Volcanic ash and aviation safety

Last updated
Volcanic ash from the eruption of Eyjafjallajokull disrupted air travel in Europe in 2010. Eyjafjallajokull 17-4-2010.jpg
Volcanic ash from the eruption of Eyjafjallajökull disrupted air travel in Europe in 2010.

Plumes of volcanic ash near active volcanoes are a flight safety hazard, especially for night flights. Volcanic ash is hard and abrasive, and can quickly cause significant wear to propellers and turbocompressor blades, and scratch cockpit windows, impairing visibility. The ash contaminates fuel and water systems, can jam gears, and make engines flame out. Its particles have low melting points and readily melt in the engines' combustion chambers; this creates a ceramic mass that sticks to turbine blades, fuel nozzles, and combustors, which can quickly lead to total engine failure. Ash can also contaminate the cabin and damage avionics. [1] [2]

Contents

In 1991, the aviation industry decided to set up Volcanic Ash Advisory Centers (VAACs) for liaison between meteorologists, volcanologists, and the aviation industry. [3] Before 2010, aircraft engine manufacturers had not defined specific particle levels above which they considered engines at risk. Airspace regulators took the general approach that if ash concentration rose above zero, they considered airspace unsafe, and consequently closed it. [4]

The costs of air travel disruption in Europe after a volcanic eruption in 2010 forced aircraft manufacturers to specify limits on how much ash they considered acceptable for a jet engine to ingest without damage. In April, the UK CAA, in conjunction with engine manufacturers, set the safe upper limit of ash density at 2 mg per cubic metre of air space. [5] From May 2010, the CAA revised the safe limit upwards to 4 mg per cubic metre of air space. [6]

To minimise further disruption that this and other volcanic eruptions could cause, the CAA created a new category of restricted airspace called a Time Limited Zone. [7] Airspace categorised as TLZ is similar to airspace under severe weather conditions, in that restrictions should be of a short duration. However, a key difference with TLZ airspace is that airlines must produce certificates of compliance for aircraft they want to enter these areas. Any airspace where ash density exceeds 4 mg per cubic metre is prohibited airspace.[ citation needed ]

Volcanic ash in the immediate vicinity of the eruption plume is different in particle size range and density than that in downwind dispersal clouds, which contain only the finest particle sizes of ash. Experts have not established the ash loading that affects normal engine operation (other than engine lifetime and maintenance costs). Whether this silica-melt risk remains at the much lower ash densities characteristic of downstream ash clouds is currently unclear.[ citation needed ]

Experts recognised that there was an issue following British Airways Flight 9 in 1982, and therefore the ICAO established the Volcanic Ash Warning Study Group. Due to the difficulty in forecasting accurate information out to 12 hours and beyond, the ICAO later set up Volcanic Ash Advisory Centers (VAACs). [8] [9]

Volcanic hazards to aviation

Volcanic ash consists of small tephra, which are bits of pulverized rock and glass less than 2 millimetres (0.079 in) in diameter created by volcanic eruptions. [10] The ash enters the atmosphere from the force of the eruption and convection currents from the heated air, and is then carried away from the volcano by winds. The ash with the smallest size can remain in the atmosphere for a considerable period of time, and can drift away from the eruption point. The ash cloud can be dangerous to aviation if it reaches the heights of aircraft flight paths.

Ash cloud from the 2008 eruption of Chaiten volcano stretching across Patagonia from the Pacific to the Atlantic Ocean Plume from eruption of Chaiten volcano, Chile.jpg
Ash cloud from the 2008 eruption of Chaitén volcano stretching across Patagonia from the Pacific to the Atlantic Ocean

Pilots can't see ash clouds at night. Also, ash particles are too small to return an echo to on-board weather radars on commercial airliners. Even when flying in daylight, pilots may interpret a visible ash cloud as a normal cloud of water vapour and not a danger—especially if the ash has travelled far from the eruption site. [8] [11] In the image from the Chaitén volcano, the ash cloud has spread thousands of kilometers from the eruption site, crossing the width of South America from the Pacific coast and spreading over the Atlantic.

