Italian corvette San Giovanni

Last updated
RN San Giovanni1.jpg
San Giovanni
Class overview
NameSan Giovanni
Operators
Preceded byNone
Succeeded by Magenta
Completed1
History
Builder Cantiere della Foce
Laid down1848
Launched1849
Fate Broken up, 1878
General characteristics
Type Corvette
Displacement1,752 long tons (1,780  t)
Length53 m (174 ft) loa
Beam12.8 m (42 ft)
Draft5.8 m (19 ft)
Propulsion Full ship rig
Complement345
Armament32 × guns
General characteristics (1862 refit)
Type Screw corvette
Installed power
Propulsion
Speed9 knots (17 km/h; 10 mph)
Range1,515 nautical miles (2,806 km; 1,743 mi) at 9 kn

San Giovanni was a sail corvette built for the Royal Sardinian Navy in the late 1840s. In 1861, she was converted into a screw corvette by which time the unification of Italy had been largely completed. As a result, she served with the Italian Regia Marina when the work on the ship was finished. She was present for the Battle of Lissa in 1866 during the Third Italian War of Independence, though she did not engage the Austrian Navy in the battle. She was eventually laid up in 1875 and broken up for scrap in 1878.

Contents

Design

San Giovanni was 53 m (174 ft) long overall, with a beam of 12.8 m (42 ft) and a draft of 5.8 m (19 ft). [1] She had a displacement of 1,752 long tons (1,780  t ). [2] Her wooden hull was sheathed with copper to protect it from shipworm and biofouling. The ship had a crew that varied over the course of her career from 326 to 345 officers and enlisted sailors. [1] [3]

She was fitted with a three masted full-ship rig. The ship was converted in 1861–1862 with a single marine steam engine that was supplied with a single boiler. It drove a screw propeller and was rated to produce a top speed of 9 knots (17 km/h; 10 mph), [1] from 220 metric horsepower (217  ihp ). [3] The ship could carry up to 148 long tons (150 t), which enabled her to steam for 1,515 nautical miles (2,806 km; 1,743 mi) at 9 knots. As refitted with steam propulsion, she retained the sailing rig for auxiliary use. [1]

The ship's armament varied over the course of her career. As completed, she was armed with a battery of twenty 16 cm (6.3 in) guns; fourteen of these were smoothbore guns in her broadside battery deck, eight guns per side. The remainder were rifled howitzers mounted on her upper deck. She carried four 8 cm (3.1 in) field guns that could be sent ashore with a landing party. A refit in 1870 saw her armament reduced to eight 16 cm smoothbore guns in the battery, though she retained the upper deck howitzers. [1]

Service history

The keel for San Giovanni was laid down in 1848 at the Cantiere della Foce shipyard in Genoa for the Royal Sardinian Navy. Her completed hull was launched the following year. [1] In September 1850, San Giovanni sailed to Tunis in Ottoman Tunisia, arriving there on the 29th. [4]

San Giovanni was sent to Toulon, France, to be converted into a screw-powered steam corvette. By the time she was launched in September 1861, the Italian states had unified as the Kingdom of Italy. [5] [6] Work on the ship continued into 1862. [1]

Third Italian War of Independence

In June 1866, Italy declared war on Austria, as part of the Third Italian War of Independence, which was fought concurrently with the Austro-Prussian War. [7] The Italian fleet commander, Admiral Carlo Pellion di Persano, initially adopted a cautious course of action; he was unwilling to risk battle with the Austrian Navy, despite the fact that the Austrian fleet was much weaker than his own. Persano claimed he was simply waiting on the ironclad ram Affondatore, en route from Britain, but his inaction weakened morale in the fleet, with many of his subordinates openly accusing him of cowardice. [8]

Rear Admiral Wilhelm von Tegetthoff brought the Austrian fleet to Ancona on June 27, in attempt to draw out the Italians. At the time, many of the Italian ships were in disarray; many ships were experiencing various difficulties with their engines or armament. Persano held a council of war aboard the ironclad Principe di Carignano to determine whether he should sortie to engage Tegetthoff, but by that time, the Austrians had withdrawn, making the decision moot. The Minister of the Navy, Agostino Depretis, urged Persano to act and suggested the island of Lissa, to restore Italian confidence after their defeat at the Battle of Custoza the previous month. On 7 July, Persano took the fleet out of Ancona and conducted a sweep into the Adriatic, but encountered no Austrian ships and returned on the 13th. [9]

