Bridge (dentistry)

Last updated
Bridge (dentistry)
ICD-9-CM 23.42-23.43
MeSH D003829
A three unit porcelain fused to metal bridge (PFM) made by a dental technician. Bridge from dental porcelain.jpg
A three unit porcelain fused to metal bridge (PFM) made by a dental technician.
A semi-precision attachment between teeth #3 and #4, with the mortise on #4. Note the lingual buttons extending, in the photo, upward on #2 (on the left) and downward on #4. These are used to grasp the crowns with a hemostat and make them easier to handle. They can also be used to aid in removal of the crown in case there is an excessive amount of retention during the try-in. They are cut off prior to final cementation. Semi-precision attachment.jpg
A semi-precision attachment between teeth #3 and #4, with the mortise on #4. Note the lingual buttons extending, in the photo, upward on #2 (on the left) and downward on #4. These are used to grasp the crowns with a hemostat and make them easier to handle. They can also be used to aid in removal of the crown in case there is an excessive amount of retention during the try-in. They are cut off prior to final cementation.
The proximal surfaces of the pre-solder index abutment and pontic, showing lab-processed grooves for added retention of the acrylic resin Pre-solder index.jpg
The proximal surfaces of the pre-solder index abutment and pontic, showing lab-processed grooves for added retention of the acrylic resin
The abutment and pontic joined with acrylic resin in a solder index and reinforced with an old bur (lying horizontally across the occlusal surface of the copings). Post-solder index.jpg
The abutment and pontic joined with acrylic resin in a solder index and reinforced with an old bur (lying horizontally across the occlusal surface of the copings).

A bridge is a fixed dental restoration (a fixed dental prosthesis) used to replace one or more missing teeth by joining an artificial tooth definitively to adjacent teeth or dental implants.

Contents

Definitions

Fixed bridge: A dental prosthesis that is definitively attached to natural teeth and replaces missing teeth. [1]

Abutment : The tooth that supports and retains a dental prosthesis. [2]

Pontic: The artificial tooth that replaces a missing natural tooth. [2]

Retainer : The component attached to the abutment for retention of the prosthesis. Retainers can be major or minor. [3]

Unit: Pontics and abutment teeth are referred to as units. The total number of units in a bridge is equal to the number of pontics plus the number of abutment teeth. [1]

Saddle: The area on the alveolar ridge which is edentulous where at least one missing tooth is to be reinstated. [3]

Connector: Joins the pontic to the retainer or two retainers together. Connectors may be fixed or movable. [3]

Span: The length of the alveolar ridge between the natural teeth where the bridge will be placed. [3]

Resin-bonded bridge: A dental prostheses where the pontic is connected to the surface of natural teeth which are either unprepared or minimally prepared. [4]

Advantages and disadvantages of tooth replacement

AdvantagesDisadvantages
Restore aesthetics (particularly important for anterior edentulous areas)Loss of tooth tissue (tooth preparation of abutments often requires significant tooth preparation)
Restore function (mastication, speech)Pulpal damage (tooth preparation opens dentinal tubules providing a connection between bacteria in the mouth and the pulp. Deep preparations can cause pulpal injury)
Occlusal stability (prevent tilting, drifting, rotation and over-eruption of adjacent/opposing teeth)Secondary caries (around crown margins, under debonded retainer wings)
Patient preference

[3]

Types of bridge

Conventional bridge

High translucent zirconium fixed-fixed bridge built with VM9 vita porcelain and stained with luster paste. The upper first premolar is considered the pontic and the teeth prepared are abutments. Zirconia bridge.jpg
High translucent zirconium fixed–fixed bridge built with VM9 vita porcelain and stained with luster paste. The upper first premolar is considered the pontic and the teeth prepared are abutments.

Conventional bridges are bridges that are supported by full-coverage crowns, three-quarter crowns, post-retained crowns, onlays and inlays on the abutment teeth. In these types of bridges, the abutment teeth require preparation and reduction to support the prosthesis. Conventional bridges are named depending on the way the pontic (false teeth) is attached to the retainer. [5]

Fixed–fixed bridges

A fixed–fixed bridge refers to a pontic which is attached to a retainer at both sides of the space with only one path of insertion. This type of design has a rigid connector at each end which connects the abutment to the pontic. As the abutments are connected together rigidly, it is critical that during tooth preparation the proximal surfaces of the abutment teeth must be prepared so that they are parallel to each other. [3]

Cantilever

A cantilever is a bridge where a pontic is attached to a retainer only at one side. The abutment tooth may be mesial or distal to the pontic. [3]

In a spring cantilever, the pontic and retainer are remote from each other and connected by a metal bar. Usually, a missing anterior tooth is replaced and supported by a posterior tooth. This design of bridge has been superseded. [3]

Fixed–movable

The pontic is firmly attached to a retainer at one end of the span (major retainer) and attached via a movable joint at the other end (minor retainer).

