Metacentric height

Last updated October 10, 2024

Ship stability diagram showing centre of gravity (G), centre of buoyancy (B), and metacentre (M) with ship upright and heeled over to one side.
As long as the load of a ship remains stable, G is fixed (relative to the ship). For small angles, M can also be considered to be fixed, while B moves as the ship heels. MetacentricHeight.svg — Ship stability diagram showing *centre of gravity* (G), *centre of buoyancy* (B), and *metacentre* (M) with ship upright and heeled over to one side.
As long as the load of a ship remains stable, G is fixed (relative to the ship). For small angles, M can also be considered to be fixed, while B moves as the ship heels.

The metacentric height (GM) is a measurement of the initial static stability of a floating body.^[1] It is calculated as the distance between the centre of gravity of a ship and its metacentre . A larger metacentric height implies greater initial stability against overturning. The metacentric height also influences the natural period of rolling of a hull, with very large metacentric heights being associated with shorter periods of roll which are uncomfortable for passengers. Hence, a sufficiently, but not excessively, high metacentric height is considered ideal for passenger ships.

Different centres

Initially the second moment of area increases as the surface area increases, increasing BM, so Mph moves to the opposite side, thus increasing the stability arm. When the deck is flooded, the stability arm rapidly decreases. GNfiguur.PNG — Initially the second moment of area increases as the surface area increases, increasing BM, so Mφ moves to the opposite side, thus increasing the stability arm. When the deck is flooded, the stability arm rapidly decreases.

The centre of buoyancy is at the centre of mass of the volume of water that the hull displaces. This point is referred to as B in naval architecture. The centre of gravity of the ship is commonly denoted as point G or CG. When a ship is at equilibrium, the centre of buoyancy is vertically in line with the centre of gravity of the ship.^[1]

The metacentre is the point where the lines intersect (at angle φ) of the upward force of buoyancy of φ ± dφ. When the ship is vertical, the metacentre lies above the centre of gravity and so moves in the opposite direction of heel as the ship rolls. This distance is also abbreviated as GM. As the ship heels over, the centre of gravity generally remains fixed with respect to the ship because it just depends on the position of the ship's weight and cargo, but the surface area increases, increasing BMφ. Work must be done to roll a stable hull. This is converted to potential energy by raising the centre of mass of the hull with respect to the water level or by lowering the centre of buoyancy or both. This potential energy will be released in order to right the hull and the stable attitude will be where it has the least magnitude. It is the interplay of potential and kinetic energy that results in the ship having a natural rolling frequency. For small angles, the metacentre, Mφ, moves with a lateral component so it is no longer directly over the centre of mass.^[2]

The righting couple on the ship is proportional to the horizontal distance between two equal forces. These are gravity acting downwards at the centre of mass and the same magnitude force acting upwards through the centre of buoyancy, and through the metacentre above it. The righting couple is proportional to the metacentric height multiplied by the sine of the angle of heel, hence the importance of metacentric height to stability. As the hull rights, work is done either by its centre of mass falling, or by water falling to accommodate a rising centre of buoyancy, or both.

For example, when a perfectly cylindrical hull rolls, the centre of buoyancy stays on the axis of the cylinder at the same depth. However, if the centre of mass is below the axis, it will move to one side and rise, creating potential energy. Conversely if a hull having a perfectly rectangular cross section has its centre of mass at the water line, the centre of mass stays at the same height, but the centre of buoyancy goes down as the hull heels, again storing potential energy.

When setting a common reference for the centres, the molded (within the plate or planking) line of the keel (K) is generally chosen; thus, the reference heights are:

KB – to Centre of Buoyancy
KG – to Centre of Gravity
KMT – to Transverse Metacentre

Metacentre

When a ship heels (rolls sideways), the centre of buoyancy of the ship moves laterally. It might also move up or down with respect to the water line. The point at which a vertical line through the heeled centre of buoyancy crosses the line through the original, vertical centre of buoyancy is the metacentre. The metacentre remains directly above the centre of buoyancy by definition.

In the diagram above, the two Bs show the centres of buoyancy of a ship in the upright and heeled conditions. The metacentre, M, is considered to be fixed relative to the ship for small angles of heel; however, at larger angles the metacentre can no longer be considered fixed, and its actual location must be found to calculate the ship's stability.

