Baldwin 60000

Last updated
Baldwin 60000
Baldwin 60000 locomotive - Franklin Institute - DSC06720.JPG
Baldwin 60000 in the Franklin Institute
Type and origin
Power typeSteam
Builder Baldwin Locomotive Works
Serial number60000
Model16-3-48/48-1/4-F
Build date1926
Specifications
Configuration:
   Whyte 4-10-2
   UIC 2′E1′ h3v
Gauge 4 ft 8+12 in (1,435 mm) standard gauge
Leading dia. 33 in (838 mm)
Driver dia.63.5 in (1,613 mm)
Trailing dia. 45.5 in (1,156 mm)
Adhesive weight 338,400  lb (153,500  kg; 153.5  t)
Loco weight457,500 lb (207,500 kg; 207.5 t)
Total weight700,900 lb (317,900 kg; 317.9 t)
Fuel type Coal (Briefly converted to oil)
Fuel capacity32,000 lb (15,000 kg; 15 t)
Water cap.12,000 US gallons (45,000 L; 10,000 imp gal)
Firebox:
  Grate area82.5 sq ft (7.66 m2)
Boiler84 in (2,134 mm)
Boiler pressure350 psi (2.41 MPa)
Heating surface:
  Firebox745 sq ft (69.2 m2)
  Tubes and flues5,192 sq ft (482.4 m2)
Superheater:
  Heating area1,357 sq ft (126.1 m2)
Cylinders Center: 1 HP
Outside: 2 LP
High-pressure cylinder27 in × 32 in (686 mm × 813 mm)
Low-pressure cylinder27 in × 32 in (686 mm × 813 mm)
Valve type14 in (356 mm) piston valves
Performance figures
Maximum speed70 mph (110 km/h)
Power output4,515 hp (3.37 MW)
Tractive effort 82,500 lbf (367.0 kN)
Career
OperatorsBaldwin Locomotive Works
NicknamesBaldwin Boomer
RetiredStored: 1928,
Sold: 1933
Current owner Franklin Institute Science Museum
DispositionIndoor stationary display - until the mid 2010s, it moved back and forth 15 feet (4.6 m) on a short track powered by hydraulics [1]

Baldwin 60000 is an experimental steam locomotive built by the Baldwin Locomotive Works in Eddystone, Pennsylvania, in 1926, during the height of the railroading industry. It received its number for being the 60,000th locomotive built by Baldwin. [2]

It was designed to be the best locomotive that Baldwin ever made. It has three cylinders, weighs about 350 short tons (318 t; 313 long tons), including tender, and can pull a load of up to 7,000 short tons (6,400 t; 6,200 long tons). Its top speed is 70 mph (110 km/h).[ citation needed ]

60000 was highly innovative, carrying unusual technology such as a water-tube firebox. This was intended to improve efficiency but the tubes were prone to burst inside the firebox. It is also a compound, expanding the steam once in the inside cylinder and then again in the two outside cylinders. Although compounding increases efficiency, it was an extra complication that the US railroads had mostly rejected by the middle twenties. [3] The weight and length of the engine were too much for all but the heaviest and straightest tracks.

This locomotive was experimental and was meant to be the model for future development. However, its demonstration runs never persuaded railroads to purchase more. In 1933, it was donated to the Franklin Institute Science Museum in Philadelphia, Pennsylvania [1] and remains there today.

Testing

After a series of brief test runs following construction, the 60000 was sent to the Pennsylvania Railroad's Altoona Test Plant in Altoona, Pennsylvania. Placed on rollers without its tender, it was tested on the traction dynamometer to measure its performance, which included maximum drawbar horsepower. [4] Following tests at the Altoona Test Plant, the Pennsylvania Railroad placed the engine in freight service between Enola Yard near Harrisburg and Morrisville Yard via the Trenton Cutoff. During testing on the PRR, 60000 pulled a maximum of 7,700 tons. [5]

Following testing on the PRR, the 60000 was sent for additional testing on the Baltimore and Ohio Railroad. Between November and December 1926, the 60000 was tested on the Cumberland Division between Brunswick and Keyser, Maryland, the Connellsville Division between Cumberland, Maryland, and Connellsville, Pennsylvania, and the Pittsburgh Division, which included the Sand Patch and Seventeen-Mile grades. [6]

