| IAR CV 11 | |
|---|---|
 | |
| Role | Fighter |
| National origin | Romania |
| Manufacturer | IAR (Industria Aeronautică Română) |
| Designer | Elie Carafoli Lucien Virmoux |
| First flight | 1930 |
| Introduction | never |
| Primary user | Romania |
| Number built | 2 |
The IAR CV 11 was a Romanian fighter prototype in 1930, designed by Elie Carafoli, and it was IAR's first original aircraft.
In early 1930 a contest was called by the ARR for a new fighter type to equip its squadrons. During July and October, seven foreign types were tested at an airfield near Bucharest. No decision was made, however, since none of the contenders reached the minimal speed limit set by the requirements at 300 km/h (190 mph; 160 kn). Despite the inconclusive results, the favourite plane seemed to be the chunky-looking Polish P.Z.L. P.1/II prototype, registered SP-ADO. During the same period, the air force commission was informed that a new fighter prototype had been completed at I.A.R., and it had reached an impressive 319 km/h (198 mph; 172 kn) top speed during initial test flights.
Built according to the plans of Dipl.-Eng. Dr. Elie Carafoli and Lucien Virmoux, the I.A.R. fighter was an advanced construction. Named the C.V. 11 after its designers, it had a mixed metal-wood structure and cantilever, low-wing configuration, modern features soon to be adopted by all major aircraft manufacturers. The front fuselage structure was made of duraluminum tubes, while the rear part was of pinewood. The engine nacelle and the fuselage up to the cockpit were covered by duraluminum sheets, the aft part by plywood. The rear part of the fuselage merged with the tail without a substantial cross-sectional change, giving the aircraft a rather unusual arrow-like look. Due to its unconventional fuselage configuration the overall length came to less than 7 m, while the height was only 2.46 m (8 ft 1 in). The 11.5 m (38 ft) span wing was made up by three sections of combined duraluminum/pinewood construction, reinforced by steel cables. The centre part housed the main wing fuel tank. The unbalanced control surfaces, which proved to be too small during trials, were made entirely of wood covered by fabric.
The powerplant chosen was a Lorraine-Dietrich 12Fa Courlis with 12 cylinders arranged in a W configuration. Its maximum output was an impressive 600 hp (450 kW) but it proved to be too heavy for the small and light fuselage, which weighted only 1,100 kg (2,400 lb), and caused a dangerous tendency to go into a spin at low speed. This shortcoming could not be eliminated, so the prototype, officially designated I.A.R. C.V. 11/W.8, had finally to be abandoned.
In the meantime, a second prototype was completed at I.A.R. This time a less powerful but sensibly lighter Hispano-Suiza 12Mc engine, with 12-cylinders in V, had been fitted to essentially the same fuselage. Although weaker than its predecessor, this engine gave a superior maximum speed of 328 km/h at sea level and 295 km/h at 5,000 m.
The armament of two 7.7 mm (0.303 in) Vickers machine guns firing through the propeller arc had been retained from the first prototype. An O.P.L. type gunsight helped the pilot to aim its guns.
After initial test flights, the second prototype, designated in French style I.A.R. C.V. 11 C1 (Chasseur monoplace), had been shipped to Istres, in France, where it arrived in January 1931. During the following two months further trials were conducted involving French specialists as well.
The French specialists report, however, did not have any significant effect on ARR commission members. After the initial failure in reaching a verdict, this prompted the ARR leaders to set up a new, five member committee to decide the choice of fighter type to be introduced into Romanian service. After several months of inquiries and test flights, the commission finally decided four to one in favour of the P.Z.L. P.1 and against the faster but less manoeuvrable, spin-prone I.A.R. C.V. 11.
Therefore, once the prototype returned to Romania, as a last measure, the I.A.R. team decided to make an attempt to break the speed record on a 500 km (310 mi) closed circuit. The record of 306.696 km/h (190.572 mph; 165.603 kn) in effect at that time for this category had been set up by the Frenchman Joseph Sadi-Lecointe, with a Nieuport-Delâge airplane.
The record-breaking attempt was scheduled for the morning of 9 December 1931 on the Bucharest-Fetești-Bucharest route. With the Capitan aviator Romeo Popescu at its controls, the C.V. 11 took off from Pipera-Bucharest military airfield at 11.30 a.m. The first 370 km were flown without any trouble at an encouraging average speed. Close to Lehliu railway station, however, the overheated Hispano-Suiza engine suddenly stalled, forcing the pilot to try an improvised forced landing with the now vicious airplane. Cpt. Popescu approached a nearby open field, but at contact with the thick snow cover one of the main wheels collapsed and the fighter turned over, crushing the pilot under the fuselage. Romeo Popescu, an experienced test pilot and holder of three Romanian national aviation records, died instantly. The investigation following the incident concluded that the lubrication of the overstressed engine, working at maximum power, was insufficient, causing seizure. Until that fatal moment, during an hour and thirty-four minutes of flight, an average speed of 319 km/h had been recorded by the onboard instruments, thus a good chance had existed of achieving the goal set by the temerarious pilot.
However, by that time the dice had already been cast. Months before, in September 1931, General Constantin Lazarescu, the new inspector of DSA, decided not to consider the I.A.R. design any more, but to purchase the Polish P.Z.L. P.11, an upgraded version of the initial P.1.
