Airfield traffic pattern

Last updated February 26, 2024

An airfield traffic pattern is a standard path followed by aircraft when taking off or landing while maintaining visual contact with the airfield.

At an airport, the pattern (or circuit) is a standard path for coordinating air traffic. It differs from "straight-in approaches" and "direct climb-outs" in that an aircraft using a traffic pattern remains close to the airport. Patterns are usually employed at small general aviation (GA) airfields and military airbases. Many large controlled airports avoid the system unless there is GA activity as well as commercial flights. However, some kind of a pattern may be used at airports in some cases such as when an aircraft is required to go around, but this kind of pattern at controlled airports may be very different in form, shape, and purpose to the standard traffic pattern as used at GA airports.

The use of a pattern at airfields is for aviation safety. By using a consistent flight pattern, pilots will know from where to expect other air traffic and be able to see and avoid it. Pilots flying under visual flight rules (VFR) may not be separated by air traffic control, so this consistent predictable pattern is a vital way to keep things orderly. At tower-controlled airports, air traffic control (ATC) may provide traffic advisories for VFR flights on a work-load permitting basis.

Wind direction

Pilots prefer to take off and land facing into the wind. This has the effect of reducing the aircraft's speed over the ground (for a given airspeed), thus reducing the length of runway required to perform either maneuver.

An exception to this rule is at airports where the runway is on a severe slope, such as alpine airports (altiports). In these instances, takeoffs are usually made downhill and landings uphill regardless of wind direction with the slope aiding in acceleration and deceleration. Another exception is at airports with mountains at one end.

Many airfields have runways facing a variety of directions. The purpose of this is to provide arriving aircraft with the best runway to land on according to the wind direction. Runway orientation is determined from historical data of the prevailing winds in the area. This is especially important for single-runway airports that do not have the option of a second runway pointed in an alternative direction. A common scenario is to have two runways arranged at or close to 90 degrees to one another, so that aircraft can always find a suitable runway. Almost all runways are reversible, and aircraft use whichever runway in whichever direction is best suited to the wind. In light and variable wind conditions, the direction of the runway in use might change several times during the day, or there may be a preferred “calm wind runway”, possibly because it’s longer.^[1]

Layout

Traffic patterns can be defined as left-hand or right-hand according to which way the turns in the pattern are performed. They are usually left-hand turns because most small airplanes are piloted from the left seat (or the senior pilot or pilot-in-command sits in the left seat), and so the pilot has better visibility out the left window. Right-hand patterns will be set up for parallel runways, for noise abatement, or because of ground features (such as terrain, towers, etc.). In the US, the non-standard (i.e. right-hand) patterns are noted in the Airport/Facilities Directory or on a sectional chart; in other countries they may be indicated in that nation's similar document, e.g. Canada Flight Supplement. Unless explicitly indicated otherwise, all traffic patterns at non-towered airports are to the left. The direction of the pattern may be indicated by a traffic pattern indicator in the aerodrome's signal square.

In the United States, the Code of Federal Regulations CFR 91.126 a. (2) requires helicopters to avoid the flow of fixed wing aircraft.^[2]

Because the active runway is chosen to meet the wind at the nearest angle (with take-offs and landings upwind), the pattern orientation also depends on wind direction. Patterns are typically rectangular in basic shape, and include the runway along one long side of the rectangle. Each leg of the pattern has a particular name:^[3]

Upwind leg. A flight path parallel to and in the direction of the landing runway. It is offset from the runway and opposite the downwind leg.
Crosswind leg. A short climbing flight path at right angles to the departure end of the runway.
Downwind leg. A long level flight path parallel to but in the opposite direction of the landing runway. (Some^{[ who? ]} consider it to have "sub-legs" of early, mid and late. Certainly a plane giving a position report of "mid-downwind" can be visually located easily.)
Base leg. A short descending flight path at right angles to the approach end extended centerline of the landing runway.
Final approach . A descending flight path in the direction of landing along the extended runway centerline from the base leg to the runway. The last section of the final approach is sometimes referred to as short final.
Departure leg, Initial,^[4] or Climb out. The climbing flight path along the extended runway centerline which begins at takeoff and continues to at least 1/2 mile beyond the runway's departure end and not less than 300 feet below the traffic pattern altitude.