San Giovanni took part in the Lissa campaign in July 1866 during the Third Italian War of Independence. There, she served in the Second Squadron under Admiral Giovan Battista Albini. [10] Albini was responsible for transporting and landing the Italian army forces that were to seize the island of Lissa though he failed to follow his orders. [11] After the initial attack, Albini held a council of war aboard his flagship that determined further attempts to land troops on the island would be unsuccessful and would only incur further damage to his ships. He sent San Giovanni to inform Persano of his decision to cancel further landing attempts. [12] In the Battle of Lissa that followed the abortive landing operation, Albini failed to support the ironclad fleet under Persano, and as a result, San Giovanni saw no action during the battle. Albini was sacked after the battle for his timidity and failure to follow orders. [13]

Later in the 1860s, San Giovanni was used as a stationary training ship for ship's boys. The navy requested funds to make repairs to the vessel in 1870, but the work was not done at that time. [14] As of October 1871, she was stationed in Venice along with a number of other cruising vessels, including the screw corvette Magenta. [15] Repairs had still not been carried out by 1874, and her condition had deteriorated to the point that it was no longer considered worthwhile to repair her. [14] The ship was laid up in 1875, [2] and by 1878, the Regia Marina had broken her up for scrap. [16]

Notes

  1. 1 2 3 4 5 6 7 San Giovanni.
  2. 1 2 Fraccaroli, p. 336.
  3. 1 2 Österreichs Kämpfe, p. 8 (376).
  4. ↑ Allgemeine Zeitung, p. 4888.
  5. ↑ Metropolitan News, p. 265.
  6. ↑ Fraccaroli, p. 335.
  7. ↑ Sondhaus, p. 1.
  8. ↑ Greene & Massignani, pp. 217–222.
  9. ↑ Wilson, pp. 216–218.
  10. ↑ Sokol, p. 30.
  11. ↑ Wilson, pp. 221–225.
  12. ↑ Österreichs Kämpfe, p. 46 (130).
  13. ↑ Wilson, pp. 232, 234, 251.
  14. 1 2 Camera dei Deputati, p. 15.
  15. ↑ Dupont, p. 427.
  16. ↑ King, p. 236.

Related Research Articles

<span class="mw-page-title-main">Battle of Lissa (1866)</span> Part of the Third Italian War of Independence

The Battle of Lissa took place on 20 July 1866 in the Adriatic Sea near the Dalmatian island of Vis and was a significant victory for an Austrian Empire force over a numerically superior Italian force. It was the first major sea battle between ironclads and one of the last to involve deliberate ramming. The Italian navy fired roughly 1450 shots during the engagement but failed to sink any Austrian ship and lost two ironclads.

Italian ironclad <i>Affondatore</i> Ironclad warship of the Italian Royal Navy

Affondatore was an armoured ram of the Regia Marina, built in the 1860s by Harrison, Millwall, London. Construction commenced in 1863; the ship, despite being incomplete, was brought to Italy during the Third Italian War of Independence. Affondatore, which translates as "Sinker", was initially designed to rely on her ram as her only weapon, but during construction she was also equipped with two 300-pounder guns.

Italian ironclad <i>Re dItalia</i> Ironclad warship of the Italian Royal Navy

Re d'Italia was the lead ship of the Re d'Italia-class armored frigates built in the United States for the Italian Regia Marina in the early 1860s. She was laid down at the William H. Webb Shipyard in New York in November 1861, was launched in April 1863, and was completed a year later in September 1864; the two Re d'Italia-class ships were the only Italian ironclads built in the United States. The ships were broadside ironclads, armed with a battery of six 72-pounder guns and thirty-two 164 mm (6.5 in) guns.