Volcanic ash has a melting point of approximately 1,100 °C (2,010 °F), which is below the operating temperature of modern commercial jet engines, about 1,400 °C (2,550 °F). Volcanic ash can damage gas turbines in a number of ways. These can be categorised into those that pose an immediate hazard to the engines and those that present a maintenance problem.

Immediate hazards to aircraft

Volcanic ash deposits on a parked McDonnell-Douglas DC-10-30 during the 1991 eruption of Mount Pinatubo, causing the aircraft to rest on its tail. While falling ash behaves in a similar manner to snow, the sheer weight of deposits can cause serious damage to buildings and vehicles, as seen here, where the deposits were able to cause the 120 ton airliner's centre of gravity to shift. DC-10-30 resting on its tail due to Pinatubo ashfall.jpg
Volcanic ash deposits on a parked McDonnell-Douglas DC-10-30 during the 1991 eruption of Mount Pinatubo, causing the aircraft to rest on its tail. While falling ash behaves in a similar manner to snow, the sheer weight of deposits can cause serious damage to buildings and vehicles, as seen here, where the deposits were able to cause the 120 ton airliner's centre of gravity to shift.

Volcanic ash is composed of fragments of rock, crystalline material, and volcanic glass. The glass component has the lowest melting temperature—lower than temperatures inside the combustor of a gas turbine engine. Ash that finds its way into the combustor may melt. Combustor and turbine components are cooled, as the metals they are made of have lower melting temperatures than the gas temperature inside the engine core. Molten ash that touches these surfaces is likely to freeze, and accrete on the metal surface.

The most sensitive surface is the high-pressure turbine nozzle guide vanes (NGVs), situated immediately downstream of the combustor. The gas flow is choked through the NGVs, and so the flow area through the NGVs is a controlling area for the engine. If this area is reduced due to an accretion of ash, a smaller mass flow rate of gas passes through the engine core. Reduced mass flow leads to the turbine doing less work. The turbine drives the compressor, which accordingly also does less work compressing the air. If the compressor can no longer contain the high pressure gas in the engine core, the gas flow can reverse and flow out of the front of the engine. This is known as an engine surge or a compressor surge, and is often accompanied by a ball of flame that bursts out the front of the engine. This surge is likely to extinguish the flame in the engine combustor, known as a 'flame-out'. Once the high pressure in the core dissipates, the engine should be free to restart. Restarting an engine at altitude can be difficult, due to the lower temperatures and pressures of the ambient gas, but is not normally a problem. The reduced flow area of the NGVs can make it harder to restart the engine.

Volcanic ash carries significant electrostatic charge. Fine ash that enters electronic components within the engine or airframe can cause electrical failure—which poses an immediate hazard to the aircraft. [12]

Ash-induced problems requiring increased maintenance

  1. Volcanic ash, as a hard substance, damages gas turbine compressors. It erodes by impacting compressor blades and vanes and removing material—and abrades by three body interactions between the rotating blade, ash particle, and compressor annulus. Changing the shapes of the blades and vanes and increasing gaps between blades and annuli both help reduce engine fuel efficiency and operability.
  2. Molten ash that sticks to cooled surfaces can block cooling holes. This stops cooling air flow and heats surrounding metal, leading to accelerated thermal fatigue. This process affects combustor and turbine components.
  3. Ash can accumulate and partially block fuel spray nozzles, impairing air and fuel flow fields and mixture stoichiometries in the combustor. Such adverse conditions reduce engine performance and can create local hot spots that increase the combuster's thermal fatigue rate. [12]

Sulfur dioxide clouds

Sulfur dioxide—another product of volcanoes that is carried in ash clouds after an eruption—is corrosive to aircraft that fly through it. [8]

There has been an attempt to prove that the sulphur dioxide usually accompanying a volcanic eruption is indeed a good indication of the presence of ash clouds such as to facilitate avoidance of ash clouds in aviation.

However, it has been found that the two species of clouds tend to separate due to windshear. Additionally, the detection methods have limitations, as both species have the potential to be masked by other types of aerosol, such as water or ice; this contributes to great variability in the data.

