The March 2-4-0 was an experimental six-wheeled Formula One racing car built by the March Engineering company of Bicester, UK. It was constructed in late 1976 and tested in early 1977.
The car followed on from the successful use by Tyrrell Racing of a six-wheeled car, the Tyrrell P34, in Formula One racing. However, the engineering concept behind the 2-4-0 was quite different.
The front wheels of an open-wheeled F1 car generate aerodynamic drag. The thinking behind the Tyrrell P34 was that this drag effect could be reduced by using smaller diameter tyres at the front. At the time, conventional F1 front wheels would measure around 16" (40cm) diameter but Tyrrell planned to use just 10" (25cm) diameter wheels. The corresponding loss of front-end grip was overcome by incorporating two front wheels per side thus actually increasing grip as well as decreasing drag. The design incorporated a system whereby all four front wheels could steer the car.
The P34 was reasonably successful with the two cars taking a memorable 1–2 in the 1976 Swedish Grand Prix. The Tyrrell team also finished 3rd and 4th overall in the championship. The car was less successful in 1977 however and the idea was dropped. Reasons given were that although Goodyear had manufactured special tyres for the car, the tyre company had failed to match the development work on them compared to the normal sized tyres used by other teams. With all four front wheels steering the car, Tyrrell also found that the P34's complex four-wheel front suspension assembly added a lot of weight to the car.
At March Engineering in Bicester, designer Robin Herd had watched the P34 experiment closely and, by late 1976, had come to the conclusion that the 'four front wheels' concept might have been a blind alley. In his assessment, the improved aerodynamics at the front were largely negated by the rear tyres which at 24" (60cm) diameter would still have accounted for 30 to 40% of the car's total drag. He also felt that with a modern rear wheel drive F1 car, the extra grip could be employed more usefully for the driven wheels.
With this in mind, Herd drew up plans for a six-wheeled car with four driven wheels at the rear and all of the wheels the same 16" diameter. His theory was that with all six tyres the same size as the regular F1 front tyre, the car would not only be slimmer than normal F1 cars but would possess improved aerodynamic performance at the rear with much cleaner air passing over the wing. Four driven wheels would also mean better traction and, unlike the Tyrrell, there would be no problem with tyre development since the car would use exactly the same rubber as a conventional F1 car.
Herd called this concept '2-4-0', following the Whyte notation used to describe railway rolling stock: two wheels leading, four driven wheels, zero trailing wheels.
Design, construction & development
With the apparent technical advantages of this concept laid out, Max Mosley (Herd's partner at March Cars) gave the go-ahead for a prototype to be built. Mosley noted that the P34 had generated a lot of additional publicity for Tyrrell and, aside from the technical merits, believed a March six-wheeler would be an attractive package to present to potential sponsors.
Unfortunately, the March team was at something of a low point financially during 1976/77 and the development costs of an all-new six-wheel car would be high. As a compromise measure, a 1976-design Cosworth DFV-powered March 761 was adapted by team mechanic Wayne Eckersley in a quiet corner of the Bicester factory. Existing parts from the factory stores were used wherever possible.
A key feature of a car with four driven wheels at the rear would be the transmission. An ingenious gearbox design was required to minimise any frictional power losses. It would also have to be stronger (and hence heavier) to counteract the higher torsional and flexural stresses that the close-coupled four-wheel-drive system would generate.
Herd's original design for the gearbox casing recognised these factors and specified a series of strengthening ribs to counteract the additional loading. However, at some point in development it was decided that the casting would be very complex and expensive to produce. By way of a cost-cutting measure, some of the ribs were duly removed from the drawing.
In fact, the design utilised a standard Hewland F1 gearbox for the first axle. To this, the new casing, gears and an extended pinion for the second axle were fitted. Practically, this meant that any 761 chassis could be easily adapted should the concept prove workable.
Once the 2-4-0 was partially built, the press were invited to the factory in late November 1976 for a viewing of the hitherto 'secret' project. The unveiling generated a huge amount of interest with articles in several motor sport magazines plus a photograph on the cover of the following week's Autosport magazine (dated 2 December 1976).
Simultaneously, the company also outlined plans for a full running demonstration and developmental testing at Silverstone circuit scheduled for a fortnight later.
Testing
The first test took place at Silverstone in late 1976. Unfortunately, on the initial lap the gearbox casing flexed and the gears became unmeshed. No immediate solution could be found and so the rear crown wheel and pinion were removed for the rest of the day's testing. Effectively the 2-4-0 had become a two-wheel drive car again. Fortunately for March, it was a wet day at the circuit and the driver Howden Ganley could not push the car too fast. Consequently, the test was reported as a success by the media.