It can be calculated using the formulae:

$KM=KB+BM$
$BM={\frac {I}{V}}\$

Where KB is the centre of buoyancy (height above the keel), I is the second moment of area of the waterplane around the rotation axis in metres⁴, and V is the volume of displacement in metres³. KM is the distance from the keel to the metacentre.^[3]

Stable floating objects have a natural rolling frequency, just like a weight on a spring, where the frequency is increased as the spring gets stiffer. In a boat, the equivalent of the spring stiffness is the distance called "GM" or "metacentric height", being the distance between two points: "G" the centre of gravity of the boat and "M", which is a point called the metacentre.

Metacentre is determined by the ratio between the inertia resistance of the boat and the volume of the boat. (The inertia resistance is a quantified description of how the waterline width of the boat resists overturning.) Wide and shallow hulls have high transverse metacentres, whilst narrow and deep hulls have low metacentres . Ignoring the ballast, wide and shallow means that the ship is very quick to roll, and narrow and deep means that the ship is very hard to overturn and is stiff.

"G", is the center of gravity. "GM", the stiffness parameter of a boat, can be lengthened by lowering the center of gravity or changing the hull form (and thus changing the volume displaced and second moment of area of the waterplane) or both.

An ideal boat strikes a balance. Very tender boats with very slow roll periods are at risk of overturning, but are comfortable for passengers. However, vessels with a higher metacentric height are "excessively stable" with a short roll period resulting in high accelerations at the deck level.

Sailing yachts, especially racing yachts, are designed to be stiff, meaning the distance between the centre of mass and the metacentre is very large in order to resist the heeling effect of the wind on the sails. In such vessels, the rolling motion is not uncomfortable because of the moment of inertia of the tall mast and the aerodynamic damping of the sails.

Righting arm

The metacentric height is an approximation for the vessel stability at a small angle (0-15 degrees) of heel. Beyond that range, the stability of the vessel is dominated by what is known as a righting moment. Depending on the geometry of the hull, naval architects must iteratively calculate the center of buoyancy at increasing angles of heel. They then calculate the righting moment at this angle, which is determined using the equation:

$RM=GZ\cdot \Delta$

Where RM is the righting moment, GZ is the righting arm and $Δ$ is the displacement. Because the vessel displacement is constant, common practice is to simply graph the righting arm vs the angle of heel. The righting arm (known also as GZ — see diagram): the horizontal distance between the lines of buoyancy and gravity.^[2]

$GZ=GM\cdot \sin \phi$ ^[1] at small angles of heel

There are several important factors that must be determined with regards to righting arm/moment. These are known as the maximum righting arm/moment, the point of deck immersion, the downflooding angle, and the point of vanishing stability. The maximum righting moment is the maximum moment that could be applied to the vessel without causing it to capsize. The point of deck immersion is the angle at which the main deck will first encounter the sea. Similarly, the downflooding angle is the angle at which water will be able to flood deeper into the vessel. Finally, the point of vanishing stability is a point of unstable equilibrium. Any heel lesser than this angle will allow the vessel to right itself, while any heel greater than this angle will cause a negative righting moment (or heeling moment) and force the vessel to continue to roll over. When a vessel reaches a heel equal to its point of vanishing stability, any external force will cause the vessel to capsize.

Sailing vessels are designed to operate with a higher degree of heel than motorized vessels and the righting moment at extreme angles is of high importance.

Monohulled sailing vessels should be designed to have a positive righting arm (the limit of positive stability) to at least 120° of heel,^[4] although many sailing yachts have stability limits down to 90° (mast parallel to the water surface). As the displacement of the hull at any particular degree of list is not proportional, calculations can be difficult, and the concept was not introduced formally into naval architecture until about 1970.^[5]

