| SER R class | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 | |||||||||||||
| |||||||||||||
| |||||||||||||
| |||||||||||||
The SER R class was a class of 0-6-0T locomotives on the South Eastern Railway.
| SER R class | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| | |||||||||||||
| |||||||||||||
| |||||||||||||
| |||||||||||||
The SER R class was a class of 0-6-0T locomotives on the South Eastern Railway.
For many years the South Eastern Railway (SER) had possessed very few locomotives designed for shunting. When trains were to be shunted, this was usually carried out any locomotive which happened to be idle at the time, which was often unsuitable; and sometimes this caused delays to other trains which should have been run using the commandeered locomotive. [1]
Several other railways favoured the 0-6-0T wheel arrangement for shunting, and so in 1887 it was decided to introduce a class of 0-6-0T locomotives specifically for shunting and for hauling local goods trains. [1] The R class locomotives were designed by James Stirling as a new class, and 25 were built at Ashford Works between 1888 and 1898. [2] [3] As was typical of Stirling's designs, several components were shared with existing designs; the domeless boilers were of the same type as was fitted to his O class 0-6-0 and Q class 0-4-4T. [4]
Their SER numbers were scattered between 10 and 174, and in a continuous block from 335 to 342. [3] These numbers were retained under the South Eastern and Chatham Railway, although from 1900 the livery changed from black to green. [5]
| Year | Quantity | SER Nos. |
|---|---|---|
| 1888 | 4 | 335–338 |
| 1889 | 4 | 339–342 |
| 1890 | 3 | 10, 77, 147 |
| 1892 | 6 | 124, 128, 152–154, 174 |
| 1895 | 4 | 47, 125–127 |
| 1898 | 4 | 69, 70, 107, 155 |
The three 1890 locomotives (nos. 10, 77, 147) were built with short chimneys giving an overall height of 11 ft 6 in (3.51 m) to give sufficient clearance for working the Whitstable branch, which had a low tunnel. Normally, two would work the branch from Canterbury West shed whilst the third was spare at Ashford, but to provide relief for the 1890 locomotives when one was undergoing overhaul, no. 124 was also given a short chimney in March 1893. [6]
Three of the 1892 locomotives were built for the Folkestone Harbour Branch, where the existing locomotives, Mansell 0-6-0T nos. 152–154, were only fourteen years old, but required several modifications in order to comply with Board of Trade regulations regarding passenger trains. In particular they needed to be equipped with the automatic vacuum brake which would itself require the locomotives to have stronger frames. Their boilers would also become due for replacement soon, and it was decided that the provision of three new R class locomotives would be more economic, and these took the same numbers as the locomotives that they replaced, which were scrapped. R class nos. 152–154 were transferred to other parts of the SER system in 1898, and were replaced on the Folkestone Harbour Branch by newly-built nos. 69, 70 and 107. [7]
| SECR R1 class | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
 Two R1 locomotives 1069 and 1147 at Ashford 1946. These have been cut down to operate on the restrictive Canterbury & Whitstable line | |||||||||||
| |||||||||||
| |||||||||||
| |||||||||||
Between 1910 and 1922, [3] 13 of the SER R class 0-6-0T were rebuilt by the SECR with Wainwright-design domed boilers of the same type as were used on the SECR H class 0-4-4T. [8] These rebuilds were classified R1, but their capabilities and duties did not change substantially.
| Year | Quantity | SECR Nos. |
|---|---|---|
| 1910 | 1 | 69 |
| 1911 | 1 | 339 |
| 1912 | 2 | 147, 154 |
| 1913 | 4 | 10, 47, 128, 340 |
| 1914 | 3 | 107, 127, 174 |
| 1915 | 1 | 335 |
| 1922 | 1 | 337 |
Many of the locomotives were renumbered up to three times: from 1924 the Southern Railway (SR) applied the prefix "A", i.e. A10 etc., the work being completed in 1927; [9] from 1931 the SR dropped the "A" and increased the numbers by 1000 (i.e. 1010 etc.); and from 1948, under British Railways, the numbers were further increased by 30000, becoming 31010 etc.