In February 1927, the 60000 was sent to the Chicago, Burlington and Quincy Railroad's Beardstown Division of Illinois. The 60000 was run in tandem with the CB&Q's own M2-A Class 2-10-2 number 6157, in order to compare coal and water consumption. Overall, the 60000 was superior in its coal and water consumption. [6]

On 24 February 1927, the 60000 was sent to the Atchison, Topeka and Santa Fe Railroad. Testing was performed on the Pecos division between Clovis and Belen, New Mexico. As with the CB&Q, the AT&SF compared the performance of the 60000 with that of its own power in the form of two 3800-Class 2-10-2s. Once more the 60000 demonstrated superior fuel consumption than the locomotives of the host railroad. [6]

In the summer and fall of 1927, the 60000 was sent to the Southern Pacific Railroad, which overhauled the locomotive and converted it to an oil burner at its Sacramento Shops. Following its conversion, the 60000 was tested in both freight and passenger service on the Sacramento Division, during which the engine carried a Southern Pacific tender. Following tests on the SP, the 60000 was sent to the Great Northern Railway between Everett, Washington and Minot, North Dakota. Overall, the 60000 did not perform as well on oil as it did on coal. [6]

Converted back to coal, the 60000 was then returned to the Baldwin Locomotive Works and used as a stationary boiler before being donated to the Franklin Institute. [1] The locomotive was moved from the Baltimore and Ohio Railroad tracks at 24th and Vine Street over temporary tracks to the museum building which was then still under construction. [7] The locomotive was placed in the building through an opening in the western wall. [8]

Related Research Articles

The Pennsylvania Railroad, legal name The Pennsylvania Railroad Company, also known as the "Pennsy", was an American Class I railroad that was established in 1846 and headquartered in Philadelphia. It was named for the commonwealth in which it was established. At its peak in 1882, the Pennsylvania Railroad was the largest railroad, the largest transportation enterprise, and the largest corporation in the world.

<span class="mw-page-title-main">2-10-4</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives, a 2-10-4 locomotive has two leading wheels on one axle, usually in a Bissel truck, ten coupled driving wheels on five axles, and four trailing wheels on two axles, usually in a bogie. These were referred to as the Texas type in most of the United States, the Colorado type on the Burlington Route, and the Selkirk type in Canada.

<span class="mw-page-title-main">2-8-8-4</span> Articulated locomotive wheel arrangement

A 2-8-8-4 steam locomotive, under the Whyte notation, has two leading wheels, two sets of eight driving wheels, and a four-wheel trailing truck. The type was generally named the Yellowstone, a name given it by the first owner, the Northern Pacific Railway, whose lines ran near Yellowstone National Park. Seventy-two Yellowstone-type locomotives were built for four U.S. railroads.

<span class="mw-page-title-main">Pennsylvania Railroad K4 class</span> Class of 425 American 4-6-2 locomotives

The Pennsylvania Railroad (PRR) K4 4-6-2 "Pacific" was its premier passenger-hauling steam locomotive from 1914 through the end of steam on the PRR in 1957.

<span class="mw-page-title-main">Pennsylvania Railroad I1 class</span>

The Pennsylvania Railroad (PRR) class I1s steam locomotives were the largest class of 2-10-0 "Decapods" in the United States. From 1916 to 1923, 598 locomotives were produced. They were the dominant freight locomotive on the system until World War II and remained in service until 1957. Nicknames for the type included Decs and Hippos, the latter due to their large boiler.

<span class="mw-page-title-main">Pennsylvania Railroad class M1</span>

The M1 was a class of steam locomotive of the Pennsylvania Railroad (PRR). It was a class of heavy mixed-traffic locomotives of the 4-8-2 "Mountain" arrangement, which uses four pairs of driving wheels with a four-wheel guiding truck in front for stability at speed and a two-wheel trailing truck to support the large firebox needed for sustained power. Although built for both passenger and freight work, they spent most of their service lives hauling heavy high-speed freight trains. Many PRR men counted the M1 class locomotives as the best steam locomotives the railroad ever owned.

