Torsion (mechanics)

Last updated December 10, 2024

In the field of solid mechanics, torsion is the twisting of an object due to an applied torque ^[1]^[2]. Torsion could be defined as strain^[3]^[4] or angular deformation^[5], and is measured by the angle a chosen section is rotated from its equilibrium position^[6]. The resulting stress (torsional shear stress) is expressed in either the pascal (Pa), an SI unit for newtons per square metre, or in pounds per square inch (psi) while torque is expressed in newton metres (N·m) or foot-pound force (ft·lbf). In sections perpendicular to the torque axis, the resultant shear stress in this section is perpendicular to the radius.

T is the applied torque or moment of torsion in Nm.
$\tau$ (tau) is the maximum shear stress at the outer surface
J_T is the torsion constant for the section. For circular rods, and tubes with constant wall thickness, it is equal to the polar moment of inertia of the section, but for other shapes, or split sections, it can be much less. For more accuracy, finite element analysis (FEA) is the best method. Other calculation methods include membrane analogy and shear flow approximation.^[8]
r is the perpendicular distance between the rotational axis and the farthest point in the section (at the outer surface).
ℓ is the length of the object to or over which the torque is being applied.
φ (phi) is the angle of twist in radians.
G is the shear modulus, also called the modulus of rigidity, and is usually given in gigapascals (GPa), lbf/in² (psi), or lbf/ft² or in ISO units N/mm².
The product J_TG is called the torsional rigidity w_T.

Properties

The shear stress at a point within a shaft is:

\tau _{\varphi _{z}}(r)={Tr \over J_{\text{T}}}

Note that the highest shear stress occurs on the surface of the shaft, where the radius is maximum. High stresses at the surface may be compounded by stress concentrations such as rough spots. Thus, shafts for use in high torsion are polished to a fine surface finish to reduce the maximum stress in the shaft and increase their service life.

The angle of twist can be found by using:

\varphi _{}={\frac {T\ell }{GJ_{\text{T}}}}.

Sample calculation

Calculation of the steam turbine shaft radius for a turboset:

Assumptions:

Power carried by the shaft is 1000 MW; this is typical for a large nuclear power plant.
Yield stress of the steel used to make the shaft (τ_yield) is: 250 × 10⁶ N/m².
Electricity has a frequency of 50 Hz; this is the typical frequency in Europe. In North America, the frequency is 60 Hz.

The angular frequency can be calculated with the following formula:

\omega =2\pi f

The torque carried by the shaft is related to the power by the following equation:

P=T\omega

The angular frequency is therefore 314.16 rad/s and the torque 3.1831 × 10⁶ N·m.

The maximal torque is:

T_{\max }={\frac {{\tau }_{\max }J_{\text{zz}}}{r}}

After substitution of the torsion constant , the following expression is obtained:

D=\left({\frac {16T_{\max }}{\pi {\tau }_{\max }}}\right)^{1/3}

The diameter is 40 cm. If one adds a factor of safety of 5 and re-calculates the radius with the maximum stress equal to the yield stress/5, the result is a diameter of 69 cm, the approximate size of a turboset shaft in a nuclear power plant.

Failure mode

The shear stress in the shaft may be resolved into principal stresses via Mohr's circle. If the shaft is loaded only in torsion, then one of the principal stresses will be in tension and the other in compression. These stresses are oriented at a 45-degree helical angle around the shaft. If the shaft is made of brittle material, then the shaft will fail by a crack initiating at the surface and propagating through to the core of the shaft, fracturing in a 45-degree angle helical shape. This is often demonstrated by twisting a piece of blackboard chalk between one's fingers.^[9]

In the case of thin hollow shafts, a twisting buckling mode can result from excessive torsional load, with wrinkles forming at 45° to the shaft axis.