Stability

GM and rolling period

The metacentre has a direct relationship with a ship's rolling period. A ship with a small GM will be "tender" - have a long roll period. An excessively low or negative GM increases the risk of a ship capsizing in rough weather, for example HMS Captain or the Vasa. It also puts the vessel at risk of potential for large angles of heel if the cargo or ballast shifts, such as with the Cougar Ace. A ship with low GM is less safe if damaged and partially flooded because the lower metacentric height leaves less safety margin. For this reason, maritime regulatory agencies such as the International Maritime Organization specify minimum safety margins for seagoing vessels. A larger metacentric height on the other hand can cause a vessel to be too "stiff"; excessive stability is uncomfortable for passengers and crew. This is because the stiff vessel quickly responds to the sea as it attempts to assume the slope of the wave. An overly stiff vessel rolls with a short period and high amplitude which results in high angular acceleration. This increases the risk of damage to the ship and to cargo and may cause excessive roll in special circumstances where eigenperiod of wave coincide with eigenperiod of ship roll. Roll damping by bilge keels of sufficient size will reduce the hazard. Criteria for this dynamic stability effect remain to be developed. In contrast, a "tender" ship lags behind the motion of the waves and tends to roll at lesser amplitudes. A passenger ship will typically have a long rolling period for comfort, perhaps 12 seconds while a tanker or freighter might have a rolling period of 6 to 8 seconds.

The period of roll can be estimated from the following equation:^[1]

$T={\frac {2\pi \,(a_{44}+k)}{\sqrt {g{\overline {GM}}}}}\$

where g is the gravitational acceleration, a44 is the added radius of gyration and k is the radius of gyration about the longitudinal axis through the centre of gravity and ${\overline {GM}}$ is the stability index.

Damaged stability

If a ship floods, the loss of stability is caused by the increase in KB, the centre of buoyancy, and the loss of waterplane area - thus a loss of the waterplane moment of inertia - which decreases the metacentric height.^[1] This additional mass will also reduce freeboard (distance from water to the deck) and the ship's downflooding angle (minimum angle of heel at which water will be able to flow into the hull). The range of positive stability will be reduced to the angle of down flooding resulting in a reduced righting lever. When the vessel is inclined, the fluid in the flooded volume will move to the lower side, shifting its centre of gravity toward the list, further extending the heeling force. This is known as the free surface effect.

Free surface effect

In tanks or spaces that are partially filled with a fluid or semi-fluid (fish, ice, or grain for example) as the tank is inclined the surface of the liquid, or semi-fluid, stays level. This results in a displacement of the centre of gravity of the tank or space relative to the overall centre of gravity. The effect is similar to that of carrying a large flat tray of water. When an edge is tipped, the water rushes to that side, which exacerbates the tip even further.

The significance of this effect is proportional to the cube of the width of the tank or compartment, so two baffles separating the area into thirds will reduce the displacement of the centre of gravity of the fluid by a factor of 9. This is of significance in ship fuel tanks or ballast tanks, tanker cargo tanks, and in flooded or partially flooded compartments of damaged ships. Another worrying feature of free surface effect is that a positive feedback loop can be established, in which the period of the roll is equal or almost equal to the period of the motion of the centre of gravity in the fluid, resulting in each roll increasing in magnitude until the loop is broken or the ship capsizes.

This has been significant in historic capsizes, most notably the MS Herald of Free Enterprise and the MS Estonia.

Transverse and longitudinal metacentric heights

There is also a similar consideration in the movement of the metacentre forward and aft as a ship pitches. Metacentres are usually separately calculated for transverse (side to side) rolling motion and for lengthwise longitudinal pitching motion. These are variously known as ${\overline {GM_{T}}}$ and ${\overline {GM_{L}}}$ , GM(t) and GM(l), or sometimes GMt and GMl .

Technically, there are different metacentric heights for any combination of pitch and roll motion, depending on the moment of inertia of the waterplane area of the ship around the axis of rotation under consideration, but they are normally only calculated and stated as specific values for the limiting pure pitch and roll motion.

Measurement

The metacentric height is normally estimated during the design of a ship but can be determined by an inclining test once it has been built. This can also be done when a ship or offshore floating platform is in service. It can be calculated by theoretical formulas based on the shape of the structure.

The angle(s) obtained during the inclining experiment are directly related to GM. By means of the inclining experiment, the 'as-built' centre of gravity can be found; obtaining GM and KM by experiment measurement (by means of pendulum swing measurements and draft readings), the centre of gravity KG can be found. So KM and GM become the known variables during inclining and KG is the wanted calculated variable (KG = KM-GM)

Related Research Articles

A hull is the watertight body of a ship, boat, submarine, or flying boat. The hull may open at the top, or it may be fully or partially covered with a deck. Atop the deck may be a deckhouse and other superstructures, such as a funnel, derrick, or mast. The line where the hull meets the water surface is called the waterline.