A major advantage of this type of bridge is that the movable joint can accommodate the angulation differences in the abutment teeth in long axis, which enables the path of insertion to be irrespective of the alignment of the abutment tooth. [5] This enables a more conservative approach as the abutments do not need to be prepared to be parallel to one another. Ideally the rigid connector should attach the pontic to the more distal abutment. The movable connector attaches the pontic to the mesial abutment, enabling this abutment tooth limited movement in a vertical direction. [3]

Resin-bonded bridge

An alternative to the traditional bridge is the resin-bonded or adhesive bridge (also called a Maryland bridge). An resin-bonded bridge utilises retainer "wings" on the sides of the pontic which attach it to the etched enamel of the abutment teeth. Abutment teeth require minor or no preparation. They are most often used when the abutment teeth are whole and sound (i.e., no crowns or major fillings). [4] Single retainer cantilever resin-bonded bridges have less complications than end-to-end resin-bonded bridges with retainer wings on both sides. [4]

Combination designs

The incorporation of elements of different conventional bridge designs. A popular combination design is the use of a fixed-fixed design with a cantilever. [3]

Hybrid designs

Bridges that incorporate elements of both conventional and adhesive bridge designs. [3]

Advantages and disadvantages of conventional bridge designs

AdvantagesDisadvantages
Fixed–fixed
  1. Maximum strength
  2. Very retentive
  3. Most accepted design for longer spans
  4. Construction is relatively straightforward
  1. Preparations must be parallel which may require extensive tooth preparation. Weakens the tooth and risks damaging the pulp.
  2. Achieving parallel preparations is challenging. It is important to avoid undercuts.
  3. Abutments are major retainers requiring extensive preparation
  4. Cemented as one unit which may be challenging
Fixed-movable
  1. Non-parallel abutments may be used which avoids extensive tooth preparation
  2. Minor retainers are used so the preparations are more conservative of tooth tissue
  3. Enables small movements of teeth
  4. Cementation is more straightforward as components can be cemented separately
  1. Not appropriate for long spans
  2. Complex design for the laboratory to construct
  3. Temporary bridge is complex to make
Cantilever
  1. Only one abutment is required therefore conservative
  2. Destructive parallel preparations not required
  3. Most appropriate design when replacing anteriors
  4. Maintenance and oral hygiene is easier for the patient
  1. Span length limited to one pontic due to leverage on the abutment
  2. Rigid design to prevent distortion
  3. Tilting of abutment teeth due to occlusal forces

[3]

Advantages and disadvantages of resin-bonded bridge designs

AdvantagesDisadvantages
Fixed-fixed
  1. Large surface area providing good retention
  2. Simple to construct in the laboratory
  1. Debonding which can allow secondary caries to develop under the failed wing
  2. Tilted abutments may require extensive preparation to achieve parallelism and sufficient retention
  3. Ideally abutments should be equally retentive which is difficult to achieve, especially posteriorly when the retainers are a molar and premolar
Fixed-movable
  1. Abutment teeth are able to move independently
  2. The retention of the two retainers does not need to be equal
  3. Minor retainer can be minimally retentive
  4. Stops tilting of the posterior abutment
  1. Design not advised for anterior bridges
  2. Design not appropriate for long spans
  3. More complex to construct in the laboratory
Cantilever
  1. Most conservative of tooth tissue as minimal (if any) preparation required on one abutment only.
  2. Design of choice for replacing single anteriors
  3. Can be used for short posterior spans
  4. Straightforward to construct in the laboratory
  5. Patients are able to maintain good oral hygiene as it is easy to clean
  1. Limited retention due to small surface area
  2. Risk of debonding due to torquing forces
  3. Appropriate positioning on cementation may be complex

[3]

Case selection and treatment planning

Case selection

Appropriate case selection is important when considering the provision of fixed bridgework. Patient expectations should be discussed and a thorough patient history should be obtained. Replacement of missing teeth with fixed bridgework may not always be indicated and both patient factors alongside restorative factors should be considered before deciding if providing fixed bridgework is appropriate. [6] The survival rate of bridgework can be affected by the span of bridge needed, the proposed position of the bridge, and the size, shape, number and condition of planned abutment teeth. [7] Furthermore, any active disease including caries or periodontal disease should be treated and followed by a period of maintenance to ensure patient compliance in maintaining appropriate oral hygiene. [8] [9]

Study models mounted on a semi-adjustable articulator using a facebow record are a useful aid to study occlusion prior to provision of a fixed prosthesis. They may also be used to practice planned tooth preparation. Subsequently, a diagnostic wax-up can be provided to help the patient visualise the final prosthesis and to construct a silicone index. This index can be used to make a temporary prosthesis. [3] [10]

Selection and evaluation of abutment teeth

Multiple factors influence the selection of appropriate abutment teeth. These include the size of potential abutment tooth, with larger teeth having an increased surface area preferable for retention, using teeth with a stable periodontal status, favourable tooth angulation, favourable tooth position, and an adequate crown–root ratio. [1] [11]

Careful abutment selection is critical for the success of bridgework. The prosthesis must be capable of tolerating occlusal forces, which would normally be received by the missing tooth as well as its normal occlusal loading. These forces are transmitted to the abutment(s) via the prosthesis. [3]

Vital teeth are preferred to endodontically treated ones for bridge abutments. Endodontically treated teeth have lost a large amount of tooth structure, weakening them and making them less able to tolerate additional occlusal loading. Post crowns have been shown in some studies to have a higher failure rate. [3]

For resin bonded bridges abutment teeth should ideally be unrestored and have enough enamel to support the metal wing retainer. Additionally there must be sufficient space to accommodate the minimum connector width of 0.7mm and 2mm connector height. It is acceptable for the abutment to be minimally restored with small composite restorations provided they are sound. It is advised to replace old composite restorations prior to cementation to provide optimum bond strength via the oxide layer. [4]

Teeth with active disease such as caries or periodontal disease should not be used as abutments until the disease has been stabilised. Once stable periodontally compromised teeth may be used as abutments, depending on the crown to root ratio described below. [3]

Ante's law states that the roots of abutment teeth must have a combined periodontal surface area in three dimensions that is more than that of the missing root structures of the teeth replaced with a bridge, is used in bridgework design. This law remains controversial in terms of supporting clinical evidence. [4]

