Fender Prosonic

Last updated

The Fender Prosonic guitar amplifier was produced by Fender Musical Instruments from 1996 to 2002. Available in head and combo versions, the Prosonic featured several departures in design from traditional Fender amplifiers such as the Bassman, Twin Reverb, and Deluxe Reverb. Designed by Bruce Zinky as a project for the Fender Custom Shop, the amplifier later had a non-Custom Shop production run at the Fender facilities in Corona, California. (Most contemporary Fender amplifiers are produced in Mexico.) It was initially priced to compete with buyers in the so-called boutique amplifier market who were seeking more distortion than any previous Fender had ever offered. It is believed that high list prices, and deviations from established Fender amplifier designs, swayed many buyers away from the Prosonic. It developed a cult following among serious guitarists, aided by the rise of musician-centric Internet communities.[ citation needed ]

Contents

Innovations and sound

The Prosonic introduced several features that had previously been seldom, or never before, seen in Fender amplifiers. Its most unusual feature is the switchable rectifier and power amplifier bias scheme, allowing on-the-fly changes of operating mode and output power (as well as subjective tonal differences). This feature, originally found on Randall Smith's Mesa Boogie amplifiers, allows the Prosonic to achieve a versatility very rarely seen from mass-market instrument manufacturers. The Prosonic's rear-mounted RECTIFIER/BIAS switch lets the user select from the following three options:

  1. Solid-state rectification with fixed bias (marked "S.S. AB2"). Listed at 60 watts R.M.S.
  2. Tube rectification with fixed bias (marked "AB2"). Listed at 50 watts R.M.S.
  3. Tube rectification with cathode bias (marked "A"). Listed at 30 watts R.M.S.

Unlike many amplifiers marketed as "Class A", the Prosonic truly functions as a Class A power amplifier in the "A" position. Class A refers to the amount of current flowing through the power tubes with zero audio signal, with Class A meaning maximum current flow even with zero signal. This makes the tubes run hotter, and gives the power section even more gain at the cost of tube life and noise. The Class-A designation for guitar amplifiers is often a misnomer; Few amps outside of the heralded Vox AC-30, also with cathode bias, operate in a true Class-A mode [Albeit, it only did so up to ≈21 watts RMS]. While the Prosonic featured cathode bias in the Class A mode and fixed bias in the Class AB mode, not all class A tube amplifiers are cathode-biased, and not all fixed biased amplifiers are Class AB. Fixed bias amps, however, require lower B+ Voltages to stay within the Plate Dissipation of the power tubes used; Cathode biasing "throws away" this voltage using conventional Higher Voltage power supplies.

A channel-switching amp, the Prosonic offers a clean channel that features a blend of traditional Fender sounds with the influence of Vox amplifiers, frequently attributed to the Class A mode. Many players praise the Prosonic's clean channel as being "softer," and more prone to break-up and musically desirable distortion, than more contemporary Fender designs. Detractors view this trait as an apparent "darkness" in tone, and perceive this lack of the typical Fender "sparkle" as merely an undesirable lack of clean headroom.

The Prosonic also brought levels of gain (distortion) previously unavailable in a Fender amplifier. Taking a major cue from the first generation of Mesa Boogie amplifiers such as the Mark I (itself a modified Fender design), the Prosonic used additional gain stages in the preamp section that cascaded into one another. Although Fender had been designing amps with some facility for built-in distortion/overdrive since at least the late 1960s, never before had they arrived at a sound so readily usable for modern high-gain styles of music, and far removed from what many players consider to be archetypical Fender tones. The Prosonic's factory manual states, "Gain 1 functions as a standard gain stage whereas Gain 2 functions similar to a compressor, adding sustain while reducing 'edge' when the volume is increased. This channel produces great high gain sound at any volume—from bedroom to stadium."

Configurations and cosmetics

Prosonics were available first from the Fender Custom Shop, and later from Fender Musical Instruments, and for each production run, combo amplifiers featuring dual Celestion 10" speakers, and head versions were available. (Zinky did make prototype combo versions with a single 12-inch speaker). The circuitry is identical and offers users the sound similar to a louder Deluxe Reverb. The combo version featured a tube-driven, Accutronics spring reverb unit. The head version omitted the reverb tank.