One R class locomotive (no. 341) was withdrawn in 1914 due to accident damage. [10] The other 11 locomotives which had not been rebuilt to the R1 class were withdrawn between 1931 and 1943. [11] Of the 13 R1 class rebuilds, one was withdrawn in 1949, two in 1955, three in 1958 and five in 1959; after August 1959, only nos. 31047 and 31337 were left, and these were withdrawn in March and February 1960 respectively. [12]
| Year | R class in service at start of year | R1 class in service at start of year | Quantity withdrawn | Locomotive numbers | Notes |
|---|---|---|---|---|---|
| 1931 | 11 | 13 | 1 | 1342 | |
| 1932 | 10 | 13 | 1 | 1077 | |
| 1934 | 9 | 13 | 3 | 1126, 1152, 1338 | |
| 1935 | 6 | 13 | 1 | 1153 | |
| 1937 | 5 | 13 | 1 | 1125 | |
| 1939 | 4 | 13 | 1 | 1155 | |
| 1941 | 3 | 13 | 1 | 1336 | |
| 1942 | 2 | 13 | 1 | 1070 | |
| 1943 | 1 | 13 | 1 | 1124 | |
| 1949 | 0 | 13 | 1 | 1127 | |
| 1955 | — | 12 | 2 | 31154, 31335 | |
| 1958 | — | 10 | 2 | 31069, 31147 | |
| 1959 | — | 8 | 6 | 31010, 31107, 31128, 31174, 31339, 31340 | |
| 1960 | — | 2 | 2 | 31047, 31337 |
The Hornby Dublo range of 00 gauge model railways had been launched by Meccano Ltd in 1938 using a three-rail system to power the electric motors of the locomotives. [13] After World War II, several of their rivals chose a two-rail system and by 1957 Hornby Dublo began to lose sales. [14] Accordingly, they decided to develop a two-rail system, and this was launched in 1959. Among the new items designed especially for the two-rail launch was a model of the SECR R1 class 0-6-0T; [15] this was moulded in polystyrene, which was coloured either black (with running number 31337) or green (as number 31340), both carrying the contemporary BR emblem; [16] it has been stated that the two running numbers were carefully chosen to match the numbers of the last two in service, [17] but in fact at the time of the withdrawal of 31340, there were still six others in service. [3] They were announced in Meccano Magazine in September 1960, [18] and remained in production until the collapse of the Meccano group in 1964. [18] [19]
The Southern Railway took a key role in expanding the 660 V DC third rail electrified network begun by the London & South Western Railway. As a result of this, and its smaller operating area, its steam locomotive stock was the smallest of the 'Big Four' companies.
The SR Z class was an 0-8-0T 3-cylinder tank engine designed by Richard Maunsell and intended for heavy shunting on the Southern Railway, the first eight entering into service in 1929. It was a successful design and would have been built in greater numbers, but an order for a further ten was cancelled in 1930 due to the reduction in freight traffic as a result of the Great Depression.
The GWR 5700 Class is a class of 0-6-0 pannier tank steam locomotive built by the Great Western Railway (GWR) and British Railways (BR) between 1929 and 1950. With 863 built, they were the most prolific class of the GWR, and one of the most numerous classes of British steam locomotive.
The South Eastern and Chatham Railway (SECR) P class is a class of 0-6-0T steam locomotive designed by Harry Wainwright.
The South Eastern and Chatham Railway (SECR) H Class is a class of 0-4-4T steam locomotive originally designed for suburban passenger work, designed by Harry Wainwright in 1904. Most of the sixty-six members of the class were later equipped for push-pull working for use on rural branch lines.
The London, Brighton and South Coast Railway (LB&SCR) E2 class was a class of 0-6-0T steam locomotives designed by Lawson Billinton, intended for shunting and short distance freight trains. Ten examples were built between 1913 and 1916, and were withdrawn from service and scrapped between 1961 and 1963.
Harry Smith Wainwright was an English railway engineer, and was the Locomotive, Carriage and Wagon Superintendent of the South Eastern and Chatham Railway from 1899 to 1913. He is best known for a series of simple but competent locomotives produced under his direction at the company's Ashford railway works in the early years of the twentieth century. Many of these survived in service until the end of steam traction in Britain in 1968, and are regarded as some of the most elegant designs of the period.
