A waterfall display depicting several PSK31 transmissions at around 14,070 kHz. The green lines indicate a station that is transmitting.
PSK31 or "Phase Shift Keying, 31 Baud", also BPSK31 and QPSK31, is a popular computer-sound card-generated radioteletype mode, used primarily by amateur radio operators to conduct real-time keyboard-to-keyboard chat, most often using frequencies in the high frequencyamateur radio bands (near-shortwave). PSK31 is distinguished from other digital modes in that it is specifically tuned to have a data rate close to typing speed, and has an extremely narrow bandwidth, allowing many conversations in the same bandwidth as a single voice channel. This narrow bandwidth makes better use of the RF energy in a very narrow space thus allowing relatively low-power equipment (5 watts) to communicate globally using the same skywavepropagation used by shortwave radio stations.
PSK31 was developed and named by English amateur radio operator Peter Martinez (call sign G3PLX) and introduced to the wider amateur radio community in December 1998.[1][2]
The 31 baud BPSK modulation system used in PSK31 was introduced by Pawel Jalocha (SP9VRC) in his SLOWBPSK program written for Motorola's EVM radio. Instead of the traditional frequency-shift keying, the information is transmitted by patterns of polarity-reversals (sometimes called 180-degree phase shifts). PSK31 was enthusiastically received, and its usage spread rapidly worldwide, lending a new popularity and tone to the on-air conduct of digital communications.[citation needed] Due to the efficiency of the mode, it became, and still remains, especially popular with operators whose circumstances do not permit the installation of large antenna systems, the use of high power, or both.
A PSK31 operator typically uses a single-sideband (SSB) transceiver connected to the sound card of a computer running PSK31 software. When the operator enters a message for transmission, the software produces an audio tone that sounds, to the human ear, like a continuous whistle with a slight warble. This sound is then fed through either a microphone jack (using an intermediate resistive attenuator to reduce the sound card's output power to microphone levels) or an auxiliary connection into the transceiver, from which it is transmitted. [3]
From the perspective of the transmitter, the sound amounts to little more than somebody whistling into the microphone. However, the software rapidly shifts the phase of the audio signal between two states (hence the name "phase-shift keying"), forming the character codes. These phase shifts serve the same function as the two tones used in traditional RTTY and similar systems.
To decode PSK31, the audio whistle received from the transceiver's headphone output is fed into a computer sound card's audio input, and software decodes it. The software displays the decoded text.[3]
Because PSK31 was developed for use through a computer's sound card, many programs have since been created to use the same technology for other modes, such as RTTY, Hellschreiber, and Olivia MFSK. So, once it has been set up to run PSK31, a computer can be used for a variety of digital message transmission modes.
Aside from a standard radio transceiver and a computer with a sound card, very little equipment is required to use PSK31. Normally, an older computer and a few cables will suffice, and many PSK31 software applications are free and open source. Many operators now use a commercially available interface/modem device (or "nomic" [citation needed]) between their computers and radios. These devices incorporate the necessary impedance matching and sound level adjustment to permit the sound card output to be injected into the microphone input, send the radio's audio output to the sound card input, and handle the radio's transmit-receive switching. Sound card to radio interfaces typically use isolation transformers on both the send and receive audio paths to eliminate hum caused by ground-loops. Many interfaces also incorporate their own sound card and can be powered and run from the computer via a single USB connection. Some modern transceivers have these interfaces built in, requiring only a USB connection from the computer to the radio.
Resistance to interference
Like other narrow band digital modes, PSK31 can often overcome interference and poor propagation conditions in situations where voice or other methods of communication fail. However, PSK31 was designed only for leisure use by amateurs, and due to its relatively slow speed and limited error control, is not suitable for transmitting large blocks of data or text, or critical data requiring high immunity from errors.
PSK31 works well over propagation paths that preserve phase, and resists fading (QSB) well. However, it can be adversely affected by propagation modes—such as transpolar paths—where auroral "flutter" or multipathing can disrupt the signal phase continuity. In such cases the use of QPSK (see below) is often beneficial.
Some software supports PSK10 and PSK05 variants, running at 10 baud and 5 baud, respectively. These slower speeds sacrifice throughput to provide greater resistance to noise and other interference. Conversely, PSK63 is increasingly used for faster exchanges, especially during amateur radio contest operating.