While the vast majority of Prosonics were shipped with the standard black tolex covering, some of the initial Custom Shop run were finished in red and seafoam green pebbled tolex, called "lizard-skin" by Fender. Approximately 300 were made in red and 500 were made in seafoam green. The look of the amplifier borrows simultaneously from several eras of vintage Fender design: black "chicken-head" pointer knobs (as used on circa 1950s "tweed" amps), and the silver grill cloth, jewel lamp, and black control plate as used during the 'black face' period (mid-1960s). (Both models came with green jewel lamps).

Specifications and electronics

An all-tube design, the Prosonic uses standard 12AX7A tubes in the preamp sections, and one for the reverb send on the combo model. Output tubes are 5881/6L6WGCs. The rectifier tube is a 5AR4 (GZ34). The spring reverb unit in the combo model also uses a 12AT7 tube.

Although the Prosonic is a channel-switching amp, both channels share the same EQ section. Defying conventional logic, the Prosonic offers independent master volumes for each channel, or rather, on the clean channel, simply one volume control. The drive channel features the aforementioned dual cascading-gain controls, plus an additional master volume.

Two outputs for speaker cabinets are provided, (with switchable 4/8/16-ohm operation on the head version). The back panel also provides for a line-level effects loop, as well as an input for the channel-switching footswitch (the footswitch had a reverb button on combo models as well).

Discontinuation

The Prosonic initially sold well, outselling the '94 Twin (even though the Prosonic had a higher price and fewer features). However, overproduction of the amplifiers led to overstock. This, factored with its remaining unchanged for five years (as new products get the most attention at music stores), led Fender to close out the Prosonic inventory and discontinue the product.

Towards the end of the 1990s, poor sales relegated many of the existing stock of Prosonics to closeout sale status.[ citation needed ] Theories abound as to why it was never a great success with players; foremost was its high price. It was simply perceived[ by whom? ] as too much money despite innovative design and glowing reviews. The Prosonic also suffered from something of an identity crisis; the cosmetics suggested classic Fender tones, and many players[ who? ] desiring an amp for blues or country playing, for example, were put off by the over-the-top lead channel. Conversely, the demographic for high-gain amplifiers, generally the domain of practitioners of heavy metal and the fledgling nu metal genre, and dominated by products from Marshall and Mesa Boogie, had long written off Fender as incapable of producing amplifiers catering to their style.[ citation needed ] The combo's 10-inch speakers, though specially designed and voiced for the Prosonic to handle huge amounts of power, were seen as too small by players favoring 12-inch speakers. The mechanical relay-based channel switching, designed to provide a more pure signal path, produced a large pop upon channel switching at low volumes, unlike other electronically buffered designs—this deliberate design choice was nonetheless perceived as the premier "design flaw" among players. Several of the Prosonic's other quirkier design elements, such as the shared EQ and line-level effects loop, were designed for studio use and weren't ideal for live playing. Understandably, buyers were attracted to the amp's flexibility and, when used on-stage, these studio-friendly features were perceived as design flaws. Like with many other high-powered combo amplifiers, the Prosonic's weight, at 60 lbs, was another less-than-popular characteristic.[ citation needed ]

Influence on future products

In 2006, Fender introduced the Super-Sonic model, which draws heavily on elements of the Prosonic. Available in head and 1×12-inch combo forms (as opposed to the Prosonic combo's 2×10" form), the Super-Sonic also features the pre-Silverface voiced clean channel paired with the cascading-gain drive channel as pioneered on the Prosonic. Absent is the switchable rectifier or facility to run the amplifier in Class A mode, but a two-channel EQ has been added to the clean side, as well as a "voicing switch" offering tones inspired by the classic Fender Vibrolux and Fender Bassman models. With a footswitch, this was essentially the same as having two distinct clean channels that shared the same tone controls. Two generations were produced, distinguishable by their logo.

Originally produced in both 22 watt (6V6 output tubes) and 60 watt (6L6 output tubes), as of 2016, only the 22 watt version remains in production, however the 60 watt version remains available in both head and combo versions in second quarter 2017. While the combo versions sharing the same cabinet and pre-amp design, the output transformer, output tubes and single 12" speaker differed. Priced higher than most Fender amplifiers, appeal was somewhat limited to musicians seeking the advanced features, much like the Prosonic. Unlike the Prosonic, all Super-Sonic amps used a solid state rectifier only. Super-Sonic amps are manufactured in Fender's Corona, California factory.