Crown to root ratio is the distance from the occlusal/incisal surface of the tooth to the alveolar crest in relation to the length of root within the bone. The minimum ratio of crown to root is considered to be 1:1, although the most favourable is a crown:root of 2:3. As the proportion of tooth supported by bone decreases, the lever effect increases. [3] [4]

Root configuration should be considered when selecting abutment(s). Divergent roots of posteriors provide increased support compared to converging, fused or conical roots. Roots that curve apically provide increased support compared to those which have a fixed taper. [4]

The number of abutments required depends on both the position of the tooth to be replaced and the length of the span. Cantilever designs utilising one abutment is the design of choice for replacing a single tooth anteriorly and can also be used posteriorly. [3]

Occlusion of the pontic with the opposing tooth should be assessed. This may determine which type of design is most appropriate and therefore how many abutments are required. [3] For resin bonded bridges the pontic should have light contact in intercuspal position (ICP) and no contact in lateral excursions. [4] [10]

Biomechanical considerations

Torquing forces can occur when the pontic lies outside the interabutment axis line as the pontic acts as a lever arm. This is particularly applicable to long span bridges replacing multiple anteriors. [4]

Deflection varies directly with the cube of the length, and inversely with the cube of the occlusogingival thickness of the pontic. The longer the span, the more deflection occurs. The amount of deflection is 8 times greater when the length of the span increases to 2 pontics, and increases to 27 times greater with 3 pontics in comparison to a single pontic. It is likely that increased span length will result in the abutments being subjected to increased torquing forces. The thinner the pontic, the more deflection occurs. If the thickness of the pontic is reduced by 50% this causes an 8 times increase in deflection. Choosing pontics with increased occlusogingival dimension and using high yield strength alloys to construct the prosthesis will help reduce deflection. [4]

Indications for use

  1. Replacement of a single tooth or a small spanning space.
  2. Good oral health status and motivation of patient to maintain oral health. [10]
  3. Periodontal status of remaining dentition at a stable and satisfactory level. [10]
  4. Abutment teeth of good quality with minimal restorations and enough surface area and enamel present for adhesion. [11]
  5. Splinting of periodontally compromised teeth to improve occlusal stability, comfort and decrease mobility. (Periodontally compromised teeth is also a contraindication). [11]
  6. As a way of fixed retention after orthodontic treatment or extraction. [11]
  7. Patient unsuitable for implants. This may be due to inadequate bone levels, expense or patient not wanting to receive implants. [11]

Contraindications

  1. Size of saddle area too long. [12]
  2. Patients with parafunction e.g. bruxism. [12]
  3. Tooth mobility increases risk of de-bonding. [11]
  4. Malaligned teeth resulting in poor aesthetics and common path of insertion. [11]
  5. Abutment tooth quality inadequate for example may have a reduced surface area, reduced enamel or be heavily restored. [11]
  6. Increased risk of caries due to increased difficulty in maintaining oral hygiene around the bridgework. [11]
  7. Increased risk of loss of vitality.
  8. Allergy to base metal alloys e.g. nickel [11]
  9. Poor patient motivation. Active dental disease (caries, periodontal disease) and poor oral hygiene. [4]

Types of artificial plastic teeth

Types of artificial plastic teeth (known in the industry as Pontics)

  1. Wash-through Pontic [13] (also known as hygienic pontic or sanitary pontic) [3]
  2. Dome Pontic (also known as bullet- or torpedo-shaped) [13]
  3. Ridge Lap Pontic (also known as Full Saddle Pontic) [13]
  4. Modified Ridge-Lap Pontic [13]
  5. Ovate Pontic [13]

A pontic aims to restore aesthetics, give occlusal stability and improve function. [3]

The hygienic pontic does not contact the underlying alveolar ridge, making it the most straightforward to keep clean. Due to the poor aesthetics of this design it is most commonly employed to replace mandibular molars. [3]

The bullet pontic is the second most favourable in terms of being able to maintain good oral hygiene, with the pontic only contacting one point of the alveolar ridge. [3]

Ridge lap and modified ridge lap pontics have superior aesthetics to the designs discussed previously, with the labial/buccal surface aiming to restore the appearance of a natural tooth from the incisal edge to the gingival margin. To minimise coverage of the soft tissues the lingual/palatal portion of the pontic is reduced to improve accessibility for maintaining good oral hygiene. For the modified ridge lap design the pontic only contacts the buccal aspect of the alveolar ridge. [3]

The ovate pontic comes into contact with the underlying soft tissue and hides the defects of the edentulous ridge with applying light pressure. [14] It is commonly used in provisional bridges following extraction of teeth to improve the emergence profile and helps in shaping the gingiva around the future fixed prosthesis. [15]

Types of bridges according to durability

Bridges can either be provisional (temporary/interim) or permanent. The provisional bridge is a transitional restoration that protects the teeth that are weakened by the preparation, and stabilises the dental tissues until the fabrication of the final restoration, moreover, it can pave the way to the aesthetics of the future permanent restoration and its appearance, which can help the patient accept the final profile. [16] Provisional restorations are designed to be used for a few weeks to months, they can be fabricated directly (by chair side), or indirectly ( in the dental laboratory). It is usually tried in a few times to check if it fits properly and if its margins are well adapting on the teeth surface and gingiva, it may need relining or a few adjustments. [17] Provisional bridges can either be made of acrylic resins or metal. The resins are the most commonly used, they are either made of cellulose acetate, polycarbonate or poly-methyl methacrylate. Other chemically activated resins include poly-R methacrylates: these are methacrylates with ethyl or isobutyl substances added to increase the strength of material. Also, commonly used resins include the BisGMA based dimethacrylate, and the visible light urethane di-methylacrylate. [17] [18] Dimethacrylate-based materials were found to be better than monomethacrylates for temporary restorations in terms of flexural strength and hardness. [19] [20]

