The AN/SQS-504 Diver [1] was an early naval medium-frequency active variable depth sonar [2] (VDS) developed in Canada.
The AN/SQS-504 emerged from a post-Second World War program to improve the detection of submarines between the thermal layers in the Gulf of Saint Lawrence. [3] A transducer derived from a wartime British Type 144 sonar was placed in a towed body [4] and deployed from the stern by the AN/SQA-501 handling gear. [5] The AN/SQS-504 was succeeded by the AN/SQS-505, which used a then-modern transducer and receiver. [6]
It was deployed in the 1960s by the Royal Canadian Navy (RCN), the British Royal Navy (RN), and the Royal Australian Navy. The United States Navy (USN) did not adopt the AN/SQS-504, but the design of the towed body handling gear influenced later USN VDS. [7]
The success of the AN/SQS-504 has led to claims that VDS was invented [8] or primarily developed in Canada. [9]
During the Second World War, the thermal layers in the Gulf of Saint Lawrence severely decreased the detection range of hull-mounted sonar. From 1944 to 1948, Canadian institutions used sonar and bathythermographs to investigate the effect of oceanic and seasonal conditions on underwater sound propagation. After war, the Naval Research Establishment (NRE) conducted sonar ranging trials in the Bay of Fundy and St. Margarets Bay, Nova Scotia with British Type 144 sonar. [10] [4] In December 1948, the NRE reported that in the summer the waters of the Scotian Shelf was divided into three temperature layers, and a sonar lowered into the cold middle layer might have good detection range against submarines within that layer. [11]
In 1949, the RCN issued requirements for a towed sonar for operations in the shallow waters of the Gulf of Saint Lawrence and off Halifax, Nova Scotia. [12] The Defence Research Board of Canada (DRBC) organized a development program for a towed dipping sonar in April 1949. Early trials were conducted using an experimental dipping sonar called "Hot Dog", a harbour defence sonar capsule lowered over the side or rear of a stationary ship by electrical cable. The trials confirmed the possibility of achieving long detection ranges and the reduced efficacy of hull-mounted sonar against targets in the middle layer. The RCN requested top priority for the project in October 1952, and the development effort became "Project DUNKER". [13] RCN requirements were revised in 1954; it now called for a sonar that could be deployed at variable depths, and so would be useful in wider range of conditions. [14]
The next step was the development of a towing body and faired cables suitable for operational use on RCN warships at a speed of 15 to 20 knots (28 to 37 km/h; 17 to 23 mph). The first experimental towing body, "Toby", was torpedo-shaped; after being lost it was replaced by "Toby II", which incorporated an aluminium nose with a fixed Type 144. A Winged Housed Air Towed Sonar (WHATS), developed by the EDO Corporation for blimp-towed sonars, was also adapted for experiments. NRE designed the "Canadian Body" (Canby) and contracted the Fairey Aviation Company to build it; Canby was trialled in October 1953. [12]
Ultimately, the towing body that was adapted for service was the "Trilby". Trilby was based on a RN 100-inch (250 cm) sonar dome [12] and developed in close cooperation with the David Taylor Model Basin (DTMB) in the United States; [4] its shape was radically different than Canby, allowing it to house a larger transducer that could also be trained all around. Trilby was first trialled in 1955. [12] The after ends of the tails fins were sharpened "knife sharpness" to eliminate tail flutter which jammed the sonar receiver. [15]
The development of cable fairing was required to solve serious tow-off problems. Trials only began in spring 1952 after delays caused by Cold War and Korean War rearmament. The tow-off problem was solved in early 1953 by completely redesigning the fairing [12] with the help of DTMB. [4] Over-the-stern towing was found to be superior to over-the-side towing—the latter was then being pursued by the USN. [12]
NRE developed a new "searchlight" sonar called "Canadian ASDIC Search Towed 1" (CAST/1), [4] [12] using the Type 144 as a starting point. [4] The transducer used a high-activity low-impedance piezoelectric ceramic developed by NRE; the ceramic, called NRE-4, was barium titanate with small quantities of cobalt. [16] NRE-4 allowed transmission power 300-times greater [4] than the steel-quartz transducer in the Type 144. [16] British and American ceramics were not available due to industrial supply issues. Initially, the connecting cable's electrical conductors burned failed after a few hours of use; this was resolved by adopting design and testing procedures for such cables from the Department of Mines in Ontario. [4] CAST/1 also had a split beam direction finding system. [12]
Development of the AN/SQA-501 handling gear occurred from the early 1950s to 1960. Early development used parts salvaged from DRBC experiments and naval stocks. During one trial, the cable release clutch failed to function when the cable or body became caught underwater; the cable pulled itself off the drum and destroyed the gearbox. The clutch was upgraded to release under higher strain. The parallel mechanism was also redesigned to prevent jamming during a recovery operation. [17]