The problems on the first lap highlighted the fact that the car needed a new, stronger gearbox casing and a serious development program. Unable to afford the time and resources that this would require, the 2-4-0 project was de-prioritised by the company.
In February 1977, the car — now fitted with a stronger gearbox — ran again at Silverstone with driver Ian Scheckter at the wheel. Although it was another wet day, the car was run up and down the Hangar Straight and, with four driven wheels, Scheckter reported that the traction was 'incredible'. Additionally, the events of the day again made Autosport magazine's front page (dated 10 February 1977).
But this was the end of 2-4-0's F1 development history. On its reappearance at the Belgium GP in June, the converted 761 chassis had been reconfigured as a conventional four-wheeler.
Myth of appearance at the Brazilian GP
In August 2002 an article appeared on the 8W website that claimed, on the basis of an incorrectly identified photograph, that the 2-4-0 may have appeared in practice for the 1977 Brazilian Grand Prix at the end of January. The photograph in question actually showed the car testing at Silverstone in February 1977 and it is clear from contemporary reports of the Grand Prix that the 2-4-0 was not present. The author of the 8W article has now corrected the error but not before it was used as a source for a number of other websites.
Hill climbing
In 1979 the 2-4-0 concept was revived by British Hillclimb specialist Roy Lane. Lane had bought a March 771 chassis and with Robin Herd's blessing was loaned the improved 2-4-0 transmission unit. The fact that the 2-4-0 was originally an inexpensive workshop conversion of the standard March F1 chassis meant that Lane was easily able to fit the unit to his car.
Taking advantage of four-wheel traction, Lane won several British hill-climbing events in the 771/2-4-0 that year with the first win at Wiscombe Park in May. However, over the season the car proved troublesome and Lane eventually switched back to the four-wheel configuration.
Legacy
Despite only limited success in short duration racing events, the 2-4-0 concept was never disproven. It is possible that if a weight-shedding program had been pursued (possibly using stronger and lighter materials) and the car's suspect handling improved, the 2-4-0 could have proved successful in F1. The concept would certainly have adapted well to ground effect which was the coming technology in grand prix racing.
The Williams team seem to have agreed with Herd's theory because they built and tested two 2-4-0–style six-wheeled cars – designated the FW07D and FW08B. However, any hopes of seeing a 2-4-0–style race car compete in a grand prix were dashed when the FIA banned all four-wheel drive systems in this category. The FW08B remains on display in the Williams's factory museum.
The March 2-4-0 story was not without a silver lining for the company that built it. As Max Mosley had surmised, the car was indeed a huge publicity magnet. Additionally, significant income was generated for the team when the Scalextric company purchased the rights to produce and market a best-selling 1/32 scale slot-racing replica.
The McLaren F1 is a sports car designed and manufactured by British automobile manufacturer McLaren Cars and powered by the BMW S70/2 V12 engine, of which a limited number was produced. The original concept was conceived by Gordon Murray, who successfully convinced Ron Dennis to back the project and hired car designer Peter Stevens to design the exterior and interior of the car. On 31 March 1998, the XP5 prototype with a modified rev limiter set the Guinness World Record for the world's fastest production car, reaching 240.1 mph (386.4 km/h), surpassing the modified Jaguar XJ220's 218.3 mph (351 km/h) record from 1993.
The Tyrrell P34, commonly known as the "six-wheeler", was a Formula One (F1) race car designed by Derek Gardner, Tyrrell's chief designer. The car used four specially manufactured 10-inch diameter (254 mm) wheels and tyres at the front, with two ordinary-sized wheels at the back. Along with the Brabham BT46B "fancar" developed in 1978, the six-wheeled Tyrrell was one of the most radical entries ever to succeed in F1 competition and has been called the most recognisable design in the history of world motorsports.
A Formula One car or F1 car is a single-seat, open-cockpit, open-wheel formula racing car with substantial front and rear wings, and an engine positioned behind the driver, intended to be used in competition at Formula One racing events. The regulations governing the cars are unique to the championship and specify that cars must be constructed by the racing teams themselves, though the design and manufacture can be outsourced. Formula One drivers experience peak cornering forces of up to six lateral g.
Front-wheel drive (FWD) is a form of engine and transmission layout used in motor vehicles, in which the engine drives the front wheels only. Most modern front-wheel-drive vehicles feature a transverse engine, rather than the conventional longitudinal engine arrangement generally found in rear-wheel-drive and four-wheel-drive vehicles.
The 1976 Formula One season was the 30th season of FIA Formula One motor racing. It featured the 1976 World Championship of Drivers and the 1976 International Cup for Formula 1 Manufacturers. The two titles were contested over a sixteen race series which commenced on 25 January and ended on 24 October. Two non-championship races were also held during the 1976 season. In an extraordinarily political and dramatic season, the Drivers' Championship went to McLaren driver James Hunt by one point from Ferrari's defending champion Niki Lauda, although Ferrari took the Manufacturers' trophy.