A multihull is a boat or ship with more than one hull, whereas a vessel with a single hull is a monohull. The most common multihulls are catamarans, and trimarans. There are other types, with four or more hulls, but such examples are very rare and tend to be specialised for particular functions.

Flight dynamics is the science of air vehicle orientation and control in three dimensions. The three critical flight dynamics parameters are the angles of rotation in three dimensions about the vehicle's center of gravity (cg), known as pitch, roll and yaw. These are collectively known as aircraft attitude, often principally relative to the atmospheric frame in normal flight, but also relative to terrain during takeoff or landing, or when operating at low elevation. The concept of attitude is not specific to fixed-wing aircraft, but also extends to rotary aircraft such as helicopters, and dirigibles, where the flight dynamics involved in establishing and controlling attitude are entirely different.

<span class="mw-page-title-main">Buoyancy</span> Upward force that opposes the weight of an object immersed in fluid

Buoyancy, or upthrust is a net upward force exerted by a fluid that opposes the weight of a partially or fully immersed object. In a column of fluid, pressure increases with depth as a result of the weight of the overlying fluid. Thus, the pressure at the bottom of a column of fluid is greater than at the top of the column. Similarly, the pressure at the bottom of an object submerged in a fluid is greater than at the top of the object. The pressure difference results in a net upward force on the object. The magnitude of the force is proportional to the pressure difference, and is equivalent to the weight of the fluid that would otherwise occupy the submerged volume of the object, i.e. the displaced fluid.

Automobile handling and vehicle handling are descriptions of the way a wheeled vehicle responds and reacts to the inputs of a driver, as well as how it moves along a track or road. It is commonly judged by how a vehicle performs particularly during cornering, acceleration, and braking as well as on the vehicle's directional stability when moving in steady state condition.

Capsizing or keeling over occurs when a boat or ship is rolled on its side or further by wave action, instability or wind force beyond the angle of positive static stability or it is upside down in the water. The act of recovering a vessel from a capsize is called righting. Capsize may result from broaching, knockdown, loss of stability due to cargo shifting or flooding, or in high speed boats, from turning too fast.

Ballast is weight placed low in ships to lower their centre of gravity, which increases stability. Insufficiently ballasted boats tend to tip or heel excessively in high winds. Too much heel may result in the vessel filling with water and/or capsizing. If a sailing vessel needs to voyage without cargo, then ballast of little or no value will be loaded to keep the vessel upright. Some or all of this ballast will then be discarded when cargo is loaded.

A ballast tank is a compartment within a boat, ship or other floating structure that holds water, which is used as ballast to provide hydrostatic stability for a vessel, to reduce or control buoyancy, as in a submarine, to correct trim or list, to provide a more even load distribution along the hull to reduce structural hogging or sagging stresses, or to increase draft, as in a semi-submersible vessel or platform, or a SWATH, to improve seakeeping. Using water in a tank provides easier weight adjustment than the stone or iron ballast used in older vessels, and makes it easy for the crew to reduce a vessel's draft when it enters shallower water, by temporarily pumping out ballast. Airships use ballast tanks mainly to control buoyancy and correct trim.

The free surface effect is a mechanism which can cause a watercraft to become unstable and capsize.

In the field of ship design and design of other floating structures, a response amplitude operator (RAO) is an engineering statistic, or set of such statistics, that are used to determine the likely behavior of a ship when operating at sea. Known by the acronym of RAO, response amplitude operators are usually obtained from models of proposed ship designs tested in a model basin, or from running specialized CFD computer programs, often both. RAOs are usually calculated for all ship motions and for all wave headings.

<span class="mw-page-title-main">Bicycle and motorcycle dynamics</span> Science behind the motion of bicycles and motorcycles

Bicycle and motorcycle dynamics is the science of the motion of bicycles and motorcycles and their components, due to the forces acting on them. Dynamics falls under a branch of physics known as classical mechanics. Bike motions of interest include balancing, steering, braking, accelerating, suspension activation, and vibration. The study of these motions began in the late 19th century and continues today.

Ship motions are defined by the six degrees of freedom that a ship, boat, or other watercraft, or indeed any conveyance, can experience.