The names of the legs are logical and based on the relative wind as seen looking down a runway facing into the wind. An aircraft flying upwind heads into the wind, flying crosswind heads across the wind, flying downwind heads in the direction of the wind just like blown smoke.

While many airfields operate a completely standard pattern, in other cases it will be modified according to need. For example, military airfields often dispense with the crosswind and base legs, but rather fly these as circular arcs directly joining the upwind and downwind sections.

Procedures in the pattern

Aircraft are expected to join and leave the pattern, following the pattern already in use. Sometimes this will be at the discretion of the pilot, while at other times the pilot will be directed by air traffic control.

Entering a traffic pattern in the United States

Preferred — Entry-Crossing Midfield

Alternative Midfield Entry, used only when the airfield is not busy.

The U.S. recommend entering a traffic pattern midfield when coming from the upwind leg side.^[5]

There are conventions for joining the pattern, used in different jurisdictions.

In the United States, aircraft usually join the pattern at a 45° angle to the downwind leg and abeam midfield. Although aircraft may legally join the pattern at any point, the AIM and AC 90-66B strongly recommend using a 45° entry at pattern altitude.
In Canada, aircraft at uncontrolled airports usually cross the airport at midfield at pattern altitude from the upwind side, turning onto the downwind leg. Although joining straight in downwind is also a possibility.^[6] At controlled airports, the tower typically directs aircraft to join the downwind leg, base leg, or straight into the final leg.^[7]
In the UK, South Africa, and New Zealand a standard overhead join is recommended.^[8]
In Europe, aircraft usually join the pattern at a 45° angle to the downwind leg, in the beginning of the downwind leg.^{[ citation needed ]}
Fast aircraft, for example military jets, may enter the pattern with a run-and-break (in the US, overhead maneuver or overhead break). The aircraft flies at speed along the final leg, and makes a sharp, high-G turn above midfield to lose speed and arrive on the downwind leg at pattern altitude and in landing configuration.

Similarly, there are conventions for departing the pattern.

In the United States, aircraft usually depart the pattern either straight out along the runway heading, with a 45° turn in the direction of (or against) the crosswind leg, downwind, or with a 45° turn away from downwind.^[9]
In Canada, aircraft usually depart straight out along the runway heading until at circuit altitude, at which point they may turn as desired. At controlled airports, the tower typically gives instructions for what turn to make on departure.^{[ citation needed ]}

There is also a procedure known as an "orbit", where an aircraft flies a 360° loop either clockwise or anticlockwise. This is usually to allow greater separation with other traffic ahead in the pattern. This can be the result of a controller's instruction. If at the pilot's initiative, the pilot will report e.g. "(tail number or flight number) making one left-hand orbit, will advise complete".

To practice take off and landing, a pilot would often fly many patterns, one after another, from the same runway. Upon each landing, depending on the runway distance remaining, aircraft and pilot capabilities, noise abatement procedures in effect, and air traffic control clearance, the pilot will perform either a full stop landing (taxi to the runway beginning for subsequent take-off), a touch-and-go (stabilize in the landing roll, reconfigure the aircraft for take-off, and take-off without ever stopping the aircraft), or a stop-and-go (decelerate to a stop, then take-off from the remaining runway). In the U.S., when operating in a controlled airport a pilot can be cleared for the option, allowing any of the landing options above, or a rejected landing, at pilot's discretion.^[10]

Contra-rotating circuit patterns

In cases where two or more parallel runways are in operation concurrently, the aircraft operating on the outermost runways are required to perform their patterns in a direction which will not conflict with the other runways. Thus, one runway may be operating with a left-hand pattern direction and the other one will be operating with a right-hand pattern direction.

This allows aircraft to maintain maximum separation during their patterns, however it is important that the aircraft do not stray past the centerline of the runway when joining the final leg, so as to avoid potential collisions. If three or more parallel runways exist, as is the case at Bankstown Airport in Australia, then the middle runway(s) can, for obvious reasons, only be used when either a straight in approach is used or when the aircraft joins the pattern from a very wide base leg.