The Ferrari 599 GTB Fiorano is a grand tourer produced by the Italian automobile manufacturer Ferrari. It served as the brand's front-engined, two-seat model, replacing the 575M Maranello in 2006 as a 2007 model, and was later replaced for the 2013 model year by the F12berlinetta.
March Engineering was a Formula One constructor and manufacturer of customer racing cars from the United Kingdom. Although only moderately successful in Grand Prix competition, March racing cars enjoyed much better success in other categories of competition, including Formula Two, Formula Three, IndyCar and IMSA GTP sportscar racing.
Robert Kenneth Tyrrell was a British Formula Two racing driver and the founder of the Tyrrell Formula One constructor.
The Panther 6 was a British six-wheel convertible produced by Panther in 1977.
The Brabham BT46 is a Formula One racing car designed by Gordon Murray for the Brabham team, owned by Bernie Ecclestone, for the 1978 Formula One season. The car featured several radical design elements, one of which was the use of flat panel heat exchangers on the bodywork of the car to replace conventional water and oil radiators. It was removed before the car's race debut, never to be seen again. The cars, powered by a flat-12 Alfa Romeo engine, raced competitively with modified nose-mounted radiators for most of the year, driven by Niki Lauda and John Watson, winning one race in this form and scoring sufficient points for the team to finish third in the constructors' championship.
The Ferrari 312T was a Ferrari Formula One car design, based on the 312B3 from 1974. In various versions, it was used from 1975 until 1980. It was designed by Mauro Forghieri for the 1975 season, and was an uncomplicated and clean design that responded well to mechanical upgrades.
The Clio Renault Sport is a hot hatch produced by Renault Sport since 1998, the high-performance division of French automaker, Renault. It is based on the Clio supermini.
The Ferrari F399 was the car with which the Ferrari team competed in the 1999 Formula One World Championship. The chassis was designed by Rory Byrne, Giorgio Ascanelli, Aldo Costa, Marco Fainello, Willem Toet, and Nikolas Tombazis, with Ross Brawn playing a vital role in leading the production of the car as the team's technical director and Paolo Martinelli assisted by Giles Simon leading the engine design and operations.
The Ferrari 640 was the Formula One racing car with which the Ferrari team competed in the 1989 Formula One World Championship. It was driven by Britain's Nigel Mansell, in his first season with the team, and Austria's Gerhard Berger, winning three races between them. A prototype version known as the 639 shares some features of the early version of the 640. This prototype was tested in 1988 prior to the introduction of the early version of the 640 in 1989. Both the early and late versions of the 640 were entered with the competition title F1-89. The 639 did not receive a competition title due to its status as a prototype model.
Four-wheel drive (4WD) has only been tried a handful of times in Formula One. In the World Championship era since 1950, only eight such cars are known to have been built.
The Williams FW08 was a Formula One car designed by Frank Dernie, which debuted at the 1982 Belgian Grand Prix held at the Zolder circuit. An evolution of the FW07 that it replaced, the car was used by Finnish driver Keke Rosberg to win the 1982 World Drivers' Championship.
The March 701 is a Formula One racing car model, designed by Robin Herd with Peter Wright, and built by March Engineering. The 701 was March's first Formula One design – following their one-off March 693P Formula Three prototype of 1969 – and was designed and built in only three months. The March 701 made its race debut a month after its public unveiling, at the 1970 South African Grand Prix. In total, eleven 701s were constructed, with March supplying many privateer entrants as well as their own works team. The 701's career started well, March drivers taking three wins and three pole positions from the car's first four race entries, but lack of development through the 1970 Formula One season resulted in increasingly poor results as the year wore on. The 701 was superseded by the March 711 in 1971, and made its last World Championship race appearance at the 1971 Italian Grand Prix.
The Ford Seattle-ite XXI was a 3/8 scale concept car designed by Alex Tremulis and displayed on 20 April 1962 on the Ford stand at the Seattle World's Fair.
The 2013 British Grand Prix was a Formula One motor race held at the Silverstone Circuit in Silverstone, England, United Kingdom, on 30 June 2013 before 120,000 spectators. It was the eighth round of the 2013 Formula One World Championship and the 64th British Grand Prix to be held as part of the series. Mercedes driver Nico Rosberg won the 52-lap race starting from second position. Mark Webber of the Red Bull team finished second and Fernando Alonso took third in a Ferrari.
The Audi R8 LMS Cup was a one-make sports car racing series by Audi based in Asia. Audi R8 LMS Cup cars were based on the Audi R8 LMS (GT3).
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
