Micro-encapsulation

Last updated

Microencapsulation is a process in which tiny particles or droplets are surrounded by a coating to give small capsules, with useful properties. [1] [2] In general, it is used to incorporate food ingredients, [3] enzymes, cells or other materials on a micro metric scale. Microencapsulation can also be used to enclose solids, liquids, or gases inside a micrometric wall made of hard or soft soluble film, in order to reduce dosing frequency and prevent the degradation of pharmaceuticals. [4]

Contents

In its simplest form, a microcapsule is a small sphere comprising a near-uniform wall enclosing some material. The enclosed material in the microcapsule is referred to as the core, internal phase, or fill, whereas the wall is sometimes called a shell, coating, or membrane. Some materials like lipids and polymers, such as alginate, may be used as a mixture to trap the material of interest inside. Most microcapsules have pores with diameters between a few nanometers and a few micrometers. Materials generally used for coating are:

The definition has been expanded, and includes most foods, where the encapsulation of flavors is the most common. [5] The technique of microencapsulation depends on the physical and chemical properties of the material to be encapsulated. [6]

Many microcapsules however bear little resemblance to these simple spheres. The core may be a crystal, a jagged adsorbent particle, an emulsion, a Pickering emulsion, a suspension of solids, or a suspension of smaller microcapsules. The microcapsule even may have multiple walls.

IUPAC definition

Microcapsule: Hollow microparticle composed of a solid shell surrounding a
core-forming space available to permanently or temporarily entrapped substances.

Note: The substances can be flavour compounds, pharmaceuticals, pesticides, dyes, or similar materials.

Techniques of microcapsule manufacture

Ionotropic gelation occurs when units of uric acid in the chains of the polymer alginate, crosslink with multivalent cations. These may include, calcium, zinc, iron and aluminium.

Coacervation-phase separation consists of three steps carried out under continuous agitation.

  1. Formation of three immiscible chemical phases: liquid manufacturing vehicle phase, core material phase and coating material phase.
  2. Deposition of coating: core material is dispersed in the coating polymer solution. Coating polymer material coated around core. Deposition of liquid polymer coating around core by polymer adsorbed at the interface formed between core material and vehicle phase.
  3. Rigidization of coating: coating material is immiscible in vehicle phase and is made rigid. This is done by thermal, cross-linking, or dissolution techniques.

Interfacial polycondensation

In interfacial polycondensation, the two reactants in a polycondensation meet at an interface and react rapidly. The basis of this method is the classical Schotten-Baumann reaction between an acid chloride and a compound containing an active hydrogen atom, such as an amine or alcohol, polyesters, polyurea, polyurethane. Under the right conditions, thin flexible walls form rapidly at the interface. A solution of the pesticide and a diacid chloride are emulsified in water and an aqueous solution containing an amine and a polyfunctional isocyanate is added. Base is present to neutralize the acid formed during the reaction. Condensed polymer walls form instantaneously at the interface of the emulsion droplets.

Interfacial cross-linking

Interfacial cross-linking is derived from interfacial polycondensation, and was developed to avoid the use of toxic diamines, for pharmaceutical or cosmetic applications. In this method, the small bifunctional monomer containing active hydrogen atoms is replaced by a biosourced polymer, like a protein. When the reaction is performed at the interface of an emulsion, the acid chloride reacts with the various functional groups of the protein, leading to the formation of a membrane. The method is very versatile, and the properties of the microcapsules (size, porosity, degradability, mechanical resistance) can be customized. Flow of artificial microcapsules in microfluidic channels:

In situ polymerization

In a few microencapsulation processes, the direct polymerization of a single monomer is carried out on the particle surface. In one process, e.g. cellulose fibers are encapsulated in polyethylene while immersed in dry toluene. Usual deposition rates are about 0.5μm/min. Coating thickness ranges 0.2–75 μm (0.0079–2.9528 mils). The coating is uniform, even over sharp projections. Protein microcapsules are biocompatible and biodegradable, and the presence of the protein backbone renders the membrane more resistant and elastic than those obtained by interfacial polycondensation.

Matrix polymerization

In a number of processes, a core material is imbedded in a polymeric matrix during formation of the particles. A simple method of this type is spray-drying, in which the particle is formed by evaporation of the solvent from the matrix material. However, the solidification of the matrix also can be caused by a chemical change.