CAST/1 was placed into the towed body to create the "Canadian ASDIC Search Towed research 1" (CAST/1/R) VDS. [4] [12] CAST/1/R was successfully tested in the Bermuda area in December 1955. [12]
A related development was the "Canadian ASDIC Search Towed experimental 1" (CAST/1/X) VDS; [4] [12] CAST/1/X used modified Canby handling gear, and an experimental version of CAST/1 that operated on a "train-ping-listen" sequence. CAST/1/X was completed and installed on HMCS Crusader in June 1956. It conducted successful submarine target trials in September and November that same year. [12] CAST/1/X out-ranged the Type 144 used by the RCN by a factor of five. [18]
In 1958, the CAST/1/X, aboard Crusader, performed comparative tests with the British experimental Type 192x VDS, aboard HMS Brocklesby. The CAST/1/X performed similarly to the much larger Type 192x. The British subsequently abandoned the Type 192x and adopted the Canadian system as the Type 199. [7]
CAST/1/X was re-engineered to meet naval standards to become the AN/SQS-504. [5]
Deficiencies in the AN/SQA-501 handling gear, which made operating the AN/SQS-504 difficult to impossible, became apparent within a few years of entering service. Problems included poorly designed hydraulics, damage to the AN/SQS-504 because it was slightly too wide to fit between the saddle arms, and an overall haphazard design. [19] In 1964, the RCN formed a small team that worked to fix the AN/SQA-501, although time and material were not formally allocated. [19] This followed a hoist failure on HMCS St. Laurent which prevented the recovery of the AN/SQS-504 for 18 hours during JETEX 64. [20]
A further difficulty was the range of RCN anti-submarine (ASW) weapons. The AN/SQS-504 had a range of 5,000 to 7,000 yards (4,600 to 6,400 m), but upon entering service the RCN was equipped with the much shorter-ranged Limbo mortar and Mark 43 torpedo. [21]
Even as the AN/SQS-504 entered service, the RCN was already looking for longer-ranged sonar to vector ASW helicopters against faster and deeper diving Soviet nuclear submarines. In 1960, the RCN initiated Project DIANA ONE which ultimately resulted in the AN/SQS-505 hull and VDS sonar and the AN/SQA-502 handling gear. [22] [23]
The British Type 199 is an AN/SQS-504 with RN rigging. [24]
Only HMAS Stuart and Derwent were fitted. The sonar was unsuccessful in Australian service and later removed. [25]
Sonar is a technique that uses sound propagation to navigate, measure distances (ranging), communicate with or detect objects on or under the surface of the water, such as other vessels. Two types of technology share the name "sonar": passive sonar is essentially listening for the sound made by vessels; active sonar is emitting pulses of sounds and listening for echoes. Sonar may be used as a means of acoustic location and of measurement of the echo characteristics of "targets" in the water. Acoustic location in air was used before the introduction of radar. Sonar may also be used for robot navigation, and SODAR is used for atmospheric investigations. The term sonar is also used for the equipment used to generate and receive the sound. The acoustic frequencies used in sonar systems vary from very low (infrasonic) to extremely high (ultrasonic). The study of underwater sound is known as underwater acoustics or hydroacoustics.
The Fleet Rehabilitation and Modernization (FRAM) program of the United States Navy extended the lives of World War II-era destroyers by shifting their mission from a surface attack role to that of a submarine hunter. The FRAM program also covered cruisers, aircraft carriers, submarines, amphibious ships, and auxiliaries. The United States Coast Guard also used this term in the 1980s for the modernization of its Hamilton-class cutters.
The 46 Knox-class frigates were the largest, last, and most numerous of the US Navy's second-generation anti-submarine warfare (ASW) escorts. Originally laid down as ocean escorts, they were all redesignated as frigates on 30 June 1975, in the 1975 ship reclassification plan and their hull designation changed from 'DE' to 'FF'. The Knox class was the Navy's last destroyer-type design with a steam turbine powerplant.
HMS Penelope was a Leander-class frigate of the Royal Navy. In the Falklands War, Penelope fired on an Argentine patrol boat and claimed to be the last ship attacked by Argentine aircraft over the course of the war. In 1991, she was commissioned into the Ecuadorean Navy, and renamed Presidente Eloy Alfaro.
The Sikorsky CH-124 Sea King is a twin-engined anti-submarine warfare (ASW) helicopter designed for shipboard use by Canadian naval forces, based on the US Navy's SH-3. It served with the Royal Canadian Navy (RCN) and Canadian Armed Forces from 1963 to 2018.
HMCS Yukon was a Mackenzie-class destroyer that served in the Royal Canadian Navy (RCN) and later the Canadian Forces. She was the first Canadian naval unit to carry the name. She was named for the Yukon River that runs from British Columbia through Yukon and into Alaska in the United States.
