in the sidecar class. The combination was then taken to Brooklands and, under the supervision of the Auto Cycle Union (ACU), was ridden 500 miles (805 km) in 498 minutes. [8] This test won Triumph the 1933 Maudes Trophy. [5] [8]


Speed Twin and 6/1 Triumph 5T Speed Twin and 6-1.jpg
Speed Twin and 6/1

At £76, the 6/1 was Triumph's most expensive motorcycle in 1934. [3] It was expensive to produce and, [5] with no parts interchangeable with any other Triumph motorcycle, there was no way to spread the costs out. [3] The heavyweight motorcycle/sidecar market for which the 6/1 had been developed was giving way to light motor cars like the Austin Seven, the Morris Eight, and Triumph's own Super 9. [8] As a result, the 6/1 was a commercial failure [3] and was discontinued in 1935. [1] Estimates of the total number built vary between 100 and 600. [3] [8]


Despite its achievements and awards, and despite being the first parallel-twin motorcycle from a manufacturer well known for parallel-twin motorcycles, the 6/1 is little remembered, having been overshadowed by Edward Turner's later and more successful Triumph Speed Twin. [2]

See also


  1. A two-cylinder engine with a 74 mm bore and an 80 mm stroke should displace 688 cc

Related Research Articles

Straight-twin engine inline piston engine with two cylinders

A straight-twin engine, also known as straight-two, inline-twin, vertical-twin, or parallel-twin is a two-cylinder piston engine which has its cylinders arranged side by side and its pistons connected to a common crankshaft. Compared to V-twins and flat-twins, straight-twins are more compact, simpler, and usually cheaper to make, but may generate more vibration during operation.

Coventry Victor was a British motorcycle and car manufacturer. Originally Morton & Weaver, a proprietary engine manufacturer in Hillfields, Coventry, founded in 1904, the company changed its name to Coventry Victor Motors in 1911, the company closed in 1971.

Yamaha XS 650 Yamaha motorcycle

The Yamaha XS650 is a mid-size motorcycle made by Yamaha Motor Company. The standard model was introduced in October 1969,and produced through 1979. The "Special" cruiser model was introduced in 1978 and produced through 1985. The XS650 began with the 1955 Hosk SOHC 500 twin. After about 10 years of producing 500 twin, Hosk engineers designed a 650 cc twin. Later the Hosk company was acquired by Showa Corporation, and in 1960 Yamaha had bought Showa with Hosk's early design of 650 cc twin.

Motorcycle engine engine that powers a motorcycle

A motorcycle engine is an engine that powers a motorcycle. Motorcycle engines are typically two-stroke or four-stroke internal combustion engines, but other engine types, such as Wankels and electric motors, have been used.

Triumph Thunderbird motorcycle by Triumph

The Triumph Thunderbird is a British motorcycle that was introduced by Triumph in 1949 and produced in many forms until 1966. The name was used three more times for new and distinct Triumph models.

BSA Rocket 3/Triumph Trident 1960s/1970s British motorcycle made by Triumph Engineering, Meriden

The Triumph Trident and BSA Rocket 3 was a technically advanced, high-performance roadster motorcycle made by Triumph Engineering and BSA from 1968 to 1975, and sold under both the Triumph and BSA marques. Alongside the Honda CB750, and later the Kawasaki triples, it brought a new level of sophistication to street motorcycles, marking the beginning of the superbike era. The Honda CB750 overshadowed the Trident to be remembered as the 'first superbike', in spite of the Triumph Trident actually debuting before the Honda by a few weeks.

Ducati L-twin engine

The next new Ducati engine to appear after the Ducati Apollo was the 90° V-twin, initial Grand Prix racing versions being 500 cc, and the production bikes were 750 cc. There was also the Ducati 750 Imola Desmo that won at Imola in 1972. These engines had bevel gear shaft drive to the overhead camshaft, and were produced in round, square, and Mille crankcases. In the 1980s these gave way to the belt drive camshaft engines that have continued to this day, in air-cooled and liquid-cooled form. The Mille used a plain bearing crank, like the belt models.

Douglas (motorcycles) British motorcycle manufacturer

Douglas was a British motorcycle manufacturer from 1907–1957 based in Kingswood, Bristol, owned by the Douglas family, and especially known for its horizontally opposed twin cylinder engined bikes and as manufacturers of speedway machines. The company also built a range of cars between 1913 and 1922.

BMW R60/2

The R60 and R60/2 are 600 cc boxer-twin that were manufactured from 1956 to 1969 in Munich, Germany, by BMW.

