A modeline is a configuration line in xorg.conf or the XFree86 configuration file (XF86Config) that provides information to the display server about a connected computer monitor or television and how to drive it at a specified display resolution. The Modeline is based on the Generalized Timing Formula or the Coordinated Video Timings standards produced by VESA.
Modelines are now rarely used, but XFree86 and the Xorg Server still allow them to be set should the EDID information be inadequate.
Each modeline has ten parameters, beginning with a label for the resolution being specified. The second parameter specifies the rate of the pixel clock in megahertz. Then follow four numbers that together specify the x-resolution (width) and related parameters, and four numbers that specify the y-resolution (height).
Modeline"1600x1200" 155 1600 1656 1776 2048 1200 1202 1205 1263# (Label) (clk) (x-resolution) (y-resolution)# |# (pixel clock in MHz)
Or, the modeline can be split into multiple lines for greater clarity
Modeline"1600x1200" 155 1600 1656 1776 204812001202 1205 1263
The horizontal and vertical frequencies can be calculated by:
For interlace mode, (frame rate)=(field rate)/2, otherwise (frame rate)=(field rate).
The numbers after the width and height are used to determine the front porch, sync pulse, and back porch timings. The resulting refresh rate or frame rate of the display can be determined by dividing the pixel clock frequency by the product of the horizontal and vertical field lengths. In this case, the display is operating at Hz.
Optionally, extra parameters for controlling the polarity of the horizontal and vertical sync pulses can be added. There are also options for interlaced and double scan modes. In most situations they will not be required.
Modelines may no longer be necessary in XFree86 versions 4 and higher, [1] since for many monitors and HDTVs they are now calculated by the X server at startup based on two factors:
EDID is not always completely accurate, and for some situations such as older or unusual display hardware or many HDTVs, it will be necessary to create a modeline to get the setting right. The EDID information can be obtained by using the command "startx -- -logverbose 6
" and looking at /var/log/XFree86.0.log.
The Original Chip Set (OCS) is a chipset used in the earliest Commodore Amiga computers and defined the Amiga's graphics and sound capabilities. It was succeeded by the slightly improved Enhanced Chip Set (ECS) and greatly improved Advanced Graphics Architecture (AGA).
Digital Visual Interface (DVI) is a video display interface developed by the Digital Display Working Group (DDWG). The digital interface is used to connect a video source, such as a video display controller, to a display device, such as a computer monitor. It was developed with the intention of creating an industry standard for the transfer of uncompressed digital video content.
Video Graphics Array (VGA) is a video display controller and accompanying de facto graphics standard, first introduced with the IBM PS/2 line of computers in 1987, which became ubiquitous in the IBM PC compatible industry within three years. The term can now refer to the computer display standard, the 15-pin D-subminiature VGA connector, or the 640 × 480 resolution characteristic of the VGA hardware.
Extended Display Identification Data (EDID) and Enhanced EDID (E-EDID) are metadata formats for display devices to describe their capabilities to a video source. The data format is defined by a standard published by the Video Electronics Standards Association (VESA).
The Display Data Channel, or DDC, is a collection of protocols for digital communication between a computer display and a graphics adapter that enable the display to communicate its supported display modes to the adapter and that enable the computer host to adjust monitor parameters, such as brightness and contrast.
The refresh rate, also known as vertical refresh rate or vertical scan rate in reference to terminology originating with the cathode-ray tubes (CRTs), is the number of times per second that a raster-based display device displays a new image. This is independent from frame rate, which describes how many images are stored or generated every second by the device driving the display. On CRT displays, higher refresh rates produce less flickering, thereby reducing eye strain. In other technologies such as liquid-crystal displays, the refresh rate affects only how often the image can potentially be updated.
X.Org Server is the free and open-source implementation of the X Window System display server stewarded by the X.Org Foundation.
The display resolution or display modes of a digital television, computer monitor or display device is the number of distinct pixels in each dimension that can be displayed. It can be an ambiguous term especially as the displayed resolution is controlled by different factors in cathode ray tube (CRT) displays, flat-panel displays and projection displays using fixed picture-element (pixel) arrays.
The Motorola 6845, or MC6845, is a display controller that was widely used in 8-bit computers during the 1980s. Originally intended for designs based on the Motorola 6800 CPU and given a related part number, it was more widely used alongside various other processors, and was most commonly found in machines based on the Zilog Z80 and MOS 6502.
480i is the video mode used for standard-definition digital video in the Caribbean, Japan, South Korea, Taiwan, Philippines, Western Sahara, and most of the Americas. The other common standard definition digital standard, used in the rest of the world, is 576i.
The configuration file XF86Config of the XFree86 project is used by the X server to set necessary configuration parameters.
The native resolution of an liquid crystal display (LCD), liquid crystal on silicon (LCoS) or other flat panel display refers to its single fixed resolution. As an LCD consists of a fixed raster, it cannot change resolution to match the signal being displayed as a cathode-ray tube (CRT) monitor can, meaning that optimal display quality can be reached only when the signal input matches the native resolution. An image where the number of pixels is the same as in the image source and where the pixels are perfectly aligned to the pixels in the source is said to be pixel perfect.
A raster scan, or raster scanning, is the rectangular pattern of image capture and reconstruction in television. By analogy, the term is used for raster graphics, the pattern of image storage and transmission used in most computer bitmap image systems. The word raster comes from the Latin word rastrum, which is derived from radere ; see also rastrum, an instrument for drawing musical staff lines. The pattern left by the lines of a rake, when drawn straight, resembles the parallel lines of a raster: this line-by-line scanning is what creates a raster. It is a systematic process of covering the area progressively, one line at a time. Although often a great deal faster, it is similar in the most general sense to how one's gaze travels when one reads lines of text.
Resolution independence is where elements on a computer screen are rendered at sizes independent from the pixel grid, resulting in a graphical user interface that is displayed at a consistent physical size, regardless of the resolution of the screen.
Coordinated Video Timings is a standard by VESA which defines the timings of the component video signal. Initially intended for use by computer monitors and video cards, the standard made its way into consumer televisions.
A multiple-sync (multisync) monitor, also known as a multiscan or multimode monitor, is a raster-scan analog video monitor that can properly synchronise with multiple horizontal and vertical scan rates. In contrast, fixed frequency monitors can only synchronise with a specific set of scan rates. They are generally used for computer displays, but sometimes for television, and the terminology is mostly applied to CRT displays although the concept applies to other technologies.
Display lag is a phenomenon associated with most types of liquid crystal displays (LCDs) like smartphones and computers and nearly all types of high-definition televisions (HDTVs). It refers to latency, or lag between when the signal is sent to the display and when the display starts to show that signal. This lag time has been measured as high as 68 ms, or the equivalent of 3-4 frames on a 60 Hz display. Display lag is not to be confused with pixel response time, which is the amount of time it takes for a pixel to change from one brightness value to another. Currently the majority of manufacturers quote the pixel response time, but neglect to report display lag.
Generalized Timing Formula is a standard by VESA which defines exact parameters of the component video signal for analogue VGA display interface.
DisplayID is a VESA standard for metadata describing display device capabilities to the video source. It is designed to replace E-EDID standard and EDID structure v1.4.
The graphics display resolution is the width and height dimension of an electronic visual display device, measured in pixels. This information is used for electronic devices such as a computer monitor. Certain combinations of width and height are standardized and typically given a name and an initialism which is descriptive of its dimensions. A graphics display resolution can be used in tandem with the size of the graphics display to calculate pixel density. An increase in the pixel density often correlates with a decrease in the size of individual pixels on a display.