Release methods and patterns

Even when the aim of a microencapsulation application is the isolation of the core from its surrounding, the wall must be ruptured at the time of use. Many walls are ruptured easily by pressure or shear stress, as in the case of breaking dye particles during writing to form a copy. Capsule contents may be released by melting the wall, or dissolving it under particular conditions, as in the case of an enteric drug coating. [7] In other systems, the wall is broken by solvent action, enzyme attack, chemical reaction, hydrolysis, or slow disintegration.

Microencapsulation can be used to slow the release of a drug into the body. This may permit one controlled release dose to substitute for several doses of non-encapsulated drug and also may decrease toxic side effects for some drugs by preventing high initial concentrations in the blood. There is usually a certain desired release pattern. In some cases, it is zero-order, i.e. the release rate is constant. In this case, the microcapsules deliver a fixed amount of drug per minute or hour during the period of their effectiveness. This can occur as long as a solid reservoir or dissolving drug is maintained in the microcapsule.

A more typical release pattern is first-order in which the rate decreases exponentially with time until the drug source is exhausted. In this situation, a fixed amount of drug is in solution inside the microcapsule. The concentration difference between the inside and the outside of the capsule decreases continually as the drug diffuses.

Nevertheless, there are some other mechanisms that may take place in the liberation of the encapsulated material. These include, biodegradation, osmotic pressure, diffusion, etc. Each one will depend on the composition of the capsule made and the environment it is in. Therefore, the liberation of the material may be affected by various mechanisms that act simultaneously. [8]

Applications

Applications of micro-encapsulation are numerous. It is mainly used to increase the stability and life of the product being encapsulated, facilitate the manipulation of the product and provide for the controlled release of the contents.

See also

Related Research Articles

An emulsion is a mixture of two or more liquids that are normally immiscible owing to liquid-liquid phase separation. Emulsions are part of a more general class of two-phase systems of matter called colloids. Although the terms colloid and emulsion are sometimes used interchangeably, emulsion should be used when both phases, dispersed and continuous, are liquids. In an emulsion, one liquid is dispersed in the other. Examples of emulsions include vinaigrettes, homogenized milk, liquid biomolecular condensates, and some cutting fluids for metal working.

<span class="mw-page-title-main">Dendrimer</span> Highly ordered, branched polymeric molecule

Dendrimers are highly ordered, branched polymeric molecules. Synonymous terms for dendrimer include arborols and cascade molecules. Typically, dendrimers are symmetric about the core, and often adopt a spherical three-dimensional morphology. The word dendron is also encountered frequently. A dendron usually contains a single chemically addressable group called the focal point or core. The difference between dendrons and dendrimers is illustrated in the top figure, but the terms are typically encountered interchangeably.

In materials science, the sol–gel process is a method for producing solid materials from small molecules. The method is used for the fabrication of metal oxides, especially the oxides of silicon (Si) and titanium (Ti). The process involves conversion of monomers in solution into a colloidal solution (sol) that acts as the precursor for an integrated network of either discrete particles or network polymers. Typical precursors are metal alkoxides. Sol–gel process is used to produce ceramic nanoparticles.

<span class="mw-page-title-main">Alginic acid</span> Polysaccharide found in brown algae

Alginic acid, also called algin, is a naturally occurring, edible polysaccharide found in brown algae. It is hydrophilic and forms a viscous gum when hydrated. With metals such as sodium and calcium, its salts are known as alginates. Its colour ranges from white to yellowish-brown. It is sold in filamentous, granular, or powdered forms.

<span class="mw-page-title-main">Sodium polyacrylate</span> Anionic polyelectrolyte polymer

Sodium polyacrylate (ACR, ASAP, or PAAS), also known as waterlock, is a sodium salt of polyacrylic acid with the chemical formula [−CH2−CH(CO2Na)−]n and has broad applications in consumer products. This super-absorbent polymer (SAP) has the ability to absorb 100 to 1000 times its mass in water. Sodium polyacrylate is an anionic polyelectrolyte with negatively charged carboxylic groups in the main chain. It is a polymer made up of chains of acrylate compounds. It contains sodium, which gives it the ability to absorb large amounts of water. When dissolved in water, it forms a thick and transparent solution due to the ionic interactions of the molecules. Sodium polyacrylate has many favorable mechanical properties. Some of these advantages include good mechanical stability, high heat resistance, and strong hydration. It has been used as an additive for food products including bread, juice, and ice cream.