Types of bridges according to material

  1. Metal based, noble based metals such as gold, or base metal alloys such as nickel chromium.
  2. Non-metal based. They can be either resin veneered, fibre-reinforced composite, porcelain fused to metal, or ceramics which are either silica, alumina, or zirconia. [16]

Acrylic resin and porcelain fused to metal (PFM)

Unaesthetic display of metal in a porcelain fused to metal restoration Metal display in a PFM crown.jpg
Unaesthetic display of metal in a porcelain fused to metal restoration

Acrylic resin was the first veneering material used to help restore the aesthetics of crown and bridges. The aim was to maintain a similar colour to natural teeth by attaching it on the labial surface of metal crown / bridges; however, resin-veneered dental prosthetics lacked stability and abrasion resistance. [16] Porcelain fused to metal (PFM) was then introduced; the porcelain is composed of two layers (one opaque to cover the metal substructure and another translucent to provide an enamel illusion). Still several researchers consider PFM the gold standard as it has been reported to have 95% success over a 10-year period, a reason why newer types of all-ceramic restorations are usually compared to PFM crowns/bridges to assess its success and durability. [21] However, PFM restorations may show a grey colour at the cervical margins of the tooth showing the metal substructure.

IPs Emax

IPs Emax ceramics offer high aesthetic properties, which is why its use has been increasingly popular. However, there is insufficient evidence to determine the longevity of Emax in bridges; some reports have found fair short-term survival, but unfavorable medium-term survival. [22] Failures of restorations were most reported in the posterior teeth region. IPs Emax is available as press ingots or as IPs Emax CAD/CAM system. [23] Emax use in crowns or bridges is not recommended for patients who suffer from bruxism. [24]

Zirconia

Zirconia is used in anterior, and posterior fixed bridges, and also on implants. Zirconia is fabricated using the dental CAD/CAM technology. [25] It has high mechanical strength and it can withstand high occlusal forces compared to all-ceramic materials. [26] in addition it can resist crack propagation in the core material; however, cracks often occur in the veneering material leading to its fracture whether in the tooth-supported or implant-supported bridges. [27] [28] Reports found that the 3×3 mm designed connectors in zirconia bridges increased the strength to resist fracture by 20%. [29] [30]

Although the use of ceramic based fixed prosthesis have been popular as it achieves a lifelike, highly esthetic appearance, a Cochrane Review found insufficient evidence to support or refute the effectiveness of ceramic materials for fixed prosthodontic treatment over metal-ceramic. [31]

Clinical stages of bridgework

  1. Assessment: Clinical assessment of the patient's suitability for bridgework. Detailed history (including medical history), appropriate assessment of the suitability of the patient's oral environment (including occlusion, caries risk, periodontal risk, radiographic examination, sensibility testing), assessment of patient aims and motivation, abutment tooth selection and bridge design. [3] [10]
  2. Primary impressions: Primary impressions can be taken with alginate to make study casts. A facebow record should also be taken to enable the occlusion to be studied prior to provision of the prosthesis [4] [10]
  3. Diagnostic wax-up: This enables the patient to visualise how the definitive prosthesis will look. The wax up can also be used to construct a putty matrix which can be used subsequently to make a temporary restoration. [3] [4] [10]
  4. Restoration replacement: Restorations in abutment teeth with questionable prognosis or old composite resin restorations for adhesive bridgework should be replaced. [4]
  5. Tooth preparation: This should be completed with reference to radiographs and study casts obtained during treatment planning. For conventional bridges, tooth preparation should aim to conserve tooth tissue, ensure a parallel path of insertion, achieve clearance in the occlusion and ensure well defined preparation margins. [10] The taper of each preparation on the abutment teeth must be the same. This is known as parallelism among the abutments and allows the bridge to fit onto the abutment teeth. Adhesive bridges require minimal preparation.
  6. Master impressions: An accurate impression should be made of the prepared teeth, along with an impression of the opposing arch. The master casts are used to provide accurate information about the occlusion to the laboratory and construct the prosthesis. [10]
  7. Occlusal registration: An occlusal registration is needed when providing extensive bridgework to allow the opposing casts to be related accurately. This may not be necessary if only a small number of teeth are to be restored. [10]
  8. Temporary restoration: Temporary restorations should be fabricated if possible to protect and maintain the prepared teeth until placement of the final restoration. [10]
  9. Try in: Confirm the clinical acceptability before cementing definitively. Assess the prosthesis on the master casts and identify the cause of any problems if present. A period of temporary cementation to assess clinical acceptability prior to definitive placement is sometimes used. [10]
  10. Final placement: Once satisfied the prosthesis is clinically acceptable, cement and bond the bridgework definitively. [10]
  11. Review: Assess the bridgework and manage any post-operative issues. [10]

Restoration fabrication

Full dental bridge being machined using WorkNC Dental CAD/CAM software. WorkNC-dental bridge.jpg
Full dental bridge being machined using WorkNC Dental CAD/CAM software.