SMS <i>Kaiser</i> (1858) Screw ship of the line, later rebuilt into an ironclad warship, of the Austro-Hungarian Navy

SMS Kaiser was a 92-gun wooden ship of the line of the Austrian Navy, the last vessel of the type, and the only screw-driven example, to be built by the Austrians. She was built by the naval shipyard in Pola; she was laid down in March 1855, was launched in October 1858, and was completed the following year. The ship took part in the Second Schleswig War of 1864, but saw no action during her deployment to the North Sea. Kaiser did see action during the Seven Weeks' War two years later, during which she took part in the Battle of Lissa as the flagship of Anton von Petz, commander of the Austrian 2nd Division. Kaiser engaged several Italian ironclads simultaneously, rammed one—Re di Portogallo—and damaged another—Affondatore—with gunfire. In doing so, she became the only wooden ship of the line to engage an ironclad warship in battle.

<span class="mw-page-title-main">Emilio Faà di Bruno</span>

Emilio Faà di Bruno was an Italian naval officer. He was born in the Kingdom of Sardinia and was a key figure in the unification of Italy and the creation of the Royal Italian Navy. Between 1863 and 1864 he toured the coast of North America, protecting Italian interests and engaging in naval diplomacy. He died at the Battle of Lissa.

Italian ironclad <i>Regina Maria Pia</i> Ironclad warship of the Italian Royal Navy

Regina Maria Pia was the lead ship of the Regina Maria Pia class of ironclad warships built in French shipyards for the Italian Regia Marina in the 1860s. She and her three sister ships were broadside ironclads, mounting a battery of four 203 mm (8 in) and twenty-two 164 mm (6.5 in) guns on the broadside. Regina Maria Pia was laid down in July 1862, was launched in April 1863, and was completed in April 1864.

Italian ironclad <i>San Martino</i> Ironclad warship of the Italian Royal Navy

San Martino was a Regina Maria Pia-class ironclad warship, the second member of her class. She was built for the Italian Regia Marina in the 1860s; like her three sister ships, she was built in France. San Martino was laid down in July 1862, was launched in September 1863, and was completed in November 1864. The ships were broadside ironclads, mounting a battery of four 203 mm (8 in) and twenty-two 164 mm (6.5 in) guns on the broadside.

Italian ironclad <i>Castelfidardo</i> Ironclad warship of the Italian Royal Navy

Castelfidardo was the third of four Regina Maria Pia-class ironclad warships built in French shipyards for the Italian Regia Marina in the 1860s. Castelfidardo was laid down in July 1862, was launched in August 1863, and was completed in May 1864. She and her three sister ships were broadside ironclads, mounting a battery of four 203 mm (8 in) and twenty-two 164 mm (6.5 in) guns on the broadside.

Italian ironclad <i>Ancona</i> Ironclad warship of the Italian Royal Navy

Ancona was an ironclad warship, the last member of the Regina Maria Pia class built in French shipyards for the Italian Regia Marina in the 1860s. Ancona was laid down in August 1862, was launched in October 1864, and completed in April 1866. She and her three sister ships were broadside ironclads, mounting a battery of four 203 mm (8 in) and twenty-two 164 mm (6.5 in) guns on the broadside.

Italian ironclad <i>Re di Portogallo</i> Ironclad warship of the Italian Royal Navy

Re di Portogallo was an ironclad warship built for the Italian Regia Marina in the 1860s, the second and final member of the Re d'Italia class. She was laid down at the William H. Webb Shipyard in New York in December 1861, was launched in August 1863, and was completed a year later in August 1864; the two Re d'Italia-class ships were the only Italian ironclads built in the United States. The ships were broadside ironclads, armed with a battery of six 72-pounder guns and thirty-two 164 mm (6.5 in) guns.

Italian ironclad <i>Principe di Carignano</i> Ironclad warship of the Italian Royal Navy

Principe di Carignano was the lead ship of the Principe di Carignano class of ironclad warships built for the Italian Regia Marina in the 1860s. She was the first ironclad built in Italy; her keel was laid January 1861, her hull was launched in September 1863, and she was completed in June 1865. Principe di Carignano was a broadside ironclad armed with a battery of ten 203 mm (8 in) guns and twelve 164 mm (6.5 in) guns.