HMCS Nipigon was an Annapolis-class destroyer that served in the Royal Canadian Navy and later the Canadian Forces. She was the second Canadian naval unit to carry this name. Entering service in 1964, she was named for the Nipigon River that flows through Ontario.
The AN/SQQ-32 minehunting sonar set (MSS) is a variable-depth mine-hunting sonar system originally developed by Raytheon and Thales Underwater Systems for the United States Navy. It includes two separate active sonar systems to detect and classify mine-like objects on the surface, in the volume, or on the bottom of the sea. The sonar systems are packaged in a single towed body tethered to the ship through a cable providing power and data transmission, with the cable length variable via an electric winch. A hole in the ship extending from the sonar maintenance room (SMR) to the hull allows movement of the towed body in different configurations for maintenance, stowage at sea, and minehunting operations. The towed body can be configured for minehunting by either locking to the bottom of the ship's hull for shallow water operations, or by extending and retracting the tow cable to allow for variable depth sonar (VDS) operations. VDS operations are necessary in deep water due to refraction of the sonar from the various temperature layers present in the ocean; with the sonar positioned in the same thermal layer as the suspected mines the error induced by refraction is minimized. The detect and classify sonar subsystems are independently monitored and controlled by two operators at independent panels working together to find and characterize underwater objects as mine or non-mine like objects.
The St. Laurent-class destroyer was a class of destroyer escorts that served the Royal Canadian Navy and later the Canadian Forces from the mid-1950s to the mid-1990s.
The People's Liberation Army Navy (PLAN) is the naval branch of the People's Liberation Army (PLA), the armed forces of the People's Republic of China. The PLAN force consists of approximately 250,000 men and over a hundred major combat vessels, organized into three fleets: the North Sea Fleet, the East Sea Fleet, and the South Sea Fleet.
HMCS Annapolis was an Annapolis-class destroyer that served in the Royal Canadian Navy and later, the Canadian Forces. She was the second Canadian naval unit to carry this name. Named for the Annapolis River that flows through Nova Scotia, the ship entered service in 1964, the last of the St. Laurent-class design. Serving through the Cold War, Annapolis was decommissioned in 1998 before going through a protracted legal battle for use as an artificial reef. She was finally scuttled as such in 2015 off the coast of British Columbia.
HMCS Mackenzie was a Mackenzie-class destroyer that served in the Royal Canadian Navy (RCN) and later the Canadian Forces. She was the lead ship of her class and is the first Canadian naval unit to carry this name. The ship was named for the Mackenzie River, the largest river system in Canada and runs primarily through the Northwest Territories.
HMCS Qu'Appelle was a Mackenzie-class destroyer that served in the Royal Canadian Navy and later the Canadian Forces. The ship's insignia and logo was the head of a fox facing forward centered in a diagonal line double white with a red center sqiggley line from the top left to bottom right. The moniker of the ship was "Follow the Fox".
HMCS Kootenay was a Restigouche-class destroyer escort that served in the Royal Canadian Navy and Canadian Forces from 1959 until 1996. She was the fifth ship in her class and the second vessel to carry the designation HMCS Kootenay. The ship suffered two serious incidents in her career: a 1969 explosion and ensuing fire that killed nine, and a 1989 collision that required the complete replacement of her bow. Following her service, the ship was sunk as an artificial reef.
HMCS Ottawa was a St. Laurent-class destroyer that served in the Royal Canadian Navy and later the Canadian Forces from 1956 to 1992. Ottawa was the first bilingual ship to serve in the Canadian navy.
HMCS Saskatchewan was a Mackenzie-class destroyer that served in the Royal Canadian Navy (RCN) and later the Canadian Forces. She was the second Canadian naval unit to bear the name HMCS Saskatchewan. The ship was named for the Saskatchewan River which runs from Saskatchewan to Manitoba in Canada.
The Annapolis-class destroyer escort was a two-ship class of destroyer escorts that saw service with the Royal Canadian Navy and Canadian Forces from the 1960s to the 1990s. The final version of the St. Laurent-class design, the class was used extensively for anti-submarine warfare purposes. Both ships were sunk as artificial reefs after being retired, one on each coast of Canada.
HMCS St. Laurent was a St. Laurent-class destroyer that served in the Royal Canadian Navy and later the Canadian Forces from 1955–1974. She was the lead ship of her class, the first modern warship designed and built in Canada.
HMCS Gatineau was a Restigouche-class destroyer that served in the Royal Canadian Navy and later the Canadian Forces during the Cold War from 1959 to 1996. She was the third ship in her class and the second vessel to carry the designation HMCS Gatineau. She was sold for scrapping in 2009.
The Dealey-class destroyer escorts were the first post-World War II escort ships built for the United States Navy.