<span class="mw-page-title-main">Pennsylvania Railroad class T1</span> Class of 52 4-4-4-4 duplex locomotives

The Pennsylvania Railroad (PRR) class T1 duplex-drive 4-4-4-4 steam locomotives, introduced in 1942 with two prototypes and later in 1945-1946 with 50 production examples, were the last steam locomotives built for the PRR and arguably its most controversial. They were ambitious, technologically sophisticated, powerful, fast and distinctively streamlined by Raymond Loewy. However, they were also prone to wheelslip both when starting and at speed, in addition to being complicated to maintain and expensive to run. The PRR decided in 1948 to place diesel locomotives on all express passenger trains, leaving unanswered questions as to whether the T1's flaws were solvable, especially taking into account that the two prototypes did not have the problems inherent to the production units.

<span class="mw-page-title-main">4-4-4-4</span> Duplex locomotive wheel arrangement

A 4-4-4-4 steam locomotive, in the Whyte notation for describing locomotive wheel arrangements, has a four-wheel leading truck, two sets of four driving wheels, and a four-wheel trailing truck. While it would be possible to make an articulated locomotive of this arrangement, the only 4-4-4-4s ever built were duplex locomotives—with two sets of cylinders driving two sets of driven wheels in one rigid frame, essentially a 4-8-4 with divided drive.

<span class="mw-page-title-main">Pennsylvania Railroad class B6</span>

The Pennsylvania Railroad's class B6 was its most successful class of switcher locomotive, or as the PRR termed them "shifter". The PRR preferred the 0-6-0 wheel arrangement for larger switchers, whereas on other railroads the 0-8-0 gained preference. The PRR generally used 2-8-0s when larger power was required.

<span class="mw-page-title-main">Pennsylvania Railroad class S2</span> American steam turbine locomotive

The Pennsylvania Railroad's S2 class was a steam turbine locomotive designed and built in a collaborative effort by Baldwin Locomotive Works and Westinghouse Electric & Manufacturing Company, as an attempt to prolong the dominance of the steam locomotive by adapting technology that had been widely accepted in the marine industry. One was built, #6200, delivered in September 1944. The S2 was the sole example of the 6-8-6 wheel arrangement in the Whyte notation, with a six-wheel leading truck keeping the locomotive stable at speed, eight powered and coupled driving wheels, and a six-wheel trailing truck supporting the large firebox. The S2 used a direct-drive steam turbine provided by the Westinghouse Electric & Manufacturing Company, geared to the center pair of axles with the outer two axles connected by side rods; the fixed gear ratio was 18.5:1. Such design was to prevent energy loss and S2 achieved a mechanical efficiency of 97% which means only 3% of steam energy was lost within the propulsion equipment. The disadvantage of a direct-drive steam turbine was that the turbine could not operate at optimal speeds over the locomotive's entire speed range. The S2 was the largest, heaviest and fastest direct-drive turbine locomotive design ever built.

The Pennsylvania Railroad's class K5 were experimental 4-6-2 "Pacific" types, built in 1929 to see if a larger Pacific than the standard K4s was worthwhile. Two prototypes were built, #5698 at the PRR's own Altoona Works, and #5699 by the Baldwin Locomotive Works. Although classified identically, the two locomotives differed in many aspects, as detailed below. They were both fitted with a much fatter boiler than the K4s, but dimensionally similar to those of the I1s 2-10-0 "Decapods". Most other dimensions were enlarged over the K4s as well; the exceptions being the 70 square feet (6.5 m2) grate area and the 80 in (2.032 m) drivers.

<span class="mw-page-title-main">Pennsylvania Railroad class S1</span> Experimental American 6-4-4-6 duplex locomotive

The PRR S1 class steam locomotive was a single experimental duplex locomotive of the Pennsylvania Railroad. It was designed to demonstrate the advantages of duplex drives espoused by Baldwin Chief Engineer Ralph P. Johnson. The S1 class was the largest steam locomotive ever built. The streamlined Art Deco styled shell of the locomotive was designed by Raymond Loewy.

The Pennsylvania Railroad class Q1, #6130, was a single experimental steam locomotive designed for dual service. The locomotive entered service in 1942, and retired in 1949 after accumulating a relatively low 165,000 service miles.

<span class="mw-page-title-main">Pennsylvania Railroad L1 class</span> Class of 574 American 2-8-2 locomotives

Pennsylvania Railroad Class L1s were 2-8-2 "Mikado"-type steam locomotives that were used on the Pennsylvania Railroad during the early twentieth century. These 574 locomotives were manufactured between 1914 and 1919 by the railroad's own Juniata Shops as well as the Baldwin Locomotive Works (205) and the Lima Locomotive Works (25).