Italian ironclad <i>Terribile</i> Ironclad warship of the Italian Royal Navy

Terribile was the first ironclad warship to be built for the Italian Regia Marina, and the second member of the Formidabile class. Terribile and her sister, Formidabile, were both built in France. A broadside ironclad, she was laid down in June 1860, launched in February 1861, and was completed in September that year. She was the first Italian ironclad to enter service and was equipped with four 203 mm (8 in) and sixteen 164 mm (6.5 in) guns.

Italian ironclad <i>Formidabile</i> Ironclad warship of the Italian Royal Navy

Formidabile was the lead ship of the Formidabile-class ironclad warships, the first ships of that type to be built for the newly formed Italian Regia Marina. Formidabile and her sister, Terribile, were both built in France; Formidabile was laid down in December 1860, was launched in October 1861, and was completed in May 1862. She was a broadside ironclad, equipped with four 203 mm (8 in) and sixteen 164 mm (6.5 in) guns.

<i>Regina Maria Pia</i>-class ironclad Ironclad warship class of the Italian Royal Navy

The Regina Maria Pia class was a group of four ironclad warships built for the Italian Regia Marina in the 1860s. The class comprised four ships, Regina Maria Pia, San Martino, Castelfidardo, and Ancona. They were built by French shipyards, since Italian yards were unable to meet the demand of the rapidly expanding Italian fleet. The ships were broadside ironclads and mounted a battery of twenty-six muzzle loading guns.

<i>Re dItalia</i>-class ironclad Ironclad warship class of the Italian Royal Navy

The Re d'Italia class was a pair of ironclad warships built for the Italian Regia Marina in the 1860s. The class comprised two ships, Re d'Italia and Re di Portogallo. The two ships were built in the United States, and were based on the French ironclad Gloire; they were armed with a battery of thirty-eight guns in a broadside arrangement and were protected with 120 mm (4.7 in) of wrought iron plating.

<i>Principe di Carignano</i>-class ironclad Ironclad warship class of the Italian Royal Navy

The Principe di Carignano class was a group of three ironclad warships built for the Italian Regia Marina in the 1860s. The class comprised the ships Principe di Carignano, Messina, and Conte Verde. Originally ordered as wooden frigates, they were the first ironclads to be built in Italy, but the inexperience of the Italian shipyards and the redesign process produced lengthy construction times, such that only the lead ship was completed in time to see action during the Third Italian War of Independence in 1866. The first two ships were protected by a complete belt of wrought iron plating that was 121 mm (4.75 in) thick, while Conte Verde only received a partial iron belt.

<i>Formidabile</i>-class ironclad Ironclad warship class of the Italian Royal Navy

The Formidabile class was a pair of ironclad warships built for the Italian Regia Marina in the 1860s. The class comprised two ships, Formidabile and Terribile. Initially ordered for the Regia Marina Sarda, by the time they were completed the Kingdom of Sardinia had unified the rest of the Italian states and created the Regia Marina. They were the first ironclads built for the Italian fleet. Wooden-hulled vessels plated with 4.3 inches (109 mm) of wrought iron, they were armed with a battery of twenty guns in a broadside arrangement.

SMS <i>Prinz Eugen</i> (1862) Ironclad warship of the Austro-Hungarian Navy

SMS Prinz Eugen was the second member of the Kaiser Max class built for the Austrian Navy in the 1860s. Her keel was laid in October 1861 at the Stabilimento Tecnico Triestino shipyard; she was launched in June 1862, and was completed in March 1863. She carried her main battery—composed of sixteen 48-pounder guns and fifteen 24-pounders—in a traditional broadside arrangement, protected by an armored belt that was 110 mm (4.3 in) thick.

Italian corvette <i>Etna</i>

Etna was a screw corvette of the Italian Regia Marina, originally ordered by the Real Marina of the Kingdom of the Two Sicilies, but completed after the unification of Italy. The ship had a relatively uneventful career, primarily cruising in the Mediterranean Sea in the 1860s, although she also made a deployment to South America from 1869 to 1871. She was laid up in 1875, but her ultimate fate is unknown.

References

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.