Data from Jane's all the World's Aircraft 1931 [1]
General characteristics
Performance
Armament
The IAR 80 was a Romanian World War II low-wing monoplane, all-metal monocoque fighter and ground-attack aircraft. When it first flew, in 1939, it was comparable to contemporary designs being deployed by the airforces of the most advanced military powers such as the Hawker Hurricane and Bf 109E. Production problems and lack of available armament delayed entry of the IAR 80 into service until 1941. It remained in frontline use until May 1945.
The PZL P.11 is a Polish fighter aircraft, designed and produced in the early 1930s by Państwowe Zakłady Lotnicze. Possessing an all-metal structure, metal-covering, and high-mounted gull wing, the type held the distinction of being widely considered the most advanced fighter aircraft in the world at the time of its introduction into service.
The PZL P.7 was a Polish gull wing monoplane fighter aircraft designed in the early 1930s at the PZL factory in Warsaw. It was the main fighter of the Polish Air Force between 1933 and 1935. The PZL P.7 was replaced in Polish service by its follow-up design, the PZL P.11c. More than 30 PZL P.7 fighters remained in service during the Invasion of Poland, scoring several kills despite its obsolescence.
The PZL P.24 is a Polish fighter aircraft, built in the late 1930s by Państwowe Zakłady Lotnicze. It was a much more advanced development of the PZL P.11, a Polish wing all-metal fighter designed by Zygmunt Puławski.
The Avioane Craiova IAR-93 Vultur (Eagle) is a twinjet, subsonic, close support, ground attack and tactical reconnaissance aircraft with secondary capability as low level interceptor. Built as single-seat main attack version or combat capable two-seat version for advanced flying and weapon training, it was developed in 1970s by Romania and Yugoslavia to become more independent from Soviet equipment. The Romanian aircraft were built by I.R.Av. Craiova as IAR-93, and its Yugoslav counterpart by Soko as the Soko J-22 Orao. For Romania, the IAR-93 was intended to replace MiG-15s and MiG-17s in the fighter-bomber role.
The IAR 14 is a Romanian low-wing monoplane fighter-trainer aircraft designed before World War II.
PZL.46 Sum (sheatfish) was a light bomber developed by Państwowe Zakłady Lotnicze shortly before World War II, which, was directed to serial production in the spring of 1939. These planes were in production, but the Polish industry did not manage to produce them before the outbreak of the war.
PZL.50 Jastrząb (Hawk) was a Polish late 1930s fighter aircraft designed by Wsiewołod Jakimiuk at Państwowe Zakłady Lotnicze. The single-seat low-wing monoplane was to serve as a multi-purpose fighter and escort to replace all other fighters in the Polish Military Aviation. Designed after 1936, its prototype first flew in February 1939. By September, the first production aircraft were nearing completion, but further development was interrupted by the Nazi-Soviet Invasion of Poland.
The PZL P.6 was a Polish fighter, designed by the engineer Zygmunt Puławski, manufactured by PZL state-owned factory. It remained a prototype and did not go into production.
PZL.12 (PZL-H) was a prototype of a Polish amphibious flying boat designed and built in 1931 by Zygmunt Puławski, a pioneering Polish designer. He was killed in a crash involving this design.
The Bartel BM 6 was a Polish biplane trainer fighter aircraft of 1930. It did not advance beyond the prototype stage.
The PZL P.1 was a Polish fighter, designed by the engineer Zygmunt Puławski, manufactured by the PZL state-owned factory. It remained a prototype, but it was the first of the Polish PZL gull wing fighter series, leading to the PZL P.7, PZL P.11 and PZL P.24.
The IAR-827 was an agricultural aircraft built in Romania in the 1970s and 1980s. The penultimate member of the family of designs that began with the IAR-821, it was, like the others, a conventional low-wing monoplane with fixed, tailwheel undercarriage, and shared the all-metal construction of the IAR-826. The prototype flew in 1976, powered by a Lycoming IO-720 engine, but the production examples that followed all had the PZL-3S.
The Renard Epervier was a Belgian prototype single-seat all-metal fighter monoplane designed by Alfred Renard at the Societé Anonyme Avions et Moteurs Renard for a government-sponsored design contest in 1928. The Epervier Type 2 was built and flown in 1928, by Belgian aircraft manufacturer Stampe et Vertongen. It carried an armament of two synchronised 7.7mm guns and was lost in September 1928 after failing to recover from a flat spin. A second prototype, the Epervier Type 2bis, introduced revised streamlined fairings for the cantilever mainwheel legs, mainwheel spats and cylinder aft-fairings and was built by SABCA.
PZL.55 was a Polish pre-war project of a fighter aircraft, created at Państwowe Zakłady Lotnicze by Jerzy Dąbrowski. The design was for a single-seat low-wing all-metal monoplane. It was planned that the plane would replace obsolete fighters and lead to a significant increase in the capabilities of Polish Military Aviation.
The IAR 15 was a low-wing monoplane fighter designed in Romania in 1933. Designed by Elie Carafoli for the Romanian Air Force, the IAR 15 was a lightly armed low-wing cantilever monoplane with a radial engine, fixed undercarriage and open cockpit.
The IAR-23 and IAR-24 were low-wing monoplane light multipurpose aircraft with a conventional undercarriage, built by IAR of Romania.
The IAR 12 is a Romanian low-wing monoplane fighter-trainer aircraft designed before World War II.
The IAR 13 is a Romanian low-wing monoplane fighter-trainer aircraft designed before World War II.
PZL P.8 was a Polish fighter aircraft designed by Zygmunt Puławski, from the family of fighters with Polish wing, developed and produced by Państwowe Zakłady Lotnicze (PZL) in the early 1930s.