BMW R69S motorcycle

The R69S, R69US, and R69 are motorcycles, fitted with 594 cc boxer twin engines, that were manufactured by BMW in Munich, Germany.

Norton Commando

The Norton Commando is a British Norton-Villiers motorcycle with an OHV pre-unit parallel-twin engine, produced by the Norton Motorcycle company from 1967 until 1977. Initially having a nominal 750 cc displacement, actually 745 cc (45.5 cu in), in 1973 it became an 850 cc, actually 828 cc (50.5 cu in). It had a hemi-type head, similar to all OHV Norton engines since the early 1920s.

Anzani 10-cylinder

The Anzani 10 was a 1913 10-cylinder air-cooled radial aircraft engine. It powered several experimental aircraft and also the later production versions of the Caudron G.3 reconnaissance aircraft, the Caudron G.4 bomber/trainer and the first production Cessna, the Model AA.

Vincent Rapide

The Vincent Rapide is a line of standard motorcycles designed and built by the Vincent HRD motorcycle company at their works in Great North Road, Stevenage, Hertfordshire, England. The model debuted in 1936 and was built until 1939. Production resumed in 1946 and ended in 1955. Four major versions were built, labelled Series A through D.

Yamaha TX500

The Yamaha TX500 is a two-cylinder standard motorcycle built by Yamaha and sold in 1973 and 1974. Early models closely resembled the Triumph Bonneville in style. In 1975 the bike was renamed XS500 and then continued to be updated until 1978 when sales ended in the USA. In Europe, the model was available through 1980.

Norton Dominator

The Dominator is a twin cylinder motorcycle developed by Norton to compete against the Triumph Speed Twin. The original Dominator was designed in 1947 and 1948 by Bert Hopwood, who had been on the Speed Twin design team at Triumph. Available for sale from mid 1949, this design set the pattern for Norton twins for the next 30 years.

BSA A7 motorcycle

The BSA A7 was a 500cc motorcycle model range made by Birmingham Small Arms Company (BSA) at their factory in Armoury Road, Small Heath, Birmingham. The range was launched in 1946 using a 495 cc (30.2 cu in) long stroke engine. An improved 497 cc (30.3 cu in) version based on the BSA A10 engine was launched in 1950. The various A7 models continued in production with minor modifications until 1961/2 when they were superseded by the unit-construction A50 model.

Triumph Ricardo

The Triumph Ricardo was a British single-cylinder motorcycle manufactured by the Triumph Engineering Co Ltd between 1921 and 1928. Named after engine designer Sir Harry Ricardo it featured an innovative four valve head design and was capable of over 70 mph, set three world speed records and won a gold medal in the 1923 International Six Day Trial.

BSA motorcycles were made by the Birmingham Small Arms Company Limited (BSA), which was a major British industrial combine, a group of businesses manufacturing military and sporting firearms; bicycles; motorcycles; cars; buses and bodies; steel; iron castings; hand, power, and machine tools; coal cleaning and handling plants; sintered metals; and hard chrome process.

BSA A10 series series of motorcycles

The BSA A10 series was a range of 646 cc (39.4 cu in) air-cooled parallel twin motorcycles designed by Bert Hopwood and produced by Birmingham Small Arms Company at Small Heath, Birmingham from 1950 to 1963. The series was succeeded by the A65 unit construction models.

BSA B25 Series of motorcycles made by the Birmingham Small Arms Company

The BSA B25 was a series of 250 cc (15 cu in) unit construction single-cylinder OHV four-stroke motorcycles made by the Birmingham Small Arms Company. Developed from the BSA C15, the machines were produced between 1967 and 1971. The B25 was the fastest British production 250,


  1. 1 2 3 4 5 6 7 8 9 10 11 Wilson, Hugo, The Encyclopedia of the Motorcycle, p.181
  2. 1 2 3 4 5 6 7 8 Davis, Simon, "Triumph's First Twin: Triumph 6/1", p. 1
  3. 1 2 3 4 5 6 7 8 9 10 Brooke, Lindsay, Triumph : A Century of Passion and Power, p.26
  4. 1 2 3 4 5 Brooke, Lindsay, Triumph : A Century of Passion and Power, p.27
  5. 1 2 3 4 5 6 7 8 9 10 11 Brooke, Lindsay, Triumph : A Century of Passion and Power, p.25
  6. 1 2 3 4 5 6 7 8 9 Brooke, Lindsay, Triumph : A Century of Passion and Power, p.24
  7. Brooke, Lindsay, Triumph : A Century of Passion and Power, pp.22, 24
  8. 1 2 3 4 5 6 7 8 9 Davis, Simon, "Triumph's First Twin: Triumph 6/1", p. 2

Further reading