Related Research Articles

In classical mechanics, a harmonic oscillator is a system that, when displaced from its equilibrium position, experiences a restoring force F proportional to the displacement x: $where k is a positive constant.$

$<span class="mw-page-title-main">Phase (waves)</span> The elapsed fraction of a cycle of a periodic function$

In physics and mathematics, the phase of a wave or other periodic function $of some real variable is an angle-like quantity representing the fraction of the cycle covered up to . It is expressed in such a scale that it varies by one full turn as the variable goes through each period. It may be measured in any angular unit such as degrees or radians, thus increasing by 360° or as the variable completes a full period.$

In mathematics, a spherical coordinate system is a coordinate system for three-dimensional space where the position of a given point in space is specified by three real numbers: the radial distance $r$ along the radial line connecting the point to the fixed point of origin; the polar angle $θ$ between the radial line and a given polar axis; and the azimuthal angle $φ$ as the angle of rotation of the radial line around the polar axis. (See graphic regarding the "physics convention".) Once the radius is fixed, the three coordinates (r, θ, φ), known as a 3-tuple, provide a coordinate system on a sphere, typically called the spherical polar coordinates. The plane passing through the origin and perpendicular to the polar axis (where the polar angle is a right angle) is called the reference plane (sometimes fundamental plane).

<span class="mw-page-title-main">Torque</span> Turning force around an axis

In physics and mechanics, torque is the rotational analogue of linear force. It is also referred to as the moment of force. The symbol for torque is typically $, the lowercase Greek letter tau . When being referred to as moment of force, it is commonly denoted by M . Just as a linear force is a push or a pull applied to a body, a torque can be thought of as a twist applied to an object with respect to a chosen point; for example, driving a screw uses torque, which is applied by the screwdriver rotating around its axis. A force of three newtons applied two metres from the fulcrum, for example, exerts the same torque as a force of one newton applied six metres from the fulcrum.$

Dynamic mechanical analysis is a technique used to study and characterize materials. It is most useful for studying the viscoelastic behavior of polymers. A sinusoidal stress is applied and the strain in the material is measured, allowing one to determine the complex modulus. The temperature of the sample or the frequency of the stress are often varied, leading to variations in the complex modulus; this approach can be used to locate the glass transition temperature of the material, as well as to identify transitions corresponding to other molecular motions.

Parabolic coordinates are a two-dimensional orthogonal coordinate system in which the coordinate lines are confocal parabolas. A three-dimensional version of parabolic coordinates is obtained by rotating the two-dimensional system about the symmetry axis of the parabolas.

Hemorheology, also spelled haemorheology, or blood rheology, is the study of flow properties of blood and its elements of plasma and cells. Proper tissue perfusion can occur only when blood's rheological properties are within certain levels. Alterations of these properties play significant roles in disease processes. Blood viscosity is determined by plasma viscosity, hematocrit and mechanical properties of red blood cells. Red blood cells have unique mechanical behavior, which can be discussed under the terms erythrocyte deformability and erythrocyte aggregation. Because of that, blood behaves as a non-Newtonian fluid. As such, the viscosity of blood varies with shear rate. Blood becomes less viscous at high shear rates like those experienced with increased flow such as during exercise or in peak-systole. Therefore, blood is a shear-thinning fluid. Contrarily, blood viscosity increases when shear rate goes down with increased vessel diameters or with low flow, such as downstream from an obstruction or in diastole. Blood viscosity also increases with increases in red cell aggregability.

<span class="mw-page-title-main">Torsion spring</span> Type of spring

A torsion spring is a spring that works by twisting its end along its axis; that is, a flexible elastic object that stores mechanical energy when it is twisted. When it is twisted, it exerts a torque in the opposite direction, proportional to the amount (angle) it is twisted. There are various types:

In materials science, a dislocation or Taylor's dislocation is a linear crystallographic defect or irregularity within a crystal structure that contains an abrupt change in the arrangement of atoms. The movement of dislocations allow atoms to slide over each other at low stress levels and is known as glide or slip. The crystalline order is restored on either side of a glide dislocation but the atoms on one side have moved by one position. The crystalline order is not fully restored with a partial dislocation. A dislocation defines the boundary between slipped and unslipped regions of material and as a result, must either form a complete loop, intersect other dislocations or defects, or extend to the edges of the crystal. A dislocation can be characterised by the distance and direction of movement it causes to atoms which is defined by the Burgers vector. Plastic deformation of a material occurs by the creation and movement of many dislocations. The number and arrangement of dislocations influences many of the properties of materials.