Technical information
Example of PSK31 modulation
PSK31 is typically created by software that generates an amplitude- and phase-modulated waveform that is converted to an audio frequency analog signal by a sound card. In the most-commonly-used variant, BPSK31, binary information is transmitted by either imparting a 180-degree phase shift (a binary "zero") or no phase shift (a binary "one") in each 32ms symbol interval. The 180-degree phase shift for a "zero" bit code occurs at a null amplitude.[4]
As shown in the figure, a cosine filter is used to smooth the rise and fall times of the audio waveform and eliminate key clicks. All subsequent amplification of the signal must be linear to preserve the modulation waveform and ensure minimum occupied bandwidth. In practice, this means limiting the transmit audio volume to below the level where the transmitter generates Automatic Level Control (ALC) feedback and disabling any audio compression or speech processing.
The Varicode is a kind of Fibonacci code where the boundaries between character codes are marked by two or more consecutive zeros. Like all Fibonacci codes, since no character code contains more than one consecutive zero, the software can easily identify the spaces between characters, regardless of the length of the character. The idle sequence, sent when an operator is not typing, is a continuous sequence of phase-shifts, which do not print on the screen.[2] Martinez arranged the character alphabet so that, as in Morse code, the more frequently occurring characters have the shortest encodings, while rarer characters use longer encodings. He named this encoding scheme "varicode".
PSK31's symbol rate of 31.25Hz was chosen because a normal typing speed of about 50 words per minute requires a bit rate of about 32 bits per second, and specifically because 31.25Hz could easily be derived from the 8kHz sample rate used in many DSP systems, including those used in the computer sound cards commonly used for PSK31 operation (31.25Hz is 8kHz divided by 256, and so can be derived from 8kHz by halving the frequency eight times in succession).
BPSK31 and QPSK31 variants
Colloquial usage of the term 'PSK31' in amateur radio usually implies the use of the most commonly used variant of PSK31: binary phase shift keying (BPSK). The BPSK variant of PSK31 uses no error control. QPSK31, the variant based on quadrature phase shift keying (QPSK), uses four phases instead of two. It is simple to switch from BPSK to QPSK if difficulties arise during a contact; QPSK31 has the same number of symbols per second, and hence the same bandwidth as the BPSK variant. In a coherent receiver, the bit error probability of QPSK is the same as for BPSK operating at the same power, making QPSK31 the generally preferable mode from a robustness, and thus reach, point of view.
Using four instead of two constellation points provides twice the physical layer bit rate, which allows addition of redundant information to provide a degree of forward error correction. When QPSK is used, after encoding into varicode, the bits of the binary data signal is subject to a rate-1/2 channel code, which means that for every information bit, two code bits are calculated and transmitted. For that, a convolutional code with constraint length 5 (i.e. the last five bits from the input are incorporated to select two output bits per input bit) is used.
The resulting bits are mapped to a quaternary set of phases. At the receiver, a decoder for the convolutional code needs to be used, typically the Viterbi Algorithm, which is able to reconstruct the most likely sent sequence, even if multiple symbols were received incorrectly. Optimal decoding must take into account the same constraint length of information bits as encoding, yielding a 5-symbol decoding delay, which corresponds to 160 ms of delay.
Spectrum efficiency compared to other modes
Frequency spectrum of an ideal non-splattering PSK31 signalFrequency spectrum of a splattering PSK31 signal
PSK31's efficiency and narrow bandwidth make it highly suitable for low-power and crowded-band operation. PSK31 contacts can be conducted at less than 100Hz separation, so with disciplined operation at least twenty simultaneous PSK31 contacts can be carried out side-by-side in the 2.5kHz bandwidth required for just one SSB voice contact.
Common frequencies
The following amateur radio frequencies are commonly used for transmitting and receiving PSK31 signals. They normally occupy the lower edge of each band's digital modes section. PSK31 operators generally use upper sideband (USB), even on frequencies below 10MHz where the convention normally calls for lower sideband. This is because (a) signals then spread upwards into the digimode section from the "base" frequency, and (b) using QPSK requires both stations to use the same sideband.