Notes

    Related Research Articles

    <span class="mw-page-title-main">Guitar amplifier</span> Electronic amplifier for musical instruments

    A guitar amplifier is an electronic device or system that strengthens the electrical signal from a pickup on an electric guitar, bass guitar, or acoustic guitar so that it can produce sound through one or more loudspeakers, which are typically housed in a wooden cabinet. A guitar amplifier may be a standalone wood or metal cabinet that contains only the power amplifier circuits, requiring the use of a separate speaker cabinet–or it may be a "combo" amplifier, which contains both the amplifier and one or more speakers in a wooden cabinet. There is a wide range of sizes and power ratings for guitar amplifiers, from small, lightweight "practice amplifiers" with a single 6-inch speaker and a 10-watt amp to heavy combo amps with four 10-inch or four 12-inch speakers and a 100-watt amplifier, which are loud enough to use in a nightclub or bar performance.

    <span class="mw-page-title-main">Marshall Amplification</span> British company

    Marshall is a British company that designs and manufactures music amplifiers, speaker cabinets, brands personal headphones and earphones, drums and bongos. The company also owns a record label called Marshall Records. It was founded in London by drum shop owner and drummer, Jim Marshall, and is now based in Bletchley, Milton Keynes, England.

    <span class="mw-page-title-main">Fender amplifier</span>

    Fender amplifiers are a series of electric instrument amplifiers produced by the Fender Musical Instruments Corporation. The first guitar amplifiers attributed to Leo Fender were manufactured by the K&F Manufacturing Corporation (K&F) between 1945 and 1946. Later, Fender began building its own line of electric guitars. Fender amplifiers would become favorite of many famous guitarists such as Jimi Hendrix, Eric Clapton, and Stevie Ray Vaughan, also known in these cases for playing Fender guitars.

    <span class="mw-page-title-main">Vox AC30</span> Guitar amplifier

    The Vox AC30 is a guitar amplifier manufactured by Vox. It was introduced in 1958 to meet the growing demand for louder amplifiers. Characterised by its "jangly" high-end sound it has become widely recognized by British musicians and others, such as George Harrison and John Lennon of the Beatles, Bill Wyman of the Rolling Stones, Brian May of Queen, Dave Davies of the Kinks and Hank Marvin.

    <span class="mw-page-title-main">Fender Twin</span> Guitar amplifier

    The Fender Twin and Twin Reverb are guitar amplifiers made by Fender Musical Instruments Corporation. The Twin was introduced in 1952, two years before Fender began selling Stratocaster electric guitars. The amps are known for their characteristically clean tone.

    <span class="mw-page-title-main">Fender Hot Rod Deluxe</span>

    The Fender Hot Rod Deluxe is a guitar amplifier manufactured and sold by the Fender Musical Instruments Corporation. It was introduced in 1996 as part of the "Hot Rod" line of guitar amplifiers and has been in continuous production since. The Hot Rod Deluxe is a modified version of the Fender Blues Deluxe from the earlier Blues line of amplifiers, and has a higher level of gain in its preamplification signal. This model, along with the Hot Rod Deville, were originally designated as F.A.T. amplifiers but this moniker was dropped in 2002 when production of this series of amps was moved from Corona, CA to Fender's Baja-Ensenada, Mexico manufacturing facility.

    <span class="mw-page-title-main">Epiphone Valve Junior</span>

    The Epiphone Valve Junior is a small 5 watt class A electric guitar amplifier.

    <span class="mw-page-title-main">Fender Bassman</span>

    The Fender Bassman is a series of bass amplifiers introduced by Fender during 1952. Initially intended to amplify bass guitars, musicians used the 5B6 Bassman to amplify other instruments, including electric guitars, harmonicas, and pedal steel guitars. Besides being a popular and important amplifier in its own right, the Bassman also became the foundation on which Marshall and other companies built their high-gain tube amplifiers.

    <span class="mw-page-title-main">Fender Deluxe Reverb</span>

    The Fender Deluxe Reverb is a guitar amplifier made by the Fender Electric Instrument Company and its successors. It was first introduced in 1963 by incorporating an onboard spring reverb tank to the newly redesigned Fender Deluxe amplifier.