An artificial cell, synthetic cell or minimal cell is an engineered particle that mimics one or many functions of a biological cell. Often, artificial cells are biological or polymeric membranes which enclose biologically active materials. As such, liposomes, polymersomes, nanoparticles, microcapsules and a number of other particles can qualify as artificial cells.

<span class="mw-page-title-main">Self-healing material</span> Substances that can repair themselves

Self-healing materials are artificial or synthetically created substances that have the built-in ability to automatically repair damages to themselves without any external diagnosis of the problem or human intervention. Generally, materials will degrade over time due to fatigue, environmental conditions, or damage incurred during operation. Cracks and other types of damage on a microscopic level have been shown to change thermal, electrical, and acoustical properties of materials, and the propagation of cracks can lead to eventual failure of the material. In general, cracks are hard to detect at an early stage, and manual intervention is required for periodic inspections and repairs. In contrast, self-healing materials counter degradation through the initiation of a repair mechanism that responds to the micro-damage. Some self-healing materials are classed as smart structures, and can adapt to various environmental conditions according to their sensing and actuation properties.

<span class="mw-page-title-main">Miniemulsion</span> Particular type of emulsion

A miniemulsion is a particular type of emulsion. A miniemulsion is obtained by ultrasonicating a mixture comprising two immiscible liquid phases, one or more surfactants and, possibly, one or more co-surfactants. They usually have nanodroplets with uniform size distribution (20–500 nm) and are also known as sub-micron, mini-, and ultra-fine grain emulsions.

A Ramsden emulsion, sometimes named Pickering emulsion, is an emulsion that is stabilized by solid particles which adsorb onto the interface between the water and oil phases. Typically, the emulsions are either water-in-oil or oil-in-water emulsions, but other more complex systems such as water-in-water, oil-in-oil, water-in-oil-in-water, and oil-in-water-in-oil also do exist. Pickering emulsions were named after S.U. Pickering, who described the phenomenon in 1907, although the effect was first recognized by Walter Ramsden in 1903.

<span class="mw-page-title-main">Janus particles</span> Type of nanoparticle or microparticle

Janus particles are special types of nanoparticles or microparticles whose surfaces have two or more distinct physical properties. This unique surface of Janus particles allows two different types of chemistry to occur on the same particle. The simplest case of a Janus particle is achieved by dividing the particle into two distinct parts, each of them either made of a different material, or bearing different functional groups. For example, a Janus particle may have one half of its surface composed of hydrophilic groups and the other half hydrophobic groups, the particles might have two surfaces of different color, fluorescence, or magnetic properties. This gives these particles unique properties related to their asymmetric structure and/or functionalization.

<span class="mw-page-title-main">Cardanol</span> Phenolic lipid

Cardanol is a phenolic lipid obtained from anacardic acid, the main component of cashew nutshell liquid (CNSL), a byproduct of cashew nut processing. Cardanol finds use in the chemical industry in resins, coatings, frictional materials, and surfactants used as pigment dispersants for water-based inks. It is used to make phenalkamines, which are used as curing agents for the durable epoxy coatings used on concrete floors. The name of the substance is derived by contraction from the genus Anacardium, which includes the cashew tree, Anacardium occidentale. The name of the genus itself is based on the Greek word for heart.

<span class="mw-page-title-main">Nano spray dryer</span>

Nano spray dryers refer to using spray drying to create particles in the nanometer range. Spray drying is a gentle method for producing powders with a defined particle size out of solutions, dispersions, and emulsions which is widely used for pharmaceuticals, food, biotechnology, and other industrial materials synthesis.

<span class="mw-page-title-main">Cell encapsulation</span>

Cell encapsulation is a possible solution to graft rejection in tissue engineering applications. Cell microencapsulation technology involves immobilization of cells within a polymeric semi-permeable membrane. It permits the bidirectional diffusion of molecules such as the influx of oxygen, nutrients, growth factors etc. essential for cell metabolism and the outward diffusion of waste products and therapeutic proteins. At the same time, the semi-permeable nature of the membrane prevents immune cells and antibodies from destroying the encapsulated cells, regarding them as foreign invaders.