In general relativity, Schwarzschild geodesics describe the motion of test particles in the gravitational field of a central fixed mass $that is, motion in the Schwarzschild metric. Schwarzschild geodesics have been pivotal in the validation of Einstein's theory of general relativity. For example, they provide accurate predictions of the anomalous precession of the planets in the Solar System and of the deflection of light by gravity.$

Precipitation hardening, also called age hardening or particle hardening, is a heat treatment technique used to increase the yield strength of malleable materials, including most structural alloys of aluminium, magnesium, nickel, titanium, and some steels, stainless steels, and duplex stainless steel. In superalloys, it is known to cause yield strength anomaly providing excellent high-temperature strength.

Instantaneous phase and frequency are important concepts in signal processing that occur in the context of the representation and analysis of time-varying functions. The instantaneous phase (also known as local phase or simply phase) of a complex-valued function s(t), is the real-valued function:

The second polar moment of area, also known as "polar moment of inertia" or even "moment of inertia", is a quantity used to describe resistance to torsional deformation (deflection), in objects with an invariant cross-section and no significant warping or out-of-plane deformation. It is a constituent of the second moment of area, linked through the perpendicular axis theorem. Where the planar second moment of area describes an object's resistance to deflection (bending) when subjected to a force applied to a plane parallel to the central axis, the polar second moment of area describes an object's resistance to deflection when subjected to a moment applied in a plane perpendicular to the object's central axis. Similar to planar second moment of area calculations, the polar second moment of area is often denoted as $. While several engineering textbooks and academic publications also denote it as or, this designation should be given careful attention so that it does not become confused with the torsion constant,, used for non-cylindrical objects.$

Prolate spheroidal coordinates are a three-dimensional orthogonal coordinate system that results from rotating the two-dimensional elliptic coordinate system about the focal axis of the ellipse, i.e., the symmetry axis on which the foci are located. Rotation about the other axis produces oblate spheroidal coordinates. Prolate spheroidal coordinates can also be considered as a limiting case of ellipsoidal coordinates in which the two smallest principal axes are equal in length.

<span class="mw-page-title-main">Torsion constant</span> Geometrical property of a bars cross-section

The torsion constant or torsion coefficient is a geometrical property of a bar's cross-section. It is involved in the relationship between angle of twist and applied torque along the axis of the bar, for a homogeneous linear elastic bar. The torsion constant, together with material properties and length, describes a bar's torsional stiffness. The SI unit for torsion constant is m⁴.

The derivation of the Navier–Stokes equations as well as their application and formulation for different families of fluids, is an important exercise in fluid dynamics with applications in mechanical engineering, physics, chemistry, heat transfer, and electrical engineering. A proof explaining the properties and bounds of the equations, such as Navier–Stokes existence and smoothness, is one of the important unsolved problems in mathematics.

The Timoshenko–Ehrenfest beam theory was developed by Stephen Timoshenko and Paul Ehrenfest early in the 20th century. The model takes into account shear deformation and rotational bending effects, making it suitable for describing the behaviour of thick beams, sandwich composite beams, or beams subject to high-frequency excitation when the wavelength approaches the thickness of the beam. The resulting equation is of 4th order but, unlike Euler–Bernoulli beam theory, there is also a second-order partial derivative present. Physically, taking into account the added mechanisms of deformation effectively lowers the stiffness of the beam, while the result is a larger deflection under a static load and lower predicted eigenfrequencies for a given set of boundary conditions. The latter effect is more noticeable for higher frequencies as the wavelength becomes shorter, and thus the distance between opposing shear forces decreases.