* Current usage as of 2010, based on observation, is centered on 7,070.15 and 21,070.15. 7,035.15 is commonly used in Region 2 as of 2012. There is no authoritative list, as the frequencies are determined by common convention.
** PSK has moved from 18.100 to 18.097 due to FT8 use of the 18.100 frequency as of November, 2019.
The IARU Region 1 Bandplan was revised in March 2009 to reflect the expanded 40 meter band. The CW-only section within Europe, Africa, the Middle East and the former USSR is now 7.000 to 7.040. Region 2 - The Americas - followed in September 2013. Region 3 - South Asia and Australasia - has not yet synchronised its bandplan with Regions 1 and 2.
Related Research Articles
Frequency modulation (FM) is the encoding of information in a carrier wave by varying the instantaneous frequency of the wave. The technology is used in telecommunications, radio broadcasting, signal processing, and computing.
In electronics and telecommunications, modulation is the process of varying one or more properties of a periodic waveform, called the carrier signal, with a separate signal called the modulation signal that typically contains information to be transmitted. For example, the modulation signal might be an audio signal representing sound from a microphone, a video signal representing moving images from a video camera, or a digital signal representing a sequence of binary digits, a bitstream from a computer.
In digital radio, packet radio is the application of packet switching techniques to digital radio communications. Packet radio uses a packet switching protocol as opposed to circuit switching or message switching protocols to transmit digital data via a radio communication link.
Radioteletype (RTTY) is a telecommunications system consisting originally of two or more electromechanical teleprinters in different locations connected by radio rather than a wired link. Radioteletype evolved from earlier landline teleprinter operations that began in the mid-1800s. The US Navy Department successfully tested printing telegraphy between an airplane and ground radio station in 1922. Later that year, the Radio Corporation of America successfully tested printing telegraphy via their Chatham, Massachusetts, radio station to the R.M.S. Majestic. Commercial RTTY systems were in active service between San Francisco and Honolulu as early as April 1932 and between San Francisco and New York City by 1934. The US military used radioteletype in the 1930s and expanded this usage during World War II. From the 1980s, teleprinters were replaced by personal computers (PCs) running software to emulate teleprinters.
In radio communications, single-sideband modulation (SSB) or single-sideband suppressed-carrier modulation (SSB-SC) is a type of modulation used to transmit information, such as an audio signal, by radio waves. A refinement of amplitude modulation, it uses transmitter power and bandwidth more efficiently. Amplitude modulation produces an output signal the bandwidth of which is twice the maximum frequency of the original baseband signal. Single-sideband modulation avoids this bandwidth increase, and the power wasted on a carrier, at the cost of increased device complexity and more difficult tuning at the receiver.
Phase-shift keying (PSK) is a digital modulation process which conveys data by changing (modulating) the phase of a constant frequency carrier wave. The modulation is accomplished by varying the sine and cosine inputs at a precise time. It is widely used for wireless LANs, RFID and Bluetooth communication.
In radio communications, a sideband is a band of frequencies higher than or lower than the carrier frequency, that are the result of the modulation process. The sidebands carry the information transmitted by the radio signal. The sidebands comprise all the spectral components of the modulated signal except the carrier. The signal components above the carrier frequency constitute the upper sideband (USB), and those below the carrier frequency constitute the lower sideband (LSB). All forms of modulation produce sidebands.
Slow-scan television (SSTV) is a picture transmission method, used mainly by amateur radio operators, to transmit and receive static pictures via radio in monochrome or color.
Very low frequency or VLF is the ITU designation for radio frequencies (RF) in the range of 3–30 kHz, corresponding to wavelengths from 100 to 10 km, respectively. The band is also known as the myriameter band or myriameter wave as the wavelengths range from one to ten myriameters. Due to its limited bandwidth, audio (voice) transmission is highly impractical in this band, and therefore only low data rate coded signals are used. The VLF band is used for a few radio navigation services, government time radio stations and for secure military communication. Since VLF waves can penetrate at least 40 meters (131 ft) into saltwater, they are used for military communication with submarines.