Therefore, as there is no consistent overlap between SO2 and the ash, SO2 is not a reliable indicator for ash clouds. [13]

Accidents and incidents

In 1982, British Airways Flight 9 was a flight from London to Auckland. During the Kuala Lumpur to Perth section of its journey, the Boeing 747-200 aircraft flew through an ash cloud of Mount Galunggung, losing power from all four engines, and descended from 37,000 feet (11,000 m) to only 13,500 feet (4,100 m) before the flight crew managed to restart three of the engines and land at Jakarta.

In 1989, KLM Flight 867 was a flight from Amsterdam to Tokyo via Anchorage. On descent into Anchorage, the aircraft was descending through 24,000 feet (7,300 m) and the 747-400 encountered the ash cloud from Mount Redoubt and all four engines failed. At 13,000 feet (4,000 m), the two left engines restarted and at 11,000 feet (3,400 m), the two remaining engines restarted. Minutes after, the aircraft made a successful emergency landing at Ted Stevens International Airport, Anchorage.

Related Research Articles

<span class="mw-page-title-main">Volcano</span> Rupture in a planets crust where material escapes

A volcano is a rupture in the crust of a planetary-mass object, such as Earth, that allows hot lava, volcanic ash, and gases to escape from a magma chamber below the surface. The process that forms volcanoes is called volcanism.

<span class="mw-page-title-main">Turbofan</span> Airbreathing jet engine designed to provide thrust by driving a fan

A turbofan or fanjet is a type of airbreathing jet engine that is widely used in aircraft propulsion. The word "turbofan" is a combination of references to the preceding generation engine technology of the turbojet and the additional fan stage. It consists of a gas turbine engine which achieves mechanical energy from combustion, and a ducted fan that uses the mechanical energy from the gas turbine to force air rearwards. Thus, whereas all the air taken in by a turbojet passes through the combustion chamber and turbines, in a turbofan some of that air bypasses these components. A turbofan thus can be thought of as a turbojet being used to drive a ducted fan, with both of these contributing to the thrust.

<span class="mw-page-title-main">Stratovolcano</span> Type of conical volcano composed of layers of lava and tephra

A stratovolcano, also known as a composite volcano, is a conical volcano built up by many alternating layers (strata) of hardened lava and tephra. Unlike shield volcanoes, stratovolcanoes are characterized by a steep profile with a summit crater and explosive eruptions. Some have collapsed summit craters called calderas. The lava flowing from stratovolcanoes typically cools and solidifies before spreading far, due to high viscosity. The magma forming this lava is often felsic, having high to intermediate levels of silica, with lesser amounts of less viscous mafic magma. Extensive felsic lava flows are uncommon, but can travel as far as 8km (5mi).

<span class="mw-page-title-main">Turbojet</span> Airbreathing jet engine which is typically used in aircraft

The turbojet is an airbreathing jet engine which is typically used in aircraft. It consists of a gas turbine with a propelling nozzle. The gas turbine has an air inlet which includes inlet guide vanes, a compressor, a combustion chamber, and a turbine. The compressed air from the compressor is heated by burning fuel in the combustion chamber and then allowed to expand through the turbine. The turbine exhaust is then expanded in the propelling nozzle where it is accelerated to high speed to provide thrust. Two engineers, Frank Whittle in the United Kingdom and Hans von Ohain in Germany, developed the concept independently into practical engines during the late 1930s.

A combustor is a component or area of a gas turbine, ramjet, or scramjet engine where combustion takes place. It is also known as a burner, burner can, combustion chamber or flame holder. In a gas turbine engine, the combustor or combustion chamber is fed high-pressure air by the compression system. The combustor then heats this air at constant pressure as the fuel/air mix burns. As it burns the fuel/air mix heats and rapidly expands. The burned mix is exhausted from the combustor through the nozzle guide vanes to the turbine. In the case of ramjet or scramjet engines, the exhaust is directly fed out through the nozzle.