The capstan equation or belt friction equation, also known as Euler–Eytelwein formula, relates the hold-force to the load-force if a flexible line is wound around a cylinder.

In Einstein's theory of general relativity, the interior Schwarzschild metric is an exact solution for the gravitational field in the interior of a non-rotating spherical body which consists of an incompressible fluid and has zero pressure at the surface. This is a static solution, meaning that it does not change over time. It was discovered by Karl Schwarzschild in 1916, who earlier had found the exterior Schwarzschild metric.

Propeller theory is the science governing the design of efficient propellers. A propeller is the most common propulsor on ships, and on small aircraft.

References

↑ Escudier, Marcel (2019). A dictionary of mechanical engineering. New Yoek, NY: Oxford University Press. ISBN 978-0-19-883210-2.
↑ Rennie, Richard; Law, Jonathan, eds. (2019-03-21), "A Dictionary of Physics", A Dictionary of Physics, Oxford University Press, doi:10.1093/acref/9780198821472.001.0001/acref-9780198821472, ISBN 978-0-19-882147-2 , retrieved 2024-11-29
↑ Horner, Joseph Gregory (1960). Dictionary of terms used in the theory and practice of mechanical engineering. London: Technical Press.
↑ Weld, Le Roy D. (1937). Glossary of physics. New York London: McGraw-Hill Book Company, Inc.
↑ Lindsay, Robert Bruce (1943). Student's handbook of elementary physics. New York, N.Y.: The Dryden press.
↑ Michels, Walter C. (1956). The International dictionary of physics and electronics. Princeton, N.J.: Van Nostrand.
↑ Seaburg, Paul; Carter, Charles (1997). Torsional Analysis of Structural Steel Members. American Institute of Steel Construction. p. 3.
↑ Case and Chilver "Strength of Materials and Structures
↑ Fakouri Hasanabadi, M.; Kokabi, A.H.; Faghihi-Sani, M.A.; Groß-Barsnick, S.M.; Malzbender, J. (October 2018). "Room- and high-temperature torsional shear strength of solid oxide fuel/electrolysis cell sealing material". Ceramics International. 45 (2): 2219–2225. doi:10.1016/j.ceramint.2018.10.134. ISSN 0272-8842. S2CID 139371841.

External links

The dictionary definition of torsion at Wiktionary
Solid Mechanics at Wikibooks

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[1] Escudier, Marcel (2019). A dictionary of mechanical engineering. New Yoek, NY: Oxford University Press. ISBN 978-0-19-883210-2.

[2] Rennie, Richard; Law, Jonathan, eds. (2019-03-21), "A Dictionary of Physics", A Dictionary of Physics, Oxford University Press, doi:10.1093/acref/9780198821472.001.0001/acref-9780198821472, ISBN 978-0-19-882147-2 , retrieved 2024-11-29

[3] Horner, Joseph Gregory (1960). Dictionary of terms used in the theory and practice of mechanical engineering. London: Technical Press.

[4] Weld, Le Roy D. (1937). Glossary of physics. New York London: McGraw-Hill Book Company, Inc.

[5] Lindsay, Robert Bruce (1943). Student's handbook of elementary physics. New York, N.Y.: The Dryden press.

[6] Michels, Walter C. (1956). The International dictionary of physics and electronics. Princeton, N.J.: Van Nostrand.

[7] Seaburg, Paul; Carter, Charles (1997). Torsional Analysis of Structural Steel Members. American Institute of Steel Construction. p. 3.

[8] Case and Chilver "Strength of Materials and Structures

[9] Fakouri Hasanabadi, M.; Kokabi, A.H.; Faghihi-Sani, M.A.; Groß-Barsnick, S.M.; Malzbender, J. (October 2018). "Room- and high-temperature torsional shear strength of solid oxide fuel/electrolysis cell sealing material". Ceramics International. 45 (2): 2219–2225. doi:10.1016/j.ceramint.2018.10.134. ISSN 0272-8842. S2CID 139371841.

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]