Polyelectrolytes are charged polymers capable of stabilizing colloidal emulsions through electrostatic interactions. Their effectiveness can be dependent on molecular weight, pH, solvent polarity, ionic strength, and the hydrophilic-lipophilic balance (HLB). Stabilized emulsions are useful in many industrial processes, including deflocculation, drug delivery, petroleum waste treatment, and food technology.

A nanocapsule is a nanoscale shell made from a nontoxic polymer. They are vesicular systems made of a polymeric membrane which encapsulates an inner liquid core at the nanoscale. Nanocapsules have many uses, including promising medical applications for drug delivery, food enhancement, nutraceuticals, and for self-healing materials. The benefits of encapsulation methods are for protection of these substances to protect in the adverse environment, for controlled release, and for precision targeting. Nanocapsules can potentially be used as MRI-guided nanorobots or nanobots, although challenges remain.

<span class="mw-page-title-main">Polybutylene succinate</span> Biodegradable polymer

Polybutylene succinate (PBS) is a thermoplastic polymer resin of the polyester family. PBS is a biodegradable aliphatic polyester with properties that are comparable to polypropylene.

<span class="mw-page-title-main">Interfacial polymerization</span>

Interfacial polymerization is a type of step-growth polymerization in which polymerization occurs at the interface between two immiscible phases, resulting in a polymer that is constrained to the interface. There are several variations of interfacial polymerization, which result in several types of polymer topologies, such as ultra-thin films, nanocapsules, and nanofibers, to name just a few.

Nanoparticle drug delivery systems are engineered technologies that use nanoparticles for the targeted delivery and controlled release of therapeutic agents. The modern form of a drug delivery system should minimize side-effects and reduce both dosage and dosage frequency. Recently, nanoparticles have aroused attention due to their potential application for effective drug delivery.

<span class="mw-page-title-main">Dextran drug delivery systems</span> Polymeric drug carrier

Dextran drug delivery systems involve the use of the natural glucose polymer dextran in applications as a prodrug, nanoparticle, microsphere, micelle, and hydrogel drug carrier in the field of targeted and controlled drug delivery. According to several in vitro and animal research studies, dextran carriers reduce off-site toxicity and improve local drug concentration at the target tissue site. This technology has significant implications as a potential strategy for delivering therapeutics to treat cancer, cardiovascular diseases, pulmonary diseases, bone diseases, liver diseases, colonic diseases, infections, and HIV.

A clusteroid is a method of producing 3D cell cultures that was first developed in 2019. Clusteroids are grown as not true spheroids but as dense clusters of cells in an aqueous two-phase system of water-in-water Pickering emulsion. The cells are incapsulated by mixing two aqueous solutions containing the incompatible polymers: Polyethylene oxide (PEO) solution as a continuous phase and dextran solution (DEX) as a dispersed phase, using whey protein as a stabiliser. Clusteoids as an in vitro model are more accurate to the complexities of in vivo, and aren't as susceptible to some of the problems 2D cultures present, for example; A large problem in culturing cells as a 2D monolayer is confluence as most cell lines used in research tend to decline in growth and health above 80% due to competition between cells for nutrients and oxygen in their growth media. A unique problem in non-vascularised clusteroids is necrotic core formation; as nutrients and oxygen cannot diffuse into the centre of the clusteroid without other cells taking it up, the cells within become starved and subsequently die. This necrotic core formation is similar to that of poorly-vascularised solid tumours.