As with single-unit crowns, bridges may be fabricated using the lost-wax technique if the restoration is to be either a multiple-unit FGC or PFM. Another fabrication technique is to use CAD/CAM software to machine the bridge. [32] As mentioned above, there are special considerations when preparing for a multiple-unit restoration in that the relationship between the two or more abutments must be maintained in the restoration. That is, there must be proper parallelism for the bridge to seat properly on the margins.

Sometimes, the bridge does not seat, but the dentist is unsure whether it is because the spatial relationship between the abutments is incorrect, or whether the abutments do not actually fit the preparations. The only way to determine this is to section the bridge and try in each abutment by itself. If they each fit individually, the spatial relationship was incorrect, and the abutment that was sectioned from the pontic must now be reattached to the pontic according to the newly confirmed spatial relationship. This is accomplished with a solder index.

The proximal surfaces of the sectioned units (that is, the adjacent surfaces of the metal at the cut) are roughened and the relationship is preserved with a material that will hold on to both sides, such as PATTERN RESIN from the company GC America. [33] With the two bridge abutments individually seated on their prepared abutment teeth, the resin is applied to the location of the sectioning to reestablish a proper spatial relationship between the two pieces. This can then be sent to the lab where the two pieces will be soldered and returned for another try-in or final cementation.

Advantages of bridges

Dental bridges offer several advantages.

They can usually be completed in only two dental appointments, restore the tooth back to full chewing function, require no periodic removal for cleaning, have a long life-expectancy and are aesthetically pleasing. [34]

Bridge failures

Common reasons for bridge failures

  1. Poor oral hygiene: As with any fixed prosthesis including bridges, maintaining good oral hygiene to prevent plaque formation around the bridge is key. This will ensure prolonged performance. A study examined the gingival health around the fixed bridges after 14 days – 6 months post insertion found the surfaces were more plaque retentive, causing gingival inflammation regardless the material of fabrication of the bridge, unlike single crowns which did not show the same effect. [35] [36]
  2. Mechanical failures: These failures can occur due to loss of retention of the bridge due to improper cementation, construction or preparation. [37] [38]

Fracture of the metal coating or pontic can also lead to mechanical failures. Fracture in connectors of bridges at the gingival side is a common finding in most all-ceram bridges. [39]

  1. Biological failures: These can occur due to caries in the tooth (one of the commonest causes of crown and bridge failures [9] ) or due to pulpal injury. Problems with abutment teeth such as tooth fracture, secondary caries or periodontal disease can cause discomfort and put pressure on surrounding soft tissues to also cause a biological failure of the bridge.
  2. Aesthetic failures: These can occur at the time of cementation and include; colour mismatch, roughness of margins or improper tooth contour.

Aesthetics failures can also occur over a period of time including through wear of teeth, gingival recession or drifting of teeth.

  1. Problems with abutment teeth: Abutment teeth affected by secondary caries, vitality loss or periodontal disease can all lead to bridge failure. [37]

Oral manifestations of bridge failures

Bridge failures result in clinical complications and patients can present with:

  1. Pain in the oral cavity
  2. Sensitivity, bleeding and inflammation of the gums [37]
  3. Foul breath and taste disturbances

Bridge failure management

Management of bridge failures depends upon the extent and type of failure and these can be prevented through forming a thorough treatment plan with the patient as well regularly emphasising the importance of maintaining a very good level of oral hygiene after the bridge has been placed. The importance of cleaning underneath the pontic, through the use of interdental cleaning aids, should also be reinforced as plaque control around fixed restorations is more difficult. [9]

Management options include:

  1. Keeping the bridge under observation/review
  2. Repairing, replacing or removing the fault [9]

See also

Related Research Articles

Cosmetic dentistry is generally used to refer to any dental work that improves the appearance of teeth, gums and/or bite. It primarily focuses on improvement in dental aesthetics in color, position, shape, size, alignment and overall smile appearance. Many dentists refer to themselves as "cosmetic dentists" regardless of their specific education, specialty, training, and experience in this field. This has been considered unethical with a predominant objective of marketing to patients. The American Dental Association does not recognize cosmetic dentistry as a formal specialty area of dentistry. However, there are still dentists that promote themselves as cosmetic dentists.

Dental restoration, dental fillings, or simply fillings are treatments used to restore the function, integrity, and morphology of missing tooth structure resulting from caries or external trauma as well as to the replacement of such structure supported by dental implants. They are of two broad types—direct and indirect—and are further classified by location and size. A root canal filling, for example, is a restorative technique used to fill the space where the dental pulp normally resides.

<span class="mw-page-title-main">Dental technician</span> Technician working on dental appliances

A dental technician is a member of the dental team who, upon prescription from a dental clinician, constructs custom-made restorative and dental appliances.

<span class="mw-page-title-main">Dental implant</span> Surgical component that interfaces with the bone of the jaw

A dental implant is a prosthesis that interfaces with the bone of the jaw or skull to support a dental prosthesis such as a crown, bridge, denture, or facial prosthesis or to act as an orthodontic anchor. The basis for modern dental implants is a biological process called osseointegration, in which materials such as titanium or zirconia form an intimate bond to the bone. The implant fixture is first placed so that it is likely to osseointegrate, then a dental prosthetic is added. A variable amount of healing time is required for osseointegration before either the dental prosthetic is attached to the implant or an abutment is placed which will hold a dental prosthetic or crown.

<span class="mw-page-title-main">Crown (dental restoration)</span> Dental prosthetic that recreates the visible portion of a tooth

In dentistry, a crown or a dental cap is a type of dental restoration that completely caps or encircles a tooth or dental implant. A crown may be needed when a large dental cavity threatens the health of a tooth. Some dentists will also finish root canal treatment by covering the exposed tooth with a crown. A crown is typically bonded to the tooth by dental cement. They can be made from various materials, which are usually fabricated using indirect methods. Crowns are used to improve the strength or appearance of teeth and to halt deterioration. While beneficial to dental health, the procedure and materials can be costly.