The Pennsylvania Railroad's steam locomotive class D4 (formerly Class C (anthracite), pre-1895) comprised thirty-seven anthracite-burning 4-4-0 locomotives intended for general passenger and freight service on the PRR's New Jersey lines, constructed at the railroad's own Altoona Works (now owned by Norfolk Southern) during 1873–1890. They shared many parts with other standard classes.

<span class="mw-page-title-main">Altoona Works</span> Railroad complex in Altoona, Pennsylvania, U.S.

Altoona Works is a large railroad industrial complex in Altoona, Pennsylvania. It was built between 1850 and 1925 by the Pennsylvania Railroad (PRR), to supply the railroad with locomotives, railroad cars and related equipment. For many years, it was the largest railroad shop complex in the world.

<span class="mw-page-title-main">Pennsylvania Railroad 1361</span> Preserved PRR K4 class 4-6-2 locomotive

Pennsylvania Railroad 1361 is a 4-6-2 K4 "Pacific" type steam locomotive built in May 1918 by the Pennsylvania Railroad's (PRR) Juniata Shops in Altoona, Pennsylvania. It hauled mainline passenger trains in Pennsylvania and commuter trains in Central New Jersey on the PRR until its retirement from revenue service in 1956. Restored to operating condition for excursion service in 1987, No. 1361 and its only surviving sister locomotive, No. 3750, were designated as the official state steam locomotives by the Pennsylvania General Assembly. In 1988, it was sidelined due to mechanical problems and was currently owned by the Railroaders Memorial Museum (RMM) in Altoona, Pennsylvania, who were currently getting No. 1361 back to operation.

<span class="mw-page-title-main">Duplex locomotive</span> Type of steam locomotive

A duplex locomotive is a steam locomotive that divides the driving force on its wheels by using two pairs of cylinders rigidly mounted to a single locomotive frame; it is not an articulated locomotive. The concept was first used in France in 1863, but was particularly developed in the early 1930s by the Baldwin Locomotive Works, the largest commercial builder of steam locomotives in North America, under the supervision of its then chief engineer, Ralph P. Johnson.

<span class="mw-page-title-main">Pennsylvania Railroad 5550</span> PRR T-1 class 4-4-4-4 locomotive under construction

Pennsylvania Railroad 5550 is a mainline duplex drive steam locomotive under construction in the United States. With an estimated completion by 2030, the locomotive will become the 53rd example of the Pennsylvania Railroad's T1 steam locomotive class and the only operational locomotive of its type, as well as the largest steam locomotive built in the United States since 1952. The estimated cost of PRR 5550 was originally $10 million, but an updated projected cost of $7 million was released with the acquisition of an existing long-haul tender from the Western New York Railway Historical Society in August 2017. Construction began in 2014 with the casting of the locomotive's keystone-shaped number plate. As of February 2024 the locomotive was 43% complete.

The Pennsylvania Railroad's class K29s comprised a single experimental 4-6-2 "Pacific" type steam locomotive. Constructed by Alco-Schenectady, it was given road number 3395. Although only one demonstrator was constructed, the K29s would become the basis for the highly successful K4s Pacifics and L1s Mikados. The lone example spent most of its life on the PRR's Pittsburgh division main line and was retired around 1929.

References

  1. 1 2 3 Dobrin, Peter (4 June 2019). "Franklin Institute locomotive is going to perch overhead in a $6 million train room renovation". Philadelphia Inquirer. Philadelphia, Pennsylvania. Retrieved 5 September 2020.
  2. Douglas Self. "Baldwin 60000". Loco Locomotive gallery.
  3. C.B. Peck (ed.). 1950-52 Locomotive Cyclopedia of American Practice. New York: Simmons-Boardman. pp. 500–538. Of 102 locomotives listed in detail, only 2 were compound, the N&W Y6 and the C&O H-6.
  4. Fry, Lawford H. "Discussion of Tests of Locomotive 60,000". Cyberspace World Railroad.
  5. "Pennsylvania Railroad Test Department - Extracts from Reports on Tests of Locomotive 60,000". Cyberspace World Railroad.
  6. 1 2 3 4 "Baltimore & Ohio Railroad". Cyberspace World Railroad.
  7. "Image of Baldwin 6000 on temporary tracks". Facebook . Retrieved 5 September 2020.
  8. "Image of opened wall for Baldwin 6000". Facebook . Retrieved 5 September 2020.