<span class="mw-page-title-main">Eruption column</span> A cloud of hot ash and volcanic gases emitted during an explosive volcanic eruption

An eruption column or eruption plume is a cloud of super-heated ash and tephra suspended in gases emitted during an explosive volcanic eruption. The volcanic materials form a vertical column or plume that may rise many kilometers into the air above the vent of the volcano. In the most explosive eruptions, the eruption column may rise over 40 km (25 mi), penetrating the stratosphere. Stratospheric injection of aerosols by volcanoes is a major cause of short-term climate change.

<span class="mw-page-title-main">Volcanic gas</span> Gases given off by active volcanoes

Volcanic gases are gases given off by active volcanoes. These include gases trapped in cavities (vesicles) in volcanic rocks, dissolved or dissociated gases in magma and lava, or gases emanating from lava, from volcanic craters or vents. Volcanic gases can also be emitted through groundwater heated by volcanic action.

A jet engine performs by converting fuel into thrust. How well it performs is an indication of what proportion of its fuel goes to waste. It transfers heat from burning fuel to air passing through the engine. In doing so it produces thrust work when propelling a vehicle but a lot of the fuel is wasted and only appears as heat. Propulsion engineers aim to minimize the degradation of fuel energy into unusable thermal energy. Increased emphasis on performance improvements for commercial airliners came in the 1970s from the rising cost of fuel.

<span class="mw-page-title-main">Turbine blade</span> Aerofoil; individual component of a turbine disc

A turbine blade is a radial aerofoil mounted in the rim of a turbine disc and which produces a tangential force which rotates a turbine rotor. Each turbine disc has many blades. As such they are used in gas turbine engines and steam turbines. The blades are responsible for extracting energy from the high temperature, high pressure gas produced by the combustor. The turbine blades are often the limiting component of gas turbines. To survive in this difficult environment, turbine blades often use exotic materials like superalloys and many different methods of cooling that can be categorized as internal and external cooling, and thermal barrier coatings. Blade fatigue is a major source of failure in steam turbines and gas turbines. Fatigue is caused by the stress induced by vibration and resonance within the operating range of machinery. To protect blades from these high dynamic stresses, friction dampers are used.

<span class="mw-page-title-main">Components of jet engines</span> Brief description of components needed for jet engines

This article briefly describes the components and systems found in jet engines.

A Volcanic Ash Advisory Center (VAAC) is a group of experts responsible for coordinating and disseminating information on atmospheric volcanic ash clouds that may endanger aviation. As at 2019, there are nine Volcanic Ash Advisory Centers located around the world, each one focusing on a particular geographical region. Their analyses are made public in the form of volcanic ash advisories (VAAs), involving expertise analysis of satellite observations, ground and pilot observations and interpretation of ash dispersion models.

<span class="mw-page-title-main">Maritime impacts of volcanic eruptions</span>

Volcanic eruptions can have various impacts on maritime transportation. When a volcano erupts, large amounts of noxious gases, steam, rock, and ash are released into the atmosphere; fine ash can be transported thousands of miles from the volcano, while high concentrations of coarse particles fall out of the air near the volcano. The high concentrations of hazardous toxic gases are localized in the immediate vicinity of the volcano.

<span class="mw-page-title-main">Volcanic hazard</span> Probability of a volcanic eruption or related geophysical event

A volcanic hazard is the probability a volcanic eruption or related geophysical event will occur in a given geographic area and within a specified window of time. The risk that can be associated with a volcanic hazard depends on the proximity and vulnerability of an asset or a population of people near to where a volcanic event might occur.

<span class="mw-page-title-main">2010 eruptions of Eyjafjallajökull</span> Volcanic events in Iceland

Between March and June 2010 a series of volcanic events at Eyjafjallajökull in Iceland caused enormous disruption to air travel across Western Europe.

<span class="mw-page-title-main">Air travel disruption after the 2010 Eyjafjallajökull eruption</span> Disruption of air travel due to volcanic ash

In response to concerns that volcanic ash ejected during the 2010 eruptions of Eyjafjallajökull in Iceland would damage aircraft engines, the controlled airspace of many European countries was closed to instrument flight rules traffic, resulting in what at the time was the largest air-traffic shut-down since World War II. The closures caused millions of passengers to be stranded not only in Europe, but across the world. With large parts of European airspace closed to air traffic, many more countries were affected as flights to, from, and over Europe were cancelled.