    <span class="mw-page-title-main">Fender Hot Rod DeVille</span> Guitar amplifier

    The Fender Hot Rod DeVille is a combo tube guitar amplifier manufactured and sold by Fender. It was introduced in 1996 as part of Fender's Hot Rod line of amplifiers, and since then has been in continuous production. The Hot Rod DeVille is a modified version of the earlier Fender Blues DeVille from the Blues amplifier line, and has a higher level of gain in its preamplification signal. The DeVille incorporates a 60 watt amplifier, and is available in two different models: a 212, which includes a pair of Celestion A-Type 12" speakers, and the 410, which includes four 10" speakers. The DeVille is the sister amplifier of the Fender Hot Rod Deluxe.

    The Fender Concert was a guitar amplifier made by Fender Musical Instruments. Its production can be split over 2 phases. The first of these running from 1960 and until approximately 1965, at which time a typical Fender Concert was priced at $315. During the 1960s, the Concert was for all practical purposes the same amplifier as the Vibrasonic but with four 10" speakers. In a later phase, the Concert was updated by Paul Rivera in the early 1980s and a subsequent 1x12 variant of the Concert amp appeared briefly in the mid-1990s.

    <span class="mw-page-title-main">Fender Champ</span>

    The Fender Champ was a guitar amplifier made by Fender. It was introduced in 1948 and discontinued in 1982. An updated version was introduced in 2006 as part of the "Vintage Modified" line.

    The Peavey 5150 is a vacuum tube based guitar amplifier made by Peavey Electronics from 1992 on. The amplifier was initially created as a signature model for Eddie Van Halen. After Van Halen and Peavey parted ways in 2004, the name was changed to Peavey 6505. The 5150 name was used again by Van Halen in partnership with Fender under the EVH brand. Peavey's amplifier was renamed to 6505 in celebration of Peavey's 40th anniversary (1965–2005).

    <span class="mw-page-title-main">Mesa Boogie Mark Series</span>

    The Mesa Boogie Mark Series is a series of guitar amplifier made by Mesa Engineering. Originally just referred to as "Boogies," the product line took on the moniker "Mark Series" as newer revisions were put into production. The Mark Series amplifier was Mesa's flagship product until the introduction of the Rectifier series, and the amplifiers are collectable.

    The Fender Deluxe guitar amplifier is a range of non-reverb guitar amplifiers produced by Fender. The amplifiers were originally produced from early 1948 to 1966 and reissues are in current production. Its predecessor was the Fender Model 26 "Woodie" produced from 1946 to 1948.

    <span class="mw-page-title-main">Fender Pro Reverb</span>

    The Fender Pro Reverb is a high-end guitar amplifier made by Fender. It was in production from 1965 and was discontinued in 1982. The Pro Reverb is a 40-watt tube amplifier and has a pair of 12-inch (30 cm) speakers; however, models later than 1976 were increased to 70 watts. Teagle and Sprung, authors of the definitive book on Fender amplifiers described the Blackface Pro Reverb as the best amplifier ever produced likely due to its combination of the two twelve inch speakers, its high quality reverb and tremolo, and just the right amount of power to get either classic Blackface Fender cleans or natural tube breakup at reasonable volumes. They wrote, "the author recommends these amps as the best all-around amp ever made—by anyone".

    <span class="mw-page-title-main">Fender Vibroverb</span>

    The Fender Vibroverb was a 40-watt combo guitar amplifier originally manufactured in 1963 and 1964. It was the first Fender amplifier to incorporate on-board reverb and tremolo/vibrato, which became a standard feature on many high-end Fender tube amps during the 1960s and 1970s.

    <span class="mw-page-title-main">Jim Kelley Amplifiers</span>

    Jim Kelley Amplifiers is the trademark for the vacuum tube guitar amplifiers designed by Jim Kelley and manufactured by his company Active Guitar Electronics of Tustin, California between the years of 1978 and 1985. Approximately 600 of these amps were built during that time. The single-channel version of the amplifier employed modest gain in the preamp stages, Baxandall type bass and treble controls, a split load phase inverter, and four 6V6GT output tubes. The amplifiers produce 60 watts RMS at full power, and include a half power (30/60) switch.

    The Fender Pro was an instrument amplifier manufactured by Fender Electric Instruments from 1946 to 1965. It was characterized by its dual 6L6-family power tubes and single 15" speaker, with output power increasing from 18 watts up to 40 watts over its production run. The Pro was replaced in the Fender lineup by its offspring the Pro Reverb.