Altitudes

An aerodrome publishes a "circuit height" or "pattern altitude", that is, a nominal level above the field at which pilots are required (recommended in the US, FAA AC90-66A Para. 8c^[9]) to fly while in the circuit. Unless otherwise specified, the standard recommended pattern height is 1000 ft AGL (above ground level), although a pattern height of 800 ft AGL is common. Helicopters usually fly the pattern at 500 ft AGL. Extreme caution must be exercised by pilots while flying at or through published traffic pattern altitudes as this might contribute to mid-air collisions.

Visual indicators

At airports without an operating control tower, a segmented circle visual indicator system, if installed, is designed to provide traffic pattern information. Usually located in a position affording maximum visibility to pilots in the air and on the ground and providing a centralized location for other elements of the system, the segmented circle consists of the following components: wind direction indicators such as windsocks, landing direction indicators, landing strip indicators, and traffic pattern indicators.^[11]

Landing strip indicators are installed in pairs and are used to show the alignment of landing strips. Traffic pattern indicators are arranged in pairs in conjunction with landing strip indicators and used to indicate the direction of turns when there is a variation from the normal left traffic pattern. If there is no segmented circle installed at the airport, traffic pattern indicators may be installed on or near the end of the runway.^[11]

Helicopters

Helicopter pilots also prefer to land facing the wind and are often asked to fly a pattern on arrival or departure. Many airfields operate a special pattern for helicopters to take account of their low airspeed. This is usually a mirror image of the fixed-wing pattern, and often at a slightly lower standard height above surface level; as noted above this altitude is usually 500 feet above ground level. However, due to helicopters' unique maneuverability, helicopter pilots often choose not to enter the pattern, and make a direct approach to the helipad or apron they wish to land on.

Other patterns

If an aircraft intending to land must be delayed, the air traffic control (ATC) may decide to place it in a holding pattern until the airport is prepared to permit the landing. Commercial aircraft on hold will generally fly slow, racetrack-shaped patterns which differ considerably from the airfield traffic pattern that will be commenced once the approval has been given to land. Although an aircraft in a holding pattern may similarly circle the airport, ATC may designate a distant location in which to circle.

Related Research Articles

An airport is an aerodrome with extended facilities, mostly for commercial air transport. Airports usually consist of a landing area, which comprises an aerially accessible open space including at least one operationally active surface such as a runway for a plane to take off and to land or a helipad, and often includes adjacent utility buildings such as control towers, hangars and terminals, to maintain and monitor aircraft. Larger airports may have airport aprons, taxiway bridges, air traffic control centres, passenger facilities such as restaurants and lounges, and emergency services. In some countries, the US in particular, airports also typically have one or more fixed-base operators, serving general aviation.

According to the International Civil Aviation Organization (ICAO), a runway is a "defined rectangular area on a land aerodrome prepared for the landing and takeoff of aircraft". Runways may be a human-made surface or a natural surface. Runways, taxiways and ramps, are sometimes referred to as "tarmac", though very few runways are built using tarmac. Takeoff and landing areas defined on the surface of water for seaplanes are generally referred to as waterways. Runway lengths are now commonly given in meters worldwide, except in North America where feet are commonly used.

Landing is the last part of a flight, where a flying animal, aircraft, or spacecraft returns to the ground. When the flying object returns to water, the process is called alighting, although it is commonly called "landing", "touchdown" or "splashdown" as well. A normal aircraft flight would include several parts of flight including taxi, takeoff, climb, cruise, descent and landing.

In aviation, a go-around is an aborted landing of an aircraft that is on final approach or has already touched down. A go-around can either be initiated by the pilot flying or requested by air traffic control for various reasons, such as an unstabilized approach or an obstruction on the runway.

Aviation is the design, development, production, operation, and use of aircraft, especially heavier-than-air aircraft. Articles related to aviation include:

An overhead join is a conventional method for an aircraft to approach and safely land at an airfield. It helps a pilot to integrate with any air traffic pattern near an airfield, join any circuit, and land.

An aerodrome or airdrome is a location from which aircraft flight operations take place, regardless of whether they involve air cargo, passengers, or neither, and regardless of whether it is for public or private use. Aerodromes include small general aviation airfields, large commercial airports, and military air bases.

A KLM Lockheed L-049 Constellation airliner crashed into high ground near Glasgow Prestwick Airport, Scotland, on 20 October 1948; all 40 aboard died. A subsequent inquiry found that the accident was likely caused by the crew's reliance on a combination of erroneous charts and incomplete weather forecasts, causing the crew to become distracted and disoriented in the inclement conditions.