References

  1. ↑ Amaral, Pedro Henrique Rodrigues do; Andrade, Patrícia Lopes; Conto, Leilane Costa de (2019-09-27). Microencapsulation and Its Uses in Food Science and Technology: A Review. IntechOpen. ISBN   978-1-83881-870-8.
  2. 1 2 Lamprecht, Alf; Bodmeier, Roland (2010). "Microencapsulation". Ullmann's Encyclopedia of Industrial Chemistry. doi:10.1002/14356007.a16_575.pub2. ISBN   978-3-527-30385-4.
  3. ↑ Silva, Pablo Teixeira da; Fries, Leadir Lucy Martins; Menezes, Cristiano Ragagnin de; Holkem, Augusto Tasch; Schwan, Carla Luisa; Wigmann, Évelin Francine; Bastos, Juliana de Oliveira; Silva, Cristiane de Bona da (2014). "Microencapsulation: concepts, mechanisms, methods and some applications in food technology". Ciência Rural. 44 (7): 1304–1311. doi: 10.1590/0103-8478cr20130971 . ISSN   0103-8478. S2CID   42045080.
  4. ↑ Singh, M. N.; Hemant, K. S.; Ram, M; Shivakumar, H. G. (2010). "Microencapsulation: A promising technique for controlled drug delivery". Research in Pharmaceutical Sciences. 5 (2): 65–77. PMC   3093624 . PMID   21589795.
  5. ↑ Choudhury, Nitamani; Meghwal, Murlidhar; Das, Kalyan (2021-06-18). "Microencapsulation: An overview on concepts, methods, properties and applications in foods". Food Frontiers. 2 (4): 426–442. doi: 10.1002/fft2.94 . ISSN   2643-8429. S2CID   237925118.
  6. ↑ Fanger, Gene O. (1974), Vandegaer, Jan E. (ed.), "Microencapsulation: A Brief History and Introduction", Microencapsulation: Processes and Applications, Boston, MA: Springer US, pp. 1–20, doi:10.1007/978-1-4684-0739-6_1, ISBN   978-1-4684-0739-6 , retrieved 2022-02-28
  7. ↑ "Medical Dictionary: Enteric coating". Freedictionary.com. Retrieved 9 February 2009.
  8. ↑ Barba, A.A.; d'Amore, M.; Chirico, S.; Lamberti, G.; Titomalino, G. (2009). "A general code to predict the drug release kinetics from different shaped matrices". European Journal of Pharmaceutical Sciences. 36 (2–3): 359–368. doi:10.1016/j.ejps.2008.10.006. PMID   19022380.
  9. ↑ Singh, M.N.; Hemant, K.S.Y.; Ram, M.; Shivakumar, H.G. (2010). "Microencapsulation: A promising technique for controlled drug delivery". Research in Pharmaceutical Sciences. 5 (2): 65–77. ISSN   1735-5362. PMC   3093624 . PMID   21589795.
  10. ↑ Ciriminna, Rosaria; Sciortino, Marzia; Alonzo, Giuseppe; Schrijver, Aster de; Pagliaro, Mario (2011). "From Molecules to Systems: Sol−Gel Microencapsulation in Silica-Based Materials". Chemical Reviews. 111 (2): 765–789. doi:10.1021/cr100161x. PMID   20726523.
  11. ↑ Hedaoo, Rahul K.; et al. (2014). "Fabrication of Core–Shell Novel Polyurea Microcapsules Using Isophorone Diisocyanate (IPDI) Trimer for Release System". International Journal of Polymeric Materials and Polymeric Biomaterials. 63 (7): 352–360. doi:10.1080/00914037.2013.845191. S2CID   94019457.
  12. ↑ Mervosh, T.L.; EW Stoller; FW Simmons; TR Ellsworth; GK Sims (1995). "Effects of starch encapsulation on clomazone and atrazine movement in soil and clomazone volatilization". Weed Science. 43 (3): 445–453. doi:10.1017/S0043174500081455. S2CID   138347374.
  13. ↑ Puddu, M.; Paunescu, D.; Stark, W. J.; Grass, R. N. (2014). "Magnetically Recoverable, Thermostable, Hydrophobic DNA/Silica Encapsulates and Their Application as Invisible Oil Tags". ACS Nano. 8 (3): 2677–2685. doi:10.1021/nn4063853. PMID   24568212.
  14. ↑ Grass, R. N.; Heckel, R.; Puddu, M.; Paunescu, D.; Stark, W. J. (2015). "Robust Chemical Preservation of Digital Information on DNA in Silica with Error-Correcting Codes". Angewandte Chemie International Edition. 54 (8): 2552–2555. doi:10.1002/anie.201411378. PMID   25650567.
  15. ↑ Aizpurua-Olaizola, Oier; Navarro, Patricia; Vallejo, Asier; Olivares, Maitane; Etxebarria, Nestor; Usobiaga, Aresatz (2016-01-01). "Microencapsulation and storage stability of polyphenols from Vitis vinifera grape wastes". Food Chemistry. 190: 614–621. doi:10.1016/j.foodchem.2015.05.117. PMID   26213018.

Bibliography

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.