<span class="mw-page-title-main">Stability derivatives</span>

Stability derivatives, and also control derivatives, are measures of how particular forces and moments on an aircraft change as other parameters related to stability change. For a defined "trim" flight condition, changes and oscillations occur in these parameters. Equations of motion are used to analyze these changes and oscillations. Stability and control derivatives are used to linearize (simplify) these equations of motion so the stability of the vehicle can be more readily analyzed.

An inclining test is a test performed on a ship to determine its stability, lightship weight and the coordinates of its center of gravity. The test is applied to newly constructed ships greater than 24m in length, and to ships altered in ways that could affect stability. Inclining test procedures are specified by the International Maritime Organization and other international associations.

Angle of loll is the state of a ship that is unstable when upright and therefore takes on an angle of heel to either port or starboard.

Tomozuru (友鶴) was one of four Chidori-class torpedo boats of the Imperial Japanese Navy (IJN). It capsized in a storm on 12 March 1934, shortly after its completion. This incident forced the IJN to review the stability of all recently completed, under construction and planned ships. It was salvaged and put back into service after extensive modifications. During World War II, the Tomozuru fought in the Battle of the Philippines and in the Dutch East Indies campaign as an escort, and it continued to play that role for the rest of the war.

Ship stability is an area of naval architecture and ship design that deals with how a ship behaves at sea, both in still water and in waves, whether intact or damaged. Stability calculations focus on centers of gravity, centers of buoyancy, the metacenters of vessels, and on how these interact.

The angle of list is the degree to which a vessel heels to either port or starboard at equilibrium—with no external forces acting upon it. If a listing ship goes beyond the point where a righting moment will keep it afloat, it will capsize and potentially sink.

Flare is the angle at which a ship's hull plate or planking departs from the vertical in an outward direction with increasing height. A flared hull typically has a deck area larger than its cross-sectional area at the waterline. Most vessels have some degree of flare above the waterline, which is especially true for sea-going ships. Advantages of hull flare can include improvements in stability, splash and wash suppression, and dockside utility. Flare can also induce instability when it raises the center of gravity and lateral torque moment of a vessel too much.

Crank is a condition in which a ship heels abnormally, and recovers slowly under the action of the wind. If a ship makes long, slow rolls and takes time resuming a vertical position, it is referred to as crank, cranky, crank-sided, tender, or tender-sided. If the ship snaps back to its vertical position when heeled, it is called ʻstiff.ʼ Stiffness refers to a ship's power to stand up to her canvas, and will offer great resistance to inclination from the upright, when under sail. Although stiff is considered good in the case of many ships, there are extreme cases in which the vessel will be too stiff and resist the tendency to heel under wind pressure, which may cause damage to masts, rigging, and structure. According to Arthur Nelson, “most new Tudor ships were affected slightly on completion, one way or the other."

References

1 2 3 4 5 Comstock, John (1967). Principles of Naval Architecture. New York: Society of Naval Architects and Marine Engineers. p. 827. ISBN 9997462556.
1 2 Harland, John (1984). Seamanship in the age of sail . London: Conway Maritime Press. pp. 43. ISBN 0-85177-179-3.
↑ Ship Stability. Kemp & Young. ISBN 0-85309-042-4
↑ Rousmaniere, John, ed. (1987). Desirable and Undesirable Characteristics of Offshore Yachts . New York, London: W.W.Norton. pp. 310. ISBN 0-393-03311-2.
↑ U.S. Coast Guard Technical computer program support accessed 20 December 2006.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[SNAME-1] 1 2 3 4 5 Comstock, John (1967). Principles of Naval Architecture. New York: Society of Naval Architects and Marine Engineers. p. 827. ISBN 9997462556.

[harland-2] 1 2 Harland, John (1984). Seamanship in the age of sail . London: Conway Maritime Press. pp. 43. ISBN 0-85177-179-3.

[3] Ship Stability. Kemp & Young. ISBN 0-85309-042-4

[rousmaniere-4] Rousmaniere, John, ed. (1987). Desirable and Undesirable Characteristics of Offshore Yachts . New York, London: W.W.Norton. pp. 310. ISBN 0-393-03311-2.

[5] U.S. Coast Guard Technical computer program support accessed 20 December 2006.

[1]

[2]

[3]

[4]

[5]