<span class="mw-page-title-main">Inlays and onlays</span> Restoration procedure in dentistry

In dentistry, inlays and onlays are used to fill cavities, and then cemented in place in the tooth. This is an alternative to a direct restoration, made out of composite, amalgam or glass ionomer, that is built up within the mouth.

Periodontology or periodontics is the specialty of dentistry that studies supporting structures of teeth, as well as diseases and conditions that affect them. The supporting tissues are known as the periodontium, which includes the gingiva (gums), alveolar bone, cementum, and the periodontal ligament. A periodontist is a dentist that specializes in the prevention, diagnosis and treatment of periodontal disease and in the placement of dental implants.

A removable partial denture (RPD) is a denture for a partially edentulous patient who desires to have replacement teeth for functional or aesthetic reasons and who cannot have a bridge for any reason, such as a lack of required teeth to serve as support for a bridge or financial limitations.

A dental emergency is an issue involving the teeth and supporting tissues that are of high importance to be treated by the relevant professional. Dental emergencies do not always involve pain, although this is a common signal that something needs to be looked at. Pain can originate from the tooth, surrounding tissues or can have the sensation of originating in the teeth but be caused by an independent source. Depending on the type of pain experienced an experienced clinician can determine the likely cause and can treat the issue as each tissue type gives different messages in a dental emergency.

<span class="mw-page-title-main">CAD/CAM dentistry</span> Computer-aided design and manufacturing of dental prostheses

CAD/CAM dentistry is a field of dentistry and prosthodontics using CAD/CAM to improve the design and creation of dental restorations, especially dental prostheses, including crowns, crown lays, veneers, inlays and onlays, fixed dental prostheses (bridges), dental implant supported restorations, dentures, and orthodontic appliances. CAD/CAM technology allows the delivery of a well-fitting, aesthetic, and a durable prostheses for the patient. CAD/CAM complements earlier technologies used for these purposes by any combination of increasing the speed of design and creation; increasing the convenience or simplicity of the design, creation, and insertion processes; and making possible restorations and appliances that otherwise would have been infeasible. Other goals include reducing unit cost and making affordable restorations and appliances that otherwise would have been prohibitively expensive. However, to date, chairside CAD/CAM often involves extra time on the part of the dentist, and the fee is often at least two times higher than for conventional restorative treatments using lab services.

Fixed prosthodontics is the branch of prosthodontics that focuses on dental prostheses that are permanently affixed (fixed). Crowns, bridges, inlays, onlays, and veneers are some examples of indirect dental restorations. Prosthodontists are dentists who have completed training in this specialty that has been recognized by academic institutes. Fixed prosthodontics can be used to reconstruct single or many teeth, spanning tooth loss areas. The main advantages of fixed prosthodontics over direct restorations are improved strength in big restorations and the possibility to build an aesthetic-looking tooth. The concepts utilised to select the suitable repair, as with any dental restoration, include consideration of the materials to be used, the level of tooth destruction, the orientation and placement of the tooth, and the condition of neighboring teeth.

<span class="mw-page-title-main">Crown lengthening</span> Dental procedure

Crown lengthening is a surgical procedure performed by a dentist, or more frequently a periodontist, where more tooth is exposed by removing some of the gingival margin (gum) and supporting bone. Crown lengthening can also be achieved orthodontically by extruding the tooth.

A post and core crown is a type of dental restoration required where there is an inadequate amount of sound tooth tissue remaining to retain a conventional crown. A post is cemented into a prepared root canal, which retains a core restoration, which retains the final crown.

A resin-retained bridge is a bridge replacing a missing tooth that relies for its retention on a composite resin cement. It is one of many available dental restoration methods which is considered minimally invasive and conservative of tooth tissue. The resin-retained-bridge has gone through a number of iterations. Perhaps the best known is the Maryland bridge and other designs used in the past include the Rochette bridge. The five-year survival rate is around 83.6% and the ten-year rate at 64.9%. The case selection is important and as with any dental prosthesis, good oral hygiene is paramount for success. In recent years, the indications for the use of resin-retained-bridges have diminished significantly and there have been changes in the principles underpinning their design. Resin-retained-bridges should be considered when a fixed prosthesis retained by natural teeth is required. The use has been driven by the advent of evidence-based dentistry showing the benefits to patients of reduced tooth preparation and the importance of an intact enamel structure for the long-term health of the teeth. The bridge is currently in favour in the United Kingdom for these reasons. Indeed, recent contemporary research shows resin retained bridges have better success rates than implants and are a cheaper alternative.

<span class="mw-page-title-main">Bite registration</span> Technique in dentistry

Bite registration is a technique carried out in dental procedures, by taking an impression of the teeth, to capture the way the teeth meet together. This is then used to accurately make restorations which will not change the position the teeth meet in.

<span class="mw-page-title-main">Tooth mobility</span> Medical condition

Tooth mobility is the horizontal or vertical displacement of a tooth beyond its normal physiological boundaries around the gingival (gum) area, i.e. the medical term for a loose tooth.

Pediatric crowns are dental crowns that provide full coverage for primary teeth. They can be made of different materials including stainless steel, polycarbonate, zirconium, or composite resin.

