| SD-260 | |
|---|---|
 | |
| The SD-260 prototype under construction showing the structure | |
| Role | Homebuilt aircraft |
| National origin | United States |
| Manufacturer | SkyDancer Aviation |
| Status | Production completed |
| Number built | At least two |
The SkyDancer SD-260 was an American aerobatic homebuilt biplane that was designed and produced by SkyDancer Aviation of Louisville, Kentucky, introduced in the mid-1990s. When it was available the aircraft was supplied as a kit. [1]
The SD-260 featured a strut-braced biplane layout, a two-seats-in-tandem open cockpit, with an optional bubble canopy, fixed conventional landing gear with wheel pants and a single engine in tractor configuration. [1]
The aircraft fuselage was made from welded 4130 steel tubing. Its 22.00 ft (6.7 m) span had a wooden structure with four ailerons, a wing area of 135.0 sq ft (12.54 m2) and was covered in doped aircraft fabric. The wing was supported by interplane struts, cabane struts and flying wires. The acceptable power range was 200 to 400 hp (149 to 298 kW) and the standard engine used was the 260 hp (194 kW) Lycoming IO-540 powerplant. [1]
The SD-260 had a typical empty weight of 1,250 lb (570 kg) and a gross weight of 1,850 lb (840 kg), giving a useful load of 600 lb (270 kg). With full fuel of 29 U.S. gallons (110 L; 24 imp gal) the payload for the pilot, passenger and baggage was 426 lb (193 kg). [1]
The standard day, sea level, no wind, take off with a 260 hp (194 kW) engine was 600 ft (183 m) and the landing roll was 800 ft (244 m). [1]
The manufacturer estimated the construction time from the supplied kit as 1200 hours. [1]
In March 2014 no examples were registered in the United States with the Federal Aviation Administration, although a total of two had been registered at one time. It is unlikely any remain in existence. [2]
Data from AeroCrafter [1]
General characteristics
Performance
The Barrows Bearhawk, now also called the Barrows 4-Place Bearhawk, is an American amateur-built aircraft, designed by Bob Barrows and produced by R&B Aircraft of Fincastle, Virginia, AviPro Aircraft and now Bearhawk Aircraft of Austin, Texas. The aircraft is supplied as a kit or as plans for amateur construction.
The Pitts Special is a series of light aerobatic biplanes designed by Curtis Pitts. It has accumulated many competition wins since its first flight in 1944. The Pitts biplanes dominated world aerobatic competition in the 1960s and 1970s and, even today, remain potent competition aircraft in the lower categories.
The Aristocraft II was a six-place homebuilt aircraft designed by Terrence O'Neill.
The ULBI Wild Thing is a German ultralight aircraft, designed by R. Kurtz and produced by Ultraleicht Bau International (ULBI), of Hassfurt. The aircraft was supplied as a kit for amateur construction or as a complete ready-to-fly-aircraft.
The Peña Bilouis is a French aerobatic amateur-built aircraft that was designed by the competitive aerobatic pilot Louis Peña of Dax, Landes and made available in the form of plans for amateur construction.
The Raven 2XS is a Canadian aerobatic amateur-built biplane, designed and produced by Raven Aircraft of Surrey, British Columbia. The aircraft is supplied as a kit or as plans for amateur construction.
The Skipper Scrappy UAC-200 is an American homebuilt aerobatic biplane that was designed by WA Skipper of Greeley, Colorado, introduced in 1970. The aircraft was supplied in the form of plans for amateur construction, but plans seem to no longer be available.
The Adventure Air Adventurer is a family of American homebuilt amphibious flying boats that was designed and produced by Adventure Air of Berryville, Arkansas. When it was available the aircraft was supplied as a kit for amateur construction. The company appears to be out of business.
national
The Rihn DR-109 is an American aerobatic homebuilt aircraft that was designed by Dan Rihn. The aircraft was supplied by Jim Kimball Enterprises of Zellwood, Florida and more recently by Ashcraft Aero Works of Aurora, Illinois in the form of plans. It was designed for competition aerobatics as well as a trainer for the Rihn DR-107 One Design.
The Aircraft Technologies Acro 1 is an American aerobatic homebuilt aircraft that was designed by Fred Meyer and produced by Aircraft Technologies of Lilburn, Georgia. When it was available the aircraft was supplied as a kit or in the form of plans for amateur construction. Neither plans nor kits are available anymore and the aircraft is out of production.
The Giles G-200 is an American aerobatic homebuilt aircraft that was produced by AkroTech Aviation of Scappoose, Oregon. When it was available the aircraft was supplied as a complete ready-to-fly-aircraft or a kit for amateur construction. AkroTech Aviation went out of business and the design is no longer in production.
The Christavia Mk IV (Christ-in-Aviation) is a Canadian homebuilt aircraft that was designed by Ron Mason and produced by Elmwood Aviation of Frankford, Ontario. The aircraft is supplied in the form of plans for amateur construction.
The Culp Special is an American aerobatic homebuilt aircraft designed and produced by Culp's Specialties of Shreveport, Louisiana. The aircraft is supplied as a kit or in the form of plans for amateur construction.
The Explorer Ellipse is an American homebuilt aircraft that was designed by Dean Wilson and produced by Explorer Aviation of Grangeville, Idaho. When it was available the aircraft was supplied as a kit for amateur construction.
The Glassic SQ2000 is an American homebuilt aircraft, designed and produced by Glassic Composites LLC of Sale Creek, Tennessee. When it was available the aircraft was supplied as a kit for amateur construction.
The Starfire Firebolt, sometimes called the Starfire Firebolt Convertible, due to its removable canopy, is an American homebuilt aerobatic biplane that was designed by G. H. "Mac" McKenzie and produced by Starfire Aviation of Tempe, Arizona. When it was available the aircraft was supplied in the form of plans for amateur construction, with some pre-fabricated parts available.
The Ultimate 10-200 is a Canadian homebuilt aerobatic biplane that was designed produced by Streamline Welding of Hamilton, Ontario, introduced in the 1990s. When it was available the aircraft was supplied as a kit or in the form of plans for amateur construction.
The Tech Aero TR 200 is a French homebuilt aerobatic aircraft that was designed and produced by Tech Aero of Glisolles, first flown in August 1988. When it was available the aircraft was supplied as a kit for amateur construction.
The Warner Revolution II, also marketed as the Space Walker II, is an American homebuilt aircraft that was designed and produced by Warner Aerocraft of Seminole, Florida. When it was available the aircraft was supplied as a kit or in the form of plans for amateur construction.