An airbreathing jet engine is a jet engine in which the exhaust gas which supplies jet propulsion is atmospheric air, which is taken in, compressed, heated, and expanded back to atmospheric pressure through a propelling nozzle. Compression may be provided by a gas turbine, as in the original turbojet and newer turbofan, or arise solely from the ram pressure of the vehicle's velocity, as with the ramjet and pulsejet.

<span class="mw-page-title-main">2010 eruptions of Mount Merapi</span> Volcanic eruption of Mount Merapi in Indonesia

In late October 2010, Mount Merapi in border of Central Java and Special Region of Yogyakarta, Indonesia began an increasingly violent series of eruptions that continued into November. Seismic activity around the volcano increased from mid-September onwards, culminating in repeated outbursts of lava and volcanic ash. Large eruption columns formed, causing numerous pyroclastic flows down the heavily populated slopes of the volcano. The 2010 eruption of Merapi was the volcano's largest since 1872.

<span class="mw-page-title-main">Volcanic ash</span> Natural material created during volcanic eruptions

Volcanic ash consists of fragments of rock, mineral crystals, and volcanic glass, produced during volcanic eruptions and measuring less than 2 mm (0.079 inches) in diameter. The term volcanic ash is also often loosely used to refer to all explosive eruption products, including particles larger than 2 mm. Volcanic ash is formed during explosive volcanic eruptions when dissolved gases in magma expand and escape violently into the atmosphere. The force of the gases shatters the magma and propels it into the atmosphere where it solidifies into fragments of volcanic rock and glass. Ash is also produced when magma comes into contact with water during phreatomagmatic eruptions, causing the water to explosively flash to steam leading to shattering of magma. Once in the air, ash is transported by wind up to thousands of kilometres away.

Aircraft engine performance refers to factors including thrust or shaft power for fuel consumed, weight, cost, outside dimensions and life. It includes meeting regulated environmental limits which apply to emissions of noise and chemical pollutants, and regulated safety aspects which require a design that can safely tolerate environmental hazards such as birds, rain, hail and icing conditions. It is the end product that an engine company sells.

References

  1. ↑ "USGS: Volcano Hazards Program". volcanoes.usgs.gov.
  2. ↑ "Volcanic Ash - SKYbrary Aviation Safety". www.skybrary.aero.
  3. ↑ "Volcanic Ash–Danger to Aircraft in the North Pacific, USGS Fact Sheet 030-97". pubs.usgs.gov.
  4. ↑ "Can we fly safely through volcanic ash?".
  5. ↑ Marks, Paul (2010-04-21). "Engine strip-downs establish safe volcanic ash levels". New Scientist. Retrieved 2019-11-12.
  6. ↑ "UK ash cloud restrictions lifted". BBC News. May 17, 2010.
  7. ↑ "Changes to the operating procedures in the vicinity of high ash concentration areas" (PDF). Archived from the original (PDF) on 2010-05-22. Retrieved 2010-05-18.
  8. 1 2 3 "Overview of VAAC SACS workshop October 2006".[ permanent dead link ]
  9. ↑ "International Airways Volcano Watch Programme".
  10. ↑ "USGS: Volcano Hazards Program". volcanoes.usgs.gov.
  11. ↑ Video on Dangers of Volcanic Ash by International Federation of Airline Pilots Associations
  12. 1 2 Institute of Mechanical Engineers Symposium: Aviation Safety in Volcanic Ash Clouds: Progress since E15. Nov 2013
  13. ↑ Sears, T. M.; Thomas, G. E.; Carboni, E.; Smith, A. J. A.; Grainger, R. G. (2013). "SO2 as a possible proxy for volcanic ash in aviation hazard avoidance". Journal of Geophysical Research: Atmospheres. 18 (11): 5698–5709. Bibcode:2013JGRD..118.5698S. doi: 10.1002/jgrd.50505 .
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.