Wake turbulence is a disturbance in the atmosphere that forms behind an aircraft as it passes through the air. It includes several components, the most significant of which are wingtip vortices and jet-wash, the rapidly moving gases expelled from a jet engine.

A slip is an aerodynamic state where an aircraft is moving somewhat sideways as well as forward relative to the oncoming airflow or relative wind. In other words, for a conventional aircraft, the nose will be pointing in the opposite direction to the bank of the wing(s). The aircraft is not in coordinated flight and therefore is flying inefficiently.

In aviation, an instrument approach or instrument approach procedure (IAP) is a series of predetermined maneuvers for the orderly transfer of an aircraft operating under instrument flight rules from the beginning of the initial approach to a landing, or to a point from which a landing may be made visually. These approaches are approved in the European Union by EASA and the respective country authorities and in the United States by the FAA or the United States Department of Defense for the military. The ICAO defines an instrument approach as "a series of predetermined maneuvers by reference to flight instruments with specific protection from obstacles from the initial approach fix, or where applicable, from the beginning of a defined arrival route to a point from which a landing can be completed and thereafter, if landing is not completed, to a position at which holding or en route obstacle clearance criteria apply."

A tailwind is a wind that blows in the direction of travel of an object, while a headwind blows against the direction of travel. A tailwind increases the object's speed and reduces the time required to reach its destination, while a headwind has the opposite effect.

DuPage Airport is a general aviation airport located 29 miles (47 km) west of downtown Chicago in West Chicago, DuPage County, Illinois, United States. It is owned and operated by the DuPage Airport Authority, which is an independent government body established by law by the State of Illinois. It also serves as a relief airport for O'Hare International Airport and Chicago Midway International Airport, both in nearby Chicago.

In aviation, a crosswind landing is a landing maneuver in which a significant component of the prevailing wind is perpendicular to the runway center line.

In aviation, a run and break is a procedure used by high-performance aircraft to join an airfield traffic pattern without requiring the aircraft to spend a long time flying at low speed. As such, it is a procedure normally used by military aircraft at military airfields, however because it is also used by ex-military types it may sometimes be performed at civilian airfields, although it can be seen as comedic when performed by slow moving civilian aircraft, such as a PA-28.This maneuver is also known as initial and pitch; or in the US as an overhead maneuver or overhead break.

<span class="mw-page-title-main">Final approach</span> Final stage in an aircrafts approach to landing

In aeronautics, the final approach is the last leg in an aircraft's approach to landing, when the aircraft is lined up with the runway and descending for landing. In aviation radio terminology, it is often shortened to "final".

Carroll County–Tolson Airport is a county–owned, public-use airport located one nautical mile (1.85 km) southeast of the central business district of Carrollton, a village in Carroll County, Ohio, United States. It is owned by the Carroll County Airport Authority. According to the FAA's National Plan of Integrated Airport Systems for 2009–2013, it is categorized as a general aviation airport.

Richmond Field is a privately owned, public use airport. It is located two nautical miles (4 km) southeast of the central business district of Gregory, a city in Livingston County, Michigan, United States.

A power-off accuracy approach, also known as a glide approach, is an aviation exercise used to simulate a landing with an engine failure. The purpose of this training technique is to better develop one's ability to estimate distance and glide ratios. The variation in each angle refers to the degrees an aircraft must turn to be aligned with the runway. Consideration of the wind and use of flaps are important factors in executing power-off accuracy approaches.

Ozark Air Lines Flight 965 was a scheduled commercial flight from Chicago, Illinois, to Lambert Field in St. Louis, Missouri, with a scheduled intermediate stopover at Greater Peoria Regional Airport in Peoria, Illinois. On March 27, 1968, the Douglas DC-9-15 jetliner operating the flight, carrying 44 passengers and five crew, collided in mid-air with a single-engined Cessna 150F while both aircraft were on approach to the same runway at Lambert Field. The DC-9 landed safely with no injuries to any of its 49 occupants, while both pilots in the two-person Cessna died in the collision and subsequent ground impact.