Digital Radio Mondiale is a set of digital audio broadcasting technologies designed to work over the bands currently used for analogue radio broadcasting including AM broadcasting—particularly shortwave—and FM broadcasting. DRM is more spectrally efficient than AM and FM, allowing more stations, at higher quality, into a given amount of bandwidth, using xHE-AAC audio coding format. Various other MPEG-4 codecs and Opus are also compatible, but the standard now specifies xHE-AAC.
The Hellschreiber, Feldhellschreiber or Typenbildfeldfernschreiber is a facsimile-based teleprinter invented by Rudolf Hell. Compared to contemporary teleprinters that were based on typewriter systems and were mechanically complex and expensive, the Hellschreiber was much simpler and more robust, with far fewer moving parts. It has the added advantage of being capable of providing intelligible communication even over very poor quality radio or cable links, where voice or other teledata would be unintelligible.
In a radio receiver, a beat frequency oscillator or BFO is a dedicated oscillator used to create an audio frequency signal from Morse code radiotelegraphy (CW) transmissions to make them audible. The signal from the BFO is mixed with the received signal to create a heterodyne or beat frequency which is heard as a tone in the speaker. BFOs are also used to demodulate single-sideband (SSB) signals, making them intelligible, by essentially restoring the carrier that was suppressed at the transmitter. BFOs are sometimes included in communications receivers designed for short wave listeners; they are almost always found in communication receivers for amateur radio, which often receive CW and SSB signals.
The Bell 103 modem or Bell 103 dataset was the second commercial modem for computers, released by AT&T Corporation in 1963. It allowed digital data to be transmitted over regular unconditioned telephone lines at a speed of 300 bits per second. It followed the introduction of the 110 baud Bell 101 dataset in 1958.
Olivia MFSK is an amateur radioteletype protocol, using multiple frequency-shift keying (MFSK) and designed to work in difficult conditions on shortwave bands. The signal can be accurately received even if the surrounding noise is 10 dB stronger. It is commonly used by amateur radio operators to reliably transmit ASCII characters over noisy channels using the high frequency (3–30 MHz) spectrum. The effective data rate of the Olivia MFSK protocol is 150 characters/minute.
CLOVER is the name of a series or class of modem modulation techniques (“waveforms”) specifically designed for use over high frequency (HF) radio systems.
Q15X25 is a communications protocol for sending data over a radio link. It was designed by amateur radio operator Pawel Jalocha, SP9VRC, to be an open communications standard. Like all amateur radio communications modes, this protocol uses open transmissions which can be received and decoded by anyone with similar equipment. Q15X25 is a form of packet radio. It can be used to interconnect local VHF AX.25 packet networks over transcontinental distances. Anyone can design or adapt the open-source software to develop their own Q15X25 system.
An amateur radio repeater is an electronic device that receives a weak or low-level amateur radio signal and retransmits it at a higher level or higher power, so that the signal can cover longer distances without degradation. Many repeaters are located on hilltops or on tall buildings as the higher location increases their coverage area, sometimes referred to as the radio horizon, or "footprint". Amateur radio repeaters are similar in concept to those used by public safety entities, businesses, government, military, and more. Amateur radio repeaters may even use commercially packaged repeater systems that have been adjusted to operate within amateur radio frequency bands, but more often amateur repeaters are assembled from receivers, transmitters, controllers, power supplies, antennas, and other components, from various sources.
WSJT-X is a computer program used for weak-signal radio communication between amateur radio operators. The program was initially written by Joe Taylor, K1JT, but is now open source and is developed by a small team. The digital signal processing techniques in WSJT-X make it substantially easier for amateur radio operators to employ esoteric propagation modes, such as high-speed meteor scatter and moonbounce. Additionally WSJT is able to send signal reports to spotting networks such as PSK Reporter.
Fldigi is a free and open-source program which allows an ordinary computer's sound card to be used as a simple two-way data modem. The software is mostly used by amateur radio operators who connect the microphone and headphone connections of an amateur radio SSB or FM transceiver to the computer's headphone and microphone connections, respectively.
References
↑ The ARRL Handbook for Radio Communications. 84th Ed. (2007):9-13.
1 2 Steven L Karty, N5SK. "PSK31 Spec". ARRL Website. Retrieved 18 Dec 2010.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