A complete denture is a removable appliance used when all teeth within a jaw have been lost and need to be prosthetically replaced. In contrast to a partial denture, a complete denture is constructed when there are no more teeth left in an arch; hence, it is an exclusively tissue-supported prosthesis. A complete denture can be opposed by natural dentition, a partial or complete denture, fixed appliances or, sometimes, soft tissues.

<span class="mw-page-title-main">Overdenture</span> Removable dental prosthesis

Overdenture is any removable dental prosthesis that covers and rests on one or more remaining natural teeth, the roots of natural teeth, and/or dental implants. It is one of the most practical measures used in preventive dentistry. Overdentures can be either tooth supported or implant supported. It is found to help in the preservation of alveolar bone and delay the process of complete edentulism.

Full arch restoration in dentistry refers to the comprehensive reconstruction or rehabilitation of an entire dental arch, which can include all teeth in the upper or lower jaw. This procedure is also known as full mouth reconstruction or full mouth rehabilitation.

References

  1. 1 2 3 Mitchell DA, Mitchell L, McCaul L (2014). Oxford Handbook of Clinical Dentistry (Sixth ed.). Oxford: Oxford University Press. p. 268.
  2. 1 2 "The Glossary of Prosthodontic Terms: Ninth Edition". The Journal of Prosthetic Dentistry. 117 (5S): e1–e105. May 2017. doi: 10.1016/j.prosdent.2016.12.001 . hdl:2027/mdp.39015007410742. PMID   28418832.
  3. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 "Planning and making crowns", Planning and Making Crowns and Bridges, Fourth Edition, CRC Press, 2006-10-05, pp. 105–121, doi:10.3109/9780203090633-7, ISBN   9780415398503
  4. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A., Shillingburg, Herbert T. Sather, David (2014-08-02). Fundamentals of fixed prosthodontics. Quintessence Pub. ISBN   9780867155174. OCLC   885208898.{{cite book}}: CS1 maint: multiple names: authors list (link)
  5. 1 2 Bartlett D, Ricketts D (2013). Advanced operative dentistry : a practical approach. Edinburgh: Elsevier Churchill Lvgst. ISBN   978-0-7020-5538-6.
  6. ↑ Hemmings K, Harrington Z (April 2004). "Replacement of missing teeth with fixed prostheses". Dental Update. 31 (3): 137–41. doi:10.12968/denu.2004.31.3.137. PMID   15116483.
  7. ↑ Bishop K, Addy L, Knox J (2007). "Modern restorative management of patients with congenitally missing teeth: 3. Conventional restorative options and considerations". Dental Update. 34 (1): 30–2, 34, 37–8. doi:10.12968/denu.2007.34.1.30. PMID   17348556.
  8. ↑ Maglad AS, Wassell RW, Barclay SC, Walls AW (August 2010). "Risk management in clinical practice. Part 3. Crowns and bridges". British Dental Journal. 209 (3): 115–22. doi:10.1038/sj.bdj.2010.675. PMID   20706245. S2CID   205664319.
  9. 1 2 3 4 Briggs P, Ray-Chaudhuri A, Shah K (March 2012). "Avoiding and managing the failure of conventional crowns and bridges". Dental Update. 39 (2): 78–80, 82–4. doi:10.12968/denu.2012.39.2.78. PMID   22482265.
  10. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Ibbetson R, Hemmings K, Harris I (May 2017). "Guidelines for Crowns, Fixed Bridges and Implants". Dental Update. 44 (5): 374–6, 378–80, 382–4, 386. doi:10.12968/denu.2017.44.5.374. PMID   29188690.
  11. 1 2 3 4 5 6 7 8 9 10 Gulati JS, Tabiat-Pour S, Watkins S, Banerjee A (2016). "Resin-Bonded Bridges – the Problem or the Solution? Part 1- Assessment and Design". Dental Update. 43 (6): 506–8, 510–2, 515–8, 521. doi:10.12968/denu.2016.43.6.506. PMID   29148644.
  12. 1 2 Dayanik S (April 2016). "Resin-Bonded Bridges--Can We Cement Them 'High'?". Dental Update. 43 (3): 243–4, 247–50, 253. doi:10.12968/denu.2016.43.3.243. PMID   27439271.
  13. 1 2 3 4 5 Gopakumar A, Boyle EL (September 2013). "'A bridge too far'--the negative impact of a bridge prosthesis on gingival health and its conservative management". British Dental Journal. 215 (6): 273–6. doi: 10.1038/sj.bdj.2013.877 . PMID   24072295.
  14. ↑ Reddy K, Hegde V, Aparna IN, Dhanasekar B (2009). "Incorporating modified ovate pontic design for anterior tooth replacement: A report of two cases". Journal of Indian Prosthodontic Society. 9 (2): 100–4. doi: 10.4103/0972-4052.55254 .
  15. ↑ network, MEFANET, Czech and Slovak medical faculties. "Division of pontics according to shape and relation to the mucosa. - WikiLectures". www.wikilectures.eu. Retrieved 2018-06-14.{{cite web}}: CS1 maint: multiple names: authors list (link)
  16. 1 2 3 Rosenstiel SF, Land MF, Junhei F (2006). Contemporary fixed prosthodontics (4th ed.). St. Louis: Mosby. ISBN   978-0-323-02874-5.[ page needed ]