The GS&WR Class 201 was a class of ten 0-6-0T locomotives designed by Locomotive Engineer, Henry Ivatt in 1887 for shunting heavy goods trains at Kingsbridge and Cork yards. Although the design is generally attributed to Ivatt they were actually created in the last year of Alexander McDonnell's tenure. The locomotives were built in three batch with variations between batches: Nos. 207—210 were introduced in 1887; 201 and 202 followed in 1895 taking numbers formerly held by Sambo and Negro; while the final batch 214—217 emerged in 1901.
The South Eastern Railway (SER) O Class was a class of 0-6-0 steam locomotive designed for freight work, and were the main freight engines of the SER, and later the South Eastern and Chatham Railway (SECR) for a number of years. However, they were displaced by the more powerful C class locomotives following the amalgamation of the South Eastern Railway and London, Chatham and Dover Railway (LCDR) in 1899. This relegated the class to working on the numerous branch lines in Kent, on both passenger and freight work. They worked most notably on the Kent & East Sussex Railway and East Kent Railway, operating coal trains from the Kent coal fields to London, as well as shunting work at such locations as Shepherds Well, Hoo Junction and Ashford. The majority were withdrawn before the outbreak of the Second World War in 1939, and those that remained were slowly withdrawn from nationalisation onwards.
The Great Northern Railway (GNR) Class N2 is an 0-6-2T side tank steam locomotive designed by Nigel Gresley and introduced in 1920. Further batches were built by the London and North Eastern Railway from 1925. They had superheaters and piston valves driven by Stephenson valve gear.
The London and North Eastern Railway (LNER) D40 class is a type of 4-4-0 steam locomotive inherited from the Great North of Scotland Railway (GNSR). It consisted of GNSR class V and GNSR class F. The two classes were similar but the class F was superheated.
The London, Brighton and South Coast Railway E3 class were 0-6-2T side tank steam locomotives. One prototype was designed by William Stroudley shortly before his death, but was completed by R. J. Billinton, who later built sixteen further locomotives.
The London, Brighton and South Coast Railway E1 Class were 0-6-0T steam locomotives designed by William Stroudley in 1874 for short-distance goods and piloting duties. They were originally classified E, and generally known as "E-tanks"; They were reclassified E1 in the time of D. E. Marsh.
The SECR B1 class was a class of 4-4-0 steam tender locomotive for express passenger service on the South Eastern and Chatham Railway. These engines were originally designed by James Stirling for the South Eastern Railway (SER) in 1898 and designated B class. The SER was merged into the SECR in 1899 and, between 1910 and 1927 the B class engines were rebuilt with new boilers by Harry Wainwright to become B1 class.
James Stirling (1835–1917) was a Scottish mechanical engineer. He was Locomotive Superintendent of the Glasgow and South Western Railway and later the South Eastern Railway. Stirling was born on 2 October 1835, a son of Robert Stirling, rector of Galston, East Ayrshire.
The LCDR R1 class was a class of 0-4-4T locomotives on the South Eastern and Chatham Railway (SECR), which were based on an existing London, Chatham and Dover Railway (LCDR) design.
The NER Class 290 was a class of 0-6-0T steam locomotives of the North Eastern Railway (NER), rebuilt from an earlier class of 0-4-4T, the NER Bogie Tank Passenger.
The LCDR Second Sondes class was a class of six 2-4-0T steam locomotives. They were designed by William Martley for the London, Chatham and Dover Railway (LCDR), and built at the LCDR's Longhedge works during 1865, using components from the Sondes class 4-4-0ST locomotives, including the boilers.
The LCDR Aeolus class was a class of four 4-4-0 steam locomotives. They were supplied to the London, Chatham and Dover Railway (LCDR) by R. & W. Hawthorn & Co. acting as agents for Robert Stephenson & Co. which built the locomotives, but had subcontracted some components to Hawthorn. They were delivered to the LCDR between September 1860 and April 1861. They were all renewed by William Martley as 2-4-0T at the LCDR's Longhedge works in 1872–73, using components from the original locomotives, including the boilers.
The SER A class was a class of 4-4-0 locomotives on the South Eastern Railway.