References

↑ "Airport Design: Wind Analysis" (PDF). Federal Aviation Administration. 30 September 2000. Retrieved 4 June 2021.
↑ "eCFR — Code of Federal Regulations".
↑ Federal Aviation Administration (11 February 2010). "4-3-2.c Airports with an Operating Control Tower". Aeronautical Information Manual: Official Guide to Basic Flight Information and ATC Procedures (Change 1 (26 August 2010) ed.). Washington, DC: Federal Aviation Administration. Archived from the original on 12 July 2009. Retrieved 2011-03-07.
↑ "CAAP 166-1(1): Operations in the vicinity of non-towered (non-controlled) aerodromes" (PDF). Australian Government Civil Aviation Safety Authority (CASA). p. 23. Archived from the original (PDF) on 2013-04-10. Retrieved 11 April 2013.
↑ "Chapter 14: Airport Operations". Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C ed.). Federal Aviation Administration. 2023-07-17. pp. 2–4.
↑ Transport Canada (2007-04-12). "Transport Canada Aeronautical Information Manual (TC AIM)- Rules of the Air and Air Traffic Services (RAC) 4.5.2" . Retrieved 2007-10-15.
↑ Transport Canada (2007-04-12). "Transport Canada Aeronautical Information Manual (TC AIM)- Rules of the Air and Air Traffic Services (RAC) 4.3" . Retrieved 2007-10-15.
↑ "CAA standard overhead join poster". Archived from the original on 2015-10-16. Retrieved 2008-10-29.
1 2 Federal Aviation Administration (1993-08-26). "Recommended Standards Traffic Patterns for Aeronautical Operations at Airports without Operating Control Towers". FAA Journal System (AC 90-66A). Retrieved 2007-06-05..
↑ Federal Aviation Administration (26 July 2012). "Aeronautical Information Manual – Option Approach". Archived from the original on 2012-11-04. Retrieved 8 November 2012.
1 2 "Chapter 14: Airport Operations". Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C ed.). Federal Aviation Administration. 2023-07-17. p. 20. This article incorporates text from this source, which is in the public domain .

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[1] "Airport Design: Wind Analysis" (PDF). Federal Aviation Administration. 30 September 2000. Retrieved 4 June 2021.

[2] "eCFR — Code of Federal Regulations".

[FAA_AIM_4-3-3] Federal Aviation Administration (11 February 2010). "4-3-2.c Airports with an Operating Control Tower". Aeronautical Information Manual: Official Guide to Basic Flight Information and ATC Procedures (Change 1 (26 August 2010) ed.). Washington, DC: Federal Aviation Administration. Archived from the original on 12 July 2009. Retrieved 2011-03-07.

[CASA.gov.au-4] "CAAP 166-1(1): Operations in the vicinity of non-towered (non-controlled) aerodromes" (PDF). Australian Government Civil Aviation Safety Authority (CASA). p. 23. Archived from the original (PDF) on 2013-04-10. Retrieved 11 April 2013.

[5] "Chapter 14: Airport Operations". Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C ed.). Federal Aviation Administration. 2023-07-17. pp. 2–4.

[6] Transport Canada (2007-04-12). "Transport Canada Aeronautical Information Manual (TC AIM)- Rules of the Air and Air Traffic Services (RAC) 4.5.2" . Retrieved 2007-10-15.

[7] Transport Canada (2007-04-12). "Transport Canada Aeronautical Information Manual (TC AIM)- Rules of the Air and Air Traffic Services (RAC) 4.3" . Retrieved 2007-10-15.

[8] "CAA standard overhead join poster". Archived from the original on 2015-10-16. Retrieved 2008-10-29.

[FAA_AC_90-66A-9] 1 2 Federal Aviation Administration (1993-08-26). "Recommended Standards Traffic Patterns for Aeronautical Operations at Airports without Operating Control Towers". FAA Journal System (AC 90-66A). Retrieved 2007-06-05..

[USAIM4322-10] Federal Aviation Administration (26 July 2012). "Aeronautical Information Manual – Option Approach". Archived from the original on 2012-11-04. Retrieved 8 November 2012.

[phak-11] 1 2 "Chapter 14: Airport Operations". Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C ed.). Federal Aviation Administration. 2023-07-17. p. 20. This article incorporates text from this source, which is in the public domain .

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]