  17. 1 2 Smith BG (1998). Planning and Making Crowns and Bridges (3rd ed.). London: Taylor & Francis, A Martin Dunitz Book. ISBN   978-0-203-41955-7.[ page needed ]
  18. ↑ Nallaswamy D (2003). Textbook of prosthodontics (1st ed.). New Delhi: Jaypee Brothers Medical Publishers. ISBN   9788180611995.[ page needed ]
  19. ↑ Kim SH, Watts DC (January 2004). "Polymerization shrinkage-strain kinetics of temporary crown and bridge materials". Dental Materials. 20 (1): 88–95. doi:10.1016/S0109-5641(03)00101-5. PMID   14698778.
  20. ↑ Astudillo-Rubio D, Delgado-Gaete A, Bellot-Arcís C, Montiel-Company JM, Pascual-Moscardó A, Almerich-Silla JM (2018-02-28). "Mechanical properties of provisional dental materials: A systematic review and meta-analysis". PLOS ONE. 13 (2): e0193162. Bibcode:2018PLoSO..1393162A. doi: 10.1371/journal.pone.0193162 . PMC   5830998 . PMID   29489883.
  21. ↑ Ahmad I (2012). Prosthodontics at a glance. Chichester, West Sussex, UK: Wiley-Blackwell. ISBN   978-1-405-17691-0.[ page needed ]
  22. ↑ Pieger S, Salman A, Bidra AS (July 2014). "Clinical outcomes of lithium disilicate single crowns and partial fixed dental prostheses: a systematic review". The Journal of Prosthetic Dentistry. 112 (1): 22–30. doi:10.1016/j.prosdent.2014.01.005. PMID   24674802.
  23. ↑ Willard A, Gabriel Chu TM (April 2018). "The science and application of IPS e.Max dental ceramic". The Kaohsiung Journal of Medical Sciences. 34 (4): 238–242. doi: 10.1016/j.kjms.2018.01.012 . hdl: 1805/17095 . PMID   29655413.
  24. ↑ Magne P, Perroud R, Hodges JS, Belser UC (October 2000). "Clinical performance of novel-design porcelain veneers for the recovery of coronal volume and length". The International Journal of Periodontics & Restorative Dentistry. 20 (5): 440–57. PMID   11203582.
  25. ↑ Manicone PF, Rossi Iommetti P, Raffaelli L (November 2007). "An overview of zirconia ceramics: basic properties and clinical applications". Journal of Dentistry. 35 (11): 819–26. doi:10.1016/j.jdent.2007.07.008. PMID   17825465.
  26. ↑ Daou EE (2014). "The zirconia ceramic: strengths and weaknesses". The Open Dentistry Journal. 8: 33–42. doi: 10.2174/1874210601408010033 . PMC   4026739 . PMID   24851138.
  27. ↑ Le M, Papia E, Larsson C (June 2015). "The clinical success of tooth- and implant-supported zirconia-based fixed dental prostheses. A systematic review" (PDF). Journal of Oral Rehabilitation. 42 (6): 467–80. doi:10.1111/joor.12272. hdl: 2043/18632 . PMID   25580846.
  28. ↑ Larsson C (2011). "Zirconium dioxide based dental restorations. Studies on clinical performance and fracture behaviour". Swedish Dental Journal. Supplement (213): 9–84. PMID   21919311.
  29. ↑ Bahat Z, Mahmood DJ, Vult von Steyern P (2009). "Fracture strength of three-unit fixed partial denture cores (Y-TZP) with different connector dimension and design". Swedish Dental Journal. 33 (3): 149–59. PMID   19994565.
  30. ↑ Vult von Steyern P (2005). All-ceramic fixed partial dentures. Studies on aluminum oxide- and zirconium dioxide-based ceramic systems. Swedish Dental Journal. Supplement (Doctoral Thesis). pp. 1–69. hdl:2043/1635. PMID   16001730.
  31. ↑ Poggio CE, Ercoli C, Rispoli L, Maiorana C, Esposito M (December 2017). "Metal-free materials for fixed prosthodontic restorations" (PDF). The Cochrane Database of Systematic Reviews. 12 (11): CD009606. doi:10.1002/14651858.CD009606.pub2. PMC   6486204 . PMID   29261853.
  32. ↑ WorkNC Dental machining video, “Dental Bridge implant CNC Machining 5 axis”
  33. ↑ PATTERN RESIN™ LS Self-Curing, Acrylic Die Material
  34. ↑ "Dental bridges. Advantages and disadvantages". infodentis.com.
  35. ↑ Kc Basnyat S, Sapkota B, Shrestha S (October 2015). "Oral Hygiene and Gingival Health in Patients with Fixed Prosthodontic Appliances - A Six Month Follow-up". Kathmandu University Medical Journal. 13 (52): 328–32. doi: 10.3126/kumj.v13i4.16832 . PMID   27423283.
  36. ↑ Ortolan SM, Viskić J, Stefancić S, Sitar KR, Vojvodić D, Mehulić K (March 2012). "Oral hygiene and gingival health in patients with fixed prosthodontic appliances--a 12-month follow-up". Collegium Antropologicum. 36 (1): 213–20. PMID   22816223.
  37. 1 2 3 Mitchell L, Mitchell DA, McCaul L (2014). Oxford Handbook Clinical Dentistry (Sixth ed.). Oxford: Oxford University Press. p. 276.
  38. ↑ Hargreaves K, Berman L (2010). Cohen's Pathways of the Pulp Expert Consult. Mosby Elsevier. ISBN   978-0-323-06489-7.[ page needed ]
  39. ↑ Plengsombut K, Brewer JD, Monaco EA, Davis EL (March 2009). "Effect of two connector designs on the fracture resistance of all-ceramic core materials for fixed dental prostheses". The Journal of Prosthetic Dentistry. 101 (3): 166–73. doi:10.1016/S0022-3913(09)60022-6. PMID   19231568.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.